LTC7815
Low IQ, 2.25MHz,
Triple Output, Buck/Buck/Boost
Synchronous Controller
DESCRIPTION
FEATURES
Dual Buck Plus Single Boost Synchronous Controllers
n Wide Bias Input Voltage Range: 4.5V to 38V
n Outputs Remain in Regulation Through Cold Crank
Down to a 2.5V Input Supply Voltage
n Buck Output Voltage Range: 0.8V ≤ V
OUT ≤ 24V
n Boost Output Voltage Up to 60V
n Low Operating I : 28μA (One Channel On)
Q
n R
SENSE or DCR Current Sensing
n 100% Duty Cycle for Boost Synchronous MOSFET
Even in Burst Mode® Operation
n Phase-Lockable Frequency (320kHz to 2.25MHz)
n Programmable Fixed Frequency (320kHz to 2.25MHz)
n Very Low Buck Dropout Operation: 98% Duty Cycle
n Small 38-Lead 5mm × 7mm QFN Package
n
APPLICATIONS
n
n
n
n
Automotive Always-On and Start-Stop Systems
Battery Operated Digital Devices
Distributed DC Power Systems
Multioutput Buck-Boost Applications
The LTC®7815 is a high performance triple output (buck/
buck/boost) synchronous DC/DC switching regulator controller that drives all N-channel power MOSFET stages.
Constant frequency current mode architecture allows a
phase-lockable switching frequency of up to 2.25MHz.
The LTC7815 operates from a wide 4.5V to 38V input
supply range. When biased from the output of the boost
converter or another auxiliary supply, the LTC7815 can
operate from an input supply as low as 2.5V after start-up.
The 28μA no-load quiescent current extends operating
runtime in battery powered systems. OPTI-LOOP compensation allows the transient response to be optimized
over a wide range of output capacitance and ESR values.
The LTC7815 features a precision 0.8V reference for the
bucks, 1.2V reference for the boost and a power good
output indicator. The PLLIN/MODE pin selects among
Burst Mode operation, pulse-skipping mode, or continuous inductor current mode at light loads.
All registered trademarks and trademarks are the property of their respective owners. Protected
by U.S. Patents including 5481178, 5705919, 5929620, 6144194, 6177787, 6580258.
TYPICAL APPLICATION
VOUT3
REGULATED AT 10V WHEN VIN < 10V
FOLLOWS VIN WHEN VIN > 10V
+
68µF
10µF
×5
499k
VFB3
Efficiency and Power Loss vs
Output Current
VBIAS
3mΩ
+
0.16µH
220µF
TG3
SW1
SW3
BG1
LTC7815
BG3
SENSE1+
SENSE1–
VFB1
SENSE3–
SENSE3+
INTVCC
10µF
×2
68.1k
4.7µF
EXTVCC
BOOST1, 2, 3
SW1, 2, 3
0.1µF
TG2
SW2
BG2
ITH1, 2, 3
0.1µF
TRACK/SS1, 2
SS3
PGND
357k
COUT1
47µF
×2
80
1k
70
100
60
50
10
40
30
f = 2.1MHz
20
0.33µH
3mΩ
210k
VOUT2
3.3V
10A
0
0.0001
1
Burst Mode OPERATION
BURST LOSS
10
68.1k
FREQ
VOUT1
5V
7A
VOUT1
SENSE2+
SENSE2–
VFB2
RUN1
RUN2
RUN3
3mΩ
10k
POWER LOSS (mW)
VIN
2.5V TO 28V
(START-UP ABOVE 5V)
EFFICIENCY (%)
0.33µH
100
VIN = 12V
90 VOUT1 = 5V
TG1
68.1k
0.001
0.01
0.1
LOAD CURRENT (A)
1
10
0.1
7815 TA01b
COUT2
33µF
×2
100k
SGND
7815 TA01a
7815f
For more information www.linear.com/LTC7815
1
LTC7815
ABSOLUTE MAXIMUM RATINGS
(Note 1)
Bias Input Supply Voltage (VBIAS)............... –0.3V to 40V
Buck Top Side Driver Voltages
(BOOST1, BOOST2) .............................. –0.3V to 46V
Boost Top Side Driver Voltages
(BOOST3) ............................................. –0.3V to 71V
Buck Switch Voltage (SW1, SW2) ................. –5V to 40V
Boost Switch Voltage (SW3) ......................... –5V to 65V
INTVCC, (BOOST1–SW1),
(BOOST2–SW2), (BOOST3–SW3)............ –0.3V to 6V
BG1, BG2, BG3, TG1, TG2, TG3....................... (Note 8)
RUN1, RUN2, RUN3 ..................................... –0.3V to 8V
Maximum Current Sourced Into Pin
from Source >8V...............................................100µA
SENSE1+, SENSE2 +, SENSE1–
SENSE2 – Voltages.................................. –0.3V to 28V
SENSE3 +, SENSE3– Voltages...................... –0.3V to 40V
FREQ Voltages.......................................–0.3V to INTVCC
EXTVCC....................................................... –0.3V to 14V
ITH1, ITH2, ITH3, VFB1, VFB2, VFB3 Voltages..... –0.3V to 6V
PLLIN/MODE, PGOOD1, OV3 Voltages ......... –0.3V to 6V
TRACK/SS1, TRACK/SS2, SS3 Voltages ...... –0.3V to 6V
Operating Junction Temperature Range (Notes 2, 3)
LTC7815E, LTC7815I........................... –40°C to 125°C
LTC7815H........................................... –40°C to 150°C
Storage Temperature Range............... –65°C to 150°C
PIN CONFIGURATION
TG1
PGOOD1
TRACK/SS1
ITH1
VFB1
SENSE1+
SENSE1–
TOP VIEW
38 37 36 35 34 33 32
31 SW1
FREQ 1
30 BOOST1
PLLIN/MODE 2
SS3 3
29 BG1
SENSE3+ 4
28 SW3
SENSE3– 5
27 TG3
VFB3 6
26 BOOST3
39
PGND
ITH3 7
25 BG3
SGND 8
24 VBIAS
RUN1 9
23 EXTVCC
RUN2 10
22 INTVCC
RUN3 11
21 BG2
SENSE2– 12
20 BOOST2
TG2
SW2
OV3
TRACK/SS2
ITH2
VFB2
SENSE2+
13 14 15 16 17 18 19
UHF PACKAGE
38-LEAD (5mm × 7mm) PLASTIC QFN
TJMAX = 150°C, qJA = 34.7°C/W, qJC = 2°C/W
EXPOSED PAD (PIN 39) IS PGND, MUST BE SOLDERED TO PCB
7815f
2
For more information www.linear.com/LTC7815
LTC7815
ORDER INFORMATION
http://www.linear.com/product/LTC7815#orderinfo
LEAD FREE FINISH
TAPE AND REEL
PART MARKING*
PACKAGE DESCRIPTION
TEMPERATURE RANGE
LTC7815EUHF#PBF
LTC7815EUHF#TRPBF
7815
38-Lead (5mm × 7mm) Plastic QFN
–40°C to 125°C
LTC7815IUHF#PBF
LTC7815IUHF#TRPBF
7815
38-Lead (5mm × 7mm) Plastic QFN
–40°C to 125°C
LTC7815HUHF#PBF
LTC7815HUHF#TRPBF
7815
38-Lead (5mm × 7mm) Plastic QFN
–40°C to 150°C
Consult ADI Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container.
For more information on lead free part marking, go to: http://www.linear.com/leadfree/
For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/. Some packages are available in 500 unit reels through
designated sales channels with #TRMPBF suffix.
ELECTRICAL CHARACTERISTICS
The l denotes the specifications which apply over the specified operating
junction temperature range, otherwise specifications are at TA = 25°C (Notes 2, 4). VBIAS = 12V, VRUN1,2,3 = 5V, EXTVCC = 0V unless
otherwise noted.
SYMBOL
PARAMETER
VBIAS
Bias Input Supply Operating Voltage
Range
VFB1,2
Buck Regulated Feedback Voltage
VFB3
Boost Regulated Feedback Voltage
CONDITIONS
MAX
UNITS
38
V
(Note 4); ITH1,2 Voltage = 1.2V
0°C to 85°C, All Grades
LTC7815E, LTC7815I
LTC7815H
l
l
0.792
0.788
0.786
0.800
0.800
0.800
0.808
0.812
0.812
V
V
V
(Note 4); ITH3 Voltage = 1.2V
0°C to 85°C, All Grades
LTC7815E, LTC7815I
LTC7815H
l
l
1.183
1.181
1.176
1.200
1.200
1.200
1.214
1.218
1.218
V
V
V
–2
±50
nA
0.002
0.02
%/V
Feedback Current
(Note 4)
VREFLNREG
Reference Voltage Line Regulation
(Note 4); VIN = 4.5V to 38V
VLOADREG
Output Voltage Load Regulation
Transconductance Amplifier gm
TYP
4.5
IFB1,2,3
gm1,2,3
MIN
(Note 4)
Measured in Servo Loop;
∆ITH Voltage = 1.2V to 0.7V
l
0.01
0.1
%
Measured in Servo Loop;
∆ITH Voltage = 1.2V to 2V
l
–0.01
–0.1
%
(Note 4); ITH1,2,3 = 1.2V;
Sink/Source 5µA
2
mmho
7815f
For more information www.linear.com/LTC7815
3
LTC7815
ELECTRICAL
CHARACTERISTICS
The
l denotes the specifications which apply over the specified operating
junction temperature range, otherwise specifications are at TA = 25°C (Notes 2, 4). VBIAS = 12V, VRUN1,2,3 = 5V, EXTVCC = 0V unless
otherwise noted.
SYMBOL
PARAMETER
CONDITIONS
IQ
Input DC Supply Current
(Note 5)
Pulse-Skipping or
Forced Continuous Mode
(One Channel On)
RUN1 = 5V and RUN2,3 = 0V or
RUN2 = 5V and RUN1,3 = 0V or
RUN3 = 5V and RUN1,2 = 0V
VFB1, 2 ON = 0.83V (No Load)
VFB3 = 1.25V
Pulse-Skipping or
Forced Continuous Mode
(All Channels On)
RUN1,2,3 = 5V,
VFB1,2 = 0.83V (No Load)
VFB3 = 1.25V
Sleep Mode
(One Channel On, Buck)
RUN1 = 5V and RUN2,3 = 0V or
RUN2 = 5V and RUN1,3 = 0V
VFB,ON = 0.83V (No Load)
Sleep Mode
(One Channel On, Boost)
UVLO
MIN
TYP
MAX
UNITS
1.5
mA
3
mA
28
35
48
59
µA
RUN3 = 5V and RUN1,2 = 0V
VFB3 = 1.25V
33
53
µA
Sleep Mode
(Buck and Boost Channel On)
RUN1 = 5V and RUN2 = 0V or
RUN2 = 5V and RUN1 = 0V
RUN3 = 5V
VFB1,2 = 0.83V (No Load)
VFB3 = 1.25V
33
40
46
59
µA
Sleep Mode
(All Three Channels On)
RUN1,2,3 = 5V,
VFB1,2 = 0.83V (No Load)
VFB3 = 1.25V
38
56
µA
Shutdown
RUN1,2,3 = 0V
10
20
µA
Undervoltage Lockout
INTVCC Ramping Up
l
INTVCC Ramping Down
l
l
l
4.15
4.5
V
3.5
3.8
4.0
V
7
10
13
%
±1
µA
VOVL1,2
Buck Feedback Overvoltage Protection
Measured at VFB1,2 Relative to
Regulated VFB1,2
ISENSE1,2+
SENSE+ Pin Current
Bucks (Channels 1 and 2) VOUT = 3.3V
ISENSE3+
SENSE+ Pin Current
Boost (Channel 3)
170
ISENSE1,2–
SENSE– Pin Current
Bucks (Channels 1 and 2)
VOUT = 3.3V
VOUT1,2 > VINTVCC + 0.5V
700
µA
±2
µA
µA
±1
µA
ISENSE3 –
SENSE– Pin Current
Boost (Channel 3)
VSENSE3+, VSENSE3 – = 12V
DFMAX,TG
Maximum Duty Factor for TG
Bucks (Channels 1,2) in Dropout, FREQ = 0V
Boost (Channel 3) in Overvoltage
DFMAX,BG
Maximum Duty Factor for BG
Bucks (Channels 1,2) in Overvoltage
Boost (Channel 3)
ITRACK/SS1,2
Soft-Start Charge Current
VTRACK/SS1,2 = 0V
3
5
8
µA
ISS3
Soft-Start Charge Current
VSS3 = 0V
3
5
8
µA
VRUN1 ON
VRUN2,3 ON
RUN1 Pin Threshold
RUN2,3 Pin Threshold
VRUN1 Rising
VRUN2,3 Rising
1.18
1.21
1.24
1.27
1.32
1.33
V
V
VRUN1,2,3 Hyst
RUN Pin Hysteresis
l
l
98
100
%
%
100
90
%
%
70
VSENSE1,2,3(MAX) Maximum Current Sense Threshold
VSENSE3(CM)
97
VFB1,2 = 0.7V, VSENSE1,2– = 3.3V
VFB1,2,3 = 1.1V, VSENSE3 + = 12V
SENSE3 Pins Common Mode Range
(BOOST Converter Input Supply Voltage)
l
43
2.5
50
mV
57
mV
38
V
7815f
4
For more information www.linear.com/LTC7815
LTC7815
ELECTRICAL
CHARACTERISTICS
The
l denotes the specifications which apply over the specified operating
junction temperature range, otherwise specifications are at TA = 25°C (Notes 2, 4). VBIAS = 12V, VRUN1,2,3 = 5V, EXTVCC = 0V unless
otherwise noted.
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
Gate Driver
TG1,2
Pull-Up On-Resistance
Pull-Down On-Resistance
2.5
1.5
Ω
Ω
BG1,2
Pull-Up On-Resistance
Pull-Down On-Resistance
2.4
1.1
Ω
Ω
TG3
Pull-Up On-Resistance
Pull-Down On-Resistance
1.2
1.0
Ω
Ω
BG3
Pull-Up On-Resistance
Pull-Down On-Resistance
1.2
1.0
Ω
Ω
TG1,2,3 tr
TG1,2,3 tf
TG Transition Time:
Rise Time
Fall Time
(Note 6)
CLOAD = 3300pF
CLOAD = 3300pF
25
16
ns
ns
BG1,2,3 tr
BG1,2,3 tf
BG Transition Time:
Rise Time
Fall Time
(Note 6)
CLOAD = 3300pF
CLOAD = 3300pF
28
13
ns
ns
TG/BG t1D
Top Gate Off to Bottom Gate On Delay
Synchronous Switch-On Delay Time
CLOAD = 3300pF Each Driver Bucks (Channels 1, 2)
Boost (Channel 3)
25
30
ns
ns
BG/TG t1D
Bottom Gate Off to Top Gate On Delay
Top Switch-On Delay Time
CLOAD = 3300pF Each Driver Bucks (Channels 1, 2)
Boost (Channel 3)
20
20
ns
ns
tON(MIN)1,2
Buck Minimum On-Time
(Note 7)
45
ns
tON(MIN)3
Boost Minimum On-Time
(Note 7)
70
ns
INTVCC Linear Regulator
VINTVCCVBIAS
Internal VCC Voltage
6V < VBIAS < 38V, VEXTVCC = 0V, IINTVCC = 0mA
VLDOVBIAS
INTVCC Load Regulation
ICC = 0mA to 100mA, VEXTVCC = 0V
VINTVCCEXT
Internal VCC Voltage
6V < VEXTVCC < 13V, IINTVCC = 0mA
VLDOEXT
INTVCC Load Regulation
ICC = 0mA to 100mA, VEXTVCC = 8.5V
VEXTVCC
EXTVCC Switchover Voltage
EXTVCC Ramping Positive
VLDOHYS
EXTVCC Hysteresis
5.0
5.0
4.5
5.4
5.6
V
0.8
2.5
%
5.4
5.6
V
0.8
2.5
%
4.7
V
200
mV
Oscillator and Phase-Locked Loop
f25k
Programmable Frequency
RFREQ = 25k; PLLIN/MODE = DC Voltage
f65k
Programmable Frequency
RFREQ = 65k; PLLIN/MODE = DC Voltage
0.25
0.32
0.37
1.18
MHz
MHz
f100k
Programmable Frequency
RFREQ = 100k; PLLIN/MODE = DC Voltage
1.75
2.1
2.4
MHz
fLOW
Low Fixed Frequency
VFREQ = 0V PLLIN/MODE = DC Voltage
0.77
0.94
1.13
MHz
fHIGH
High Fixed Frequency
VFREQ = INTVCC; PLLIN/MODE = DC Voltage
1.2
1.44
1.75
MHz
fSYNC
Synchronizable Frequency
PLLIN/MODE = External Clock
l
0.32
2.25
MHz
PLLIN VIH
PLLIN/MODE Input High Level
PLLIN/MODE = External Clock
l
2.5
PLLIN VIL
PLLIN/MODE Input Low Level
PLLIN/MODE = External Clock
l
l
V
0.5
V
7815f
For more information www.linear.com/LTC7815
5
LTC7815
ELECTRICAL CHARACTERISTICS
The l denotes the specifications which apply over the specified operating
junction temperature range, otherwise specifications are at TA = 25°C (Notes 2, 4). VBIAS = 12V, VRUN1,2,3 = 5V, EXTVCC = 0V unless
otherwise noted.
SYMBOL
PARAMETER
CONDITIONS
MIN
VPGL1
PGOOD1 Voltage Low
IPGOOD1 = 2mA
IPGOOD1
PGOOD1 Leakage Current
VPGOOD1 = 5V
VPG1
PGOOD1 Trip Level
VFB1 with Respect to Set Regulated Voltage
VFB1 Ramping Negative
TYP
MAX
UNITS
0.2
0.4
V
±1
µA
–7
%
PGOOD1 Output
–13
Hysteresis
2.5
VFB1 Ramping Positive
7
Hysteresis
TPG1
–10
Delay For Reporting a Fault
10
%
13
%
2.5
%
40
µs
OV3 Boost Overvoltage Indicator Output
VOV3L
OV3 Voltage Low
IOV3 = 2mA
IOV3
OV3 Leakage Current
VOV3 = 5V
0.2
VOV
OV3 Trip Level
VFB3 Ramping Positive with Respect to Set
Regulated Voltage
6
10
0.4
V
±1
µA
13
%
Hysteresis
1.5
%
VBOOST3 = 16V; VSW3 = 12V;
Forced Continuous Mode
65
µA
BOOST3 Charge Pump
IBST3
BOOST3 Charge Pump Available Output
Current
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2: The LTC7815 is tested under pulsed load conditions such that
TJ ≈ TA. The LTC7815E is guaranteed to meet performance specifications
from 0°C to 85°C. Specifications over the –40°C to 125°C operating
junction temperature range are assured by design, characterization and
correlation with statistical process controls. The LTC7815I is guaranteed
over the –40°C to 125°C operating junction temperature range and the
LTC7815H is guaranteed over the –40°C to 150°C operating junction
temperature range. High junction temperatures degrade operating
lifetimes; operating lifetime is derated for junction temperatures greater
than 125°C. Note that the maximum ambient temperature consistent with
these specifications is determined by specific operating conditions in
conjunction with board layout, the rated package thermal impedance and
other environmental factors. TJ is calculated from the ambient temperature
TA and power dissipation PD according to the following formula: TJ = TA +
(PD • θJA), where θJA = 34.7°C/W.
Note 3: This IC includes overtemperature protection that is intended to
protect the device during momentary overload conditions. The maximum
rated junction temperature will be exceeded when this protection is active.
Continuous operation above the specified absolute maximum operating
junction temperature may impair device reliability or permanently damage
the device.
Note 4: The LTC7815 is tested in a feedback loop that servos VITH1,2,3 to
a specified voltage and measures the resultant VFB. The specification at
85°C is not tested in production and is assured by design, characterization
and correlation to production testing at other temperatures (125°C for
the LTC7815E/LTC7815I, 150°C for the LTC7815H). For the LTC7815I
and LTC7815H, the specification at 0°C is not tested in production and is
assured by design, characterization and correlation to production testing
at –40°C.
Note 5: Dynamic supply current is higher due to the gate charge being
delivered at the switching frequency. See the Applications Information
section.
Note 6: Rise and fall times are measured using 10% and 90% levels. Delay
times are measured using 50% levels.
Note 7: The minimum on-time condition is specified for an inductor
peak-to-peak ripple current ≥ 40% of IMAX (See the Minimum On-Time
Considerations in the Applications Information section).
Note 8: Do not apply a voltage or current source to these pins. They must
be connected to capacitive loads only, otherwise permanent damage may
occur.
7815f
6
For more information www.linear.com/LTC7815
LTC7815
TYPICAL PERFORMANCE CHARACTERISTICS
Efficiency and Power Loss
vs Output Current (Buck)
Efficiency
vs Output Current (Buck)
BURST EFFICIENCY
1k
70
PULSE–SKIPPING
LOSS
60
100
50
10
40
BURST LOSS
30
FCM EFFICIENCY
20
0
0.0001
0.001
0.01
0.1
LOAD CURRENT (A)
FIGURE 9 CIRCUIT
VIN = 12V, VOUT = 5V
1
10
70
60
50
40
30
1
20
0.1
10 FIGURE 9 CIRCUIT
VOUT = 5V
0
0.0001 0.001
0.01
0.1
LOAD CURRENT (A)
PULSE–SKIPPING
EFFICIENCY
10
97
80
EFFICIENCY (%)
FCM LOSS
POWER LOSS (mW)
EFFICIENCY (%)
80
90
EFFICIENCY (%)
90
Efficiency vs Input Voltage (Buck)
100
100
10k
100
90
87
83 FIGURE 9 CIRCUIT
VOUT = 5V
ILOAD = 5A
80
0
5
10 15 20 25 30
INPUT VOLTAGE (V)
VIN = 12V
VIN = 20V
1
93
10
Load Step (Buck)
Burst Mode Operation
Load Step (Buck)
Pulse-Skipping Mode
Load Step (Buck)
Forced Continuous Mode
VOUT
100mV/DIV
AC-COUPLED
VOUT
100mV/DIV
AC-COUPLED
VOUT
100mV/DIV
AC-COUPLED
IL
3A//DIV
IL
3A//DIV
IL
3A//DIV
VIN = 12V
VOUT = 5V
FIGURE 9 CIRCUIT
20µs/DIV
7815 G04
VIN = 12V
VOUT = 5V
FIGURE 9 CIRCUIT
Inductor Current at Light Load
(Buck)
40
7815 G03
7815 G02
7815 G01
35
7815 G05
20µs/DIV
VIN = 12V
VOUT = 5V
FIGURE 9 CIRCUIT
20µs/DIV
7815 G06
Buck Regulated Feedback Voltage
vs Temperature
Soft Start-Up (Buck)
FORCED
CONTINUOUS
MODE
VOUT1
2V/DIV
VOUT2
2V/DIV
Burst Mode
OPERATION
3A/DIV
RUN1/
RUN2
5V/DIV
PULSE–
SKIPPING
MODE
0.5µs/DIV
VIN = 12V
VOUT = 5V
ILOAD = 1mA
FIGURE 9 CIRCUIT
7815 G07
VIN = 12V
FIGURE 9 CIRCUIT
5ms/DIV
7815 G08
REGULATED FEEDBACK VOLTAGE (mV)
808
806
804
802
800
798
796
794
792
–75 –50 –25
0 25 50 75 100 125 150
TEMPERATURE (°C)
7815 G09
7815f
For more information www.linear.com/LTC7815
7
LTC7815
TYPICAL PERFORMANCE CHARACTERISTICS
Efficiency and Power Loss
vs Output Current (Boost)
Efficiency
vs Output Current (Boost)
1k
70
100
60
50
BURST
LOSS
30
20
10
0
0.0001
PULSE–SKIPPING 10
LOSS
FCM EFFICIENCY
0.001
0.01
0.1
1
OUTPUT CURRENT (A)
FIGURE 9 CIRCUIT
VIN = 5V, VOUT = 10V, Bias = VIN
70
60
50
40
30
20
1
PULSE–SKIPPING
EFFICIENCY
EFFICIENCY (%)
80
POWER LOSS (mW)
EFFICIENCY (%)
FCM LOSS
40
10
0.1
10
FIGURE 9 CIRCUIT
VBIAS = VIN
VOUT = 10V
0
0.0001
92
90
88
86
82
80
10
IL
5A/DIV
2
3
7815 G11
VOUT
100mV/DIV
AC-COUPLED
IL
5A/DIV
IL
5A/DIV
VOUT = 10V
VIN = 5V
FIGURE 9 CIRCUIT
Inductor Current at Light Load
(Boost)
50µs/DIV
7
8
Load Step (Boost)
Forced Continuous Mode
VOUT
100mV/DIV
AC-COUPLED
7815 G13
4
5
6
INPUT VOLTAGE (V)
7815 G12
Load Step (Boost)
Pulse-Skipping Mode
VOUT
100mV/DIV
AC-COUPLED
50µs/DIV
FIGURE 9 CIRCUIT
98 VBIAS = VIN
VOUT = 10V
96
ILOAD = 2A
94
84
VIN = 7V
VIN = 5V
0.001
0.01
0.1
1
OUTPUT CURRENT (A)
7815 G10
Load Step (Boost)
Burst Mode Operation
VOUT = 10V
VIN = 5V
FIGURE 9 CIRCUIT
100
90
BURST EFFICIENCY
EFFICIENCY (%)
90
80
100
10k
100
Efficiency vs Input Voltage
(Boost)
7815 G14
VOUT = 10V
VIN = 5V
FIGURE 9 CIRCUIT
50µs/DIV
7815 G15
Boost Regulated Feedback
Voltage vs Temperature
Soft Start-Up (Boost)
FORCED
CONTINUOUS
MODE
VOUT3
2V/DIV
Burst Mode
OPERATION
5A/DIV
RUN3
5V/DIV
PULSESKIPPING
MODE
GND
VOUT = 10V
VIN = 5V
ILOAD = 1mA
FIGURE 9 CIRCUIT
1µs/DIV
7815 G16
VIN = 5V
FIGURE 9 CIRCUIT
5ms/DIV
7815 G17
REGULATED FEEDBACK VOLTAGE (V)
1.212
1.209
1.206
1.203
1.200
1.197
1.194
1.191
1.188
–75 –50 –25
0 25 50 75 100 120 150
TEMPERATURE (°C)
7815 G18
7815f
8
For more information www.linear.com/LTC7815
LTC7815
TYPICAL PERFORMANCE CHARACTERISTICS
5.6
6.0
EXTVCC = 0V
5.4
5.4
5.3
5.2
5.8
EXTVCC = 8.5V
5.2
INTVCC VOLTAGE (V)
INTVCC VOLTAGE (V)
EXTVCC Switchover and INTVCC
Voltages vs Temperature
EXTVCC AND INTVCC VOLTAGE (V)
5.5
INTVCC and EXTVCC
vs Load Current
INTVCC Line Regulation
5.0
4.8
EXTVCC = 5V
4.6
4.4
5.1
4.2
5.0
0
5
10
15 20 25 30
INPUT VOLTAGE (V)
35
4.0
40
20
60
80
40
LOAD CURRENT (mA)
7815 G19
SENSE CURRENT (µA)
SENSE CURRENT (µA)
500
400
300
SENSE3 PIN
5
10 15 20 25 30 35
VSENSE COMMON MODE VOLTAGE (V)
800
180
VOUT > INTVCC + 0.5V
500
400
300
50
BUCK
40
30
20
10
0
0
10 20 30 40 50 60 70 80 90 100
DUTY CYCLE (%)
7815 G25
120
100
80
60
20
VOUT < INTVCC – 0.5V
0
–75 –50 –25
0 25 50 75 100 125 150
TEMPERATURE (°C)
SENSE3– PIN
0 25 50 75 100 125 150
TEMPERATURE (°C)
60
7815 G24
Maximum Current Sense
Threshold vs ITH Voltage
TRACK/SS Pull-Up Current
vs Temperature
6.00
50
5.75
40
TRACK/SS CURRENT (µA)
MAXIMUM CURRENT SENSE VOLTAGE (mV)
MAXIMUM CURRENT SENSE VOLTAGE (mV)
BOOST
140
7815 G23
Maximum Current Sense
Threshold vs Duty Cycle
60
SENSE3+ PIN
40
7815 G22
70
VIN = 12V
160
600
0
–75 –50 –25
40
80
0 25 50 75 100 125 150
TEMPERATURE (°C)
Boost SENSE Pin Total Input
Current vs Temperature
200
100
0
EXTVCC FALLING
4.4
7815 G21
200
100
0
4.6
900
700
600
EXTVCC RISING
4.8
Buck SENSE– Pin Input Bias
Current vs Temperature
SENSE1, 2 PINS
200
5.0
7815 G20
SENSE Pins Total Input Current
vs VSENSE Voltage
700
5.2
4.0
–75 –50 –25
100
SENSE CURRENT (µA)
800
INTVCC
5.4
4.2
VBIAS = 12V
0
5.6
30
20
10
0
–10
PULSE-SKIPPING
FORCED CONTINUOUS
Burst Mode OPERATION
–20
–30
0
0.2
0.4
0.6 0.8
ITH (V)
1
1.2
1.4
7815 G26
5.50
5.25
5.00
4.75
4.50
4.25
4.00
–75 –50 –25
0 25 50 75 100 125 150
TEMPERATURE (°C)
7815 G27
7815f
For more information www.linear.com/LTC7815
9
LTC7815
TYPICAL PERFORMANCE CHARACTERISTICS
Shutdown Current
vs Input Voltage
Shutdown Current vs Temperature
20
Quiescent Current vs Temperature
25
VBIAS = 12V
80
70
16
14
12
10
8
20
QUIESCENT CURRENT (µA)
SHUTDOWN CURRENT (µA)
SHUTDOWN CURRENT (µA)
18
15
10
5
6
0
0 25 50 75 100 125 150
TEMPERATURE (°C)
5
7815 G28
10
15
20
25
30
VBIAS INPUT VOLTAGE (V)
2.25
35
30
CHANNEL 1 ON
20
0
–75 –50 –25
40
7815 G30
Undervoltage Lockout Threshold
vs Temperature
4.4
FREQ = 100k
4.3
100 200 300 400 500 600 700 800
FEEDBACK VOLTAGE (mV)
1.65
FREQ = INTVCC
1.25
0.85
–75 –50 –25
0
25
50
3.4
–75 –50 –25
75 100 125 150
RUN1 FALLING
1.05
0 25 50 75 100 125 150
TEMPERATURE (°C)
7815 G34
0 25 50 75 100 125 150
TEMPERATURE (°C)
7815 G33
Charge Pump Charging Current
vs Switch Voltage
VBOOST3 = 16V
90 VSW3 = 12V
100
CHARGE PUMP CHARGING CURRENT (µA)
RUN2,3 FALLING
CHARGE PUMP CHARGING CURRENT (µA)
RUN1 RISING
1.20
1.00
–75 –50 –25
3.7
3.5
100
RUN2,3 RISING
FALLING
3.8
Charge Pump Charging Current
vs Operating Frequency
1.35
1.10
3.9
7815 G32
1.40
1.15
4.0
TEMPERATURE (°C)
Shutdown (RUN) Threshold
vs Temperature
1.25
4.1
3.6
FREQ = GND
7815 G31
1.30
INTVCC VOLTAGE (V)
1.85
1.05
0
RISING
4.2
1.45
0 25 50 75 100 125 150
TEMPERATURE (°C)
7815 G29
2.05
FREQUENCY (MHz)
MAXIMUM CURRENT SENSE VOLTAGE (mV)
ALL CHANNELS ON
40
Oscillator Frequency
vs Temperature
Buck Foldback Current Limit
RUN PIN VOLTAGE (V)
50
10
4
–75 –50 –25
70
65
60
55
50
45
40
35
30
25
20
15
10
5
0
60
–55°C
80
25°C
70
60
50
150°C
40
30
20
10
0
0
500 1000 1500 2000 2500
OPERATING FREQUENCY (kHz)
3000
7815 G35
VBOOST3 – VSW3 = 4V
90
80
70
60
50
40
30
20
FREQ = 0V
FREQ = INTVCC
FREQ = 100k
10
0
5
10
15
20
25
30
SWITCH VOLTAGE (V)
35
40
7815 G36
7815f
10
For more information www.linear.com/LTC7815
LTC7815
PIN FUNCTIONS
FREQ (Pin 1): The Frequency Control Pin for the Internal
VCO. Connecting the pin to GND forces the VCO to a fixed
low frequency of 0.94MHz. Connecting the pin to INTVCC
forces the VCO to a fixed high frequency of 1.44MHz.
Other frequencies between 0.32MHz and 2.25MHz can
be programmed using a resistor between FREQ and GND.
The resistor and an internal 20µA source current create a
voltage used by the internal oscillator to set the frequency.
PLLIN/MODE (Pin 2): External Synchronization Input to
Phase Detector and Forced Continuous Mode Input. When
an external clock is applied to this pin, the phase-locked
loop will force the rising TG1 signal to be synchronized
with the rising edge of the external clock, and the regulators operate in forced continuous mode. When not synchronizing to an external clock, this input, which acts on
all three controllers, determines how the LTC7815 operates at light loads. Pulling this pin to ground selects Burst
Mode operation. An internal 100k resistor to ground also
invokes Burst Mode operation when the pin is floated.
Tying this pin to INTVCC forces continuous inductor current operation. Tying this pin to a voltage greater than
1.2V and less than INTVCC – 1.3V selects pulse-skipping
operation. This can be done by connecting a 100k resistor
from this pin to INTVCC.
SGND (Pin 8): Small Signal Ground common to all three
controllers, must be routed separately from high current grounds to the common (–) terminals of the CIN
capacitors.
RUN1, RUN2, RUN3 (Pins 9, 10, 11): Digital Run Control
Inputs for Each Controller. Forcing RUN1 below 1.17V
and RUN2/RUN3 below 1.20V shuts down that controller.
Forcing all of these pins below 0.7V shuts down the entire
LTC7815, reducing quiescent current to approximately
10µA.
OV3 (Pin 17): Overvoltage Open-Drain Logic Output for
the Boost Regulator. OV3 is pulled to ground when the
voltage on the VFB3 pin is under 110% of its set point,
and becomes high impedance when VFB3 goes over 110%
of its set point.
INTVCC (Pin 22): Output of the Internal Linear Low
Dropout Regulator. The driver and control circuits are
powered from this voltage source. Must be decoupled
to PGND with a minimum of 4.7µF ceramic or tantalum
capacitor.
EXTVCC (Pin 23): External Power Input to an Internal LDO
Connected to INTVCC. This LDO supplies INTVCC power,
bypassing the internal LDO powered from VBIAS whenever
EXTVCC is higher than 4.7V. See EXTVCC Connection in the
Applications Information section. Do not float or exceed
14V on this pin.
VBIAS (Pin 24): Main Bias Input Supply Pin. A bypass
capacitor should be tied between this pin and the SGND
pin.
BG1, BG2, BG3 (Pins 29, 21, 25): High Current Gate
Drives for Bottom (Synchronous) N-Channel MOSFETs.
Voltage swing at these pins is from ground to INTVCC.
BOOST1, BOOST2, BOOST3 (Pins 30, 20, 26):
Bootstrapped Supplies to the Top Side Floating Drivers.
Capacitors are connected between the BOOST and SW
pins and Schottky diodes are tied between the BOOST
and INTVCC pins. Voltage swing at the BOOST pins is from
INTVCC to (VIN + INTVCC).
SW1, SW2, SW3 (Pins 31, 19, 28): Switch Node
Connections to Inductors.
TG1, TG2, TG3 (Pins 32, 18, 27): High Current Gate
Drives for Top N-Channel MOSFETs. These are the outputs
of floating drivers with a voltage swing equal to INTVCC
superimposed on the switch node voltage SW.
PGOOD1 (Pin 33): Open-Drain Logic Output. PGOOD1 is
pulled to ground when the voltage on the VFB1 pin is not
within ±10% of its set point.
TRACK/SS1, TRACK/SS2, SS3 (Pins 34, 16, 3): External
Tracking and Soft-Start Input. For the buck channels, the
LTC7815 regulates the VFB1,2 voltage to the smaller of
0.8V, or the voltage on the TRACK/SS1,2 pin. For the
boost channel, the LTC7815 regulates the VFB3 voltage
to the smaller of 1.2V, or the voltage on the SS3 pin. An
7815f
For more information www.linear.com/LTC7815
11
LTC7815
PIN FUNCTIONS
internal 5µA pull-up current source is connected to this
pin. A capacitor to ground at this pin sets the ramp time
to final regulated output voltage. Alternatively, a resistor divider on another voltage supply connected to the
TRACK/SS pins of the buck channels allow the LTC7815
buck outputs to track the other supply during start-up.
SENSE1+, SENSE2+, SENSE3+ (Pins 37, 13, 4): The (+)
Input to the Differential Current Comparators. The ITH pin
voltage and controlled offsets between the SENSE– and
SENSE+ pins in conjunction with RSENSE set the current
trip threshold. For the boost channel, the SENSE3+ pin
supplies current to the current comparator.
ITH1, ITH2, ITH3 (Pins 35, 15, 7): Error Amplifier Outputs
and Switching Regulator Compensation Points. Each
associated channel’s current comparator trip point
increases with this control voltage.
SENSE1–, SENSE2–, SENSE3– (Pins 38, 12, 5): The
(–) Input to the Differential Current Comparators. When
SENSE1,2– for the buck channels is greater than INTVCC,
then SENSE1,2– pin supplies current to the current
comparator.
VFB1, VFB2, VFB3 (Pins 36, 14, 6): Receives the remotely
sensed feedback voltage for each controller from an external resistive divider across the output.
PGND (Exposed Pad Pin 39): Driver Power Ground.
Connects to the sources of bottom N-channel MOSFETs
and the (–) terminal(s) of CIN. The exposed pad must
be soldered to the PCB for rated electrical and thermal
performance.
7815f
12
For more information www.linear.com/LTC7815
For more information www.linear.com/LTC7815
4.7V
+
–
EXTVCC
VBIAS
PLLIN/MODE
FREQ
LDO
LDO
EN
5.4V
SGND
SYNC
DET
CLP
VCO
5.4V
EN
100k
20µA
+
–
CLK1
CLK2
INTVCC
PFD
0.72V
VFB1
0.88V
6.8V
RUN
11V
SHDN
RST
2(VFB)
7µA CH1
160nA CH2
SLOPE COMP
2.8V
0.65V
Q
R
ICMP
Q
S
SLEEP
SHDN
FOLDBACK
–+
+
–
BOT
TOPON
DROPOUT
DET
+
–
+
–
BUCK CHANNELS 1 AND 2
3mV
–+
PGOOD1
OV
+
–
SHDN
+
–
–
EA +
+
IR
SWITCHING
LOGIC
5µA
0.88V
PGND
BG
SW
TG
TRACK/SS
ITH
VFB
SENSE–
SENSE+
INTVCC
0.80V
TRACK/SS
BOT
TOP
BOOST
7815 BD
CSS
CB
DB
INTVCC
L
RB
D
CC2
CC
RA
VIN1,2
RC
RSENSE
COUT
CIN
VOUT1,2
LTC7815
FUNCTIONAL DIAGRAM
7815f
13
14
OV3
+
–
VFB3
1.32V
PLLIN/MODE
CLK1
RUN3
ICMP
For more information www.linear.com/LTC7815
11V
160nA
SHDN
SLOPE COMP
2.8V
0.7V
Q
0.425V
Q
S
R
+
–
BOOST CHANNEL 3
SNSLO
5µA
OV
+
–
2mV
1.32V
+
–
SS3
ITH3
VFB3
SENSE3+
SENSE3–
PGND
BG3
SW3
TG3
BOOST3
INTVCC
1.2V
SS3
BOT
TOP
–
EA +
+
2V
IR
SWITCHING
LOGIC
+
+– –
SLEEP
SNSLO
–+
+
–
SHDN
BOTON
7815 BD
CSS
CB
DB
INTVCC
L
RB
CC2
CC
RA
VOUT3
RC
RSENSE
CIN
COUT
VOUT3
VIN3
LTC7815
FUNCTIONAL DIAGRAM
7815f
LTC7815
OPERATION
(Refer to Functional Diagram)
Main Control Loop
The LTC7815 uses a constant frequency, current mode
step-down architecture. The two buck controllers, channels 1 and 2, operate 180 degrees out of phase with each
other. The boost controller, channel 3, operates in phase
with channel 1. During normal operation, the external
top MOSFET for the buck channels (the external bottom
MOSFET for the boost channel) is turned on when the
clock for that channel sets the RS latch, and is turned off
when the main current comparator, ICMP, resets the RS
latch. The peak inductor current at which ICMP trips and
resets the latch is controlled by the voltage on the ITH pin,
which is the output of the error amplifier EA. The error
amplifier compares the output voltage feedback signal at
the VFB pin, (which is generated with an external resistor divider connected across the output voltage, VOUT, to
ground) to the internal 0.800V reference voltage for the
bucks (1.2V reference voltage for the boost). When the
load current increases, it causes a slight decrease in VFB
relative to the reference, which causes the EA to increase
the ITH voltage until the average inductor current matches
the new load current.
After the top MOSFET for the bucks (the bottom MOSFET
for the boost) is turned off each cycle, the bottom MOSFET
is turned on (the top MOSFET for the boost) until either
the inductor current starts to reverse, as indicated by the
current comparator IR, or the beginning of the next clock
cycle.
INTVCC/EXTVCC Power
Power for the top and bottom MOSFET drivers and most
other internal circuitry is derived from the INTVCC pin.
When the EXTVCC pin is left open or tied to a voltage less
than 4.7V, the VBIAS LDO (low dropout linear regulator)
supplies 5.4V from VBIAS to INTVCC. If EXTVCC is taken
above 4.7V, the VBIAS LDO is turned off and an EXTVCC
LDO is turned on. Once enabled, the EXTVCC LDO supplies
5.4V from EXTVCC to INTVCC. Using the EXTVCC pin allows
the INTVCC power to be derived from a high efficiency
external source such as one of the LTC7815 switching
regulator outputs.
Each top MOSFET driver is biased from the floating bootstrap capacitor CB, which normally recharges during each
cycle through an external diode when the switch voltage
goes low.
For buck channels 1 and 2, if the buck’s input voltage
decreases to a voltage close to its output, the loop may
enter dropout and attempt to turn on the top MOSFET
continuously. The dropout detector detects this and forces
the top MOSFET off for a short time every tenth cycle to
allow CB to recharge resulting in about 98% duty cycle at
1MHz operation.
Shutdown and Start-Up (RUN1, RUN2, RUN3 and
TRACK/SS1, TRACK/SS2, SS3 Pins)
The three channels of the LTC7815 can be independently
shut down using the RUN1, RUN2 and RUN3 pins. Pulling
RUN1 below 1.17V and RUN2/RUN3 below 1.20V shuts
down the main control loop for that channel. Pulling all
three pins below 0.7V disables all controllers and most
internal circuits, including the INTVCC LDOs. In this state,
the LTC7815 draws only 10µA of quiescent current.
Releasing a RUN pin allows a small internal current to pull
up the pin to enable that controller. The RUN1 pin has a
7µA pull-up current while the RUN2 and RUN3 pins have
a smaller 160nA. The 7µA current on RUN1 is designed
to be large enough so that the RUN1 pin can be safely
floated (to always enable the controller) without worry
of condensation or other small board leakage pulling the
pin down. This is ideal for always-on applications where
one or more controllers are enabled continuously and
never shut down.
Each RUN pin may also be externally pulled up or driven
directly by logic. When driving a RUN pin with a low
impedance source, do not exceed the absolute maximum
rating of 8V. Each RUN pin has an internal 11V voltage
clamp that allows the RUN pin to be connected through
a resistor to a higher voltage (for example, VBIAS), so
long as the maximum current in the RUN pin does not
exceed 100µA.
The start-up of each channel’s output voltage VOUT is controlled by the voltage on the TRACK/SS pin (TRACK/SS1 for
channel 1, TRACK/SS2 for channel 2, SS3 for channel 3).
When the voltage on the TRACK/SS pin is less than the
0.8V internal reference for the bucks and the 1.2V internal
7815f
For more information www.linear.com/LTC7815
15
LTC7815
OPERATION
reference for the boost, the LTC7815 regulates the VFB
voltage to the TRACK/SS pin voltage instead of the corresponding reference voltage. This allows the TRACK/
SS pin to be used to program a soft-start by connecting
an external capacitor from the TRACK/SS pin to SGND.
An internal 5µA pull-up current charges this capacitor
creating a voltage ramp on the TRACK/SS pin. As the
TRACK/SS voltage rises linearly from 0V to 0.8V/1.2V
(and beyond up to INTVCC), the output voltage VOUT rises
smoothly from zero to its final value.
Alternatively the TRACK/SS pins for buck channels 1 and 2
can be used to cause the start-up of VOUT to track that of
another supply. Typically, this requires connecting to the
TRACK/SS pin an external resistor divider from the other
supply to ground (see the Applications Information section).
Light Load Current Operation (Burst Mode Operation,
Pulse-Skipping, or Continuous Conduction)
(PLLIN/MODE Pin)
The LTC7815 can be enabled to enter high efficiency Burst
Mode operation, constant frequency pulse-skipping mode
or forced continuous conduction mode at low load currents. To select Burst Mode operation, tie the PLLIN/
MODE pin to ground. To select forced continuous operation, tie the PLLIN/MODE pin to INTVCC. To select pulseskipping mode, tie the PLLIN/MODE pin to a DC voltage
greater than 1.2V and less than INTVCC – 1.3V.
When a controller is enabled for Burst Mode operation,
the minimum peak current in the inductor is set to approximately 25% of the maximum sense voltage (30% for the
boost) even though the voltage on the ITH pin indicates a
lower value. If the average inductor current is higher than
the load current, the error amplifier EA will decrease the
voltage on the ITH pin. When the ITH voltage drops below
0.425V, the internal sleep signal goes high (enabling sleep
mode) and both external MOSFETs are turned off. The ITH
pin is then disconnected from the output of the EA and
parked at 0.450V.
In sleep mode, much of the internal circuitry is turned off,
reducing the quiescent current that the LTC7815 draws.
If channel 1 is in sleep mode and the other two are shut
down, the LTC7815 draws only 28µA of quiescent current.
If channels 1 and 3 are in sleep mode and channel 2 is shut
down, it draws only 33µA of quiescent current. If all three
controllers are enabled in sleep mode, the LTC7815 draws
only 38µA of quiescent. In sleep mode, the load current
is supplied by the output capacitor. As the output voltage decreases, the EA’s output begins to rise. When the
output voltage drops enough, the ITH pin is reconnected
to the output of the EA, the sleep signal goes low, and the
controller resumes normal operation by turning on the top
external MOSFET on the next cycle of the internal oscillator.
When a controller is enabled for Burst Mode operation,
the inductor current is not allowed to reverse. The reverse
current comparator (IR) turns off the bottom external
MOSFET (the top external MOSFET for the boost) just
before the inductor current reaches zero, preventing it
from reversing and going negative. Thus, the controller
operates in discontinuous operation.
In forced continuous operation or clocked by an external clock source to use the phase-locked loop (see the
Frequency Selection and Phase-Locked Loop section),
the inductor current is allowed to reverse at light loads or
under large transient conditions. The peak inductor current is determined by the voltage on the ITH pin, just as
in normal operation. In this mode, the efficiency at light
loads is lower than in Burst Mode operation. However,
continuous operation has the advantage of lower output
voltage ripple and less interference to audio circuitry. In
forced continuous mode, the output ripple is independent
of load current.
When the PLLIN/MODE pin is connected for pulse-skipping mode, the LTC7815 operates in PWM pulse-skipping
mode at light loads. In this mode, constant frequency
operation is maintained down to approximately 1% of
designed maximum output current. At very light loads, the
current comparator ICMP may remain tripped for several
cycles and force the external top MOSFET to stay off for
the same number of cycles (i.e., skipping pulses). The
inductor current is not allowed to reverse (discontinuous operation). This mode, like forced continuous operation, exhibits low output ripple as well as low audio noise
and reduced RF interference as compared to Burst Mode
operation. It provides higher low current efficiency than
forced continuous mode, but not nearly as high as Burst
Mode operation.
7815f
16
For more information www.linear.com/LTC7815
LTC7815
OPERATION
Frequency Selection and Phase-Locked Loop
(FREQ and PLLIN/MODE Pins)
that the external clock source swings from ground (0V)
to at least 2.5V.
The selection of switching frequency is a tradeoff between
efficiency and component size. Low frequency operation increases efficiency by reducing MOSFET switching
losses, but requires larger inductance and/or capacitance
to maintain low output ripple voltage.
Boost Controller Operation When VIN > VOUT
The switching frequency of the LTC7815’s controllers can
be selected using the FREQ pin.
If the PLLIN/MODE pin is not being driven by an external
clock source, the FREQ pin can be tied to SGND, tied
to INTVCC, or programmed through an external resistor.
Tying FREQ to SGND selects 0.94MHz while tying FREQ
to INTVCC selects 1.44MHz. Placing a resistor between
FREQ and SGND allows the frequency to be programmed
between 0.32MHz and 2.25MHz.
A phase-locked loop (PLL) is available on the LTC7815
to synchronize the internal oscillator to an external clock
source that is connected to the PLLIN/MODE pin. The
LTC7815’s phase detector adjusts the voltage (through
an internal lowpass filter) of the VCO input to align the
turn-on of controller 1’s external top MOSFET to the rising edge of the synchronizing signal. Thus, the turn-on
of controller 2’s external top MOSFET is 180 degrees out
of phase to the rising edge of the external clock source.
The VCO input voltage is pre-biased to the operating frequency set by the FREQ pin before the external clock is
applied. If prebiased near the external clock frequency,
the PLL loop only needs to make slight changes to the
VCO input in order to synchronize the rising edge of the
external clock’s to the rising edge of TG1. The ability to
pre-bias the loop filter allows the PLL to lock in rapidly
without deviating far from the desired frequency.
The typical capture range of the LTC7815’s phase-locked
loop is from approximately 0.3MHz to 2.3MHz, with a
guarantee over all manufacturing variations to be between
0.32MHz and 2.25MHz. In other words, the LTC7815’s
PLL is guaranteed to lock to an external clock source
whose frequency is between 0.32MHz and 2.25MHz.
The typical input clock thresholds on the PLLIN/MODE
pin are 1.6V (rising) and 1.1V (falling). It is recommended
When the input voltage to the boost channel rises above
its regulated VOUT voltage, the controller can behave differently depending on the mode, inductor current and
VIN voltage. In forced continuous mode, the loop works
to keep the top MOSFET on continuously once VIN rises
above VOUT. An internal charge pump delivers current to
the boost capacitor from the BOOST3 pin to maintain a
sufficiently high TG voltage. (The amount of current the
charge pump can deliver is characterized by two curves
in the Typical Performance Characteristics section.)
In pulse-skipping mode, if VIN is between 100% and
110% of the regulated VOUT voltage, TG3 turns on if the
inductor current rises above approximately 3% of the
programmed ILIM current. If the part is programmed in
Burst Mode operation under this same VIN window, then
TG3 turns on at the same threshold current as long as
the chip is awake (one of the buck channels is awake and
switching). If both buck channels are asleep or shut down
in this VIN window, then TG3 will remain off regardless of
the inductor current.
If VIN rises above 110% of the regulated VOUT voltage in
any mode, the controller turns on TG3 regardless of the
inductor current. In Burst Mode operation, however, the
internal charge pump turns off if the entire chip is asleep
(the two buck channels are asleep or shut down). With
the charge pump off, there would be nothing to prevent
the boost capacitor from discharging, resulting in an
insufficient TG voltage needed to keep the top MOSFET
completely on. The charge pump turns back on when the
chip wakes up, and it remains on as long as one of the
buck channels is actively switching.
Boost Controller at Low SENSE Pin Common Voltage
The current comparator of the boost controller is powered
directly from the SENSE3+ pin and can operate to voltages as low as 2.5V. Since this is lower than the VBIAS
UVLO of the chip, VBIAS can be connected to the output
of the boost controller, as illustrated in the typical application circuit in Figure 9. This allows the boost controller to
7815f
For more information www.linear.com/LTC7815
17
LTC7815
OPERATION
handle input voltage transients down to 2.5V while maintaining output voltage regulation. If the SENSE3+ rises
back above 2.5V, the SS3 pin will be released initiating a
new soft-start sequence.
Boost Overvoltage Indicator (OV3)
The two buck channels have an overvoltage comparator that guards against transient overshoots as well as
other more serious conditions that may overvoltage their
outputs. When the VFB1,2 pin rises by more than 10%
above its regulation point of 0.800V, the top MOSFET is
turned off and the bottom MOSFET is turned on until the
overvoltage condition is cleared.
The OV3 pin is an overvoltage indicator that signals
whether the output voltage of the channel 3 boost controller goes over its programmed regulated voltage. The
pin is connected to an open drain of an internal N-channel
MOSFET. The MOSFET turns on and pulls the OV3 pin low
when the VFB3 pin voltage is less than 110% of the 1.2V
reference voltage for the boost channel. The OV3 pin is
also pulled low when the RUN3 pin is low (shut down).
When the VFB3 pin voltage goes higher than 110% of the
1.2V reference, the MOSFET is turned off and the pin is
allowed to be pulled up by an external resistor to a source
no greater than 6V.
Channel 1 Power Good (PGOOD1)
Buck Foldback Current
Channel 1 has a PGOOD1 pin that is connected to an
open drain of an internal N-channel MOSFET. The MOSFET
turns on and pulls the PGOOD1 pin low when the VFB1 pin
voltage is not within ±10% of the 0.8V reference voltage
for the buck channel. The PGOOD1 pin is also pulled low
when the RUN1 pin is low (shut down). When the VFB1
pin voltage is within the ±10% requirement, the MOSFET
is turned off and the pin is allowed to be pulled up by an
external resistor to a source no greater than 6V.
When the buck output voltage falls to less than 70% of its
nominal level, foldback current limiting is activated, progressively lowering the peak current limit in proportion to
the severity of the overcurrent or short-circuit condition.
Foldback current limiting is disabled during the soft-start
interval (as long as the VFB voltage is keeping up with
the TRACK/SS1,2 voltage). There is no foldback current
limiting for the boost channel.
Buck Controller Output Overvoltage Protection
7815f
18
For more information www.linear.com/LTC7815
LTC7815
APPLICATIONS INFORMATION
The Typical Application on the first page is a basic
LTC7815 application circuit. LTC7815 can be configured
to use either DCR (inductor resistance) sensing or low
value resistor sensing. The choice between the two current sensing schemes is largely a design trade-off between
cost, power consumption, and accuracy. DCR sensing is
becoming popular because it saves expensive current
sensing resistors and is more power efficient, especially
in high current applications. However, current sensing
resistors provide the most accurate current limits for the
controller. Other external component selection is driven
by the load requirement, and begins with the selection of
RSENSE (if RSENSE is used) and inductor value. Next, the
power MOSFETs and Schottky diodes are selected. Finally,
input and output capacitors are selected.
Filter components mutual to the sense lines should be
placed close to the LTC7815, and the sense lines should
run close together to a Kelvin connection underneath the
current sense element (shown in Figure 1). Sensing current elsewhere can effectively add parasitic inductance
and capacitance to the current sense element, degrading
the information at the sense terminals and making the
programmed current limit unpredictable. If DCR sensing
is used (Figure 2b), sense resistor R1 should be placed
close to the switching node, to prevent noise from coupling into sensitive small-signal nodes.
TO SENSE FILTER
NEXT TO THE CONTROLLER
SENSE+ and SENSE– Pins
CURRENT FLOW
The SENSE+ and SENSE– pins are the inputs to the current comparators.
Buck Controllers (SENSE1+/SENSE1–,SENSE2+/SENSE2–):
The common mode voltage range on these pins is 0V to
28V (absolute maximum), enabling the LTC7815 to regulate buck output voltages up to a nominal 24V (allowing
margin for tolerances and transients). The SENSE+ pin
is high impedance drawing less than ≈ 1µA. This high
impedance allows the current comparators to be used
in inductor DCR sensing. The impedance of the SENSE–
pin changes depending on the common mode voltage.
When SENSE– is less than INTVCC –0.5V, it is high impedance, drawing less than ≈ 1µA. When SENSE– is above
INTVCC +0.5V, a higher current (≈700µA) flows into the
pin. Between INTVCC –0.5V and INTVCC +0.5V, the current
transitions from the smaller current to the higher current.
Boost Controller (SENSE3+/SENSE3–): The common mode
input range for these pins is 2.5V to 38V, allowing the boost
converter to operate from inputs over this full range. The
SENSE3+ pin also provides power to the current comparator and draws about 170µA during normal operation (when
not shut down or asleep in Burst Mode operation). There is
a small bias current of less than 1µA that flows out of the
SENSE3– pin. This high impedance on the SENSE3– pin
allows the current comparator to be used in inductor DCR
sensing.
INDUCTOR OR RSENSE
7815 F01
Figure 1. Sense Lines Placement with Inductor or Sense Resistor
Low Value Resistor Current Sensing
A typical sensing circuit using a discrete resistor is shown
in Figure 2a. RSENSE is chosen based on the required output current.
The current comparators have a maximum threshold
VSENSE(MAX) of 50mV. The current comparator threshold
sets the peak of the inductor current, yielding a maximum
average output current, IMAX, equal to the peak value less
half the peak-to-peak ripple current, ∆IL. To calculate the
sense resistor value, use the equation:
RSENSE =
VSENSE(MAX)
ΔI
IMAX + L
2
When using the buck controllers in very low dropout
conditions, the maximum output current level will be
reduced due to the internal compensation required to
meet stability criterion for buck regulators operating at
greater than 50% duty factor. A curve is provided in the
Typical Performance Characteristics section to estimate
this reduction in peak output current level depending upon
the operating duty factor.
7815f
For more information www.linear.com/LTC7815
19
LTC7815
APPLICATIONS INFORMATION
VIN1,2
(VOUT3)
INTVCC
BOOST
LTC7815
TG
RSENSE
SW
VOUT1,2
(VIN3)
BG
SENSE1,2+
(SENSE3–)
SENSE1, 2–
(SENSE3+)
CAP
PLACED NEAR SENSE PINS
SGND
Using the inductor ripple current value from the Inductor
Value Calculation section, the target sense resistor value
is:
7815 F02a
2a. Using a Resistor to Sense Current
VIN1,2
(VOUT3)
INTVCC
R(EQUIV) =
BOOST
LTC7815
L
SW
BG
SENSE1, 2+
(SENSE3–)
SENSE1, 2–
(SENSE3+)
INDUCTOR
TG
DCR
VOUT1,2
(VIN3)
R1
C1*
R2
SGND
7815 F02b
*PLACE C1 NEAR SENSE PINS
If the external R1||R2 • C1 time constant is chosen to
be exactly equal to the L/DCR time constant, the voltage
drop across the external capacitor is equal to the drop
across the inductor DCR multiplied by R2/(R1 + R2). R2
scales the voltage across the sense terminals for applications where the DCR is greater than the target sense
resistor value. To properly dimension the external filter
components, the DCR of the inductor must be known. It
can be measured using a good RLC meter, but the DCR
tolerance is not always the same and varies with temperature; consult the manufacturers’ data sheets for detailed
information.
(R1||R2) • C1 = L/DCR
RSENSE(EQ) = DCR(R2/(R1+R2))
2b. Using the Inductor DCR to Sense Current
Figure 2. Current Sensing Methods
To ensure that the application will deliver full load current over the full operating temperature range, determine
RSENSE(EQUIV), keeping in mind that the maximum current
sense threshold (VSENSE(MAX)) for the LTC7815 is fixed
at 50mV.
Next, determine the DCR of the inductor. Where provided,
use the manufacturer’s maximum value, usually given at
20°C. Increase this value to account for the temperature
coefficient of resistance, which is approximately 0.4%/°C.
A conservative value for TL(MAX) is 100°C.
To scale the maximum inductor DCR to the desired resistor value, use the divider ratio:
Inductor DCR Sensing
For applications requiring the highest possible efficiency at
high load currents, the LTC7815 is capable of sensing the
voltage drop across the inductor DCR, as shown in Figure 2b.
The DCR of the inductor represents the small amount of
DC winding resistance of the copper, which can be less
than 1mΩ for today’s low value, high current inductors.
In a high current application requiring such an inductor, conduction loss through a sense resistor would cost
several points of efficiency compared to DCR sensing.
VSENSE(MAX)
ΔI
IMAX + L
2
RD =
R SENSE(EQUIV)
DCRMAX at TL(MAX)
C1 is usually selected to be in the range of 0.1µF to 0.47µF.
This forces R1||R2 to around 2k, reducing error that might
have been caused by the SENSE+ pin’s ±1µA current.
The equivalent resistance R1||R2 is scaled to the room
temperature inductance and maximum DCR:
L
R1 R2 =
(DCR at 20°C) • C1
7815f
20
For more information www.linear.com/LTC7815
LTC7815
APPLICATIONS INFORMATION
inductance or frequency. For the buck controllers, ∆IL
increases with higher VIN:
The sense resistor values are:
R1=
R1! R2
R1• RD
; R2 =
RD
1− RD
The maximum power loss in R1 is related to duty cycle.
For the buck controllers, the maximum power loss will
occur in continuous mode at the maximum input voltage:
PLOSS R1=
(VIN(MAX) − VOUT ) • VOUT
(VOUT(MAX) − VIN ) • VIN
R1
Ensure that R1 has a power rating higher than this value.
If high efficiency is necessary at light loads, consider this
power loss when deciding whether to use DCR sensing
or sense resistors. Light load power loss can be modestly higher with a DCR network than with a sense resistor, due to the extra switching losses incurred through
R1. However, DCR sensing eliminates a sense resistor,
reduces conduction losses and provides higher efficiency
at heavy loads. Peak efficiency is about the same with
either method.
Inductor Value Calculation
The operating frequency and inductor selection are interrelated in that higher operating frequencies allow the use
of smaller inductor and capacitor values. So why would
anyone ever choose to operate at lower frequencies with
larger components? The answer is efficiency. A higher
frequency generally results in lower efficiency because
of MOSFET gate charge losses. In addition to this basic
trade-off, the effect of inductor value on ripple current and
low current operation must also be considered.
The inductor value has a direct effect on ripple current.
The inductor ripple current ∆IL decreases with higher
⎛ V ⎞
1
VOUT ⎜ 1− OUT ⎟
(f)(L)
VIN ⎠
⎝
For the boost controller, the inductor ripple current ∆IL
increases with higher VOUT:
ΔIL =
R1
For the boost controller, the maximum power loss in R1
will occur in continuous mode at VIN = 1/2•VOUT :
PLOSS R1=
ΔIL =
⎛
1
V ⎞
VIN ⎜ 1− IN ⎟
(f)(L) ⎝ VOUT ⎠
Accepting larger values of ∆IL allows the use of low inductances, but results in higher output voltage ripple and
greater core losses. A reasonable starting point for setting ripple current is ∆IL = 0.3(IMAX). The maximum ∆IL
occurs at the maximum input voltage for the bucks and
VIN = 1/2•VOUT for the boost.
The inductor value also has secondary effects. The transition to Burst Mode operation begins when the average
inductor current required results in a peak current below
25% of the current limit (30% for the boost) determined
by RSENSE. Lower inductor values (higher ∆IL) will cause
this to occur at lower load currents, which can cause a dip
in efficiency in the upper range of low current operation.
In Burst Mode operation, lower inductance values will
cause the burst frequency to decrease.
Inductor Core Selection
Once the value for L is known, the type of inductor must
be selected. High efficiency converters generally cannot
afford the core loss found in low cost powdered iron cores,
forcing the use of more expensive ferrite or molypermalloy cores. Actual core loss is independent of core size for
a fixed inductor value, but it is very dependent on inductance selected. As inductance increases, core losses go
down. Unfortunately, increased inductance requires more
turns of wire and therefore copper losses will increase.
Ferrite designs have very low core loss and are preferred
at high switching frequencies, so design goals can concentrate on copper loss and preventing saturation. Ferrite
7815f
For more information www.linear.com/LTC7815
21
LTC7815
APPLICATIONS INFORMATION
core material saturates “hard,” which means that inductance collapses abruptly when the peak design current is
exceeded. This results in an abrupt increase in inductor
ripple current and consequent output voltage ripple. Do
not allow the core to saturate!
The MOSFET power dissipations at maximum output current are given by:
PMAIN_BUCK =
The peak-to-peak drive levels are set by the INTVCC
voltage. This voltage is typically 5.4V during start-up
(see EXTVCC Pin Connection). Consequently, logic-level
threshold MOSFETs must be used in most applications.
Pay close attention to the BVDSS specification for the
MOSFETs as well; many of the logic level MOSFETs are
limited to 30V or less.
Selection criteria for the power MOSFETs include the
on-resistance RDS(ON), Miller capacitance CMILLER, input
voltage and maximum output current. Miller capacitance,
CMILLER, can be approximated from the gate charge curve
usually provided on the MOSFET manufacturers’ data
sheet. CMILLER is equal to the increase in gate charge
along the horizontal axis while the curve is approximately
flat divided by the specified change in VDS. This result is
then multiplied by the ratio of the application applied VDS
to the gate charge curve specified VDS. When the IC is
operating in continuous mode the duty cycles for the top
and bottom MOSFETs are given by:
Buck Main Switch Duty Cycle =
VOUT
VIN
Buck Sync Switch Duty Cycle =
VIN − VOUT
VIN
Boost Main Switch Duty Cycle =
VOUT − VIN
VOUT
Boost Sync Switch Duty Cycle =
VIN
VOUT
) (1+ δ )RDS(ON) +
2
⎛ IOUT(MAX) ⎞
(VIN )2 ⎜
⎟⎠ (RDR )(CMILLER ) •
2
⎝
Power MOSFET and Schottky Diode
(Optional) Selection
Two external power MOSFETs must be selected for each
controller in the LTC7815: one N-channel MOSFET for the
top switch (main switch for the buck, synchronous for the
boost), and one N-channel MOSFET for the bottom switch
(main switch for the boost, synchronous for the buck).
(
VOUT
I
VIN OUT(MAX)
⎡
1
1 ⎤
+
⎢V
⎥ (f)
⎣ INTVCC − VTHMIN VTHMIN ⎦
V −V
PSYNC_BUCK = IN OUT IOUT(MAX)
VIN
(
PMAIN_BOOST =
( VOUT − VIN ) VOUT
VIN
⎛V
(1+ δ )RDS(ON) + ⎜
3
OUT
⎝ VIN
2
) (1+ δ )RDS(ON)
2
(IOUT(MAX) )
2
•
⎞ ⎛ IOUT(MAX) ⎞
⎟⎜
⎟⎠ •
2
⎠⎝
⎡
1
1 ⎤
+
⎥ (f)
⎣ INTVCC − VTHMIN VTHMIN ⎦
2
V
= IN IOUT(MAX) (1+ δ )RDS(ON)
VOUT
(RDR )(CMILLER ) • ⎢ V
PSYNC_BOOST
(
)
where z is the temperature dependency of RDS(ON) and
RDR (approximately 2Ω) is the effective driver resistance
at the MOSFET’s Miller threshold voltage. VTHMIN is the
typical MOSFET minimum threshold voltage.
Both MOSFETs have I2R losses while the main N-channel
equations for the buck and boost controllers include an
additional term for transition losses, which are highest
at high input voltages for the bucks and low input voltages for the boost. For VIN < 20V (high VIN for the boost)
the high current efficiency generally improves with larger
MOSFETs, while for VIN > 20V (low VIN for the boost) the
transition losses rapidly increase to the point that the use
of a higher RDS(ON) device with lower CMILLER actually
7815f
22
For more information www.linear.com/LTC7815
LTC7815
APPLICATIONS INFORMATION
provides higher efficiency. The synchronous MOSFET
losses for the buck controllers are greatest at high input
voltage when the top switch duty factor is low or during a
short-circuit when the synchronous switch is on close to
100% of the period. The synchronous MOSFET losses for
the boost controller are greatest when the input voltage
approaches the output voltage or during an overvoltage
event when the synchronous switch is on 100% of the
period.
The term (1+ z) is generally given for a MOSFET in the
form of a normalized RDS(ON) vs Temperature curve, but
z = 0.005/°C can be used as an approximation for low
voltage MOSFETs.
A Schottky diode can be inserted in parallel with the
synchronous MOSFET to conduct during the dead-time
between the conduction of the two power MOSFETs. This
prevents the body diode of the synchronous MOSFET
from turning on, storing charge during the dead-time and
requiring a reverse recovery period that could cost as
much as 3% in efficiency at high VIN. A 1A to 3A Schottky
is generally a good compromise for both regions of operation due to the relatively small average current. Larger
diodes result in additional transition losses due to their
larger junction capacitance.
Boost CIN, COUT Selection
The input ripple current in a boost converter is relatively
low (compared with the output ripple current), because
this current is continuous. The boost input capacitor CIN
voltage rating should comfortably exceed the maximum
input voltage. Although ceramic capacitors can be relatively tolerant of overvoltage conditions, aluminum electrolytic capacitors are not. Be sure to characterize the
input voltage for any possible overvoltage transients that
could apply excess stress to the input capacitors.
The value of CIN is a function of the source impedance, and
in general, the higher the source impedance, the higher
the required input capacitance. The required amount of
input capacitance is also greatly affected by the duty cycle.
High output current applications that also experience high
duty cycles can place great demands on the input supply,
both in terms of DC current and ripple current.
In a boost converter, the output has a discontinuous current, so COUT must be capable of reducing the output
voltage ripple. The effects of ESR (equivalent series resistance) and the bulk capacitance must be considered when
choosing the right capacitor for a given output ripple voltage. The steady ripple due to charging and discharging
the bulk capacitance is given by:
Ripple =
(
IOUT(MAX) • VOUT − VIN(MIN)
COUT • VOUT • f
)V
where COUT is the output filter capacitor.
The steady ripple due to the voltage drop across the ESR
is given by:
∆VESR = IL(MAX) • ESR
Multiple capacitors placed in parallel may be needed to
meet the ESR and RMS current handling requirements.
Dry tantalum, special polymer, aluminum electrolytic and
ceramic capacitors are all available in surface mount
packages. Ceramic capacitors have excellent low ESR
characteristics but can have a high voltage coefficient.
Capacitors are now available with low ESR and high ripple
current ratings such as OS-CON and POSCAP.
Buck CIN, COUT Selection
The selection of CIN for the two buck controllers is simplified by the 2-phase architecture and its impact on the
worst-case RMS current drawn through the input network (battery/fuse/capacitor). It can be shown that the
worst-case capacitor RMS current occurs when only one
controller is operating. The controller with the highest
(VOUT)(IOUT) product needs to be used in the formula
shown in Equation (1) to determine the maximum RMS
capacitor current requirement. Increasing the output current drawn from the other controller will actually decrease
the input RMS ripple current from its maximum value.
The out-of-phase technique typically reduces the input
7815f
For more information www.linear.com/LTC7815
23
LTC7815
APPLICATIONS INFORMATION
capacitor’s RMS ripple current by a factor of 30% to 70%
when compared to a single phase power supply solution.
In continuous mode, the source current of the top MOSFET
is a square wave of duty cycle (VOUT)/(VIN). To prevent
large voltage transients, a low ESR capacitor sized for the
maximum RMS current of one channel must be used. The
maximum RMS capacitor current is given by:
CIN Required IRMS ≈
IMAX
VIN
1/2
⎡⎣( VOUT ) ( VIN − VOUT ) ⎤⎦
(1)
This formula has a maximum at VIN = 2VOUT, where IRMS
= IOUT/2. This simple worst-case condition is commonly
used for design because even significant deviations do
not offer much relief. Note that capacitor manufacturers’
ripple current ratings are often based on only 2000 hours
of life. This makes it advisable to further derate the capacitor, or to choose a capacitor rated at a higher temperature
than required. Several capacitors may be paralleled to
meet size or height requirements in the design. Due to
the high operating frequency of the LTC7815, ceramic
capacitors can also be used for CIN. Always consult the
manufacturer if there is any question.
The benefit of the LTC7815 2-phase operation can be
calculated by using Equation (1) for the higher power
controller and then calculating the loss that would have
resulted if both controller channels switched on at the
same time. The total RMS power lost is lower when both
controllers are operating due to the reduced overlap of
current pulses required through the input capacitor’s
ESR. This is why the input capacitor’s requirement calculated above for the worst-case controller is adequate
for the dual controller design. Also, the input protection
fuse resistance, battery resistance, and PC board trace
resistance losses are also reduced due to the reduced
peak currents in a 2-phase system. The overall benefit of
a multiphase design will only be fully realized when the
source impedance of the power supply/battery is included
in the efficiency testing. The drains of the top MOSFETs
should be placed within 1cm of each other and share a
common CIN (s). Separating the drains and CIN may produce undesirable voltage and current resonances at VIN.
A small (0.1µF to 1µF) bypass capacitor between the chip
VIN pin and ground, placed close to the LTC7815, is also
suggested. A small (1Ω to 10Ω) resistor placed between
CIN (C1) and the VIN pin provides further isolation between
the two channels.
The selection of COUT is driven by the effective series
resistance (ESR). Typically, once the ESR requirement
is satisfied, the capacitance is adequate for filtering. The
output ripple (∆VOUT) is approximated by:
⎛
1 ⎞
ΔVOUT ≈ ΔIL ⎜ ESR +
8fCOUT ⎟⎠
⎝
where f is the operating frequency, COUT is the output
capacitance and ∆IL is the ripple current in the inductor.
The output ripple is highest at maximum input voltage
since ∆IL increases with input voltage.
Setting Output Voltage
The LTC7815 output voltages are each set by an external
feedback resistor divider carefully placed across the output, as shown in Figure 3. The regulated output voltages
are determined by:
⎛ R ⎞
VOUT, BUCK = 0.8V ⎜ 1+ B ⎟
⎝ RA ⎠
⎛ R ⎞
VOUT, BOOST = 1.2V ⎜ 1+ B ⎟
⎝ RA ⎠
To improve the frequency response, a feedforward capacitor, CFF, may be used. Great care should be taken to route
the VFB line away from noise sources, such as the inductor
or the SW line.
VOUT
1/3 LTC7815
RB
CFF
VFB
RA
7815 F03
Figure 3. Setting Output Voltage
7815f
24
For more information www.linear.com/LTC7815
LTC7815
APPLICATIONS INFORMATION
Tracking and Soft-Start
(TRACK/SS1, TRACK/SS2, SS3 Pins)
1/3 LTC7815
TRACK/SS
tSS _ BUCK = CSS •
0.8V
5µA
tSS _ BOOST = CSS •
VOUT
=
7815 F04
Figure 4. Using the TRACK/SS Pin to Program Soft-Start
VX(MASTER)
VOUT(SLAVE)
TIME
7815 F05a
5a. Coincident Tracking
VX(MASTER)
VOUT(SLAVE)
1.2V
5µA
TIME
Alternatively, the TRACK/SS1 and TRACK/SS2 pins for the
two buck controllers can be used to track two (or more) supplies during start-up, as shown qualitatively in Figures 5a
and 5b. To do this, a resistor divider should be connected
from the master supply (VX) to the TRACK/SS pin of the
slave supply (VOUT), as shown in Figure 6. During start-up
VOUT will track VX according to the ratio set by the resistor divider:
VX
SGND
OUTPUT (VOUT)
Soft-start is enabled by simply connecting a capacitor
from the TRACK/SS pin to ground, as shown in Figure 4.
An internal 5µA current source charges the capacitor,
providing a linear ramping voltage at the TRACK/SS pin.
The LTC7815 will regulate the VFB pin (and hence VOUT)
according to the voltage on the TRACK/SS pin, allowing
VOUT to rise smoothly from 0V to its final regulated value.
The total soft-start time will be approximately:
CSS
OUTPUT (VOUT)
The start-up of each VOUT is controlled by the voltage on
the respective TRACK/SS pin (TRACK/SS1 for channel 1,
TRACK/SS2 for channel 2, SS3 for channel 3). When the
voltage on the TRACK/SS pin is less than the internal
0.8V reference (1.2V reference for the boost channel),
the LTC7815 regulates the VFB pin voltage to the voltage
on the TRACK/SS pin instead of the internal reference.
Likewise, the TRACK/SS pin for the buck channels can be
used to program an external soft-start function or to allow
VOUT to track another supply during start-up.
7815 F05b
5b. Ratiometric Tracking
Figure 5. Two Different Modes of Output Voltage Tracking
VOUT
RB
LTC7815
VFB1,2
+ R TRACKB
R
• TRACKA
R TRACKA
R A + RB
RA
VX
RA
RTRACKB
For coincident tracking (VOUT = VX during start-up),
TRACK/SS1,2
RA = RTRACKA
RTRACKA
RB = RTRACKB
7815 F06
Figure 6. Using the TRACK/SS Pin for Tracking
7815f
For more information www.linear.com/LTC7815
25
LTC7815
APPLICATIONS INFORMATION
INTVCC Regulators
The LTC7815 features two separate internal P-channel
low dropout linear regulators (LDO) that supply power
at the INTVCC pin from either the VBIAS supply pin or
the EXTVCC pin depending on the connection of the
EXTVCC pin. INTVCC powers the gate drivers and much
of the LTC7815’s internal circuitry. The VBIAS LDO and
the EXTVCC LDO regulate INTVCC to 5.4V. Each of these
must be bypassed to ground with a minimum of 4.7µF
ceramic capacitor. No matter what type of bulk capacitor is
used, an additional 1µF ceramic capacitor placed directly
adjacent to the INTVCC and PGND IC pins is highly recommended. Good bypassing is needed to supply the high
transient currents required by the MOSFET gate drivers
and to prevent interaction between the channels.
High input voltage applications in which large MOSFETs
are being driven at high frequencies may cause the maximum junction temperature rating for the LTC7815 to be
exceeded. The INTVCC current, which is dominated by the
gate charge current, may be supplied by either the VBIAS
LDO or the EXTVCC LDO. When the voltage on the EXTVCC
pin is less than 4.7V, the VBIAS LDO is enabled. Power
dissipation for the IC in this case is highest and is equal to
VBIAS • IINTVCC. The gate charge current is dependent
on operating frequency as discussed in the Efficiency
Considerations section. The junction temperature can
be estimated by using the equations given in Note 2 of
the Electrical Characteristics. For example, the LTC7815
INTVCC current is limited to less than 40mA from a 40V
supply when not using the EXTVCC supply at a 70°C ambient temperature:
TJ = 70°C + (40mA)(40V)(34.7°C/W) = 125°C
To prevent the maximum junction temperature from being
exceeded, the input supply current must be checked while
operating in continuous conduction mode (PLLIN/MODE
= INTVCC) at maximum VIN.
When the voltage applied to EXTVCC rises above 4.7V, the
VBIAS LDO is turned off and the EXTVCC LDO is enabled.
The EXTVCC LDO remains on as long as the voltage applied
to EXTVCC remains above 4.5V. The EXTVCC LDO attempts
to regulate the INTVCC voltage to 5.4V, so while EXTVCC
is less than 5.4V, the LDO is in dropout and the INTVCC
voltage is approximately equal to EXTVCC. When EXTVCC
is greater than 5.4V, up to an absolute maximum of 14V,
INTVCC is regulated to 5.4V.
Using the EXTVCC LDO allows the MOSFET driver and
control power to be derived from one of the LTC7815’s
switching regulator outputs (4.7V ≤ VOUT ≤ 14V) during
normal operation and from the VBIAS LDO when the output
is out of regulation (e.g., start-up, short-circuit). If more
current is required through the EXTVCC LDO than is specified, an external Schottky diode can be added between the
EXTVCC and INTVCC pins. In this case, do not apply more
than 6V to the EXTVCC pin and make sure that EXTVCC ≤
VBIAS.
Significant efficiency and thermal gains can be realized
by powering INTVCC from the buck output, since the VIN
current resulting from the driver and control currents will
be scaled by a factor of (Duty Cycle)/(Switcher Efficiency).
For 5V to 14V regulator outputs, this means connecting
the EXTVCC pin directly to VOUT. Tying the EXTVCC pin to
a 8.5V supply reduces the junction temperature in the
previous example from 125°C to:
TJ = 70°C + (40mA)(8.5V)(34.7°C/W) = 82°C
However, for 3.3V and other low voltage outputs, additional circuitry is required to derive INTVCC power from
the output.
The following list summarizes the three possible connections for EXTVCC:
1. EXTVCC grounded. This will cause INTVCC to be powered from the internal 5.4V regulator resulting in an
efficiency penalty of up to 10% at high input voltages.
2. EXTVCC connected directly to the output voltage of one
of the buck regulators. This is the normal connection
for a 5V to 14V regulator and provides the highest
efficiency.
3. EXTVCC connected to an external supply. If an external supply is available in the 5V to 14V range, it may
be used to power EXTVCC providing it is compatible
with the MOSFET gate drive requirements. Ensure that
EXTVCC ≤ VBIAS.
7815f
26
For more information www.linear.com/LTC7815
LTC7815
APPLICATIONS INFORMATION
Topside MOSFET Driver Supply (CB, DB)
External bootstrap capacitors CB connected to the
BOOST pins supply the gate drive voltages for the topside MOSFETs. Capacitor CB in the Functional Diagram is
charged though external diode DB from INTVCC when the
SW pin is low. When one of the topside MOSFETs is to
be turned on, the driver places the CB voltage across the
gate-source of the desired MOSFET. This enhances the
MOSFET and turns on the topside switch. The switch node
voltage, SW, rises to VIN for the buck channels (VOUT for
the boost channel) and the BOOST pin follows. With the
topside MOSFET on, the boost voltage is above the input
supply: VBOOST = VIN + VINTVCC (VBOOST = VOUT + VINTVCC
for the boost controller). The value of the boost capacitor
CB needs to be 100 times that of the total input capacitance
of the topside MOSFET(s). The reverse breakdown of the
external Schottky diode must be greater than VIN(MAX) for
the buck channels and VOUT(MAX) for the boost channel.
The external diode DB can be a Schottky diode or silicon
diode, but in either case it should have low leakage and
fast recovery. Pay close attention to the reverse leakage at high temperatures where it generally increases
substantially.
The topside MOSFET driver for the boost channel includes
an internal charge pump that delivers current to the bootstrap capacitor from the BOOST3 pin. This charge current maintains the bias voltage required to keep the top
MOSFET on continuously during dropout/overvoltage
conditions. The Schottky/silicon diode selected for the
boost topside driver should have a reverse leakage less
than the available output current the charge pump can
supply. Curves displaying the available charge pump current under different operating conditions can be found in
the Typical Performance Characteristics section.
A leaky diode DB in the boost converter can not only prevent the top MOSFET from fully turning on but it can also
completely discharge the bootstrap capacitor CB and create a current path from the input voltage to the BOOST3
pin to INTVCC. This can cause INTVCC to rise if the diode
leakage exceeds the current consumption on INTVCC .
This is particularly a concern in Burst Mode operation
where the load on INTVCC can be very small. There is
an internal voltage clamp on INTVCC that prevents the
INTVCC voltage from running away, but this clamp should
be regarded as a failsafe only. The external Schottky or
silicon diode should be carefully chosen such that INTVCC
never gets charged up much higher than its normal regulation voltage.
Care should also be taken when choosing the external
diode DB for the buck converters. A leaky diode not only
increases the quiescent current of the buck converter, but
it can also cause a similar leakage path to INTVCC from
VOUT for applications with output voltages greater than
the INTVCC voltage (~5.4V).
Fault Conditions: Buck Current Limit and Current
Foldback
The LTC7815 includes current foldback for the buck
channels to help limit load current when the output is
shorted to ground. If the buck output falls below 70% of
its nominal output level, then the maximum sense voltage is progressively lowered from 100% to 40% of its
maximum selected value. Under short-circuit conditions
with very low duty cycles, the buck channel will begin
cycle skipping in order to limit the short-circuit current.
In this situation the bottom MOSFET will be dissipating
most of the power but less than in normal operation. The
short-circuit ripple current is determined by the minimum
on-time tON(MIN) of the LTC7815 (≈40ns), the input voltage and inductor value:
∆IL(SC) = tON(MIN) (VIN/L)
The resulting average short-circuit current is:
1
I = 40% •I
LIM(MAX) − ΔIL(SC)
SC
2
Fault Conditions: Buck Overvoltage Protection (Crowbar)
The overvoltage crowbar is designed to blow a system
input fuse when the output voltage of the one of the buck
regulators rises much higher than nominal levels. The
crowbar causes huge currents to flow, that blow the fuse
to protect against a shorted top MOSFET if the short
occurs while the controller is operating.
A comparator monitors the buck output for overvoltage
conditions. The comparator detects faults greater than
10% above the nominal output voltage. When this condition is sensed, the top MOSFET of the buck controller is
For more information www.linear.com/LTC7815
7815f
27
LTC7815
APPLICATIONS INFORMATION
turned off and the bottom MOSFET is turned on until the
overvoltage condition is cleared. The bottom MOSFET
remains on continuously for as long as the overvoltage
condition persists; if VOUT returns to a safe level, normal
operation automatically resumes.
A shorted top MOSFET for the buck channel will result in
a high current condition which will open the system fuse.
The switching regulator will regulate properly with a leaky
top MOSFET by altering the duty cycle to accommodate
the leakage.
Fault Conditions: Over Temperature Protection
At higher temperatures, or in cases where the internal
power dissipation causes excessive self heating on chip
(such as INTVCC short to ground), the over temperature
shutdown circuitry will shut down the LTC7815. When the
junction temperature exceeds approximately 170°C, the
over temperature circuitry disables the INTVCC LDO, causing the INTVCC supply to collapse and effectively shutting
down the entire LTC7815 chip. Once the junction temperature drops back to approximately 155°C, the INTVCC
LDO turns back on. Long term overstress (TJ > 125°C)
should be avoided as it can degrade the performance or
shorten the life of the part.
Frequency Synchronization and Selection
The LTC7815 has an internal phase-locked loop (PLL)
comprised of a phase frequency detector, a lowpass filter,
and a voltage-controlled oscillator (VCO). This allows the
turn-on of the top MOSFET of controller 1 to be locked
to the rising edge of an external clock signal applied to
the PLLIN/MODE pin. The turn-on of controller 2’s top
MOSFET is thus 180 degrees out of phase with the external clock. The phase detector is an edge sensitive digital
type that provides zero degrees phase shift between the
external and internal oscillators. This type of phase detector does not exhibit false lock to harmonics of the external
clock.
If the external clock frequency is greater than the internal
oscillator’s frequency, fOSC, then current is sourced continuously from the phase detector output, pulling up the
VCO input. When the external clock frequency is less than
fOSC, current is sunk continuously, pulling down the VCO
input. If the external and internal frequencies are the same
but exhibit a phase difference, the current sources turn
on for an amount of time corresponding to the phase difference. The voltage at the VCO input is adjusted until the
phase and frequency of the internal and external oscillators are identical. At the stable operating point, the phase
detector output is high impedance and the internal filter
capacitor, CLP, holds the voltage at the VCO input.
Note that the LTC7815 can only be synchronized to an
external clock whose frequency is within range of the
LTC7815’s internal VCO, which is guaranteed to be
between 0.32MHz to 2.25MHz.
Typically, the external clock (on PLLIN/MODE pin) input
high threshold is 1.6V, while the input low threshold is
1.1V. The LTC7815 is guaranteed to synchronize to an
external clock that swings up to at least 2.5V and down
to 0.5V or less.
Rapid phase-locking can be achieved by using the FREQ
pin to set a free-running frequency near the desired synchronization frequency. The VCO’s input voltage is prebiased at a frequency correspond to the frequency set by the
FREQ pin. Once prebiased, the PLL only needs to adjust
the frequency slightly to achieve phase-lock and synchronization. Although it is not required that the free-running
frequency be near external clock frequency, doing so will
prevent the operating frequency from passing through a
large range of frequencies as the PLL locks.
If the PLLIN/MODE pin is not being driven by an external
clock source, the FREQ pin can be tied to SGND, tied
to INTVCC or programmed through an external resistor.
Tying FREQ to SGND selects 0.94MHz while tying FREQ
7815f
28
For more information www.linear.com/LTC7815
LTC7815
APPLICATIONS INFORMATION
If the duty cycle falls below what can be accommodated
by the minimum on-time, the controller will begin to skip
cycles. The output voltage will continue to be regulated,
but the ripple voltage and current will increase.
2250
2000
FREQUENCY (kHz)
1750
1500
1250
1000
750
500
250
25
35
45
55
65
75
85
95
105
FREQ PIN RESISTOR (kΩ)
7815 F07
Figure 7. Relationship Between Oscillator
Frequency and Resistor Value at the FREQ Pin
The minimum on-time for the LTC7815 is approximately
45ns for the bucks and 70ns for the boost. However, as
the peak sense voltage decreases the minimum on-time
for the bucks gradually increases up to about 70ns. This
is of particular concern in forced continuous applications
with low ripple current at light loads. If the duty cycle
drops below the minimum on-time limit in this situation,
a significant amount of cycle skipping can occur with correspondingly larger current and voltage ripple.
Efficiency Considerations
to INTVCC selects 1.44MHz. Placing a resistor between
FREQ and SGND allows the frequency to be programmed
between 320kHz and 2.25MHz, as shown in Figure 7.
Table 1 summarizes the different states in which the FREQ
pin can be used.
Table 1
FREQ PIN
PLLIN/MODE PIN
FREQUENCY
0V
DC Voltage
0.94MHz
INTVCC
DC Voltage
1.44MHz
Resistor to SGND
DC Voltage
0.32MHz to 2.25MHz
Any of the Above
External Clock
Phase-Locked to
External Clock
Minimum On-Time Considerations
Minimum on-time tON(MIN) is the smallest time duration that the LTC7815 is capable of turning on the top
MOSFET (bottom MOSFET for the boost controller). It is
determined by internal timing delays and the gate charge
required to turn on the top MOSFET. Low duty cycle applications may approach this minimum on-time limit and
care should be taken to ensure that
tON(MIN)_BUCK <
VOUT
VIN(f)
tON(MIN)_BOOST <
VOUT − VIN
VOUT (f)
The percent efficiency of a switching regulator is equal to
the output power divided by the input power times 100%.
It is often useful to analyze individual losses to determine
what is limiting the efficiency and which change would
produce the most improvement. Percent efficiency can
be expressed as:
%Efficiency = 100% – (L1 + L2 + L3 + ...)
where L1, L2, etc. are the individual losses as a percentage of input power.
Although all dissipative elements in the circuit produce
losses, four main sources usually account for most of the
losses in LTC7815 circuits: 1) IC VBIAS current, 2) INTVCC
regulator current, 3) I2R losses, 4) Topside MOSFET transition losses.
1. The VBIAS current is the DC supply current given in
the Electrical Characteristics table, which excludes
MOSFET driver and control currents. VBIAS current
typically results in a small (1µF) supply bypass capacitors. The
discharged bypass capacitors are effectively put in parallel
with COUT, causing a rapid drop in VOUT. No regulator can
alter its delivery of current quickly enough to prevent this
sudden step change in output voltage if the load switch
resistance is low and it is driven quickly. If the ratio of
CLOAD to COUT is greater than 1:50, the switch rise time
should be controlled so that the load rise time is limited
to approximately 25 • CLOAD. Thus a 10µF capacitor would
require a 250µs rise time, limiting the charging current
to about 200mA.
Buck Design Example
As a design example for one of the buck channels, assume
VIN = 12V(NOMINAL), VIN = 22V(MAX), VOUT = 3.3V, IMAX =
5A, VSENSE(MAX) = 50mV, and f = 1MHz.
The inductance value is chosen first based on a 30% ripple current assumption. The highest value of ripple current occurs at the maximum input voltage. Tie the FREQ
pin with 54.9k resistor to GND, generating approximately
1MHz operation. The inductor ripple current can be calculated from the following equation:
ΔIL =
⎞
VOUT ⎛
VOUT
1−
⎜
(f)(L) ⎝ VIN(NOMINAL) ⎟⎠
A 1.5µH inductor will produce 32% ripple current. The
peak inductor current will be the maximum DC value plus
one half the ripple current, or 5.8A. Increasing the ripple
current will also help ensure that the minimum on-time
of 45ns is not violated. The minimum on-time occurs at
maximum VIN:
tON(MIN) =
VOUT
VIN(MAX)(f)
=
3.3V
22V(1MHz)
= 150ns
The RSENSE resistor value can be calculated by using the
minimum value for the maximum current sense threshold
(43mV):
RSENSE ≤
43mV
= 0.007Ω
5.8A
Choosing 1% resistors: RA = 25k and RB = 80.6k yields
an output voltage of 3.38V.
The power dissipation on the top side MOSFET can be
easily estimated. Choosing a Infineon BSZ097N04LSG
MOSFET results in: RDS(ON) = 11.4mΩ, CMILLER = 16pF.
At maximum input voltage with T(estimated) = 50°C:
3.3V
(5A)2 {1+ (0.005)(50°C − 25°C)}
22V
5A
(11.4mΩ) + (22V)2 (2.5Ω)(16pF) •
2
1
1
⎧
⎫
+
⎨
⎬(1MHz) = 94mW
⎩ 5V − 1.5V 1.5V ⎭
(22V – 3.3V ) (5A)2(1.125)(11.4mΩ) = 273mW
PSYNC =
22V
PMAIN =
7815f
For more information www.linear.com/LTC7815
31
LTC7815
APPLICATIONS INFORMATION
A short-circuit to ground will result in a folded back current of:
ISC =
20 mV 1 ⎧ 40ns(22V) ⎫
− ⎨
⎬ = 2.56A
0.007Ω 2 ⎩ 1.5µH ⎭
with a typical value of RDS(ON) and z = (0.005/°C)(25°C)
= 0.125. The resulting power dissipated in the bottom
MOSFET is:
PSYNC,SC = (2.56A)2(1.125)(11.4mΩ) = 84mW
The input capacitor to the buck regulator CIN is chosen for
an RMS current rating of at least 3A at temperature. COUT
is chosen with an ESR of 0.02Ω for low output ripple. The
output ripple in continuous mode will be highest at the
maximum input voltage. The output voltage ripple due to
ESR is approximately:
VORIPPLE = RESR (∆IL) = 0.02Ω(1.6A) = 32mVP-P
PC Board Layout Checklist
When laying out the printed circuit board, the following
checklist should be used to ensure proper operation of
the IC. Figure 8 illustrates the current waveforms present
in the various branches of the 2-phase synchronous buck
regulators operating in the continuous mode. Check the
following in your layout:
1. Are the top N-channel MOSFETs MTOP1 and MTOP2
located within 1cm of each other with a common drain
connection at CIN? Do not attempt to split the input
decoupling for the two channels as it can cause a large
resonant loop.
2. Are the signal and power grounds kept separate? The
combined IC signal ground pin and the ground return
of CINTVCC must return to the combined COUT (–) terminals. The path formed by the top N-channel MOSFET,
Schottky diode and the CIN capacitor should have short
leads and PC trace lengths. The output capacitor (–)
terminals should be connected as close as possible
to the (–) terminals of the input capacitor by placing
the capacitors next to each other and away from the
Schottky loop described above.
3. Do the LTC7815 VFB pins’ resistive dividers connect to
the (+) terminals of COUT? The resistive divider must be
connected between the (+) terminal of COUT and signal
ground. The feedback resistor connections should not
be along the high current input feeds from the input
capacitor(s).
4. Are the SENSE– and SENSE+ leads routed together
with minimum PC trace spacing? The filter capacitor
between SENSE+ and SENSE– should be as close as
possible to the IC. Ensure accurate current sensing
with Kelvin connections at the sense resistor.
5. Is the INTVCC decoupling capacitor connected close
to the IC, between the INTVCC and the power ground
pins? This capacitor carries the MOSFET drivers’ current peaks. An additional 1µF ceramic capacitor placed
immediately next to the INTVCC and PGND pins can
help improve noise performance substantially.
6. Keep the switching nodes (SW1, SW2, SW3), top gate
nodes (TG1, TG2, TG3), and boost nodes (BOOST1,
BOOST2, BOOST3) away from sensitive small-signal
nodes, especially from the opposites channel’s voltage
and current sensing feedback pins. All of these nodes
have very large and fast moving signals and therefore
should be kept on the output side of the LTC7815 and
occupy minimum PC trace area.
7. Use a modified star ground technique: a low impedance, large copper area central grounding point on the
same side of the PC board as the input and output
capacitors with tie-ins for the bottom of the INTVCC
decoupling capacitor, the bottom of the voltage feedback resistive divider and the SGND pin of the IC.
PC Board Layout Debugging
Start with one controller on at a time. It is helpful to use
a DC-50MHz current probe to monitor the current in
the inductor while testing the circuit. Monitor the output switching node (SW pin) to synchronize the oscilloscope to the internal oscillator and probe the actual output voltage as well. Check for proper performance over
the operating voltage and current range expected in the
7815f
32
For more information www.linear.com/LTC7815
LTC7815
APPLICATIONS INFORMATION
application. The frequency of operation should be maintained over the input voltage range down to dropout and
until the output load drops below the low current operation threshold—typically 25% of the maximum designed
current level in Burst Mode operation.
The duty cycle percentage should be maintained from
cycle to cycle in a well-designed, low noise PCB implementation. Variation in the duty cycle at a subharmonic
rate can suggest noise pickup at the current or voltage sensing inputs or inadequate loop compensation.
Overcompensation of the loop can be used to tame a
poor PC layout if regulator bandwidth optimization is not
required. Only after each controller is checked for its individual performance should both controllers be turned on
at the same time. A particularly difficult region of operation is when one controller channel is nearing its current
comparator trip point when the other channel is turning
on its top MOSFET. This occurs around 50% duty cycle
on either channel due to the phasing of the internal clocks
and may cause minor duty cycle jitter.
Reduce VIN from its nominal level to verify operation
of the regulator in dropout. Check the operation of the
undervoltage lockout circuit by further lowering VIN while
monitoring the outputs to verify operation.
Investigate whether any problems exist only at higher output currents or only at higher input voltages. If problems
coincide with high input voltages and low output currents,
look for capacitive coupling between the BOOST, SW, TG,
and possibly BG connections and the sensitive voltage
and current pins. The capacitor placed across the current
sensing pins needs to be placed immediately adjacent to
the pins of the IC. This capacitor helps to minimize the
effects of differential noise injection due to high frequency
capacitive coupling. If problems are encountered with
high current output loading at lower input voltages, look
for inductive coupling between CIN, Schottky and the top
MOSFET components to the sensitive current and voltage
sensing traces. In addition, investigate common ground
path voltage pickup between these components and the
SGND pin of the IC.
An embarrassing problem, which can be missed in an
otherwise properly working switching regulator, results
when the current sensing leads are hooked up backwards.
The output voltage under this improper hookup will still
be maintained but the advantages of current mode control
will not be realized. Compensation of the voltage loop
will be much more sensitive to component selection. This
behavior can be investigated by temporarily shorting out
the current sensing resistor—don’t worry, the regulator
will still maintain control of the output voltage.
7815f
For more information www.linear.com/LTC7815
33
LTC7815
APPLICATIONS INFORMATION
SW1
L1
D1
RSENSE1
VOUT1
COUT1
RL1
VIN
RIN
CIN
SW2
BOLD LINES INDICATE
HIGH SWITCHING
CURRENT. KEEP LINES
TO A MINIMUM LENGTH.
D2
L2
RSENSE2
VOUT2
COUT2
RL2
7815 F08
Figure 8. Branch Current Waveforms for Bucks
7815f
34
For more information www.linear.com/LTC7815
LTC7815
TYPICAL APPLICATIONS
VOUT1
10pF
68.1k
357k
82pF
820pF
LTC7815
SENSE1–
VFB1
1nF
SENSE1+
4.99k
ITH1
PGOOD1
0.1µF
INTVCC
10µF
FREQ
0.1µF
10pF
VOUT1
5V
7A
210k
COUT1
47µF
×2
MBOT1
BG1
68.1k
0.003Ω
SW1
BOOST1
VOUT2
L1
0.33µH
MTOP1
TG1
TRACK/SS1
100k
100k
100Ω
D1
VFB2
VBIAS
0.1µF
82pF
PGND
820pF
2.49k
ITH2
0.1µF
4.7µF
TRACK/SS2
INTVCC
10µF
D2
VOUT3
10pF
MTOP2
TG2
499k
68.1k
BOOST2
VFB3
0.1µF
0.003Ω
SW2
470pF
8.06k
ITH3
0.1µF
COUT2
33µF
×2
MBOT2
BG2
4.7nF
L2
0.33µH
VOUT2
3.3V
10A*
100Ω
SENSE2+
1nF
SS3
–
SENSE2
PLLINMODE
INTVCC
100k
VOUT1
D3
OV3
TG3
EXTVCC
SW3
RUN1
RUN2
RUN3
BOOST3
MTOP3
L3
0.16µH
0.003Ω
COUT3B
10µF
×3
+
0.1µF
MBOT3
BG3
SENSE3–
1nF
+
CINB
10µF
×2
COUT3A
68µF
CINA
220µF
VOUT3
10V
3A
VIN
2.5V TO 28V*
(START-UP ABOVE 5V)
100Ω
SENSE3+
7815 F09
MTOP1, 2: INFINEON BSZ097N04LS
MBOT1, 2: INFINEON BSZ097N04LS
MTOP3: INFINEON BSC027NO4LS
MBOT3: INFINEON BSC027NO4LS
L1: COILCRAFT XAL5030-331ME
L2: COILCRAFT XAL5030-331ME
L3: COILCRAFT XAL5030-161ME
CINA: SANYO 50CE220LX
CINB: TDK C3225X7R1H106M250AC
COUT1: TDK C3225X5R1A476M
COUT2: TDK C3225X5R1A336M200AC
COUT3A: SANYO 50SVPF68M
COUT3B: TDK C3225X7R1H106M250AC
D1, D2: CMDSH-4E
D3: BAS140W
* WHEN VIN < 3.5V, MAXIMUM LOAD
CURRENT AVAILABLE OF CH3 IS REDUCED
* VOUT3 IS 10V WHEN VIN < 10V
FOLLOWS VIN WHEN VIN > 10V
* OUTPUT CURRENT CAPABILITY
AT HIGH INPUT VOLTAGES MAY
BE LIMITED BY THE THERMAL
CHARACTERISTICS OF THE OVERALL
SYSTEM AND PRINTED CIRCUIT
BOARD DESIGN
Figure 9. High Efficiency Wide Input Range 2.1MHz Dual 5V/3.3V Regulator
7815f
For more information www.linear.com/LTC7815
35
LTC7815
TYPICAL APPLICATIONS
VOUT1
10pF
357k
68.1k
LTC7815
SENSE1–
VFB1
1nF
150pF
15k
1.2nF
0.1µF
40.2k
SENSE1+
ITH1
PGOOD1
100Ω
100k
INTVCC
TRACK/SS1
FREQ
10pF
COUT1B
22µF
0.1µF
BOOST1
649k
68.1k
0.1µF
VOUT3
10pF
PGND
4.7µF
ITH2
INTVCC
TRACK/SS2
COUT2B
10µF
0.1µF
100Ω
SENSE2+
D3
PLLIN/MODE
MTOP3
TG3
SW3
0.1µF
OV3
COUT3B
10µF
×3
L3
1.8µH
+
COUT3A
220µF
EXTVCC
BG3
RUN1
RUN2
SENSE3–
RUN3
VOUT3
18V
2A
0.004Ω
BOOST3
VOUT1
COUT2A
47µF
1nF
SENSE2–
SS3
100k
+
MBOT2
BG2
ITH3
VOUT2
8.5V
3A
0.008Ω
SW2
1nF
2.49k
L2
1.5µH
0.1µF
VFB3
INTVCC
MTOP2
TG2
BOOST2
453k
32.4k
10nF
10µF
D2
0.1µF
COUT1A
220µF
D1
100pF
10.5k
+
MBOT1
VOUT1
5V
5A
VBIAS
VFB2
1000pF
0.005Ω
SW1
BG1
VOUT2
10µF
L1
1.5µH
MTOP1
TG1
CINB
10µF
×2
MBOT3
100Ω
+
CINA
220µF
VIN
2.5V TO 38V
(START-UP ABOVE 5V)
1nF
SENSE3+
7815 F10
MTOP1, 2: INFINEON BSZ097NO4LS
MBOT1, 2: INFINEON BSZ097NO4LS
MTOP3: INFINEON BSC027NO4LS
MBOT3: INFINEON BSC027NO4LS
L1: WURTH 744314150
L2: WURTH 744314150
L3: WURTH 744325180
CINA: SANYO 50CE220LX
CINB: TDK C3225X7R1H106M250AC
COUT1A: PANASONIC 6TPF220M5L
COUT1B: TDK C3225X5R1A226M
COUT2A: PANASONIC 16TQC47MYFD
COUT2B: TDK CGA6M3X7R1C106M200AB
COUT3A: SANYO 50CE220LX
COUT3B: TDK C3225X7R1H106M250AC
D1, D2: CMDSH-4E
D3: BAS140W
* WHEN VIN < 4.5V, MAXIMUM LOAD CURRENT AVAILABLE OF CH3 IS REDUCED
VOUT3 IS 18V WHEN VIN < 18V
FOLLOWS VIN WHEN VIN > 18V
Figure 10. High Efficiency Wide Input Range 600kHz Triple 5V/8.5V/18V Regulator
7815f
36
For more information www.linear.com/LTC7815
LTC7815
PACKAGE DESCRIPTION
Please refer to http://www.linear.com/product/LTC7815#packaging for the most recent package drawings.
UHF Package
38-Lead Plastic QFN (5mm × 7mm)
(Reference LTC DWG # 05-08-1701 Rev C)
0.70 ±0.05
5.50 ±0.05
5.15 ±0.05
4.10 ±0.05
3.00 REF
3.15 ±0.05
PACKAGE
OUTLINE
0.25 ±0.05
0.50 BSC
5.5 REF
6.10 ±0.05
7.50 ±0.05
RECOMMENDED SOLDER PAD LAYOUT
APPLY SOLDER MASK TO AREAS THAT ARE NOT SOLDERED
5.00 ±0.10
0.75 ±0.05
PIN 1 NOTCH
R = 0.30 TYP OR
0.35 × 45° CHAMFER
3.00 REF
37
0.00 – 0.05
38
0.40 ±0.10
PIN 1
TOP MARK
(SEE NOTE 6)
1
2
5.15 ±0.10
5.50 REF
7.00 ±0.10
3.15 ±0.10
(UH) QFN REF C 1107
0.200 REF 0.25 ±0.05
0.50 BSC
R = 0.125
TYP
R = 0.10
TYP
BOTTOM VIEW—EXPOSED PAD
NOTE:
1. DRAWING CONFORMS TO JEDEC PACKAGE
OUTLINE M0-220 VARIATION WHKD
2. DRAWING NOT TO SCALE
3. ALL DIMENSIONS ARE IN MILLIMETERS
4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE
MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.20mm ON ANY SIDE
5. EXPOSED PAD SHALL BE SOLDER PLATED
6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION
ON THE TOP AND BOTTOM OF PACKAGE
7815f
Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog
Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications
subject to change without notice. No license
is granted
by implication
or otherwise under any patent or patent rights of Analog Devices.
For more
information
www.linear.com/LTC7815
37
LTC7815
TYPICAL APPLICATION
VOUT1
LTC7815
475k
10pF
34k
VFB1
SENSE1–
47pF
1nF
SENSE1+
3.01k
560pF
ITH1
0.1µF
TRACK/SS1
100k
FREQ
VOUT2
68.1k
10pF
ITH2
TRACK/SS2
BOOST1
COUT1
10µF
×2
MBOT1
D1
PGND
4.7µF
INTVCC
VFB3
150pF
10µF
TG2
787k
BOOST2
MTOP2
0.1µF
L2
1.0µH
0.007Ω
SW2
ITH3
0.1µF
100k
SS3
100Ω
SENSE2+
TG3
RUN1
RUN2
RUN3
SW3
VOUT2
8.5V
4A
1nF
PLLINMODE SENSE2–
EXTVCC
OV3
COUT2
10µF
×2
MBOT2
BG2
3.01k
MTOP1, 2: INFINEON BSZ097N04LS
MBOT1, 2: INFINEON BSZ097N04LS
INTVCC
MTOP3: INFINEON BSC027N04LS
MBOT3: INFINEON BSC027N04LS
L1: COILCRAFT XAL5030-102MEB
L2: COILCRAFT XAL5030-102MEB
L3: COILCRAFT XAL5030-331ME
CINA: SANYO 50CE220LX
CINB: TDK C3225X7R1H106M250AC
COUT1: TDK C3225X5R1E106M250AA
COUT2: TDK C3225X5R1C106M
COUT3A: SANYO 50SVPF68M
COUT3B: TDK C3225X7R1H106M250AC
D1, D2: CMDSH-4E
D3: BAS140W
VOUT1
12V
3A
0.1µF
D2
VOUT3
1.5nF
0.009Ω
0.1µF
5.1k
10pF
L1
1.0µH
SW1
VBIAS
0.1µF
68.1k
10µF
MTOP1
VFB2
47µF
INTVCC
TG1
BG1
649k
680pF
100k
PGOOD1
100Ω
D3
MTOP3
L3
0.33µH
0.003Ω
COUT3B
10µF
×3
+
0.1µF
CINB
10µF
×2
BOOST3
BG3
MBOT3
SENSE3–
SENSE3+
+
100Ω
1nF
COUT3A
68µF
CINA
220µF
VOUT3
15V
2A
VIN
2.5V TO 38V
(START-UP ABOVE 5V)
* WHEN VIN < 3.5, MAXIMUM LOAD CURRENT
AVAILABLE OF CH3 IS REDUCED
* VOUT3 IS 15V WHEN VIN < 15V
FOLLOWS VIN WHEN VIN > 15V
7815 F11
Figure 11. High Efficiency Wide Input Range 2.1MHz Dual 12V/8.5V Converter
RELATED PARTS
PART NUMBER
DESCRIPTION
COMMENTS
LTC3859AL
38V Triple Output, Buck/Buck/Boost Synchronous
Controller PLL Fixed Operating Frequency 50kHz to
900kHz
4.5V (Down to 2.5V After Start-Up) ≤ VIN ≤ 38V, IQ = 28μA Buck VOUT
Range: 0.8V to 24V, Boost VOUT Up to 60V
LTC7812
38V Synchronous Boost+Buck Controller Low EMI
and Low Input/Output Ripple
4.5V (Down to 2.5V After Start-Up) ≤ VIN ≤ 38V, Boost VOUT up to 60V,
Buck VOUT Range: 0.8V to 24V, IQ = 29μA, 5mm × 5mm QFN-32
LTC3857/LTC3857-1 38V Low IQ, Dual Output 2-Phase Synchronous
LTC3858/LTC3858-1 Step-Down Controller with 99% Duty Cycle
4V ≤ VIN ≤ 38V, 0.8V ≤ VOUT ≤ 24V, IQ = 50μA/170μA, PLL Fixed Operating
Frequency 50kHz to 900kHz
LTC7800
60V Low IQ, High Frequency Synchronous
Step-Down Controller
4V ≤ VIN ≤ 60V, 0.8V ≤ VOUT ≤ 24V, IQ = 50μA, PLL Fixed Frequency 320kHz
to 2.25MHz
LTC3899
60V Low IQ, Triple Output, Buck/Buck/Boost
Synchronous Controller
4.5V (Down to 2.2V After Start-Up) ≤ VIN ≤ 60V, IQ = 28μA, Buck and Boost
VOUT Up to 60V
LTC3897
65V Low IQ, Single Output 2-Phase Synchronous
Boost Controller with Input/Output Protection
4.5V ≤ VIN ≤ 65V, VOUT Up to 60V, IQ = 55μA, PLL Fixed Frequency 50kHZ to
900kHz
LTC3892
60V Low IQ, Dual 2-Phase Synchronous Step-Down 4.5V ≤ VIN ≤ 60V, 0.8V ≤ VOUT ≤ 0.99VIN, IQ = 50μA, PLL Fixed Frequency
Controller with Adjustable Gate Drive Voltage
50kHz to 900kHz
7815f
38
LT 0118 • PRINTED IN USA
www.linear.com/LTC7815
ANALOG DEVICES, INC. 2018
工商网监
湘ICP备2023018690号
