LTC6990
TimerBlox: Voltage Controlled
Silicon Oscillator
FEATURES
DESCRIPTION
Fixed-Frequency or Voltage-Controlled Operation
n Fixed: Single Resistor Programs Frequency with
300kHz at 1MHz
n CMOS Logic Output Sources/Sinks 20mA
n 50% Duty Cycle Square Wave Output
n Output Enable (Selectable Low or Hi-Z When Disabled)
n 55°C to 125°C Operating Temperature Range
n Available in Low Profile (1mm) SOT-23 (ThinSOT™)
and 2mm × 3mm DFN Package
n AEC-Q100 Qualified for Automotive Applications
The LTC®6990 is a precision silicon oscillator with a programmable frequency range of 488Hz to 2MHz. It can be
used as a fixed-frequency or voltage-controlled oscillator
(VCO). The LTC6990 is part of the TimerBlox® family of
versatile silicon timing devices.
n
APPLICATIONS
Low Cost Precision Programmable Oscillator
n Voltage-Controlled Oscillator
n High Vibration, High Acceleration Environments
n Replacement for Fixed Crystal and Ceramic Oscillators
n Portable and Battery-Powered Equipment
n
All registered trademarks and trademarks are the property of their respective owners. Protected
by U.S. patents, including 6342817, 6614313.
A single resistor, RSET, programs the LTC6990’s internal master oscillator frequency. The output frequency
is determined by this master oscillator and an internal
frequency divider, NDIV, programmable to eight settings
from 1 to 128.
fOUT =
1MHz 50kΩ
•
, NDIV = 1, 2, 4 …128
NDIV R SET
Optionally, a second resistor at the SET input provides
linear voltage control of the output frequency and can be
used for frequency modulation. A narrow or wide VCO
tuning range can be configured by the appropriate selection of the two resistors.
The LTC6990 includes an enable function that is synchronized with the master oscillator to ensure clean, glitchfree output pulses. The disabled output can be configured
to be high impedance or forced low.
For easy configuration of the LTC6990, use the TimerBlox
LTC6990: Voltage Controlled Oscillator Web-Based
Design Tool.
TYPICAL APPLICATION
Voltage Controlled Oscillator with 16:1 Frequency Range
VCO Transfer Function
1000
fOUT = 2MHz − VCTRL •
V+
LTC6990
GND
VCTRL
V+
V+
C1
0.1µF
RVCO
100k
SET
RSET
100k
V
750
OUT
fOUT (kHz)
OE
MHz
DIV
500
250
6990 TA01a
0
0
0.5
1
VCTRL (V)
1.5
2
6990 TA01b
Rev. D
Document Feedback
For more information www.analog.com
1
LTC6990
ABSOLUTE MAXIMUM RATINGS
(Note 1)
Supply Voltage (V+) to GND.........................................6V
Maximum Voltage on Any Pin
.............................. (GND – 0.3V) ≤ VPIN ≤ (V+ + 0.3V)
Operating Temperature Range (Note 2)
LTC6990C.............................................–40°C to 85°C
LTC6990I..............................................–40°C to 85°C
LTC6990H........................................... –40°C to 125°C
LTC6990MP........................................ –55°C to 125°C
Specified Temperature Range (Note 3)
LTC6990C................................................. 0°C to 70°C
LTC6990I..............................................–40°C to 85°C
LTC6990H........................................... –40°C to 125°C
LTC6990MP........................................ –55°C to 125°C
Junction Temperature............................................ 150°C
Storage Temperature Range................... –65°C to 150°C
Lead Temperature (Soldering, 10sec).................... 300°C
PIN CONFIGURATION
TOP VIEW
TOP VIEW
V+ 1
DIV 2
6 OUT
7
SET 3
OE 1
5 GND
6 OUT
GND 2
5 V+
SET 3
4 DIV
4 OE
DCB PACKAGE
6-LEAD (2mm × 3mm) PLASTIC DFN
S6 PACKAGE
6-LEAD PLASTIC TSOT-23
TJMAX = 150°C, θJA = 64°C/W, θJC = 10.6°C/W
EXPOSED PAD (PIN 7) CONNECTED TO GND,
PCB CONNECTION OPTIONAL
TJMAX = 150°C, θJA = 192°C/W, θJC = 51°C/W
ORDER INFORMATION
Lead Free Finish
TAPE AND REEL (MINI)
TAPE AND REEL
PART MARKING*
PACKAGE DESCRIPTION
SPECIFIED TEMPERATURE RANGE
LTC6990CDCB#TRMPBF
LTC6990CDCB#TRPBF
LDWX
6-Lead (2mm × 3mm) Plastic DFN
0°C to 70°C
LTC6990IDCB#TRMPBF
LTC6990IDCB#TRPBF
LDWX
6-Lead (2mm × 3mm) Plastic DFN
–40°C to 85°C
LTC6990HDCB#TRMPBF
LTC6990HDCB#TRPBF
LDWX
6-Lead (2mm × 3mm) Plastic DFN
–40°C to 125°C
LTC6990CS6#TRMPBF
LTC6990CS6#TRPBF
LTDWW
6-Lead Plastic TSOT-23
0°C to 70°C
LTC6990IS6#TRMPBF
LTC6990IS6#TRPBF
LTDWW
6-Lead Plastic TSOT-23
–40°C to 85°C
LTC6990HS6#TRMPBF
LTC6990HS6#TRPBF
LTDWW
6-Lead Plastic TSOT-23
–40°C to 125°C
LTC6990MPS6#TRMPBF
LTC6990MPS6#TRPBF
LTDWW
6-Lead Plastic TSOT-23
–55°C to 125°C
LTC6990IS6#WTRPBF
LTDWW
6-Lead Plastic TSOT-23
–40°C to 85°C
AUTOMOTIVE PRODUCTS**
LTC6990IS6#WTRMPBF
LTC6990HS6#WTRMPBF LTC6990HS6#WTRPBF LTDWW
6-Lead Plastic TSOT-23
–40°C to 125°C
Contact the factory for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container.
Tape and reel specifications. Some packages are available in 500 unit reels through designated sales channels with #TRMPBF suffix.
**Versions of this part are available with controlled manufacturing to support the quality and reliability requirements of automotive applications. These
models are designated with a #W suffix. Only the automotive grade products shown are available for use in automotive applications. Contact your
local Analog Devices account representative for specific product ordering information and to obtain the specific Automotive Reliability reports for
these models.
2
Rev. D
For more information www.analog.com
LTC6990
ELECTRICAL
CHARACTERISTICS
The
l denotes the specifications which apply over the full operating
+
+
temperature range, otherwise specifications are at TA = 25°C. Test conditions are V = 2.25V to 5.5V, OE = V , DIVCODE = 0 to 15
(NDIV = 1 to 128), RSET = 50k to 800k, RLOAD = 5k, CLOAD = 5pF unless otherwise noted.
SYMBOL
PARAMETER
CONDITIONS
MIN
fOUT
Output Frequency
Recommended Range: RSET = 50k to 800k
Extended Range: RSET = 25k to 800k
0.488
0.488
∆fOUT
Frequency Accuracy (Note 4)
Recommended Range
RSET = 50k to 800k
Extended Range
RSET = 25k to 800k
∆fOUT/∆T
∆fOUT/∆V+
Frequency Drift Over Temperature
TYP
MAX
UNITS
1000
2000
kHz
kHz
l
±1.5
±2.2
%
%
l
±2.4
±3.2
%
%
±0.8
l
±0.005
l
l
0.23
0.06
%/°C
Frequency Drift Over Supply
V+ = 4.5V to 5.5V
V+ = 2.25V to 4.5V
Long-Term Frequency Stability
(Note 11)
90
Period Jitter (Note 10)
NDIV = 1
0.38
%P-P
NDIV = 2
0.22
0.027
%P-P
%RMS
NDIV = 128
0.022
0.004
%P-P
%RMS
Duty Cycle
BW
Frequency Modulation Bandwidth
tS
Frequency Change Settling Time
(Note 9)
NDIV = 1, RSET = 25k to 800k
NDIV > 1, RSET = 25k to 800k
l
l
47
48
tMASTER = tOUT /NDIV
50
50
0.55
0.16
%/V
%/V
ppm/√kHr
53
52
%
%
0.4•fOUT
kHz
6•tMASTER
µs
Analog Inputs
VSET
Voltage at SET Pin
l
∆VSET /∆T
VSET Drift Over Temperature
l
∆VSET /∆V+
VSET Drift Over Supply
∆VSET /∆ISET VSET Droop with ISET
RSET
Frequency-Setting Resistor
VDIV
∆VDIV
1.00
1.03
Recommended Range
Extended Range
V
±75
µV/°C
–150
µV/V
–7
Ω
l
l
50
25
800
800
kΩ
kΩ
l
0
V+
V
l
±1.5
%
DIV Pin Input Current
l
±10
nA
Operating Supply Voltage Range
l
5.5
V
1.95
V
DIV Pin Voltage
/V+
0.97
DIV Pin Valid Code Range (Note 5)
Deviation from Ideal VDIV/V+ = (DIVCODE + 0.5)/16
Power Supply
V+
IS
2.25
Power-On Reset Voltage
RSET = 25k to 800k
l
Supply Current
RL = ∞, NDIV = 1, RSET = 50k V+ = 5.5V
V+ = 2.25V
l
l
235
145
283
183
µA
µA
RL = ∞, NDIV = 1 RSET = 800k V+ = 5.5V
V+ = 2.25V
l
l
71
59
105
92
µA
µA
RL = ∞, NDIV = 128, RSET = 50k V+ = 5.5V
V+ = 2.25V
l
l
137
106
180
145
µA
µA
RL = ∞, NDIV = 128, RSET = 800k V+ = 5.5V
V+ = 2.25V
l
l
66
56
100
90
µA
µA
Rev. D
For more information www.analog.com
3
LTC6990
ELECTRICAL
CHARACTERISTICS
The
l denotes the specifications which apply over the full operating
+
+
temperature range, otherwise specifications are at TA = 25°C. Test conditions are V = 2.25V to 5.5V, OE = V , DIVCODE = 0 to 15
(NDIV = 1 to 128), RSET = 25k to 800k, RLOAD = ∞, CLOAD = 5pF unless otherwise noted.
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
±10
nA
Digital I/O
OE Pin Input Capacitance
2.5
OE Pin Input Current
OE = 0V to V+
l
VIH
High Level OE Pin Input Voltage
(Note 6)
l
VIL
Low Level OE Pin Input Voltage
(Note 6)
l
OUT Pin Hi-Z Leakage
OE = 0V, DIVCODE ≥ 8, OUT = 0V to V+
IOUT(MAX)
Maximum Output Current
VOH
High Level Output Voltage
(Note 7)
VOL
Low Level Output Voltage
(Note 7)
0.7•V+
V
0.3•V+
V
±10
µA
±20
mA
V+ = 5.5V IOH = –1mA
IOH = –16mA
l
l
5.45
4.84
5.48
5.15
V
V
V+ = 3.3V IOH = –1mA
IOH = –10mA
l
l
3.24
2.75
3.27
2.99
V
V
V+ = 2.25V IOH = –1mA
IOH = –8mA
l
l
2.17
1.58
2.21
1.88
V
V
V+ = 5.5V IOL = 1mA
IOL = 16mA
l
l
0.02
0.26
0.04
0.54
V
V
V+ = 3.3V IOL = 1mA
IOL = 10mA
l
l
0.03
0.22
0.05
0.46
V
V
V+ = 2.25V IOL = 1mA
IOL = 8mA
l
l
0.03
0.26
0.07
0.54
V
V
tPD
Output Disable Propagation Delay V+ = 5.5V
V+ = 3.3V
V+ = 2.25V
tENABLE
Output Enable Time
NDIV ≤ 2, tOUT = 1/fOUT
NDIV ≥ 4, tMASTER = tOUT/NDIV
tr
Output Rise Time (Note 8)
tf
Output Fall Time (Note 8)
17
26
44
ns
ns
ns
tPD to tOUT
tPD to 2•tMASTER
µs
µs
V+ = 5.5V
V+ = 3.3V
V+ = 2.25V
1.1
1.7
2.7
ns
ns
ns
V+ = 5.5V
V+ = 3.3V
V+ = 2.25V
1.0
1.6
2.4
ns
ns
ns
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2: The LTC6990C is guaranteed functional over the operating
temperature range of –40°C to 85°C.
Note 3: The LTC6990C is guaranteed to meet specified performance from
0°C to 70°C. The LTC6990C is designed, characterized and expected to
meet specified performance from –40°C to 85°C but it is not tested or
QA sampled at these temperatures. The LTC6990I is guaranteed to meet
specified performance from –40°C to 85°C. The LTC6990H is guaranteed
to meet specified performance from –40°C to 125°C. The LTC6990MP is
guaranteed to meet specified performance from –55°C to 125°C.
Note 4: Frequency accuracy is defined as the deviation from the fOUT
equation, assuming RSET is used to program the frequency.
4
pF
Note 5: See Operation section, Table 1 and Figure 2 for a full explanation
of how the DIV pin voltage selects the value of DIVCODE.
Note 6: The OE pin has hysteresis to accommodate slow rising or falling
signals. The threshold voltages are proportional to V+. Typical values can
be estimated at any supply voltage using VOE(RISING) ≈ 0.55 • V+ + 185mV
and VOE(FALLING) ≈ 0.48 • V+ – 155mV.
Note 7: To conform to the Logic IC Standard, current out of a pin is
arbitrarily given a negative value.
Note 8: Output rise and fall times are measured between the 10% and the
90% power supply levels with 5pF output load. These specifications are
based on characterization.
Note 9: Settling time is the amount of time required for the output to settle
within ±1% of the final frequency after a 0.5x or 2x change in ISET.
Note 10: Jitter is the ratio of the deviation of the period to the mean of the
period. This specification is based on characterization and is not 100% tested.
Rev. D
For more information www.analog.com
LTC6990
ELECTRICAL CHARACTERISTICS
Note 11: Long-term drift of silicon oscillators is primarily due to the
movement of ions and impurities within the silicon and is tested at 30°C
under otherwise nominal operating conditions. Long-term drift is specified
as ppm/√kHr due to the typically nonlinear nature of the drift. To calculate
drift for a set time period, translate that time into thousands of hours, take
the square root and multiply by the typical drift number. For instance, a
year is 8.77kHr and would yield a drift of 266ppm at 90ppm/√kHr. Drift
without power applied to the device may be approximated as 1/10th of the
drift with power, or 9ppm/√kHr for a 90ppm/√kHr device.
TYPICAL PERFORMANCE CHARACTERISTICS
0.5
1
TYPICAL MAX
0
90% OF UNITS
–1
TYPICAL MIN
–2
10
100
RSET (kΩ)
RSET = 800k
0.2
0
RSET = 200k
–0.1
–0.2
–0.5
RSET = 50k
0.0
RSET = 50k
RSET = 267k
–1.0
2
3
4
5
SUPPLY VOLTAGE (V)
6990 G01
–1.5
–50
6
–25
6990 G02
0
25
50
75
TEMPERATURE (°C)
100
125
6990 G03
VSET vs Supply Voltage
1.003
V+ = 3.3V
TA = 25°C
RSET = 800k
–0.5
–0.4
1000
V+ = 3.3V
DIVCODE = 4
0.5
0.1
VSET vs ISET
1.003
1.0
0.3
–0.3
GUARANTEED MIN
OVER TEMPERATURE
–3
–4
FREQUENCY ERROR (%)
2
TA = 25°C
0.4
GUARANTEED MAX
OVER TEMPERATURE
Frequency Error vs Temperature
1.5
ERROR (%)
TA = 25°C
3
FREQUENCY ERROR (%)
Frequency Error
vs Supply Voltage
Frequency Error vs RSET
4
V+ = 3.3V, unless otherwise noted.
VSET vs Temperature
1.020
RSET = 200k
1.015 3 TYPICAL PARTS
RSET = 200k
TA = 25°C
1.010
VSET (V)
VSET (V)
VSET (V)
1.002
1.002
1.000
0.995
1.001
1.001
1.005
0.990
0.985
1.000
0
10
20
ISET (µA)
30
40
1.000
2
3
4
5
SUPPLY VOLTAGE (V)
6
6990 G05
6990 G04
0.980
–50
–25
0
25
50
75
TEMPERATURE (°C)
100
125
6990 G06
Rev. D
For more information www.analog.com
5
LTC6990
TYPICAL PERFORMANCE CHARACTERISTICS
200
150
100
50
0.994
1.002
1.010
VSET (V)
100
RSET = 800k, ÷1
50
÷128
100
0
0.1
V+ = 5V
TA = 25°C
1
10
100
1000
FREQUENCY (kHz)
÷1
÷2
200
150
÷128
100
0
0.1
10000
1
10
100
1000
FREQUENCY (kHz)
OE PIN VOLTAGE (V)
JITTER (%P-P)
0
0.1
1
10
100
FREQUENCY (kHz)
1000
6990 G13
6
100
3.3V, OE FALLING
125
3.3V,
OE RISING
100
75
0
20
40
60
VOE /V+ (%)
80
100
6990 G12
TA = 25°C
45
2.5
NEGATIVE-GOING
1.5
1.0
0
5V, OE RISING
50
TA = 25°C
2.0
125
Output Resistance
vs Supply Voltage
0.5
÷128
0
25
50
75
TEMPERATURE (°C)
5V, OE FALLING
150
50
10000
POSITIVE-GOING
÷4
–25
TA = 25°C
RSET = 800k
175 DIVCODE = 7
OE Threshold Voltage
vs Supply Voltage
÷1
÷2
2.25V, RSET = 800k, ÷128
Supply Current vs OE Pin Voltage
3.0
0.10
0.05
50
6990 G11
3.5
0.30
0.15
5.5V, RSET = 800k, ÷1
6990 G09
V+ = 2.5V
TA = 25°C
50
0.50
0.20
100
200
250
Peak-to-Peak Jitter vs Frequency
TA = 25°C
0.45 V+ = 5V
PEAK-TO-PEAK PERIOD
0.40 DEVIATION MEASURED
0.35 OVER 30sec INTERVALS
5.5V, RSET = 50k, ÷128
0
–50
6
300
6990 G10
0.25
4
5
SUPPLY VOLTAGE (V)
RECOMMENDED RANGE
EXTENDED RANGE
350
÷1
50
3
2.25V, RSET = 50k, ÷1
150
Supply Current vs Frequency, 2.5V
200
150
2
400
÷2
250
RSET = 800k, ÷128
6990 G07
POWER SUPPLY CURRNET (µA)
POWER SUPPLY CURRNET (µA)
300
RSET = 50k, ÷128
200
6990 G05
RECOMMENDED RANGE
EXTENDED RANGE
350
5.5V, RSET = 50k, ÷1
RSET = 50k, ÷2
150
Supply Current vs Frequency, 5V
400
RSET = 50k, ÷1
200
0
1.018
TA = 25°C
POWER SUPPLY CURRENT (µA)
0.986
Supply Current vs Temperature
250
OUTPUT RESISTANCE (Ω)
0
POWER SUPPLY CURRENT (µA)
TA = 25°C
2 LOTS
DFN AND SOT-23
1416 UNITS
250
NUMBER OF UNITS
Supply Current vs Supply Voltage
250
POWER SUPPLY CURRENT (µA)
Typical VSET Distribution
300
V+ = 3V, unless otherwise noted.
40
35
OUTPUT SOURCING CURRENT
30
25
20
OUTPUT SINKING CURRENT
15
10
5
2
3
4
5
SUPPLY VOLTAGE (V)
6
6990 G14
0
2
3
4
5
SUPPLY VOLTAGE (V)
6
6990 G15
Rev. D
For more information www.analog.com
LTC6990
TYPICAL PERFORMANCE CHARACTERISTICS
Rise and Fall Time
vs Supply Voltage
Typical Frequency Error vs
Time (Long-Term Drift)
RISE/FALL TIME (ns)
50
0
–50
–100
TA = 25°C
CLOAD = 5pF
45
2.0
tRISE
1.5
tFALL
1.0
0.5
–150
–200
50
TA = 25°C
CLOAD = 5pF
2.5
100
40
35
30
25
20
15
10
5
0
400
800 1200 1600 2000 2400 2800
TIME (h)
0
2
3
4
5
SUPPLY VOLTAGE (V)
6
6990 G15a
1000
0
2
6990 G16
Typical ISET Current Limit vs V+
3
4
5
SUPPLY VOLTAGE (V)
6
6990 G17
Typical Output Waveform
V+ = 3.3V
DIVCODE = 2
RSET = 200k
TA = 25°C
SET PIN SHORTED TO GND
800
ISET (µA)
DELTA FREQUENCY (ppm)
3.0
65 UNITS
SOT-23 AND DFN PARTS
TA = 30°C
150
Output Disable Propagation Delay
(tPD) vs Supply Voltage
PROPAGATION DELAY (ns)
200
V+ = 3V, unless otherwise noted.
600
OE
2V/DIV
400
OUT
2V/DIV
200
0
2
3
4
5
SUPPLY VOLTAGE (V)
20µs/DIV
6
6990 G19
6990 G18
Frequency Modulation
Frequency Modulation
VCTRL
2V/DIV
VCTRL
2V/DIV
OUT
2V/DIV
OUT
2V/DIV
fOUT
50kHz/DIV
fOUT
50kHz/DIV
20µs/DIV
V+ = 3.3V, DIVCODE = 0
RSET = 200k, RVCO = 464k
fOUT = 175kHz to 350kHz
6990 G20
20µs/DIV
V+ = 3.3V, DIVCODE = 0
RSET = 200k, RVCO = 464k
fOUT = 175kHz to 350kHz
6990 G21
Rev. D
For more information www.analog.com
7
LTC6990
PIN FUNCTIONS
(DCB/S6)
V+ (Pin 1/Pin 5): Supply Voltage (2.25V to 5.5V). This
supply must be kept free from noise and ripple. It should
be bypassed directly to the GND pin with a 0.1µF capacitor.
DIV (Pin 2/Pin 4): Programmable Divider and Hi-Z Mode
Input. A V+ referenced A/D converter monitors the DIV
pin voltage (VDIV) to determine a 4-bit result (DIVCODE).
VDIV may be generated by a resistor divider between V+
and GND. Use 1% resistors to ensure an accurate result.
The DIV pin and resistors should be shielded from the
OUT pin or any other traces that have fast edges. Limit
the capacitance on the DIV pin to less than 100pF so that
VDIV settles quickly. The MSB of DIVCODE (Hi-Z) determines the behavior of the output when OE is driven low.
If Hi-Z = 0 the output is pulled low when disabled. If Hi-Z
= 1 the output is placed in a high impedance condition
when disabled.
SET (Pin 3/Pin 3): Frequency-Setting Input. The voltage
on the SET pin (VSET) is regulated to 1V above GND. The
amount of current sourced from the SET pin (ISET) programs the master oscillator frequency. The ISET current
range is 1.25µA to 40µA. The output oscillation will stop
if ISET drops below approximately 500nA. A resistor connected between SET and GND is the most accurate way to
set the frequency. For best performance, use a precision
metal or thin film resistor of 0.5% or better tolerance
and 50ppm/°C or better temperature coefficient. For lower
accuracy applications an inexpensive 1% thick film resistor may be used.
8
Limit the capacitance on the SET pin to less than 10pF
to minimize jitter and ensure stability. Capacitance less
than 100pF maintains the stability of the feedback circuit
regulating the VSET voltage.
V+
OE
OUT
LTC6990
GND
SET
RSET
V+
V+
C1
0.1µF
R1
DIV
6990 PF
R2
OE (Pin 4/Pin 1): Output Enable. Drive high to enable the
output driver (Pin 6). Driving OE low disables the output
asynchronously, so that the output is immediately forced
low (Hi-Z = 0) or floated (Hi-Z = 1). When enabled, the
output may temporarily remain low to synchronize with
the internal oscillator in order to eliminate pulse slivers.
GND (Pin 5/Pin 2): Ground. Tie to a low inductance
ground plane for best performance.
OUT (Pin 6/Pin 6): Oscillator Output. The OUT pin swings
from GND to V+ with an output resistance of approximately
30Ω. When driving an LED or other low-impedance load
a series output resistor should be used to limit source/
sink current to 20mA.
Rev. D
For more information www.analog.com
LTC6990
BLOCK DIAGRAM
(S6 Package Pin Numbers Shown)
5
R1
DIV
4
V+
1
4-BIT A/D
CONVERTER
OE
Hi-Z BIT
DIGITAL
FILTER
R2
Hi-Z WHEN
DISABLED
MASTER OSCILLATOR
t MASTER =
1µs VSET
•
50kΩ ISET
MCLK
PROGRAMMABLE DIVIDER
÷1, 2, 4, 8, 16, 32, 64, 128
OUT
6
tOUT
Hi-Z OUTPUT
UNTIL SETTLED
HALT OSCILLATOR
IF ISET < 500nA
ISET
+
–
POR
+
–
1V
2
VSET = 1V
3
GND
SET
6990 BD
RSET
Rev. D
For more information www.analog.com
9
LTC6990
OPERATION
The LTC6990 is built around a master oscillator with a
1MHz maximum frequency. The oscillator is controlled
by the SET pin current (ISET) and voltage (VSET), with a
1MHz • 50k conversion factor that is accurate to ±0.8%
under typical conditions.
I
= 1MHz • 50k • SET
t MASTER
VSET
1
f MASTER =
1
t MASTER
=
The DIV pin connects to an internal, V+ referenced 4-bit
A/D converter that monitors the DIV pin voltage (VDIV) to
determine the DIVCODE value. DIVCODE programs two
settings on the LTC6990:
1. DIVCODE determines the output frequency divider setting, NDIV.
A feedback loop maintains VSET at 1V ±30mV, leaving ISET
as the primary means of controlling the output frequency.
The simplest way to generate ISET is to connect a resistor
(RSET) between SET and GND, such that ISET = VSET/RSET.
The master oscillator equation reduces to:
f MASTER =
DIVCODE
2. DIVCODE determines the state of the output when disabled, via the Hi-Z bit.
VDIV may be generated by a resistor divider between V+
and GND as shown in Figure 1.
1MHz • 50k
2.25V TO 5.5V
R SET
V+
LTC6990
From this equation it is clear that VSET drift will not affect
the output frequency when using a single program resistor (RSET). Error sources are limited to RSET tolerance and
the inherent frequency accuracy ∆fOUT of the LTC6990.
RSET values between 50k and 800k (equivalent to ISET
between 1.25µA and 20µA) produce the best results,
although RSET may be reduced to 25k (ISET = 40µA) with
reduced accuracy.
R1
DIV
R2
GND
6990 F01
Figure 1. Simple Technique for Setting DIVCODE
The LTC6990 includes a programmable frequency divider
which can further divide the frequency by 1, 2, 4, 8, 16,
32, 64 or 128 before driving the OUT pin. The divider ratio
NDIV is set by a resistor divider attached to the DIV pin.
fOUT =
1
t OUT
=
1MHz • 50k ISET
•
NDIV
VSET
With RSET in place of VSET /ISET the equation reduces to:
fOUT =
10
1
t OUT
=
1MHz • 50k
NDIV • R SET
Rev. D
For more information www.analog.com
LTC6990
OPERATION
Table 1. DIVCODE Programming
DIVCODE
Hi-Z
NDIV
Recommended fOUT
R1 (k)
R2 (k)
VDIV /V+
0
0
1
62.5kHz to 1MHz
Open
Short
≤ 0.03125 ±0.015
1
0
2
31.25kHz to 500kHz
976
102
0.09375 ±0.015
2
0
4
15.63kHz to 250kHz
976
182
0.15625 ±0.015
3
0
8
7.813kHz to 125kHz
1000
280
0.21875 ±0.015
4
0
16
3.906kHz to 62.5kHz
1000
392
0.28125 ±0.015
5
0
32
1.953kHz to 31.25kHz
1000
523
0.34375 ±0.015
6
0
64
976.6Hz to 15.63kHz
1000
681
0.40625 ±0.015
7
0
128
488.3Hz to 7.813kHz
1000
887
0.46875 ±0.015
8
1
128
488.3Hz to 7.813kHz
887
1000
0.53125 ±0.015
9
1
64
976.6Hz to 15.63kHz
681
1000
0.59375 ±0.015
10
1
32
1.953kHz to 31.25kHz
523
1000
0.65625 ±0.015
11
1
16
3.906kHz to 62.5kHz
392
1000
0.71875 ±0.015
12
1
8
7.813kHz to 125kHz
280
1000
0.78125 ±0.015
13
1
4
15.63kHz to 250kHz
182
976
0.84375 ±0.015
14
1
2
31.25kHz to 500kHz
102
976
0.90625 ±0.015
15
1
1
62.5kHz to 1MHz
Short
Open
≥ 0.96875 ±0.015
Table 1 offers recommended 1% resistor values that accurately produce the correct voltage division as well as the
corresponding NDIV and Hi-Z values for the recommended
resistor pairs. Other values may be used as long as:
column in Table 1 shows the ideal ratio of VDIV to the
supply voltage, which can also be calculated as:
VDIV
1. The VDIV /V+ ratio is accurate to ±1.5% (including resistor tolerances and temperature effects)
V
+
=
DIVCODE + 0.5
16
± 1.5%
For example, if the supply is 3.3V and the desired DIVCODE
is 4, VDIV = 0.281 • 3.3V = 928mV ± 50mV.
2. The driving impedance (R1||R2) does not exceed 500kΩ.
Figure 2 illustrates the information in Table 1, showing
that NDIV is symmetric around the DIVCODE midpoint.
If the voltage is generated by other means (i.e. the output
of a DAC) it must track the V+ supply voltage. The last
On start-up, the DIV pin A/D converter must determine
the correct DIVCODE before the output is enabled. If VDIV
Hi-Z BIT = 0
Hi-Z BIT = 1
1000
fOUT (kHz)
0
100
2
10
3
4
11
5
12
13
14
15
10
6
9
7
1
0.1
1
8
RECOMMENDED RANGE
EXTENDED RANGE
0V
0.5• V+
V+
INCREASING VDIV
6990 F02
Figure 2. Frequency Range and Hi-Z Bit vs DIVCODE
Rev. D
For more information www.analog.com
11
LTC6990
OPERATION
is not stable, it will increase the start-up time as the converter waits for a stable result. Therefore, capacitance on
the DIV pin should be minimized so it will settle quickly.
Less than 100pF will not affect performance.
Output Enable
The OE pin controls the state of the LTC6990’s output as
seen on the OUT pin. Pulling the OE pin high enables the
oscillator output. Pulling it low disables the output. When
the output is disabled, it is either held low or placed in
a high impedance state as dictated by the Hi-Z bit value
(determined by the DIVCODE as described earlier). Table 2
summarizes the output control states.
Table 2. Output States
OE Pin
Hi-Z
OUT
1
X
Enabled, Output is Active
0
1
Disabled, Output is Hi-Z
0
0
Disabled, Output is Held Low
Figure 3 illustrates the timing for the OE function when
Hi-Z = 0. When OE is low, the output is disabled and OUT
is held low. Bringing OE high enables the output after a
delay, tENABLE, which synchronizes the enable to eliminate
sliver pulses and guarantee the correct width for the first
pulse. If NDIV = 1 or 2 this delay will be no longer than the
output period, tOUT. If NDIV > 2 the delay is limited to twice
the internal master oscillator period (or 2 • tMASTER).
Forcing OE low will bring OUT low after a propagation
delay, tPD. If the output is high when OE falls, the output
pulse will be truncated.
As shown in Figure 4, setting Hi-Z = 1 places the output in
a high-impedance state when OE = 0. This feature allows
for “wired-OR” connections of multiple devices. Driving
OE high enables the output. The output will usually be
forced low during this time, although it is possible for
OUT to transition directly from high-impedance to a high
output, depending on the timing of the OE transition relative to the internal oscillator. Once high, the first output
pulse will have the correct width (unless truncated by
bringing OE low again).
OE
tPD
tPD
OUT
tENABLE
tOUT
tENABLE
6990 F03
Figure 3. OE Timing Diagram (Hi-Z = 0)
OE
tPD
OUT
tPD
tPD
tPD
Hi-Z
tENABLE
tOUT
tENABLE
6990 F04
Figure 4. OE Timing Diagram (Hi-Z = 1)
12
Rev. D
For more information www.analog.com
LTC6990
OPERATION
Changing DIVCODE After Start-Up
Start-Up Time
Following start-up, the A/D converter will continue monitoring VDIV for changes. Changes to DIVCODE will be
recognized slowly, as the LTC6990 places a priority on
eliminating any “wandering” in the DIVCODE. The typical delay depends on the difference between the old and
new DIVCODE settings and is proportional to the master
oscillator period.
When power is first applied to the LTC6990 the power-on
reset (POR) circuit will initiate the start-up time, tSTART.
The OUT pin is floated (high-impedance) during this time.
The typical value for tSTART ranges from 0.5ms to 8ms
depending on the master oscillator frequency (independent of NDIV):
tDIVCODE = 16 • (∆DIVCODE + 6) • tMASTER
The start-up time may be longer if the supply or DIV
pin voltages are not stable. For this reason, it is recommended to minimize the capacitance on the DIV pin so it
will properly track V+.
A change in DIVCODE will not be recognized until it is
stable, and will not pass through intermediate codes. A
digital filter is used to guarantee the DIVCODE has settled
to a new value before making changes to the output. Then
the output will make a clean (glitchless) transition to the
new divider setting.
t START(TYP) = 500 • tMASTER
576µs
DIV
1V/DIV
V+
1V/DIV
470µs
OUT
1V/DIV
OUT
1V/DIV
V+ = 3.3V
RSET = 200k
100µs/DIV
6990 F05
OUTPUT CONNECTED
TO 1.25V THROUGH 25k
TO SHOW Hi-Z
V+ = 2.5V
DIVCODE = 4
RSET = 50k
Figure 5. DIVCODE Change from 5 to 2
100µs/DIV
6990 F06
Figure 6. Typical Start-Up
Rev. D
For more information www.analog.com
13
LTC6990
APPLICATIONS INFORMATION
OE
Hi-Z
OUT
1/2 tOUT
tSTART
tOUT
6990 F07
Figure 7. Start-Up Timing Diagram (OE = 1, NDIV = 1 or 2, Hi-Z = 0 or 1)
OE
Hi-Z
OUT
tSTART
tMASTER
tOUT
6990 F08
Figure 8. Start-Up Timing Diagram (OE = 1, NDIV ≥ 4, Hi-Z = 0 or 1)
OE
OUT
Hi-Z
tSTART
tENABLE
tOUT
6990 F09
Figure 9. Start-Up Timing Diagram (OE = 0, NDIV = Any, Hi-Z = 0)
OE
tPD
OUT
Hi-Z
tSTART
REMAINS Hi-Z tENABLE
UNTIL OE = 1
tOUT
6990 F10
Figure 10. Start-Up Timing Diagram (OE = 0, NDIV = Any, Hi-Z = 1)
14
Rev. D
For more information www.analog.com
LTC6990
APPLICATIONS INFORMATION
Start-Up Behavior
Step 2: Calculate and Select RSET
When first powered up, the output is high impedance. If
the output is enabled (OE = 1) at the end of the start-up
time, the output will go low for one tMASTER cycle (or half
a tOUT cycle if NDIV < 4) before the first rising edge. If the
output is disabled (OE = 0) at the end of the start-up time,
the output will drop to a low output if the Hi-Z bit = 0, or
simply remain floating if Hi-Z = 1.
The final step is to calculate the correct value for RSET
using the following equation.
Basic Fixed Frequency Operation
Example: Design a 20kHz Oscillator with Minimum
Power Consumption
The simplest and most accurate method to program the
LTC6990 for fixed frequency operation is to use a single resistor, RSET, between the SET and GND pins. The
design procedure is a simple two step process. First select
the NDIV value and then calculate the value for the RSET
resistor.
Alternatively, Analog Devices offers the easy to use
TimerBlox Designer tool to quickly design any LTC6990
based circuit. Use the free TimerBlox LTC6990: Voltage
Controlled Oscillator Web-Based Design Tool.
Step 1: Selecting the NDIV Frequency Divider Value
As explained earlier, the voltage on the DIV pin sets the
DIVCODE which determines both the Hi-Z bit and the
NDIV value. For a given output frequency, NDIV should be
selected to be within the following range.
62.5kHz
fOUT
≤ NDIV ≤
1MHz
fOUT
(1a)
To minimize supply current, choose the lowest NDIV value
(generally recommended). For faster start-up or decreased
jitter, choose a higher NDIV setting. Alternatively, use
Table 1 as a guide to select the best NDIV value for the
given application. After choosing the value for NDIV, use
Table 1 to select the proper resistor divider or VDIV/V+
ratio to apply to the DIV pin.
R SET =
1MHz • 50k
NDIV • fOUT
(1b)
Select the standard resistor value closest to the calculated
value.
Step 1: Selecting the NDIV Frequency Divider Value
First, choose an NDIV value that meets the requirements
of Equation (1a).
3.125 ≤ NDIV ≤ 50
Potential settings for NDIV include 4, 8, 16, and 32. NDIV
= 4 is the best choice, as it minimizes supply current by
using a large RSET resistor. Using Table 1, choose the R1
and R2 values to program DIVCODE to either 2 or 13,
depending on the desired behavior when the output is
disabled.
Step 2: Select RSET
Calculate the correct value for RSET using Equation (1b).
R SET =
1MHz • 50k
4 • 20kHz
= 625k
Since 625k is not available as a standard 1% resistor,
substitute 619k if a 0.97% frequency shift is acceptable.
Otherwise, select a parallel or series pair of resistors such
as 309k and 316k to attain a more precise resistance.
Rev. D
For more information www.analog.com
15
LTC6990
APPLICATIONS INFORMATION
Frequency Modulated Operation (Voltage-Controlled
Oscillator)
Operating the LTC6990 as a voltage-controlled oscillator
in its simplest form is achieved with one additional resistor. As shown in Figure 11, voltage VCTRL sources/sinks
a current through RVCO to vary the ISET current, which
in turn modulates the output frequency as described in
Equation (2).
fOUT =
1MHz • 50k ⎛ R VCO VCTRL ⎞
• 1+
–
NDIV •R VCO ⎜⎝ RSET VSET ⎟⎠
(2)
V+
OE
V+
LTC6990
VCTRL
RVCO
V+
SET
RSET
62.5kHz
C1
0.1µF
R1
(3a)
fOUT(MAX)
KVCO and f(0V) define the VCO’s transfer function and simplify the calculation of the the RVCO and RSET resistors.
Calculate these parameters using the following equations.
DIV
R2
6990 F08
Figure 11. Voltage Controlled Oscillator
Equation (2) can be re-written as shown below, where
f(0V) is the output frequency when VCTRL = 0V, and KVCO
is the frequency gain. Note that the gain is negative (the
output frequency decreases as VCTRL increases).
fOUT = f(0V) – K VCO • VCTRL
1MHz • 50k
NDIV • (R SET R VCO )
1MHz • 50k
K VCO =
NDIV • VSET • R VCO
1MHz
The 16:1 frequency range of the master oscillator and
the 2:1 divider step-size provides several overlapping frequency spans to guarantee that any 8:1 modulation range
can be covered by a single NDIV setting. RVCO allows the
gain to be tailored to the application, mapping the VCTRL
voltage range to the modulation range.
f(0V) =
fOUT(MIN)
≤ NDIV ≤
Step 2: Calculate KVCO and f(0V)
OUT
GND
fOUT, choose a value for NDIV that meets the following
conditions
K VCO =
fOUT(MAX) – fOUT(MIN)
VCTRL(MAX) – VCTRL(MIN)
f(0V) = fOUT(MAX) + KVCO • VCTRL(MIN)
(3b)
(3c)
KVCO and f(0V) are not device settings or resistor values
themselves. However, beyond their utility for the resistor
calculations, these parameters provide a useful and intuitive way to look at the VCO application. The f(0V) parameter is the output frequency when VCTRL is at 0V. Viewed
another way, it is the fixed output frequency when the
RVCO and RSET resistors are in parallel. KVCO is actually
the frequency gain of the circuit.
With KVCO and f(0V) determined, the RVCO and RSET values
can now be calculated.
Step 3: Calculate and Select RVCO
The design procedure for a VCO is a simple four step
process. First select the NDIV value. Then calculate the
intermediate values KVCO and f(0V). Next, calculate and
select the RVCO resistor. Finally calculate and select the
RSET resistor.
Step 1: Select the NDIV Frequency Divider Value
The next step is to calculate the correct value for RVCO
using the following equation.
R VCO =
1MHz • 50k
NDIV • VSET • K VCO
(3d)
Select the standard resistor value closest to the calculated
value.
For best accuracy, the master oscillator frequency should
fall between 62.5kHz and 1MHz. Since fMASTER = NDIV •
16
Rev. D
For more information www.analog.com
LTC6990
APPLICATIONS INFORMATION
The final step is to calculate the correct value for RSET
using the following equation:
R SET =
(
1MHz • 50k
NDIV • f(0V) – VSET • K VCO
)
(3e)
Select the standard resistor value closest to the calculated
value.
Some applications require combinations of fOUT(MIN),
fOUT(MAX), VCTRL(MIN) and VCTRL(MAX) that are not achievable. These applications result in unrealistic or unrealizable (e.g. negative value) resistors. These applications
will require preconditioning of the VCTRL signal via range
scaling and/or level shifting to place the VCTRL into a range
that yields realistic resistor values.
Frequency Error in VCO Applications Due to VSET Error
As stated earlier, f(0V) represents the frequency for VCTRL
= 0V, which is the same value as would be generated by
a single resistor between SET and GND with a value of
RSET || RVCO . Therefore, f(0V) is not affected by error or
drift in VSET (i.e. ΔVSET adds no frequency error when
VCTRL = 0V).
The accuracy of KVCO does depend on VSET because
the output frequency is controlled by the ratio of VCTRL
to VSET. The frequency error (in Hertz) due to ΔVSET is
approximated by:
∆V
∆fOUT ≅ K VCO • VCTRL • SET
VSET
frequency range applications (high KVCO) can have frequency errors greater than ±50% at the highest VCTRL
voltage (lowest fOUT). For this reason the simple, two
resistor VCO circuit must be used with caution for applications where the frequency range is greater than 4:1.
Restricting the range to 4:1 typically keeps the frequency
error due to VSET variation below 10%.
For wide frequency range applications, the non-inverting VCO circuit shown in Figure 13 is preferred because
the maximum frequency error occurs when the frequency is highest, keeping the relative error (in percent)
much smaller.
100
80
fOUT (kHz)
Step 4: Calculate and Select RSET
60
40
20
0
1
3
2
VCTRL (V)
4
6990 F12
Figure 12. VCO Transfer Function
Example: Design a VCO with the Following Parameters
fOUT(MAX) = 100kHz at VCTRL(MIN) = 1V
As the equation indicates, the potential for error in output
frequency due to VSET error increases with KVCO and is
at its largest when VCTRL is at its maximum. Recall that
when VCTRL is at its maximum, the output frequency is
at its minimum. With the maximum absolute frequency
error (in Hertz) occurring at the lowest output frequency,
the relative frequency error (in percent) can be significant.
VSET is nominally 1.0V with a maximum error of ±30mV
for at most a ±3% error term. However, this ±3% potential
error term is multiplied by both VCTRL and KVCO. Wide
fOUT(MIN) = 10kHz at VCTRL(MAX) = 4V
Step 1: Select the NDIV Value
First, choose an NDIV that meets the requirements of
Equation (3a).
6.25 ≤ NDIV ≤ 10
The application’s desired frequency range is 10:1, which
isn’t always possible. However, in this case NDIV = 8 meets
both requirements of Equation (3).
Rev. D
For more information www.analog.com
17
LTC6990
APPLICATIONS INFORMATION
Step 2: Calculate KVCO and f(0V)
Next, calculate the intermediate values KVCO and f(0V)
using Equations (3b) and (3c).
K VCO =
100kHz −10kHz
= 30kHz/V
4V −1V
f(0V) = 100kHz + 30kHz/V •1V = 130kHz
Step 3: Calculate and Select RVCO
The next step is to use Equation (3d) to calculate the correct value for RVCO.
R VCO =
1MHz • 50k
8 • 1V • 30kHz/V
Step 4: Calculate and Select RSET
The final step is to calculate the correct value for RSET
using Equation (3e).
Depending on the application’s requirements, the noninverting VCO circuit in Figure 13 may be preferred for
this wide of a frequency variation as its maximum inaccuracy due to VSET error is only ±9% and can be reduced
to only ±3% with a small change to the voltage tuning
range specification.
Reducing VSET Error Effects in VCO Applications
= 208.333k
Select RVCO = 210k.
RSET =
In this design example, with its wide 10:1 frequency
range, the potential output frequency error due to VSET
error alone ranges from less than ±1% when VCTRL is at
its minimum up to ±36% when VCTRL is at its maximum.
This error must be accounted for in the system design.
1MHz • 50k
= 62.5k
8 • (130kHz −1V • 30kHz/V )
Select RSET = 61.9k
Figure 13 shows a VCO that reduces the effect of ΔVSET
by adding an op-amp to make VCTRL dependent on VSET.
This circuit also has a positive transfer function (the output frequency increases as VIN increases). Furthermore,
for positive VIN voltages, this circuit places the greatest
absolute frequency error at the highest output frequency.
Compared to the simple VCO circuit of Figure 11, the
absolute frequency error is unchanged. However, with the
maximum absolute frequency error (in Hertz) now occurring at the highest output frequency, the relative frequency
error (in percent) is greatly improved.
10kHz TO 100kHz
fOUT
3V
OE
OUT
LTC6990
VSET
GND
V+
SET
DIV
3V
+
0.4V TO 4V
VIN
R3
100k
1/2
LTC6078
C1
0.1µF
6990 F13
RVCO
VCTRL 75k
–
RSET
249k
R4
30.1k
C4
33pF
3V
fOUT =
IF
R1
1M
DIVCODE = 3
(NDIV = 8, Hi-Z = 0)
R2
280k
& R4 ,
1MHz • 50k! ) R VCO # VIN
•+
+
"1 • .
NDIV •R VCO * RSET %$ VSET (' R3 -
R4 R VCO
=
, THE EQUATION REDUCES TO:
R3 RSET
fOUT =
1MHz • 50k! VIN
•
= VIN • 25kHz/V
NDIV •RSET VSET
Figure 13. VCO with Reduced ∆VSET Sensitivity
18
Rev. D
For more information www.analog.com
LTC6990
APPLICATIONS INFORMATION
Additionally, by choosing the VCO’s specifications
shrewdly, the frequency error (in percent) due to VSET
variation is reduced to ΔVSET/VSET = ±3%. To realize this
improvement, the design must abide by three conditions. First, the VIN voltage must be positive throughout
the range. Second, choose VMAX /VMIN ≥ fMAX /fMIN. Last,
choose RVCO /RSET ≥ R4/R3.
ISET Extremes (Master Oscillator Frequency Extremes)
Figure 13 shows a design similar to the previous design
example where the VMIN voltage is now specified to be
0.4V. This satisfies the VMAX /VMIN ≥ fMAX /fMIN condition
and the design assures that the output frequency error
due to VSET variation is only ±3%.
The LTC6990 is designed to function normally for ISET
as low as 1.25µA. At approximately 500nA, the oscillator
output will be frozen in its current state. For NDIV = 1 or 2,
OUT will halt in a low state. But for larger divider ratios,
it could halt in a high or low state. This avoids introducing short pulses while modulating a very low frequency
output. Note that the output will not be disabled as when
OE is low (e.g. the output will not enter a high impedance
state if Hi-Z = 1).
Eliminating VSET Error Effects with DAC Frequency
Control
Many DACs allow for the use of an external reference.
If such a DAC is used to provide the VCTRL voltage, the
VSET error is eliminated by buffering VSET and using it as
the DAC’s reference voltage, as shown in Figure 14. The
DAC’s output voltage now tracks any VSET variation and
eliminates it as an error source. The SET pin cannot be
tied directly to the reference input of the DAC because
the current drawn by the DAC’s REF input would affect
the frequency.
Pushing ISET outside of the recommended 1.25µA to 20µA
range forces the master oscillator to operate outside of
the 62.5kHz to 1MHz range in which it is most accurate.
The oscillator will still function with reduced accuracy
in its extended range (see the Electrical Characteristics
section).
At the other extreme, the master oscillator frequency can
reach 2MHz for ISET = 40μA (RSET = 25k). It is not recommended to operate the master oscillator beyond 2MHz
because the accuracy of the DIV pin ADC will suffer.
OE
OUT
V+
LTC6990
GND
V+
SET
DIV
V+
+
1/2
LTC6078
6990 F14
C1
0.1µF
R1
R2
–
V+
DIN
µP
CLK
CS/LD
VCC
fOUT =
REF
LTC1659
GND
VOUT
RVCO
1MHz • 50k! # R VCO DIN &
• 1+
"
NDIV •R VCO %$ RSET 4096 ('
DIN = 0 to 4095
RSET
Figure 14. Digitally Controlled Oscillator with VSET Variation Eliminated
Rev. D
For more information www.analog.com
19
LTC6990
APPLICATIONS INFORMATION
Modulation Bandwidth and Settling Time
Power Supply Current
The LTC6990 will respond to changes in ISET up to a –3dB
bandwidth of 0.4 • fOUT (see Figure 15). This makes it easy
to stabilize a feedback loop around the LTC6990, since it
does not introduce a low-frequency pole.
The power supply current varies with frequency, supply
voltage and output loading. It can be estimated under any
condition using the following equation:
Settling time depends on the master oscillator frequency.
Following a 2x or 0.5x step change in ISET, the output
frequency takes approximately six master clock cycles
(6 • tMASTER) to settle to within 1% of the final value. An
example is shown in Figure 16.
∆fOUT (fMOD)/∆fOUT(DC) (dB)
0
V+
V+
+
+1.75 •ISET + 50µA
480kΩ 2 •RLOAD
VCTRL
2V/DIV
–3dB AT 0.4•fOUT
OUT
2V/DIV
–20
–30
fOUT
50kHz/DIV
RSET = 200k
RVCO = 464k
DIVCODE = 4(÷16)
–40
0.1
1
fMOD /fOUT (Hz/Hz)
10
6990 F15
Figure 15. Modulation Frequency Response
20
+
The equation is also valid for OE = 0 (output disabled),
with fOUT = 0Hz.
VCTRL = 0.536V + 0.278V
• SIN(2π•fMOD •t)
fOUT =18.75kHz ±10%
–10
IS(TYP) ≈ V + • fMASTER • 7pF + V + • f OUT •(13pF +CLOAD )
10µs/DIV
V+ = 3.3V, DIVCODE = 0
RSET = 200k, RVCO = 464k
fOUT = 175kHz AND 350kHz
6990 F16
Figure 16. Settling Time
Rev. D
For more information www.analog.com
LTC6990
APPLICATIONS INFORMATION
SUPPLY BYPASSING AND PCB LAYOUT GUIDELINES
The LTC6990 is a 2.2% accurate silicon oscillator when
used in the appropriate manner. The part is simple to use
and by following a few rules, the expected performance
is easily achieved. The most important use issues involve
adequate supply bypassing and proper PCB layout.
Figure 17 shows example PCB layouts for both the SOT-23
and DCB packages using 0603 sized passive components.
The layouts assume a two layer board with a ground plane
layer beneath and around the LTC6990. These layouts are
a guide and need not be followed exactly.
1. Connect the bypass capacitor, C1, directly to the V+ and
GND pins using a low inductance path. The connection
from C1 to the V+ pin is easily done directly on the top
layer. For the DCB package, C1’s connection to GND
is also simply done on the top layer. For the SOT-23,
OUT can be routed through the C1 pads to allow a good
C1 GND connection. If the PCB design rules do not
allow that, C1’s GND connection can be accomplished
through multiple vias to the ground plane. Multiple
vias for both the GND pin connection to the ground
OE
plane and the C1 connection to the ground plane are
recommended to minimize the inductance. Capacitor
C1 should be a 0.1µF ceramic capacitor.
2. Place all passive components on the top side of the
board. This minimizes trace inductance.
3. Place RSET as close as possible to the SET pin and
make a direct, short connection. The SET pin is a current summing node and currents injected into this pin
directly modulate the operating frequency. Having a
short connection minimizes the exposure to signal
pickup.
4. Connect RSET directly to the GND pin. Using a long path
or vias to the ground plane will not have a significant
affect on accuracy, but the direct, short connection is
recommended and easy to apply.
5. Use a ground trace to shield the SET pin. This provides
another layer of protection from radiated signals.
6. Place R1 and R2 close to the DIV pin. A direct, short
connection to the DIV pin minimizes the external signal
coupling.
OUT
LTC6990
GND
SET
V+
V+
C1
0.1µF
R1
DIV
RSET
R2
V+
R1
R2
V+
C1
C1
V+
OUT
OE
OUT
DIV
GND
GND
V+
SET
OE
SET
DIV
R1
RSET
RSET
DCB PACKAGE
R2
TSOT-23 PACKAGE
6990 F17
Figure 17. Supply Bypassing and PCB Layout
Rev. D
For more information www.analog.com
21
LTC6990
TYPICAL APPLICATIONS
Programming NDIV Using an 8-Bit DAC
OE
DIVCODE
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
OUT
LTC6990
2.25V TO 5.5V
GND
V+
SET
DIV
C1
0.1µF
C2
0.1µF
RSET
619k
VCC
SDI
VOUT LTC2630-LZ8 SCK
GND
µP
CS/LD
DAC CODE
0
24
40
56
72
88
104
120
136
152
168
184
200
216
232
255
6990 TA02
Full Range VCO with Any NDIV Setting (fMAX to fMIN for VIN = 0V to VSET)
5V
RVCO2
26.1k
OE
OUT
LTC6990
VIN
0V TO 1V
RVCO1
26.1k
5V
V+
GND
D1
IN4148
–
LT1490
SET
+
C1
0.1µF
5V
R1
DIV
6990 TA03
R2
RSET
826k
Full Range VCO with Any NDIV Setting (Positive Frequency Control, fMIN to fMAX for VIN = 0V to VSET
5V
R4
10k
VIN
0V TO 1V
R3
10k
OE
5V
–
LT1490
OUT
LTC6990
RVCO
53.6k
+
GND
V+
SET
DIV
6990 TA04
RSET1
412k
C1
0.1µF
5V
R1
R2
RSET2
412k
22
Rev. D
For more information www.analog.com
LTC6990
TYPICAL APPLICATIONS
Speaker Alarm. Modulate Tone with RVCO within 500Hz to 8kHz Span
5V
8Ω
IN4004
5V
20k
OE
2N2222
OUT
LTC6990
RAMP
GND
V+
SET
DIV
5V
1M
RVCO
STEP
50k
6990 TA05
97.6k
887k
Overvoltage Detector/Alarm. Direct Drive of Piezo Alarm
24V
RA
787k
RB
10.7k
400mV
5V
+
100k
LT6703-3
OE
–
OUT
LTC6990
GND
V
+
5V
1M
⎛ R ⎞
V ALARM = 400mV ⎜ 1+ A ⎟ = 30V
⎝ RB ⎠
SET
392k
PIEZO ALARM
4kHz
MURATA
PKM29-3A0
DIV
6990 TA06
523k
Rev. D
For more information www.analog.com
23
LTC6990
TYPICAL APPLICATIONS
Direct Piezo Alarm Driver. Adjust Frequency for Maximum Alarm Sound Pressure
(Maximum Annoyance for Best Effect)
5V
10k
ON
OE
OFF
OUT
LTC6990
GND
V+
PIEZO ALARM
MURATA
PKM29-340
f = 4kHz
5V
1M
SET
DIV
6990 TA07
392k
523k
Isolated V → F Converter. VIN Provided by Isolated Measurement Circuit.
5µs Rise/Fall Time of Isolator Limits fMAX to 60kHz
3.3V
5V
365Ω
OE
MOC207M
OUT
LTC6990
GND
VIN
0V TO 5V
5V
1M
75k
SET
157k
24
V+
DIV
6990 TA08
412Ω
fOUT
523k
Rev. D
For more information www.analog.com
LTC6990
TYPICAL APPLICATIONS
Quadrature Sine Wave Oscillator. Voltage Controlled Frequency Range
from ~5Hz to ~20kHz with 1VP-P Constant Output Amplitude
SINE
1.18VREF
COSINE
51.1k
5.11k
INV1
124k
3
2 N
4 S1
1 BP
14 LP
5V
–
LTC1059*
–
+
+
–
8 CLOCK
5V
5 SA 11 AGND
9 50/100
10k
LT1004-2.5V
VCC
OUT
OUT
2k
GND
R1
1M
DIV
SET
R2
280k
RVCO
267k
RSET
49.9k
FREQ
ADJ
6990 TA09
+
1.18VREF
V+
5V
1M
LTC1440
V–
OE
LTC6990
–
5V
2.5V FOR 5Hz TO 10kHz
5V FOR 10Hz TO 20kHz
2.5V
*1/2 OF AN LTC1060 FILTER CAN
BE USED IN PLACE OF THE LTC1059
HYST
0.1µF
4.12k
1M
Temperature to Frequency Converter.
3% Linearity from –20°C (fOUT ≈ 20kHz) to 75°C (fOUT ≈ 25kHz)
5V
OE
OUT
fOUT
LTC6990
60.4k
22k AT 25°C
B = 3964
21.5k
GND
V+
SET
DIV
5V
1M
6990 TA10
523k
+
THERMISTOR: VISHAY NTHS120601N2202J
Rev. D
For more information www.analog.com
25
LTC6990
TYPICAL APPLICATIONS
Full Range Temperature to Frequency Converter. 16kHz to 1kHz from –20°C to 80°C
5V
OE
10k
5V
–
22k AT 25°C
B = 3964
+
10k
OUT
fOUT
LTC6990
V+
SET
DIV
5V
1M
100k
LT1490
GND
6990 TA11
+
681k
26k
26k
THERMISTOR: VISHAY NTHS120601N2202J
Light to Frequency Converter. fOUT ≈ –1.4kHz per Microampere of Photo Diode Current, IPD
1000pF
5V
OE
24.9k
IPD
–
SFH213
26
+
OUT
fOUT
LTC6990
5V
LT1677
222k
GND
V+
SET
DIV
5V
187k
619k
6990 TA12
1M
Rev. D
For more information www.analog.com
LTC6990
PACKAGE DESCRIPTION
DCB Package
6-Lead Plastic DFN (2mm × 3mm)
(Reference LTC DWG # 05-08-1715 Rev A)
0.70 ±0.05
3.55 ±0.05
1.65 ±0.05
(2 SIDES)
2.15 ±0.05
PACKAGE
OUTLINE
0.25 ±0.05
0.50 BSC
1.35 ±0.05
(2 SIDES)
RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS
R = 0.115
TYP
2.00 ±0.10
(2 SIDES)
R = 0.05
TYP
3.00 ±0.10
(2 SIDES)
0.40 ±0.10
4
6
1.65 ±0.10
(2 SIDES)
PIN 1 NOTCH
R0.20 OR 0.25
× 45° CHAMFER
PIN 1 BAR
TOP MARK
(SEE NOTE 6)
3
0.200 REF
0.75 ±0.05
1
(DCB6) DFN 0405
0.25 ±0.05
0.50 BSC
1.35 ±0.10
(2 SIDES)
0.00 – 0.05
BOTTOM VIEW—EXPOSED PAD
NOTE:
1. DRAWING TO BE MADE A JEDEC PACKAGE OUTLINE M0-229 VARIATION OF (TBD)
2. DRAWING NOT TO SCALE
3. ALL DIMENSIONS ARE IN MILLIMETERS
4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE
MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE
5. EXPOSED PAD SHALL BE SOLDER PLATED
6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON THE
TOP AND BOTTOM OF PACKAGE
Rev. D
For more information www.analog.com
27
LTC6990
PACKAGE DESCRIPTION
S6 Package
6-Lead Plastic TSOT-23
(Reference LTC DWG # 05-08-1636)
0.62
MAX
2.90 BSC
(NOTE 4)
0.95
REF
1.22 REF
3.85 MAX 2.62 REF
1.4 MIN
2.80 BSC
1.50 – 1.75
(NOTE 4)
PIN ONE ID
RECOMMENDED SOLDER PAD LAYOUT
PER IPC CALCULATOR
0.30 – 0.45
6 PLCS (NOTE 3)
0.95 BSC
0.80 – 0.90
0.20 BSC
DATUM ‘A’
0.30 – 0.50 REF
0.09 – 0.20
(NOTE 3)
NOTE:
1. DIMENSIONS ARE IN MILLIMETERS
2. DRAWING NOT TO SCALE
3. DIMENSIONS ARE INCLUSIVE OF PLATING
4. DIMENSIONS ARE EXCLUSIVE OF MOLD FLASH AND METAL BURR
5. MOLD FLASH SHALL NOT EXCEED 0.254mm
6. JEDEC PACKAGE REFERENCE IS MO-193
28
0.01 – 0.10
1.00 MAX
1.90 BSC
S6 TSOT-23 0302
Rev. D
For more information www.analog.com
LTC6990
REVISION HISTORY
REV
DATE
DESCRIPTION
PAGE NUMBER
A
7/11
Updated Features, Description, Pin Configuration, and Order Information sections
1, 2
Added additional information to ∆fOUT/∆V+ and included Note 11 in Electrical Characteristics section
3, 4
Added Typical Frequency Error vs Time curve to Typical Performance Characteristics section
7
Modified drawing in SET pin description in Pin Functions
8
Added text to Basic Fixed Frequency Operation paragraph in Applications Information section
15
Updated Related Parts list
30
B
01/12
Added MP-grade
1, 2, 4
C
02/14
Web links added
1-30
D
01/20
Schematic edits to Quadrature Sine Wave Oscillator circuit
25
Edits to description of LTC6906 and LTC6907 (Related Parts)
30
Added AEC-Q100 Qualified Note to Front Page
1
Added W-Grade Order Information
2
Rev. D
Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog
Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications
subject to change without notice. No license For
is granted
implication or
otherwise under any patent or patent rights of Analog Devices.
more by
information
www.analog.com
29
LTC6990
TYPICAL APPLICATION
Ultrasonic Frequency Sweep Generator
fOUT = 500kHz TO 31.25kHz
OE
OE
OUT
LTC6990
GND
SET
RSET1
49.9k
74HC125
CSET
0.022µF
RSET2
750k
V+
C1
0.1µF
2.25V TO 5.5V
R1
976k
DIV
6990 TA13
R2
102k
SWEEPS FROM 500kHz to 31.25kHz IN A
FEW MILLISECONDS (CONTROLLED BY CSET).
RELATED PARTS
PART NUMBER
DESCRIPTION
COMMENTS
LTC1799
1MHz to 33MHz ThinSOT Silicon Oscillator
Wide Frequency Range
LTC6900
1MHz to 20MHz ThinSOT Silicon Oscillator
Low Power, Wide Frequency Range
LTC6906
10kHz to 1MHz ThinSOT Silicon Oscillator
Micropower, ISUPPLY = 12µA at 100kHz
LTC6907
40kHz to 4MHz ThinSOT Silicon Oscillator
Micropower, ISUPPLY = 35µA at 400kHz
LTC6930
Fixed Frequency Oscillator, 32.768kHz to 8.192MHz
0.09% Accuracy, 110µs Start-Up Time, 105µA at 32kHz
LTC6991
TimerBlox, Very Low Frequency Clock with Reset
Cycle Time from 2ms to 9.5 Hours, No Caps, 2.2% Accurate
LTC6992
TimerBlox, Voltage-Controlled Pulse Width Modulator
(PWM)
Simple PWM with Wide Frequency Range
LTC6993
TimerBlox, Monostable Pulse Generator
Resistor Set Pulse Width from 1µs to 34sec, No Caps, 3% Accurate
LTC6994
TimerBlox, Delay Block/Debouncer
Resistor Set Delay from 1µs to 34sec, No Caps Required, 3% Accurate
30
Rev. D
01/20
www.analog.com
For more information www.analog.com
ANALOG DEVICES, INC. 2010-2020