LTM4620
Dual 13A or Single 26A
DC/DC µModule Regulator
DESCRIPTION
FEATURES
n
n
n
n
n
n
n
n
n
n
n
n
n
n
n
Complete Standalone Dual Output Power Supply
Dual 13A or Single 26A Output
Wide Input Voltage Range: 4.5V to 16V
Output Voltage Range: 0.6V to 2.5V
±1.5% Maximum Total DC Output Error
Multiphase Current Sharing with Multiple
LTM4620s Up to 100A
Differential Remote Sense Amplifier
Current Mode Control/Fast Transient Response
Adjustable Switching Frequency
Overcurrent Foldback Protection
Frequency Synchronization
Internal Temperature Monitor
Output Overvoltage Protection
SnPb or RoHS Compliant Finish
Thermally Enhanced (15mm × 15mm × 4.41mm) LGA
Package and (15mm × 15mm × 5.01mm) BGA Package
APPLICATIONS
Telecom and Networking Equipment
Storage and ATCA Cards
n Industrial Equipment
n
n
The LTM®4620 is a complete dual 13A output switching
mode DC/DC power supply. Included in the package are
the switching controller, power FETs, inductors, and all
supporting components. Operating from an input voltage
range of 4.5V to 16V, the LTM4620 supports two outputs
each with an output voltage range of 0.6V to 2.5V, set by a
single external resistor. Its high efficiency design delivers
up to 13A continuous current for each output. Only a few
input and output capacitors are needed.
The device supports frequency synchronization, multiphase operation, Burst Mode operation and output voltage
tracking for supply rail sequencing and has an onboard
temperature diode for device temperature monitoring.
High switching frequency and a current mode architecture enable a very fast transient response to line and load
changes without sacrificing stability.
Fault protection features include overvoltage and
overcurrent protection. The power module is
offered in a proprietary space saving and thermally
enhanced 15mm × 15mm × 4.41mm LGA package and 15mm × 15mm × 5.01mm BGA package,
with integrated top-side heat sink. The LTM4620 is available with SnPb (BGA) or RoHS compliant terminal finish.
L, LT, LTC, LTM, Linear Technology, the Linear logo, µModule, Burst Mode, LTpowerCAD
and PolyPhase are registered trademarks of Analog Devices, Inc. All other trademarks are the
property of their respective owners.
Click to view associated TechClip Videos.
TYPICAL APPLICATION
26A, 1.2V Output DC/DC µModule® Regulator
INTVCC
4.7µF
1.2V Efficiency vs IOUT
5k
PGOOD
10k*
22µF
×4
25V
MODE_PLLIN CLKOUT INTVCC
VIN
EXTVCC PGOOD1
VOUT1
VOUTS1
120k
DIFFOUT
TEMP
VFB2
60.4k
COMP2
f SET
VOUT2
121k
SW2
GND
DIFFP
DIFFN
PGOOD2
70
60
50
VOUTS2
PHASMD
* PULL-UP RESISTOR AND
ZENER ARE OPTIONAL
80
COMP1
TRACK2
SGND
470µF
6.3V
VFB1
LTM4620
TRACK1
0.1µF
6.3V
SW1
RUN1
RUN2
5.1V*
90
+
100µF
EFFICIENCY (%)
VIN 4.5V TO 16V
100µF
6.3V
+
VOUT
1.2V AT 26A
470µF
6.3V
40
5VIN /500kHz
12VIN /500kHz
0 2 4 6 8 10 12 14 16 18 20 22 24 26
OUTPUT CURRENT (A)
4620 TA01b
PGOOD
4620 TA01a
4620fc
For more information www.linear.com/LTM4620
1
LTM4620
ABSOLUTE MAXIMUM RATINGS
(Note 1)
VIN (Note 8)..................................................–0.3V to 18V
VSW1, VSW2.....................................................–1V to 18V
PGOOD1, PGOOD2, RUN1, RUN2,
INTVCC , EXTVCC........................................... –0.3V to 6V
MODE_PLLIN, fSET, TRACK1, TRACK2,
DIFFOUT, PHASMD................................ –0.3V to INTVCC
VOUT1, VOUT2, VOUTS1, VOUTS2...................... –0.3V to 6V
DIFFP, DIFFN.......................................... –0.3V to INTVCC
COMP1, COMP2, VFB1, VFB2 (Note 6)......... –0.3V to 2.7V
INTVCC Peak Output Current.................................100mA
Internal Operating Temperature Range (Note 2)
E- and I-Grade.................................... –40°C to 125°C
MP-Grade........................................... –55°C to 125°C
Storage Temperature Range................... –55°C to 125°C
Peak Package Body Temperature........................... 245°C
PIN CONFIGURATION
TOP VIEW
TOP VIEW
TEMP
TEMP
EXTVCC
L
L
VIN
J
J
PHASMD
MODE_PLLIN
TRACK1
VFB1
VOUTS1
VIN
K
K
CLKOUT
SW1
EXTVCC
M
M
INTVCC
SW2
PGOOD1
PGOOD2
RUN2
DIFFOUT
DIFFP
DIFFN
H
G
RUN1
SGND
F
GND
COMP1 COMP2
E
SGND VFB2 TRACK2
D
GND
CLKOUT
SW1
PHASMD
MODE_PLLIN
TRACK1
VFB1
fSET SGND VOUTS2
C
VOUTS1
B
VOUT1
G
RUN1
SGND
F
GND
COMP1 COMP2
E
SGND VFB2 TRACK2
D
GND
fSET SGND VOUTS2
C
B
VOUT2
GND
INTVCC
SW2
PGOOD1
PGOOD2
RUN2
DIFFOUT
DIFFP
DIFFN
H
VOUT1
VOUT2
GND
A
A
1
2
3
4
5
6
7
8
9
10
11
1
12
2
TJMAX = 125°C, θJA = 7°C/W, θJCbottom = 1.5°C/W,
θJCtop = 3.7°C/W, θJB + θBA ≅ 7°C/W
θ VALUES DEFINED PER JESD 51-12
WEIGHT = 3.037g
ORDER INFORMATION
PAD OR BALL FINISH
Au (RoHS)
4
5
6
7
8
9
10
11
12
TJMAX = 125°C, θJA = 7°C/W, θJCbottom = 1.5°C/W,
θJCtop = 3.7°C/W, θJB + θBA ≅ 7°C/W
θ VALUES DEFINED PER JESD 51-12
WEIGHT = 3.232g
http://www.linear.com/product/LTM4620#orderinfo
PART MARKING*
PART NUMBER
LTM4620EV#PBF
3
BGA PACKAGE
144-LEAD (15mm × 15mm × 5.01mm)
LGA PACKAGE
144-LEAD (15mm × 15mm × 4.41mm)
DEVICE
LTM4620V
FINISH CODE
e4
PACKAGE
TYPE
LGA
MSL
RATING
3
TEMPERATURE RANGE
(Note 2)
–40°C to 125°C
LTM4620IV#PBF
Au (RoHS)
LTM4620V
e4
LGA
3
–40°C to 125°C
LTM4620EY#PBF
SAC305 (RoHS)
LTM4620Y
e1
BGA
3
–40°C to 125°C
LTM4620IY#PBF
SAC305 (RoHS)
LTM4620Y
e1
BGA
3
–40°C to 125°C
LTM4620IY
SnPb (63/37)
LTM4620Y
e0
BGA
3
–40°C to 125°C
LTM4620MPY#PBF
SAC305 (RoHS)
LTM4620Y
e1
BGA
3
–55°C to 125°C
LTM4620MPY
SnPb (63/37)
LTM4620Y
e0
BGA
3
–55°C to 125°C
Consult Marketing for parts specified with wider operating temperature
ranges. *Device temperature grade is indicated by a label on the shipping
container. Pad or ball finish code is per IPC/JEDEC J-STD-609.
• Recommended LGA and BGA PCB Assembly and Manufacturing
Procedures:
www.linear.com/umodule/pcbassembly
• Terminal Finish Part Marking:
www.linear.com/leadfree
• LGA and BGA Package and Tray Drawings:
www.linear.com/packaging
2
4620fc
For more information www.linear.com/LTM4620
LTM4620
ELECTRICAL
CHARACTERISTICS
The
l denotes the specifications which apply over the specified internal
operating temperature range (Note 2). Specified as each individual output channel. TA = 25°C, VIN = 12V and VRUN1, VRUN2 at 5V
unless otherwise noted. Per the typical application in Figure 23.
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
VIN
Input DC Voltage
l
4.5
16
V
VOUT
Output Voltage
(Note 8)
l
0.6
2.5
V
VOUT1(DC),
VOUT2(DC)
Output Voltage, Total Variation with
Line and Load
CIN = 22µF × 3, COUT = 100µF × 1 Ceramic,
470µF POSCAP, VOUT = 1.5V
l
1.477
1.5
1.523
V
RUN Pin On/Off Threshold
RUN Rising
1.1
1.25
1.40
V
Input Specifications
VRUN1, VRUN2
VRUN1HYS , VRUN2HYS RUN Pin On Hysteresis
150
mV
IINRUSH(VIN)
Input Inrush Current at Start-Up
IOUT = 0A, CIN = 22µF ×3, CSS = 0.01µF,
COUT = 100µF ×3, VOUT1 = 1.5V, VOUT2 = 1.5V,
VIN = 12V
1
A
IQ(VIN)
Input Supply Bias Current
VIN = 12V, VOUT = 1.5V, Burst Mode Operation
VIN = 12V, VOUT = 1.5V, Pulse-Skipping Mode
VIN = 12V, VOUT= 1.5V, Switching Continuous
Shutdown, RUN = 0, VIN = 12V
5
15
65
50
mA
mA
mA
µA
IS(VIN)
Input Supply Current
VIN = 5V, VOUT = 1.5V, IOUT = 13A
VIN = 12V, VOUT = 1.5V, IOUT = 13A
IOUT1(DC), IOUT2(DC)
Output Continuous Current Range
VIN = 12V, VOUT = 1.5V (Notes 7, 8)
ΔVOUT1(LINE) /VOUT1
ΔVOUT2(LINE) /VOUT2
Line Regulation Accuracy
VOUT = 1.5V, VIN from 4.5V to 16V
IOUT = 0A for Each Output,
l
0.01
0.025
%/V
ΔVOUT1/VOUT1
ΔVOUT2 /VOUT2
Load Regulation Accuracy
For Each Output, VOUT = 1.5V, 0A to 13A
VIN = 12V (Note 7)
l
0.5
0.75
%
4.6
1.853
A
A
Output Specifications
0
13
A
VOUT1(AC), VOUT2(AC) Output Ripple Voltage
For Each Output, IOUT = 0A, COUT = 100µF ×3/
X7R/Ceramic, 470µF POSCAP, VIN = 12V,
VOUT = 1.5V, Frequency = 400kHz
fS (Each Channel)
Output Ripple Voltage Frequency
VIN = 12V, VOUT = 1.5V, fSET = 1.25V (Note 4)
fSYNC
(Each Channel)
SYNC Capture Range
∆VOUTSTART
(Each Channel)
Turn-On Overshoot
COUT = 100µF/X5R/Ceramic, 470µF POSCAP,
VOUT = 1.5V, IOUT = 0A VIN = 12V
10
mV
tSTART
(Each Channel)
Turn-On Time
COUT = 100µF/X5R/Ceramic, 470µF POSCAP,
No Load, TRACK/SS with 0.01µF to GND,
VIN = 12V
5
ms
∆VOUT(LS)
(Each Channel)
Peak Deviation for Dynamic Load
Load: 0% to 50% to 0% of Full Load
COUT = 22µF ×3/X5R/Ceramic, 470µF POSCAP
VIN = 12V, VOUT = 1.5V
30
mV
tSETTLE
(Each Channel)
Settling Time for Dynamic Load
Step
Load: 0% to 50% to 0% of Full Load,
VIN = 12V, COUT = 100µF, 470µF POSCAP
20
µs
IOUT(PK)
(Each Channel)
Output Current Limit
VIN = 12V, VOUT = 1.5V
20
A
15
mVP-P
500
400
kHz
780
kHz
Control Section
VFB1, VFB2
Voltage at VFB Pins
IFB1, IFB2
VOVL
IOUT = 0A, VOUT = 1.5V
l
0.592
(Note 6)
Feedback Overvoltage Lockout
l
0.64
0.600
0.606
V
–5
–20
nA
0.66
0.68
V
4620fc
For more information www.linear.com/LTM4620
3
LTM4620
ELECTRICAL CHARACTERISTICS
The l denotes the specifications which apply over the specified internal
operating temperature range (Note 2). Specified as each individual output channel. TA = 25°C, VIN = 12V and VRUN1, VRUN2 at 5V
unless otherwise noted. Per the typical application in Figure 23.
SYMBOL
PARAMETER
CONDITIONS
TRACK1 (I),
TRACK2 (I)
Track Pin Soft-Start Pull-Up Current
TRACK1 (I),TRACK2 (I) Start at 0V
UVLO
Undervoltage Lockout
VIN Falling
VIN Rising
MIN
TYP
MAX
1
1.25
1.5
UVLO Hysteresis
tON(MIN)
Minimum On-Time
RFBHI1, RFBHI2
Resistor Between VOUTS1, VOUTS2
and VFB1, VFB2 Pins for Each Output
VPGOOD1, VPGOOD2
Low
PGOOD Voltage Low
IPGOOD = 2mA
IPGOOD
PGOOD Leakage Current
VPGOOD = 5V
VPGOOD
PGOOD Trip Level
VFB with Respect to Set Output Voltage
VFB Ramping Negative
VFB Ramping Positive
(Note 6)
60.05
UNITS
µA
3.3
3.9
V
V
0.6
V
90
ns
60.4
60.75
0.1
0.3
V
±5
µA
–10
10
kΩ
%
%
INTVCC Linear Regulator
VINTVCC
Internal VCC Voltage
6V < VIN < 16V
VINTVCC
Load Regulation
INTVCC Load Regulation
ICC = 0mA to 50mA
VEXTVCC
EXTVCC Switchover Voltage
EXTVCC Ramping Positive
VEXTVCC(DROP)
EXTVCC Dropout
ICC = 20mA, VEXTVCC = 5V
VEXTVCC(HYST)
EXTVCC Hysteresis
4.8
4.5
5
5.2
V
0.5
2
%
100
mV
4.7
50
V
200
mV
Oscillator and Phase-Locked Loop
Frequency Nominal
Nominal Frequency
fSET = 1.2V
450
500
550
kHz
Frequency Low
Lowest Frequency
fSET = 0V (Note 5)
210
250
290
kHz
fSET > 2.4V, Up to INTVCC
700
780
860
kHz
9
10
11
µA
Frequency High
Highest Frequency
fSET
Frequency Set Current
RMODE_PLLIN
MODE_PLLIN Input Resistance
CLKOUT
Phase (Relative to VOUT1)
CLK High
CLK Low
Clock High Output Voltage
Clock Low Output Voltage
PHASMD = GND
PHASMD = Float
PHASMD = INTVCC
250
kΩ
60
90
120
Deg
Deg
Deg
2
0.2
V
V
Differential Amplifier
AV Differential
Amplifier
Gain
RIN
Input Resistance
Measured at DIFFP Input
VOS
Input Offset Voltage
VDIFFP = VDIFFOUT = 1.5V, IDIFFOUT = 100µA
PSRR Differential
Amplifier
Power Supply Rejection Ratio
5V < VIN < 16V
ICL
Maximum Output Current
VOUT(MAX)
Maximum Output Voltage
4
IDIFFOUT = 300µA
1
V/V
80
kΩ
3
INTVCC – 1.4
mV
90
dB
2
mA
V
4620fc
For more information www.linear.com/LTM4620
LTM4620
ELECTRICAL CHARACTERISTICS
The l denotes the specifications which apply over the specified internal
operating temperature range (Note 2). Specified as each individual output channel. TA = 25°C, VIN = 12V and VRUN1, VRUN2 at 5V
unless otherwise noted. Per the typical application in Figure 23.
SYMBOL
PARAMETER
GBW
Gain Bandwidth Product
VTEMP Temp Diode
Diode Connected PNP
TC
Temperature Coefficient
CONDITIONS
MIN
TYP
3
I = 100µA
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2: The LTM4620 is tested under pulsed load conditions such that
TJ ≈ TA. The LTM4620E is guaranteed to meet specifications from
0°C to 125°C internal temperature. Specifications over the –40°C to
125°C internal operating temperature range are assured by design,
characterization and correlation with statistical process controls. The
LTM4620I is guaranteed over the full –40°C to 125°C internal operating
temperature range. The LTM4620MP is tested and guaranteed over the
–55°C to 125°C operating temperature range. For output current derating
at high temperature, please refer to thermal conditions and output
current derating discussion. Note that the maximum ambient temperature
consistent with these specifications is determined by specific operating
conditions in conjunction with board layout, the rated package thermal
impedance and other environmental factors.
MAX
UNITS
MHz
0.598
V
–2.0
mV/°C
Note 3: Two outputs are tested separately and the same testing condition
is applied to each output.
Note 4: The switching frequency is programmable from 400kHz to 750kHz.
Note 5: LTM4620 device is designed to operate from 400kHz to 750kHz
Note 6: These parameters are tested at wafer sort.
Note 7: See output current derating curves for different VIN, VOUT and TA.
Note 8: Output current limitations. For 10V ≤ VIN ≤ 16V, the 2.5V output
current needs to be limited to 10A/channel, switching frequency = 750kHz.
Derating curves apply. For 5V ≤ VIN ≤ 9V, the 2.5V output current needs
to be limited to 12A/channel, switching frequency = 750kHz. Derating
curves apply. All other input and output combinations are 13A/channel
with recommended switching frequency included in the efficiency graphs.
Derating curves apply.
4620fc
For more information www.linear.com/LTM4620
5
LTM4620
TYPICAL PERFORMANCE CHARACTERISTICS
95
95
EFFICIENCY (%)
EFFICIENCY (%)
90
85
80
75
70
65
60
1VOUT, f = 400kHz
1.2VOUT, f = 500kHz
1.5VOUT, f = 550kHz
1.8VOUT, f = 600kHz
2.5VOUT, f = 750kHz
0 1 2 3 4 5 6 7 8 9 10 11 12 13
OUTPUT CURRENT (A)
Efficiency vs Output Current,
VIN = 12V
95
90
90
85
85
EFFICIENCY (%)
100
Efficiency vs Output Current,
VIN = 5V
80
75
70
65
60
1VOUT, f = 400kHz
1.2VOUT, f = 500kHz
1.5VOUT, f = 550kHz
1.8VOUT, f = 600kHz
2.5VOUT, f = 750kHz
0 1 2 3 4 5 6 7 8 9 10 11 12 13
OUTPUT CURRENT (A)
4620 G01
80
75
70
65
60
0 2 4 6 8 10 12 14 16 18 20 22 24 26
OUTPUT CURRENT (A)
4620 G03
Single Phase Single Output
Load Transient Response
Single Phase Single Output
Load Transient Response
VOUT
100mV/DIV
VOUT
100mV/DIV
VOUT
100mV/DIV
ILOAD
10A/DIV
ILOAD
5A/DIV
ILOAD
5A/DIV
50µs/DIV
4620 G04
50µs/DIV
4620 G05
12VIN, 1.5VOUT AT 26A/µs LOAD STEP
COUT = 4× 470µF, 4V POSCAP AND
2× 100µF, 6.3V CERAMIC
12VIN, 1VOUT AT 13A/µs LOAD STEP
COUT = 2× 470µF, 4V POSCAP AND
1× 100µF, 6.3V CERAMIC
12VIN, 1.2VOUT AT 13A/µs LOAD STEP
COUT = 2× 470µF, 4V POSCAP AND
1× 100µF, 6.3V CERAMIC
Single Phase Single Output
Load Transient Response
Single Phase Single Output
Load Transient Response
Single Phase Single Output
Load Transient Response
VOUT
100mV/DIV
VOUT
100mV/DIV
VOUT
100mV/DIV
ILOAD
5A/DIV
ILOAD
5A/DIV
ILOAD
5A/DIV
50µs/DIV
12VIN, 1.5VOUT AT 13A/µs LOAD STEP
COUT = 2× 470µF, 4V POSCAP AND
1× 100µF, 6.3V CERAMIC
6
1VOUT, f = 400kHz
1.2VOUT, f = 500kHz
1.5VOUT, f = 550kHz
1.8VOUT, f = 600kHz
2.5VOUT, f = 750kHz
4620 G02
Dual Phase Single Output
Load Transient Response
50µs/DIV
Dual Phase Single Output Efficiency
vs Output Current, VIN = 12V
4620 G07
50µs/DIV
4620 G08
12VIN, 1.8VOUT AT 13A/µs LOAD STEP
COUT = 2× 470µF, 4V POSCAP AND
1× 100µF, 6.3V CERAMIC
50µs/DIV
4620 G06
4620 G09
12VIN, 2.5VOUT AT 13A/µs LOAD STEP
COUT = 2× 470µF, 4V POSCAP AND
1× 100µF, 6.3V CERAMIC
4620fc
For more information www.linear.com/LTM4620
LTM4620
TYPICAL PERFORMANCE CHARACTERISTICS
Single Phase Single Output
Start-Up
Single Phase Single Output
Start-Up
VOUT
0.5V/DIV
VOUT
0.5V/DIV
IOUT
1A/DIV
IOUT
5A/DIV
2ms/DIV
12VIN, 1.5VOUT AT NO LOAD
COUT = 2× 470µF, 4V SANYO POSCAP,
1× 100µF, 6.3V CERAMIC
SOFT-START CAPACITOR = 0.01µF
USE RUN PIN TO CONTROL START-UP
12VIN, 1.5VOUT AT 10A LOAD
COUT = 2× 470µF, 4V SANYO POSCAP,
1× 100µF, 6.3V X5R CERAMIC
SOFT-START CAPACITOR = 0.01µF
USE RUN PIN TO CONTROL START-UP
Current Limit and Current
Foldback
Load Regulation vs Current
1.8
VIN = 12V
VOUT = 1.5V
1.6
LOAD REGULATION (mV)
1.2
1.0
0.8
0.6
0.4
4620 G11
VIN = 12V
VOUT = 1.5V
1.0
1.4
OUTPUT VOLTAGE (V)
2ms/DIV
4620 G10
0.8
0.6
0.4
0.2
0.2
0
0
5
10
15
20
OUTPUT CURRENT (A)
25
0
0
4620 G12
5
10
OUTPUT CURRENT (A)
15
4620 G13
Short-Circuit Protection
Short-Circuit Protection
VOUT
500mV/DIV
VOUT
500mV/DIV
IIN
2A/DIV
IIN
2A/DIV
VIN = 12V
VOUT = 1.5V
IOUT = NO LOAD
50µs/DIV
4620 G14
VIN = 12V
VOUT = 1.5V
IOUT = 13A
50µs/DIV
4620 G15
4620fc
For more information www.linear.com/LTM4620
7
LTM4620
PIN FUNCTIONS
(Recommended to Use Test Points to Monitor Signal Pin Connections.)
PACKAGE ROW AND COLUMN LABELING MAY VARY
AMONG µModule PRODUCTS. REVIEW EACH PACKAGE
LAYOUT CAREFULLY.
VOUT1 (A1-A5, B1-B5, C1-C4): Power Output Pins.
Apply output load between these pins and GND pins.
Recommend placing output decoupling capacitance
directly between these pins and GND pins. Review Table
4. See Note 8 in the Electrical Characteristics section for
output current guideline.
GND (A6-A7, B6-B7, D1-D4, D9-D12, E1-E4, E10-E12,
F1-F3, F10-F12, G1, G3, G10, G12, H1-H7, H9-H12, J1,
J5, J8, J12, K1, K5-K8, K12, L1, L12, M1 , M12): Power
Ground Pins for Both Input and Output Returns.
VOUT2 (A8-A12, B8-B12, C9-C12): Power Output Pins.
Apply output load between these pins and GND pins.
Recommend placing output decoupling capacitance
directly between these pins and GND pins. Review Table 4.
See Note 8 in the Electrical Characteristics section for
output current guideline.
VOUTS1, VOUTS2 (C5, C8): This pin is connected to the top
of the internal top feedback resistor for each output. The
pin can be directly connected to its specific output, or
connected to DIFFOUT when the remote sense amplifier is
used. In paralleling modules, one of the VOUTS pins is connected to the DIFFOUT pin in remote sensing or directly
to VOUT with no remote sensing. It is very important to
connect these pins to either the DIFFOUT or VOUT since
this is the feedback path, and cannot be left open. See the
Applications Information section.
fSET (C6): Frequency Set Pin. A 10µA current is sourced
from this pin. A resistor from this pin to ground sets a
voltage that in turn programs the operating frequency.
Alternatively, this pin can be driven with a DC voltage
that can set the operating frequency. See the Applications
Information section.
SGND (C7, D6, G6-G7, F6-F7): Signal Ground Pin. Return
ground path for all analog and low power circuitry. Tie
a single connection to the output capacitor GND in the
application. See layout guidelines in Figure 22.
VFB1, VFB2 (D5, D7): The Negative Input of the Error
Amplifier for Each Channel. Internally, this pin is connected to VOUTS1 or VOUTS2 with a 60.4kΩ precision
resistor. Different output voltages can be programmed
with an additional resistor between VFB and GND pins. In
PolyPhase® operation, tying the VFB pins together allows
for parallel operation. See the Applications Information
section for details.
TRACK1, TRACK2 (E5, D8): Output Voltage Tracking Pin
and Soft-Start Inputs. Each channel has a 1.3µA pull-up
current source. When one channel is configured to be
master of the two channels, then a capacitor from this pin
to ground will set a soft-start ramp rate. The remaining
channel can be set up as the slave, and have the master’s
output applied through a voltage divider to the slave output’s track pin. This voltage divider is equal to the slave
output’s feedback divider for coincidental tracking. See
the Applications Information section.
COMP1, COMP2 (E6, E7): Current control threshold and
error amplifier compensation point for each channel. The
current comparator threshold increases with this control
voltage. Tie the COMP pins together for parallel operation.
The device is internal compensated.
DIFFP (E8): Positive input of the remote sense amplifier.
This pin is connected to the remote sense point of the
output voltage. See the Applications Information section.
DIFFN (E9): Negative input of the remote sense amplifier.
This pin is connected to the remote sense point of the
output GND. See the Applications Information section.
MODE_PLLIN (F4): Force Continuous Mode, Burst Mode
Operation, or Pulse-Skipping Mode Selection Pin and
External Synchronization Input to Phase Detector Pin.
Connect this pin to SGND to force both channels into
force continuous mode of operation. Connect to INTVCC
to enable pulse-skipping mode of operation. Leaving the
pin floating will enable Burst Mode operation. A clock on
the pin will force both channels into continuous mode of
operation and synchronized to the external clock applied
to this pin.
Heat Sink (Top Exposed Metal): The top exposed metal
is at ground potential.
8
4620fc
For more information www.linear.com/LTM4620
LTM4620
PIN FUNCTIONS
(Recommended to Use Test Points to Monitor Signal Pin Connections.)
RUN1, RUN2 (F5, F9): Run Control Pin. A voltage above
1.25V will turn on each channel in the module. A voltage
below 1.25V on the RUN pin will turn off the related channel. Each RUN pin has a 1µA pull-up current, once the
RUN pin reaches 1.2V an additional 4.5µA pull-up current
is added to this pin.
DIFFOUT (F8): Internal Remote Sense Amplifier Output.
Connect this pin to VOUTS1 or VOUTS2 depending on which
output is using remote sense. In parallel operation connect one of the VOUTS pin to DIFFOUT for remote sensing.
SW1, SW2 (G2, G11): Switching node of each channel
that is used for testing purposes. Also an R-C snubber
network can be applied to reduce or eliminate switch node
ringing, or otherwise leave floating. See the Applications
Information section.
PHASMD (G4): Connect this pin to SGND, INTVCC, or
floating this pin to select the phase of CLKOUT to 60
degrees, 120 degrees, and 90 degrees respectively.
CLKOUT (G5): Clock output with phase control using the
PHASMD pin to enable multiphase operation between
devices. See the Applications Information section.
PGOOD1, PGOOD2 (G9, G8): Output Voltage Power Good
Indicator. Open drain logic output that is pulled to ground
when the output voltage is not within ±10% of the regulation point.
INTVCC (H8): Internal 5V Regulator Output. The control
circuits and internal gate drivers are powered from this
voltage. Decouple this pin to PGND with a 4.7µF low ESR
tantalum or ceramic. INTVCC is activated when either
RUN1 or RUN2 is activated.
TEMP (J6): Onboard Temperature Diode for Monitoring
the VBE Junction Voltage Change with Temperature. See
the Applications Information section.
EXTVCC (J7): External power input that is enabled through
a switch to INTVCC whenever EXTVCC is greater than 4.7V.
Do not exceed 6V on this input, and connect this pin to
VIN when operating VIN on 5V. An efficiency increase will
occur that is a function of the (VIN – INTVCC) multiplied
by power MOSFET driver current. Typical current requirement is 30mA. VIN must be applied before EXTVCC , and
EXTVCC must be removed before VIN.
VIN (M2-M11, L2-L11, J2-J4, J9-J11, K2-K4, K9-K11):
Power Input Pins. Apply input voltage between these pins
and GND pins. Recommend placing input decoupling
capacitance directly between VIN pins and GND pins.
Top Heat Sink: Top heat sink is at ground potential.
4620fc
For more information www.linear.com/LTM4620
9
LTM4620
SIMPLIFIED BLOCK DIAGRAM
PGOOD1
TRACK1
VIN
SS CAP
VIN
= 100µA VIN
RT
CIN1
22µF
25V
1µF
GND
RT
TEMP
MTOP1
SW1
CLKOUT
0.33µH
RUN1
MODE_PLLIN
VOUT1
2.2µF
MBOT1
PHASMD
CIN2
22µF
25V
+
GND
VOUT1
1.5V/13A
COUT1
VOUTS1
COMP1
60.4k
VFB1
INTERNAL
COMP
SGND
RFB1
40.2k
POWER
CONTROL
PGOOD2
TRACK2
VIN
INTVCC
SS CAP
CIN3
22µF
25V
1µF
4.7µF
GND
EXTVCC
MTOP2
SW2
0.33µH
RUN2
CIN4
22µF
25V
VOUT2
2.2µF
MBOT2
GND
+
VOUT2
1.2V/13A
COUT2
VOUTS2
60.4k
COMP2
fSET
RfSET
121k
SGND
+ –
VFB2
RFB2
60.4k
INTERNAL
COMP
INTERNAL
FILTER
DIFFOUT
DIFFN
DIFFP
4620 BD
Figure 1. Simplified LTM4620 Block Diagram
DECOUPLING REQUIREMENTS
TA = 25°C. Use Figure 1 configuration.
SYMBOL
PARAMETER
CONDITIONS
CIN1, CIN2
CIN3, CIN4
External Input Capacitor Requirement
(VIN = 4.5V to 16V, VOUT1 = 1.5V)
(VIN = 4.5V to 16V, VOUT2 = 1.2V)
IOUT1 = 13A
IOUT2 = 13A (Note 8)
22
22
µF
µF
COUT1
COUT2
External Output Capacitor Requirement
(VIN = 4.5V to 16V, VOUT1 = 1.5V)
(VIN = 4.5V to 16V, VOUT2 = 1.2V)
IOUT1 = 13A
IOUT2 = 13A (Note 8)
300
300
µF
µF
10
MIN
TYP
MAX
UNITS
4620fc
For more information www.linear.com/LTM4620
LTM4620
OPERATION
Power Module Description
The LTM4620 is a dual-output standalone nonisolated
switching mode DC/DC power supply. It can provide two
13A outputs with few external input and output capacitors
and setup components. This module provides precisely
regulated output voltages programmable via external
resistors from 0.6VDC to 2.5VDC over 4.5V to 16V input
voltages. The typical application schematic is shown in
Figure 23. See Note 8 in the Electrical Characteristics section for output current guideline.
The LTM4620 has dual integrated constant-frequency current mode regulators and built-in power MOSFET devices
with fast switching speed. The typical switching frequency
is 500kHz. For switching-noise sensitive applications, it
can be externally synchronized from 400kHz to 780kHz.
A resistor can be used to program a free run frequency
on the fSET pin. See the Applications Information section.
With current mode control and internal feedback loop
compensation, the LTM4620 module has sufficient stability margins and good transient performance with a wide
range of output capacitors, even with all ceramic output
capacitors.
Current mode control provides cycle-by-cycle fast current
limit and foldback current limit in an overcurrent condition. Internal overvoltage and undervoltage comparators
pull the open-drain PGOOD outputs low if the output
feedback voltage exits a ±10% window around the regulation point. As the output voltage exceeds 10% above
regulation, the bottom MOSFET will turn on to clamp the
output voltage. The top MOSFET will be turned off. This
overvoltage protect is feedback voltage referred.
Pulling the RUN pins below 1.1V forces the regulators
into a shutdown state, by turning off both MOSFETs.
The TRACK pins are used for programming the output
voltage ramp and voltage tracking during start-up or
used for soft-starting the regulator. See the Applications
Information section.
The LTM4620 is internally compensated to be stable over
all operating conditions. Table 4 provides a guide line for
input and output capacitances for several operating conditions. The LTpowerCAD® will be provided for transient
and stability analysis. The VFB pin is used to program the
output voltage with a single external resistor to ground.
A differential remote sense amplifier is available for sensing the output voltage accurately on one of the outputs at
the load point, or in parallel operation sensing the output
voltage at the load point.
Multiphase operation can be easily employed with the
MODE_PLLIN, PHASMD, and CLKOUT pins. Up to 12
phases can be cascaded to run simultaneously with
respect to each other by programming the PHASMD pin to
different levels. See the Applications Information section.
High efficiency at light loads can be accomplished with
selectable Burst Mode operation or pulse-skipping operation using the MODE_PLLIN pin. These light load features will accommodate battery operation. Efficiency
graphs are provided for light load operation in the Typical
Performance Characteristics section. See the Applications
Information section for details.
A temperature diode is included inside the module to monitor the temperature of the module. See the Applications
Information section for details.
A TEMP pin is provided to allow the internal device temperature to be monitored using an onboard diode connected PNP transistor. This diode connected PNP transistor is grounded in the module and can be used as a general temperature monitor using a device that is designed
to monitor the single-ended connection.
4620fc
For more information www.linear.com/LTM4620
11
LTM4620
APPLICATIONS INFORMATION
The typical LTM4620 application circuit is shown in
Figure 23. External component selection is primarily
determined by the maximum load current and output
voltage. Refer to Table 4 for specific external capacitor
requirements for particular applications.
VIN to VOUT Step-Down Ratios
There are restrictions in the maximum VIN and VOUT stepdown ratio that can be achieved for a given input voltage.
Each output of the LTM4620 is capable of 98% duty cycle,
but the VIN to VOUT minimum dropout is still shown as a
function of its load current and will limit output current
capability related to high duty cycle on the top side switch.
Minimum on-time tON(MIN) is another consideration in
operating at a specified duty cycle while operating at a
certain frequency due to the fact that tON(MIN) < D/fSW,
where D is duty cycle and fSW is the switching frequency.
tON(MIN) is specified in the electrical parameters as 90ns.
See Note 8 in the Electrical Characteristics section for
output current guideline.
Output Voltage Programming
The PWM controller has an internal 0.6V reference voltage. As shown in the Block Diagram, a 60.4kΩ internal
feedback resistor connects between the VOUTS1 to VFB1
and VOUTS2 to VFB2. It is very important that these pins
be connected to their respective outputs for proper feedback regulation. Overvoltage can occur if these VOUTS1
and VOUTS2 pins are left floating when used as individual
regulators, or at least one of them is used in paralleled
regulators. The output voltage will default to 0.6V with no
feedback resistor on either VFB1 or VFB2. Adding a resistor
RFB from VFB pin to GND programs the output voltage:
60.4k + RFB
VOUT = 0.6V •
RFB
resistors to the output. All of the VFB pins tie together with
one programming resistor as shown in Figure 2.
In parallel operation, the VFB pins have an IFB current of 20nA
maximum each channel. To reduce output voltage error due
to this current, an additional VOUTS pin can be tied to VOUT,
and an additional RFB resistor can be used to lower the total
Thevenin equivalent resistance seen by this current. For
example in Figure 2, the total Thevenin equivalent resistance
of the VFB pin is (60.4k//RFB), which is 30.2k where RFB is
equal to 60.4k for a 1.2V output. Four phases connected
in parallel equates to a worse case feedback current of
4 • IFB = 80nA maximum. The voltage error is 80nA • 30.2k
= 2.4mV. If VOUTS2 is connected, as shown in Figure 2, to
VOUT, and another 60.4k resistor is connected from VFB2
to ground, then the voltage error is reduced to 1.2mV. If
the voltage error is acceptable then no additional connections are necessary. The onboard 60.4k resistor is 0.5%
accurate and the VFB resistor can be chosen by the user to
be as accurate as needed. All COMP pins are tied together
for current sharing between the phases. The TRACK pins
can be tied together and a single soft-start capacitor can be
used to soft-start the regulator. The soft-start equation will
need to have the soft-start current parameter increased by
the number of paralleled channels. See the Output Voltage
Tracking section.
COMP1
LTM4620
VOUT2
COMP2
60.4k
VOUTS1
VOUTS2
TRACK1
60.4k
VFB2
TRACK2
COMP1
LTM4620
60.4k
VOUT1
1.0V
1.2V
1.5V
1.8V
2.5V
VOUTS2
RFB
Open
90.9k
60.4k
40.2k
30.2k
19.1k
VFB1
0.1µF
TRACK2
USE TO LOWER
TOTAL EQUIVALENT
RESISTANCE TO LOWER
IFB VOLTAGE ERROR
VOUTS1
0.6V
TRACK1
OPTIONAL
RFB
60.4k
VOUT2
COMP2
VOUT
12
OPTIONAL CONNECTION
VFB1
Table 1. VFB Resistor Table vs Various Output Voltages
For parallel operation of multiple channels the same feedback setting resistor can be used for the parallel design.
This is done by connecting the VOUTS1 to the output as
shown in Figure 2, thus tying one of the internal 60.4k
4 PARALLELED OUTPUTS
FOR 1.2V AT 50A
VOUT1
60.4k
VFB2
4620 F02
RFB
60.4k
Figure 2. 4-Phase Parallel Configurations
4620fc
For more information www.linear.com/LTM4620
LTM4620
APPLICATIONS INFORMATION
Input Capacitors
Output Capacitors
The LTM4620 module should be connected to a low
AC-impedance DC source. For the regulator input four
22µF input ceramic capacitors are used for RMS ripple
current. A 47µF to 100µF surface mount aluminum electrolytic bulk capacitor can be used for more input bulk
capacitance. This bulk input capacitor is only needed
if the input source impedance is compromised by long
inductive leads, traces or not enough source capacitance.
If low impedance power planes are used, then this bulk
capacitor is not needed.
The LTM4620 is designed for low output voltage ripple
noise and good transient response. The bulk output
capacitors defined as COUT are chosen with low enough
effective series resistance (ESR) to meet the output voltage ripple and transient requirements. COUT can be a low
ESR tantalum capacitor, the low ESR polymer capacitor
or ceramic capacitor. The typical output capacitance range
for each output is from 200µF to 470µF. Additional output
filtering may be required by the system designer, if further
reduction of output ripples or dynamic transient spikes
is required. Table 4 shows a matrix of different output
voltages and output capacitors to minimize the voltage
droop and overshoot during a 7A/µs transient. The table
optimizes total equivalent ESR and total bulk capacitance
to optimize the transient performance. Stability criteria are
considered in the Table 4 matrix, and LTpowerCAD will be
provided for stability analysis. Multiphase operation will
reduce effective output ripple as a function of the number of phases. Application Note 77 discusses this noise
reduction versus output ripple current cancellation, but
the output capacitance should be considered carefully as a
function of stability and transient response. LTpowerCAD
can calculate the output ripple reduction as the number
of implemented phases increases by N times. A small
value 10Ω to 50Ω resistor can be placed in series from
VOUT to the VOUTS pin to allow for a bode plot analyzer to
inject a signal into the control loop and validate the regulator stability. The same resistor could be placed in series
from VOUT to DIFFP and a bode plot analyzer could inject
a signal into the control loop and validate the regulator
stability.
For a buck converter, the switching duty-cycle can be
estimated as:
D=
VOUT
VIN
Without considering the inductor current ripple, for each
output, the RMS current of the input capacitor can be
estimated as:
IOUT(MAX)
ICIN(RMS) =
• D • (1− D)
η%
In the above equation, η% is the estimated efficiency of
the power module. The bulk capacitor can be a switcherrated electrolytic aluminum capacitor, Polymer capacitor.
4620fc
For more information www.linear.com/LTM4620
13
LTM4620
APPLICATIONS INFORMATION
Burst Mode Operation
The LTM4620 is capable of Burst Mode operation on each
regulator in which the power MOSFETs operate intermittently based on load demand, thus saving quiescent current. For applications where maximizing the efficiency at
very light loads is a high priority, Burst Mode operation
should be applied. Burst Mode operation is enabled with
the MODE_PLLIN pin floating. During this operation, the
peak current of the inductor is set to approximately one
third of the maximum peak current value in normal operation even though the voltage at the COMP pin indicates
a lower value. The voltage at the COMP pin drops when
the inductor’s average current is greater than the load
requirement. As the COMP voltage drops below 0.5V, the
burst comparator trips, causing the internal sleep line to
go high and turn off both power MOSFETs.
In sleep mode, the internal circuitry is partially turned off,
reducing the quiescent current to about 450µA for each
output. The load current is now being supplied from the
output capacitors. When the output voltage drops, causing COMP to rise above 0.5V, the internal sleep line goes
low, and the LTM4620 resumes normal operation. The
next oscillator cycle will turn on the top power MOSFET
and the switching cycle repeats. Either regulator can be
configured for Burst Mode operation.
Pulse-Skipping Mode Operation
In applications where low output ripple and high efficiency at intermediate currents are desired, pulse-skipping mode should be used. Pulse-skipping operation
allows the LTM4620 to skip cycles at low output loads,
thus increasing efficiency by reducing switching loss.
Tying the MODE_PLLIN pin to INTVCC enables pulseskipping operation. At light loads the internal current
comparator may remain tripped for several cycles and
force the top MOSFET to stay off for several cycles, thus
skipping cycles. The inductor current does not reverse
in this mode. This mode will maintain higher effective
14
frequencies thus lower output ripple and lower noise than
Burst Mode operation. Either regulator can be configured
for pulse-skipping mode.
Forced Continuous Operation
In applications where fixed frequency operation is more
critical than low current efficiency, and where the lowest output ripple is desired, forced continuous operation
should be used. Forced continuous operation can be
enabled by tying the MODE_PLLIN pin to GND. In this
mode, inductor current is allowed to reverse during low
output loads, the COMP voltage is in control of the current
comparator threshold throughout, and the top MOSFET
always turns on with each oscillator pulse. During startup, forced continuous mode is disabled and inductor
current is prevented from reversing until the LTM4620’s
output voltage is in regulation. Either regulator can be
configured for forced continuous mode.
Multiphase Operation
For output loads that demand more than 13A of current,
two outputs in LTM4620 or even multiple LTM4620s can
be paralleled to run out of phase to provide more output
current without increasing input and output voltage ripple.
The MODE_PLLIN pin allows the LTM4620 to synchronize
to an external clock (between 400kHz and 780kHz) and
the internal phase-locked loop allows the LTM4620 to
lock onto an incoming clock phase as well. The CLKOUT
signal can be connected to the MODE_PLLIN pin of the
following stage to line up both the frequency and the
phase of the entire system. Tying the PHASMD pin to
INTVCC, SGND, or (floating) generates a phase difference
(between MODE_PLLIN and CLKOUT) of 120 degrees, 60
degrees, or 90 degrees respectively. A total of 12 phases
can be cascaded to run simultaneously with respect to
each other by programming the PHASMD pin of each
LTM4620 channel to different levels. Figure 3 shows a
2-phase design, 4-phase design and a 6-phase design
example for clock phasing with the PHASMD table.
4620fc
For more information www.linear.com/LTM4620
LTM4620
APPLICATIONS INFORMATION
2-PHASE DESIGN
PHASMD
FLOAT
CLKOUT
0 PHASE
MODE_PLLIN
VOUT1
VOUT2
SGND
FLOAT
CONTROLLER1
0
0
0
CONTROLLER2
180
180
240
CLKOUT
60
90
120
180 PHASE
INTVCC
PHASMD
4-PHASE DESIGN
90 DEGREE
CLKOUT
0 PHASE
FLOAT
CLKOUT
MODE_PLLIN
VOUT1
VOUT2
180 PHASE
90 PHASE
FLOAT
PHASMD
MODE_PLLIN
VOUT1
VOUT2
270 PHASE
PHASMD
6-PHASE DESIGN
60 DEGREE
60 DEGREE
CLKOUT
0 PHASE
SGND
CLKOUT
MODE_PLLIN
VOUT1
PHASMD
VOUT2
180 PHASE
60 PHASE
SGND
CLKOUT
MODE_PLLIN
VOUT1
VOUT2
240 PHASE
PHASMD
120 PHASE
FLOAT
MODE_PLLIN
VOUT1
VOUT2
300 PHASE
PHASMD
4620 F03
Figure 3. Examples of 2-Phase, 4-Phase, and 6-Phase Operation with PHASMD Table
A multiphase power supply significantly reduces the
amount of ripple current in both the input and output
capacitors. The RMS input ripple current is reduced by,
and the effective ripple frequency is multiplied by, the
number of phases used (assuming that the input voltage
is greater than the number of phases used times the output voltage). The output ripple amplitude is also reduced
by the number of phases used when all of the outputs
are tied together to achieve a single high output current
design.
The LTM4620 device is an inherently current mode controlled device, so parallel modules will have very good
current sharing. This will balance the thermals on the
design. Figure 26 shows an example of parallel operation
and pin connection.
4620fc
For more information www.linear.com/LTM4620
15
LTM4620
APPLICATIONS INFORMATION
Input RMS Ripple Current Cancellation
Application Note 77 provides a detailed explanation of multiphase operation. The input RMS ripple current cancellation mathematical derivations are presented, and a graph
is displayed representing the RMS ripple current reduction
as a function of the number of interleaved phases. Figure 4
shows this graph.
Frequency Selection and Phase-Locked Loop
(MODE_PLLIN and fSET Pins)
The LTM4620 device is operated over a range of frequencies to improve power conversion efficiency. It is recommended to operate the lower output voltages or lower
duty cycle conversions at lower frequencies to improve
efficiency by lowering power MOSFET switching losses.
Higher output voltages or higher duty cycle conversions
can be operated at higher frequencies to limit inductor
ripple current. The efficiency graphs will show an operating frequency chosen for that condition.
0.60
1-PHASE
2-PHASE
3-PHASE
4-PHASE
6-PHASE
0.55
0.50
RMS INPUT RIPPLE CURRENT
DC LOAD CURRENT
0.45
0.40
0.35
0.30
0.25
0.20
0.15
0.10
0.05
0
0.1 0.15
0.2 0.25 0.3 0.35 0.4 0.45 0.5 0.55 0.6 0.65 0.7 0.75 0.8 0.85 0.9
DUTY CYCLE (VOUT/VIN)
4620 F04
Figure 4. Input RMS Current Ratios to DC Load Current as a Function of Duty Cycle
16
4620fc
For more information www.linear.com/LTM4620
LTM4620
APPLICATIONS INFORMATION
Minimum On-Time
900
Minimum on-time tON is the smallest time duration that
the LTM4620 is capable of turning on the top MOSFET on
either channel. It is determined by internal timing delays,
and the gate charge required to turn on the top MOSFET.
Low duty cycle applications may approach this minimum
on-time limit and care should be taken to ensure that:
800
FREQUENCY (kHz)
700
600
500
400
300
200
100
0
0
0.5
1
1.5
fSET PIN VOLTAGE (V)
2
2.5
4620 F05
Figure 5. Operating Frequency vs fSET Pin Voltage
The LTM4620 switching frequency can be set with an
external resistor from the fSET pin to SGND. An accurate
10µA current source into the resistor will set a voltage that
programs the frequency or a DC voltage can be applied.
Figure 5 shows a graph of frequency setting verses programming voltage. An external clock can be applied to
the MODE_PLLIN pin from 0V to INTVCC over a frequency
range of 400kHz to 780kHz. The clock input high threshold is 1.6V and the clock input low threshold is 1V. The
LTM4620 has the PLL loop filter components on board.
The frequency setting resistor should always be present
to set the initial switching frequency before locking to an
external clock. Both regulators will operate in continuous
mode while being externally clocked.
The output of the PLL phase detector has a pair of complementary current sources that charge and discharge the
internal filter network. When the external clock is applied,
the fSET frequency resistor is disconnected with an internal switch, and the current sources control the frequency
adjustment to lock to the incoming external clock. When
no external clock is applied, then the internal switch is on,
thus connecting the external fSET frequency set resistor
for free run operation.
VOUT
> tON(MIN)
VIN • FREQ
If the duty cycle falls below what can be accommodated
by the minimum on-time, the controller will begin to skip
cycles. The output voltage will continue to be regulated,
but the output ripple will increase. The on-time can be
increased by lowering the switching frequency. A good
rule of thumb is to keep on-time longer than 110ns.
Output Voltage Tracking
Output voltage tracking can be programmed externally
using the TRACK pins. The output can be tracked up and
down with another regulator. The master regulator’s output is divided down with an external resistor divider that
is the same as the slave regulator’s feedback divider to
implement coincident tracking. The LTM4620 uses an
accurate 60.4k resistor internally for the top feedback
resistor for each channel. Figure 6 shows an example of
coincident tracking.
60.4k
SLAVE = 1+
• VTRACK
RTA
VTRACK is the track ramp applied to the slave’s track pin.
VTRACK has a control range of 0V to 0.6V, or the internal
reference voltage. When the master’s output is divided
down with the same resistor values used to set the slave’s
output, then the slave will coincident track with the master
until it reaches its final value. The master will continue to
its final value from the slave’s regulation point. Voltage
tracking is disabled when VTRACK is more than 0.6V. RTA
in Figure 6 will be equal to the RFB for coincident tracking.
Figure 7 shows the coincident tracking waveforms.
4620fc
For more information www.linear.com/LTM4620
17
LTM4620
APPLICATIONS INFORMATION
INTVCC
C10
4.7µF
R2
10k
PGOOD
MODE_PLLIN
7V TO 16V INTERMEDIATE BUS
C4
22µF
25V
R1*
10k
C3
22µF
25V
C2
22µF
25V
C1
22µF
25V
R6
10k
CLKOUT INTVCC EXTVCC
PGOOD1
VOUT1
VIN
VOUTS1
SW1
TEMP
RUN2
CSS
0.1µF
VFB2
LTM4620
COMP2
TRACK2
RTB
60.4k
1.5V
RTA
60.4k
VOUTS2
VOUT2
f SET
PGOOD2
SGND
VOUT1
1.5V AT 13A
GND
DIFFP
DIFFN
DIFFOUT
40.2k
SLAVE
SW2 PGOOD
PHASMD
R4
121k
RFB
60.4k
COMP1
TRACK1
MASTER
C8
470µF
6.3V
VFB1
RUN1
D1*
5.1V ZENER
C6
100µF
6.3V
C5
100µF
6.3V
C7
470µF
6.3V
VOUT2
1.2V AT 13A
INTVCC
R9
10k
RAMP TIME
tSOFTSTART = (CSS /1.3µA) • 0.6V
* PULL-UP RESISTOR AND ZENER ARE OPTIONAL.
4620 F06
Figure 6. Example of Output Tracking Application Circuit
OUTPUT VOLTAGE
MASTER OUTPUT
SLAVE OUTPUT
TIME
4620 F07
Figure 7. Output Coincident Tracking Waveform
18
4620fc
For more information www.linear.com/LTM4620
LTM4620
APPLICATIONS INFORMATION
The TRACK pin can be controlled by a capacitor placed
on the regulator TRACK pin to ground. A 1.3µA current
source will charge the TRACK pin up to the reference voltage and then proceed up to INTVCC. After the 0.6V ramp,
the TRACK pin will no longer be in control, and the internal
voltage reference will control output regulation from the
feedback divider. Foldback current limit is disabled during
this sequence of turn-on during tracking or soft-starting.
The TRACK pins are pulled low when the RUN pin is below
1.2V. The total soft-start time can be calculated as:
tSOFT-START
C
= SS • 0.6V
1.3µA
Regardless of the mode selected by the MODE_PLLIN
pin, the regulator channels will always start in pulseskipping mode up to TRACK = 0.5V. Between TRACK =
0.5V and 0.54V, it will operate in forced continuous mode
and revert to the selected mode once TRACK > 0.54V. In
order to track with another channel once in steady state
operation, the LTM4620 is forced into continuous mode
operation as soon as VFB is below 0.54V regardless of the
setting on the MODE_PLLIN pin.
Ratiometric tracking can be achieved by a few simple calculations and the slew rate value applied to the master’s
TRACK pin. As mentioned above, the TRACK pin has a
control range from 0 to 0.6V. The master’s TRACK pin
slew rate is directly equal to the master’s output slew rate
in Volts/Time. The equation:
MR
• 60.4k = RTB
SR
where MR is the master’s output slew rate and SR is the
slave’s output slew rate in Volts/Time. When coincident
tracking is desired, then MR and SR are equal, thus RTB
is equal the 60.4k. RTA is derived from equation:
RTA =
0.6V
V
V
VFB
+ FB − TRACK
60.4k RFB
RTB
where VFB is the feedback voltage reference of the regulator, and VTRACK is 0.6V. Since RTB is equal to the 60.4k
top feedback resistor of the slave regulator in equal slew
rate or coincident tracking, then RTA is equal to RFB with
VFB = VTRACK. Therefore RTB = 60.4k, and RTA = 60.4k in
Figure 6.
In ratiometric tracking, a different slew rate maybe desired
for the slave regulator. RTB can be solved for when SR is
slower than MR. Make sure that the slave supply slew
rate is chosen to be fast enough so that the slave output
voltage will reach it final value before the master output.
For example, MR = 1.5V/1ms, and SR = 1.2V/1ms. Then
RTB = 76.8k. Solve for RTA to equal to 49.9k.
Each of the TRACK pins will have the 1.3µA current source
on when a resistive divider is used to implement tracking
on that specific channel. This will impose an offset on the
TRACK pin input. Smaller values resistors with the same
ratios as the resistor values calculated from the above
equation can be used. For example, where the 60.4k is
used then a 6.04k can be used to reduce the TRACK pin
offset to a negligible value.
Power Good
The PGOOD pins are open drain pins that can be used to
monitor valid output voltage regulation. This pin monitors
a ±10% window around the regulation point. A resistor
can be pulled up to a particular supply voltage no greater
than 6V maximum for monitoring.
Stability Compensation
The module has already been internally compensated for
all output voltages. Table 4 is provided for most application requirements. LTpowerCAD will be provided for other
control loop optimization.
Run Enable
The RUN pins have an enable threshold of 1.4V maximum,
typically 1.25V with 150mV of hysteresis. They control the
turn on each of the channels and INTVCC. These pins can be
pulled up to VIN for 5V operation, or a 5V Zener diode can be
placed on the pins and a 10k to 100k resistor can be placed
up to higher than 5V input for enabling the channels. The
RUN pins can also be used for output voltage sequencing.
In parallel operation the RUN pins can be tie together
4620fc
For more information www.linear.com/LTM4620
19
LTM4620
APPLICATIONS INFORMATION
and controlled from a single control. See the Typical
Application circuits in Figure 23.
INTVCC and EXTVCC
The LTM4620 module has an internal 5V low dropout
regulator that is derived from the input voltage. This regulator is used to power the control circuitry and the power
MOSFET drivers. This regulator can source up to 70mA,
and typically uses ~30mA for powering the device at the
maximum frequency. This internal 5V supply is enabled
by either RUN1 or RUN2.
EXTVCC allows an external 5V supply to power the
LTM4620 and reduce power dissipation from the internal
low dropout 5V regulator. The power loss savings can be
calculated by:
(VIN – 5V) • 30mA = PLOSS
EXTVCC has a threshold of 4.7V for activation, and a maximum rating of 6V. When using a 5V input, connect this
5V input to EXTVCC also to maintain a 5V gate drive level.
EXTVCC must sequence on after VIN, and EXTVCC must
sequence off before VIN.
Differential Remote Sense Amplifier
An accurate differential remote sense amplifier is provided
to sense low output voltages accurately at the remote
load points. This is especially true for high current loads.
The amplifier can be used on one of the two channels, or
on a single parallel output. It is very important that the
DIFFP and DIFFN are connected properly at the output,
and DIFFOUT is connected to either VOUTS1 or VOUTS2.
In parallel operation, the DIFFP and DIFFN are connected
properly at the output, and DIFFOUT is connected to
one of the VOUTS pins. Review the parallel schematics in
Figure 24 and review Figure 2.
SW Pins
The SW pins are generally for testing purposes by monitoring these pins. These pins can also be used to dampen
out switch node ringing caused by LC parasitic in the
switched current paths. Usually a series R-C combination
is used called a snubber circuit. The resistor will dampen
the resonance and the capacitor is chosen to only affect
the high frequency ringing across the resistor. If the stray
20
inductance or capacitance can be measured or approximated then a somewhat analytical technique can be used
to select the snubber values. The inductance is usually
easier to predict. It combines the power path board inductance in combination with the MOSFET interconnect bond
wire inductance.
First the SW pin can be monitored with a wide bandwidth
scope with a high frequency scope probe. The ring frequency can be measured for its value. The impedance Z
can be calculated:
Z (L) = 2πfL,
where f is the resonant frequency of the ring, and L is the
total parasitic inductance in the switch path. If a resistor
is selected that is equal to Z, then the ringing should be
dampened. The snubber capacitor value is chosen so that
its impedance is equal to the resistor at the ring frequency.
Calculated by: Z (C) = 1/(2πfC). These values are a good
place to start with. Modification to these components
should be made to attenuate the ringing with the least
amount of power loss.
Temperature Monitoring (TEMP)
A diode connected PNP transistor is used for the TEMP
monitor function by monitoring its voltage over temperature. The temperature dependence of this diode can be
understood in the equation:
D = nVTIn
ID
,
IS
Where VT is the thermal voltage (kT/q), and n, the ideality
factor is 1 for the two diode connected PNPs being used
in the LTM4620. Since ID has an exponential temperature dependence that can be understood from the typical
empirical equation for IS:
IS = I0 exp (–VG0/VT),
Where Io is some process and geometry dependent current (Io is typically around 20 orders of magnitude larger
than IS at room temperature, so Io is much larger than typical values of ID), and VG0 is the band gap voltage of 1.2V
extrapolated to absolute zero of –273°C Kelvin. Figure 8
shows a plot of the diode temperature characteristic of
4620fc
For more information www.linear.com/LTM4620
LTM4620
APPLICATIONS INFORMATION
If we take the IS equation and substitute into the VD equation, then we get:
VD = VG0 –
Kt I0
kT
ln
,V =
q ID T q
The expression shows that the junction voltage of the PNP
connected diode decreases linearly if Io were constant
from a value VG0 of 1.2V at absolute zero to a decreasing
value with increased temperature.
If we take this equation and differentiate it with respect to
temperature T, then:
dVD
= – ( VG0 – VD) / T
dT
This
dVD
dT
change as a function of temperature is the typical
~–2mV/°C. This equation is simplified for the first order
derivation.
Solving for T, T = –(VG0 – VD)/ dVD provide the
temperature.
1st Example: Figure 4 for 27°C, or 300°C Kelvin the diode
voltage is 0.598V, thus, 300°C = –(1200mV – 598mV)/
–2mV/°C)
2nd Example: Figure 4 for 75°C, or 350°C Kelvin the diode
voltage is 0.50V, thus, 350°C = –(1200mV – 500mV)/
–2mV/°C)
Converting the Kelvin scale to Celsius is simply taking the
Kelvin temp and subtracting –273°C Kelvin from it.
0.8
TEMP PIN DIODE VOLTAGE (V)
the diode connected PNP transistor biased with a 100µA
current source. This plot would extend to the left back to
1.2V at –273°C Kelvin. This curve is stop at –55°C due to
the test system limits.
ID = 100µA
0.7
0.6
0.5
0.4
0.3
–50
–25
50
25
0
75
TEMPERATURE (°C)
100
125
4620 F08
Figure 8. Diode Voltage VD vs Temperature
T(°C) for Different Bias Currents
The diode connected PNP transistor can be pulled up to
VIN with a resistor to set the current to 100µA for using
this diode connected transistor as a general temperature
monitor by monitoring the diode voltage drop with temperature. See Figure 24 for an example.
Thermal Considerations and Output Current Derating
The thermal resistances reported in the Pin Configuration
section of the data sheet are consistent with those parameters defined by JESD 51-12 and are intended for use
with finite element analysis (FEA) software modeling
tools that leverage the outcome of thermal modeling,
simulation, and correlation to hardware evaluation performed on a µModule package mounted to a hardware
test board defined by JESD 51-9 (“Test Boards for Area
Array Surface Mount Package Thermal Measurements”).
The motivation for providing these thermal coefficients is
found in JESD 51-12 (“Guidelines for Reporting and Using
Electronic Package Thermal Information”).
A typical forward voltage is measured and placed in the
electrical characteristics section of the data sheet, and
Figure 8 is the plot of this forward voltage. Measure this
forward voltage at 27°C to establish a reference point.
Then use the above expression while measuring the forward voltage over temperature will provide a general temperature monitor.
4620fc
For more information www.linear.com/LTM4620
21
LTM4620
APPLICATIONS INFORMATION
Many designers may opt to use laboratory equipment and
a test vehicle such as the demo board to anticipate the
µModule regulator’s thermal performance in their application at various electrical and environmental operating
conditions to compliment any FEA activities. Without
FEA software, the thermal resistances reported in the
Pin Configuration section are in-and-of themselves not
relevant to providing guidance of thermal performance;
instead, the derating curves provided in the data sheet can
be used in a manner that yields insight and guidance pertaining to one’s application-usage, and can be adapted to
correlate thermal performance to one’s own application.
The Pin Configuration section gives four thermal coefficients explicitly defined in JESD 51-12; these coefficients
are quoted or paraphrased below:
1. θJA, the thermal resistance from junction to ambient,
is the natural convection junction-to-ambient air thermal resistance measured in a one cubic foot sealed
enclosure. This environment is sometimes referred to
as “still air” although natural convection causes the
air to move. This value is determined with the part
mounted to a JESD 51-9 defined test board, which
does not reflect an actual application or viable operating condition.
2. θJCbottom, the thermal resistance from junction to the
bottom of the product case, is determined with all
of the component power dissipation flowing through
the bottom of the package. In the typical µModule,
the bulk of the heat flows out the bottom of the package, but there is always heat flow out into the ambient environment. As a result, this thermal resistance
value may be useful for comparing packages but
the test conditions don’t generally match the user’s
application.
3. θJCtop, the thermal resistance from junction to top of
the product case, is determined with nearly all of the
component power dissipation flowing through the top
of the package. As the electrical connections of the
typical µModule are on the bottom of the package, it
is rare for an application to operate such that most of
the heat flows from the junction to the top of the part.
22
As in the case of θJCbottom, this value may be useful
for comparing packages but the test conditions don’t
generally match the user’s application.
4. θJB, the thermal resistance from junction to the
printed circuit board, is the junction-to-board thermal
resistance where almost all of the heat flows through
the bottom of the µModule and into the board, and
is really the sum of the θJCbottom and the thermal
resistance of the bottom of the part through the solder
joints and through a portion of the board. The board
temperature is measured a specified distance from
the package, using a two sided, two layer board. This
board is described in JESD 51-9.
A graphical representation of the aforementioned thermal resistances is given in Figure 9; blue resistances are
contained within the µModule regulator, whereas green
resistances are external to the µModule package.
As a practical matter, it should be clear to the reader that
no individual or sub-group of the four thermal resistance
parameters defined by JESD 51-12 or provided in the
Pin Configuration section replicates or conveys normal
operating conditions of a µModule regulator. For example,
in normal board-mounted applications, never does 100%
of the device’s total power loss (heat) thermally conduct
exclusively through the top or exclusively through bottom of the µModule package—as the standard defines
for θJCtop and θJCbottom, respectively. In practice, power
loss is thermally dissipated in both directions away from
the package—granted, in the absence of a heat sink and
airflow, a majority of the heat flow is into the board.
Within the LTM4620, be aware there are multiple power
devices and components dissipating power, with a consequence that the thermal resistances relative to different junctions of components or die are not exactly linear
with respect to total package power loss. To reconcile this
complication without sacrificing modeling simplicity—
but also, not ignoring practical realities—an approach
has been taken using FEA software modeling along with
laboratory testing in a controlled-environment chamber
to reasonably define and correlate the thermal resistance
4620fc
For more information www.linear.com/LTM4620
LTM4620
APPLICATIONS INFORMATION
values supplied in this data sheet: (1) Initially, FEA software is used to accurately build the mechanical geometry
of the LTM4620 and the specified PCB with all of the correct material coefficients along with accurate power loss
source definitions; (2) this model simulates a softwaredefined JEDEC environment consistent with JESD 51-12
to predict power loss heat flow and temperature readings
at different interfaces that enable the calculation of the
JEDEC-defined thermal resistance values; (3) the model
and FEA software is used to evaluate the LTM4620 with
heat sink and airflow; (4) having solved for and analyzed
these thermal resistance values and simulated various
operating conditions in the software model, a thorough
laboratory evaluation replicates the simulated conditions
with thermocouples within a controlled-environment
chamber while operating the device at the same power
loss as that which was simulated. An outcome of this
process and due diligence yields a set of derating curves
provided in other sections of this data sheet. After these
laboratory tests have been performed, then the θJB and
θBA are summed together to correlate quite well with the
LTM4620 model with no airflow or heat sinking in a properly define chamber. This θJB + θBA value is shown in the
Pin Configuration section and should accurately equal the
θJA value because approximately 100% of power loss
flows from the junction through the board into ambient
with no airflow or top mounted heat sink. Each system has
its own thermal characteristics, therefore thermal analysis
must be performed by the user in a particular system.
The LTM4620 has been designed to effectively remove
heat from both the top and bottom of the package. The
bottom substrate material has very low thermal resistance
to the printed circuit board and the exposed top metal is
thermally connected to the power devices and the power
inductors. An external heat sink can be applied to the top of
the device for excellent heat sinking with airflow. Basically
all power dissipating devices are mounted directly to the
substrate and the top exposed metal. This provides two
low thermal resistance paths to remove heat.
JUNCTION-TO-AMBIENT RESISTANCE (JESD 51-9 DEFINED BOARD)
JUNCTION-TO-CASE (TOP)
RESISTANCE
CASE (TOP)-TO-AMBIENT
RESISTANCE
JUNCTION-TO-BOARD RESISTANCE
JUNCTION
JUNCTION-TO-CASE
CASE (BOTTOM)-TO-BOARD
(BOTTOM) RESISTANCE
RESISTANCE
AMBIENT
BOARD-TO-AMBIENT
RESISTANCE
4620 F10
µMODULE DEVICE
Figure 9. Graphical Representation of JESD 51-12 Thermal Coefficients
4620fc
For more information www.linear.com/LTM4620
23
LTM4620
APPLICATIONS INFORMATION
Figure 10 shows a modeled temperature plot of the
LTM4620 with BGA heat sink and 200LFM airflow with
4.7W of internal dissipation.
Figure 11 shows a modeled temperature plot of the
LTM4620 with no heat sink and 200LFM airflow with
4.7W of internal dissipation.
Figure 10. LTM4620 12V to 1.2V at 26A with
200LFM, External Heat Sink
These plots equate to a paralleled 1.2V at 26A design
operating at 86% efficiency.
Safety Considerations
The LTM4620 modules do not provide isolation from VIN
to VOUT. There is no internal fuse. If required, a slow blow
fuse with a rating twice the maximum input current needs
to be provided to protect each unit from catastrophic
failure.
The fuse or circuit breaker should be selected to limit the
current to the regulator during overvoltage in case of an
internal top MOSFET fault. If the internal top MOSFET fails,
then turning it off will not resolve the overvoltage, thus
the internal bottom MOSFET will turn on indefinitely trying
to protect the load. Under this fault condition, the input
voltage will source very large currents to ground through
the failed internal top MOSFET and enabled internal bottom MOSFET. This can cause excessive heat and board
damage depending on how much power the input voltage
can deliver to this system. A fuse or circuit breaker can
be used as a secondary fault protector in this situation.
The device does support over current protection. A temperature diode is provided for monitoring internal temperature, and can be used to detect the need for thermal
shutdown that can be done by controlling the RUN pin.
Power Derating
Figure 11. LTM4620 12V to 1.2V at 26A with
200LFM, No External Heat Sink
24
The 1.0V and 2.5V power loss curves in Figures 12 and 13
can be used in coordination with the load current derating
curves in Figures 14 to 21 for calculating an approximate
θJA thermal resistance for the LTM4620 with various heat
sinking and airflow conditions. The power loss curves are
taken at room temperature, and are increased with a 1.35
to 1.4 multiplicative factor at 125°C. These factors come
from the fact that the power loss of the regulator increases
about 45% from 25°C to 150°C, thus a 50% spread over
4620fc
For more information www.linear.com/LTM4620
LTM4620
APPLICATIONS INFORMATION
125°C delta equates to ~0.35%/°C loss increase. A 125°C
maximum junction minus 25°C room temperature equates
to a 100°C increase. This 100°C increase multiplied by
0.35%/°C equals a 35% power loss increase at the 125°C
junction, thus the 1.35 multiplier.
accurate due to the fact that the ambient temperature environment is controlled better with airflow. As an example
in Figure 15, the load current is derated to ~22A at ~90°C
with 200LFM of airflow and the power loss for the 12V to
1.0V at 22A output is a ~5.94W loss.
The derating curves are plotted with VOUT1 and VOUT2 in
parallel single output operation starting at 26A of load
with low ambient temperature. The output voltages are
1.0V and 2.5V. These are chosen to include the lower
and higher output voltage ranges for correlating the thermal resistance. Thermal models are derived from several
temperature measurements in a controlled temperature
chamber along with thermal modeling analysis.
The 5.94W loss is calculated with the ~4.4W room temperature loss from the 12V to 1.0V power loss curve at
22A, and the 1.35 multiplying factor at 125°C ambient.
If the 90°C ambient temperature is subtracted from the
120°C junction temperature, then the difference of 30°C
divided by 5.94W equals a 5.1°C/W θJA thermal resistance. Table 2 specifies a 5.5°C/W value which is pretty
close. Tables 2 and 3 provide equivalent thermal resistances for 1.0V and 2.5V outputs with and without airflow
and heat sinking.
The junction temperatures are monitored while ambient
temperature is increased with and without airflow. The
power loss increase with ambient temperature change
is factored into the derating curves. The junctions are
maintained at ~120°C maximum while lowering output
current or power while increasing ambient temperature.
The decreased output current will decrease the internal
module loss as ambient temperature is increased.
The monitored junction temperature of 120°C minus the
ambient operating temperature specifies how much temperature rise can be allowed. As an example in Figure 14,
the load current is derated to ~19A at ~80°C with no air
or heat sink and the power loss for the 12V to 1.0V at
19A output is a ~5.1W loss. The 5.1W loss is calculated
with the ~3.75W room temperature loss from the 12V to
1.0V power loss curve at 19A, and the 1.35 multiplying
factor at 125°C ambient. If the 80°C ambient temperature
is subtracted from the 120°C junction temperature, then
the difference of 40°C divided by 5.1W equals a 7.8°C/W
θJA thermal resistance. Table 2 specifies a 6.5 to 7°C/W
value which is pretty close. The airflow graphs are more
The derived thermal resistances in Tables 2 and 3 for
the various conditions can be multiplied by the calculated power loss as a function of ambient temperature to
derive temperature rise above ambient, thus maximum
junction temperature. Room temperature power loss can
be derived from the efficiency curves and adjusted with
the above ambient temperature multiplicative factors. The
printed circuit board is a 1.6mm thick four layer board
with two ounce copper for the two outer layers and one
ounce copper for the two inner layers. The PCB dimensions are 101mm × 114mm. The BGA heat sinks are listed
in Table 3.
Layout Checklist/Example
The high integration of LTM4620 makes the PCB board
layout very simple and easy. However, to optimize its
electrical and thermal performance, some layout considerations are still necessary.
• Use large PCB copper areas for high current paths,
including VIN, GND, VOUT1 and VOUT2. It helps to minimize the PCB conduction loss and thermal stress.
4620fc
For more information www.linear.com/LTM4620
25
LTM4620
APPLICATIONS INFORMATION
Table 2. 1.0V Output
DERATING CURVE
Figures 14, 15
Figures 14, 15
Figures 14, 15
Figures 16, 17
Figures 16, 17
Figures 16, 17
VIN (V)
5, 12
5, 12
5, 12
5, 12
5, 12
5, 12
POWER LOSS CURVE
Figure 12
Figure 12
Figure 12
Figure 12
Figure 12
Figure 12
AIRFLOW (LFM)
0
200
400
0
200
400
HEAT SINK
None
None
None
BGA Heat Sink
BGA Heat Sink
BGA Heat Sink
LGA
θJA (°C/W)
6.5 to 7
5.5
5
6.5
5
4
BGA
θJA (°C/W)
6.5 to 7
5.5
5
6.5
5
4
VIN (V)
5, 12
5, 12
5, 12
5, 12
5, 12
5, 12
POWER LOSS CURVE
Figure 13
Figure 13
Figure 13
Figure 13
Figure 13
Figure 13
AIRFLOW (LFM)
0
200
400
0
200
400
HEAT SINK
None
None
None
BGA Heat Sink
BGA Heat Sink
BGA Heat Sink
LGA
θJA (°C/W)
6.5 to 7
5.5 to 6
4.5
6.5 to 7
4
3.5
BGA
θJA (°C/W)
6.5 to 7
5.5 to 6
4.5
6.5 to 7
4
3.5
Table 3. 2.5V Output
DERATING CURVE
Figures 18, 19
Figures 18, 19
Figures 18, 19
Figures 20, 21
Figures 20, 21
Figures 20, 21
HEAT SINK MANUFACTURER
PART NUMBER
WEBSITE
Aavid Thermalloy
375424B00034G
www.aavid.com
Cool Innovations
4-050503P to 4-050508P
www.coolinnovations.com
26
4620fc
For more information www.linear.com/LTM4620
LTM4620
APPLICATIONS INFORMATION
Table 4. Output Voltage Response vs Component Matrix (Refer to Figure 23) 0A to 7A Load Step Typical Measured Values
VENDORS
TDK, COUT1 Ceramic
Murata, COUT1 Ceramic
AVX, COUT1 Ceramic
VALUE
100µF 6.3V
100µF 6.3V
100µF 6.3V
PART NUMBER
C4532X5R0J107MZ
GRM32ER60J107M
18126D107MAT
Sanyo POSCAP, COUT2 Bulk
470µF 4V
4TPF470ML
Sanyo POSCAP, COUT2 Bulk
470µF 6.3V
6TPD470M
Sanyo, CIN Bulk
56µF 25V
25SVP56M
VOUT
CIN
COUT1
COUT2
CFF
CBOT
CIN
(pF)
(pF)
(V) (CERAMIC) (BULK)** (CERAMIC) (BULK)
1
22µF × 3
56µF
100µF
470µF × 2 100
None
1
22µF × 3
56µF
100µF
470µF × 2 100
None
1
22µF × 3
56µF
100µF × 3 470µF × 2 100
None
1
22µF × 3
56µF
100µF × 3 470µF × 2 100
None
1.2
22µF × 3
56µF
100µF × 3 470µF × 2 100
None
1.2
22µF × 3
56µF
100µF × 3 470µF × 2 100
None
1.2
22µF × 3
56µF
100µF
470µF × 2 100
None
1.2
22µF × 3
56µF
100µF
470µF × 2 100
None
1.5
22µF × 3
56µF
100µF
470µF × 2 100
None
1.5
22µF × 3
56µF
100µF
470µF × 2 100
None
1.8
22µF × 3
56µF
100µF
470µF
100
None
1.8
22µF × 3
56µF
100µF
470µF
100
None
1.8
22µF × 3
56µF
100µF × 3
None
150
None
1.8
22µF × 3
56µF
100µF × 3
None
150
None
2.5
22µF × 3
56µF
100µF × 3
None
220
None
2.5
22µF × 3
56µF
100µF × 3
None
220
None
22µF × 3
56µF
100µF
470µF
150
None
2.5
2.5
22µF × 3
56µF
100µF
470µF
150
None
**Bulk capacitance is optional if VIN has very low input impedance.
CCOMP
(pF)
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
VIN
(V)
5
12
5
12
5
12
5
12
5
12
5
12
5
12
5
12
5
12
P-P
DEVIATION RECOVERY LOAD
DROOP AT 7A LOAD
TIME
STEP
(mV)
STEP (mV)
(µs)
(A/µs)
65
130
30
7
65
130
30
7
60
120
30
7
60
120
30
7
65
130
30
7
65
130
30
7
68
136
35
7
68
136
30
7
70
140
35
7
70
140
30
7
75
150
30
7
75
150
30
7
100
200
15
7
100
200
18
7
100
200
20
7
100
200
20
7
85
170
30
7
85
170
30
7
RFB
(kΩ)
90.9
90.9
90.9
90.9
60.4
60.4
60.4
60.4
40.2
40.2
30.2
30.2
30.2
30.2
19.1
19.1
19.1
19.1
FREQ
400
400
400
400
500
500
500
500
550
550
600
600
600
600
750
750
750
750
4620fc
For more information www.linear.com/LTM4620
27
LTM4620
APPLICATIONS INFORMATION
6
5
7
4
3
2
5
4
3
1
0
0 2 4 6 8 10 12 14 16 18 20 22 24 26
LOAD CURRENT (A)
26
24
22
20
18
16
14
12
10
8
6
4
2
0
0 2 4 6 8 10 12 14 16 18 20 22 24 26
LOAD CURRENT (A)
4620 F12
4620 F13
Figure 12. 1.0V Power Loss Curve
Figure 13. 2.5V Power Loss Curve
LOAD CURRENT (A)
LOAD CURRENT (A)
6
2
1
0
5VIN, 2.5VOUT
12VIN, 2.5VOUT
8
POWER LOSS (W)
POWER LOSS (W)
9
5VIN, 1VOUT
12VIN , 1VOUT
400LFM
200LFM
0LFM
0
80
20
40
60
100
AMBIENT TEMPERATURE (°C)
120
26
24
22
20
18
16
14
12
10
8
6
4
2
0
400LFM
200LFM
0LFM
0
80
20
40
60
100
AMBIENT TEMPERATURE (°C)
4620 F14
4620 F15
Figure 15. 5V to 1V Derating
Curve, No Heat Sink
CH1 AND CH2 COMBINED LOAD CURRENT (A)
LOAD CURRENT (A)
Figure 14. 12V to 1V Derating
Curve, No Heat Sink
26
24
22
20
18
16
14
12
10
8
6
4
2
0
400LFM
200LFM
0LFM
0
80
20
40
60
100
AMBIENT TEMPERATURE (°C)
120
26
24
22
20
18
16
14
12
10
8
6
4
2
0
400LFM
200LFM
0LFM
0
80
20
40
60
100
AMBIENT TEMPERATURE (°C)
28
120
4620 F17
4620 F16
Figure 16. 12V to 1V Derating
Curve, BGA Heat Sink
120
Figure 17. 5V to 1V Derating
Curve, BGA Heat Sink
4620fc
For more information www.linear.com/LTM4620
LTM4620
26
24
22
20
18
16
14
12
10
8
6
4
2
0
LOAD CURRENT (A)
LOAD CURRENT (A)
APPLICATIONS INFORMATION
400LFM
200LFM
0LFM
0
80
20
40
60
100
AMBIENT TEMPERATURE (°C)
120
26
24
22
20
18
16
14
12
10
8
6
4
2
0
400LFM
200LFM
0LFM
0
80
20
40
60
100
AMBIENT TEMPERATURE (°C)
4620 F19
4620 F18
Figure 19. 5V to 2.5V Derating
Curve, No Heat Sink
LOAD CURRENT (A)
LOAD CURRENT (A)
Figure 18. 12V to 2.5V Derating
Curve, No Heat Sink
26
24
22
20
18
16
14
12
10
8
6
4
2
0
400LFM
200LFM
0LFM
0
80
20
40
60
100
AMBIENT TEMPERATURE (°C)
120
26
24
22
20
18
16
14
12
10
8
6
4
2
0
400LFM
200LFM
0LFM
0
80
20
40
60
100
AMBIENT TEMPERATURE (°C)
4620 F20
Figure 20. 12V to 2.5V Derating
Curve, BGA Heat Sink
120
120
4620 F21
Figure 21. 5V to 2.5V Derating
Curve, BGA Heat Sink
4620fc
For more information www.linear.com/LTM4620
29
LTM4620
APPLICATIONS INFORMATION
• Place high frequency ceramic input and output capacitors next to the VIN, PGND and VOUT pins to minimize
high frequency noise.
• Use a separated SGND ground copper area for components connected to signal pins. Connect the SGND
to GND underneath the unit.
• Place a dedicated power ground layer underneath the
unit.
• For parallel modules, tie the VOUT, VFB, and COMP pins
together. Use an internal layer to closely connect these
pins together. The TRACK pin can be tied a common
capacitor for regulator soft-start.
• To minimize the via conduction loss and reduce module thermal stress, use multiple vias for interconnection between top layer and other power layers.
• Do not put via directly on the pad, unless they are
capped or plated over.
30
• Bring out test points on the signal pins for monitoring.
Figure 22 gives a good example of the recommended
layout.
4620fc
For more information www.linear.com/LTM4620
LTM4620
APPLICATIONS INFORMATION
LGA
CIN1
CIN2
VIN
M
L
K
GND
GND
J
H
G
COUT1
SGND
F
COUT2
E
D
C
B
A
1
2
3
4
5
6
VOUT1
7
8
9
10
11
12
GND
VOUT2
4620 F22a
CNTRL
BGA
CIN1
CIN2
VIN
M
L
K
GND
GND
J
H
G
COUT1
SGND
F
COUT2
E
D
C
B
A
1
VOUT1
2
3
4
5
6
7
8
9
10
11
12
GND
VOUT2
4620 F22b
CNTRL
Figure 22. Recommended PCB Layout
4620fc
For more information www.linear.com/LTM4620
31
+
CIN
(OPT)
32
For more information www.linear.com/LTM4620
C3
22µF
25V
D1*
5.1V ZENER
R1*
10k
C5
0.1µF
TRACK1
C2
22µF
25V
C9
0.1µF
TRACK2
C1
22µF
25V
R4
121k
R7
10k
SGND
PHASMD
fSET
TRACK2
TRACK1
RUN2
RUN1
TEMP
VIN
MODE_PLLIN
GND
DIFFP
LTM4620
CLKOUT INTVCC
DIFFN
PGOOD2
DIFFOUT
SW2
VOUT2
VOUTS2
COMP2
COMP1
VFB2
VFB1
SW1
VOUTS1
VOUT1
EXTVCC PGOOD1
R2
10k
INTVCC
R3
10k
PGOOD2
CCOMP**
PGOOD1
Figure 23. Typical 5VIN to 16VIN, 1.5V and 1.2V Outputs
* PULL-UP RESISTOR AND ZENER ARE OPTIONAL.
C4
22µF
25V
5V TO 16V INTERMEDIATE BUS
C10
4.7µF
INTVCC
COUT1
100µF
6.3V
RFB2*
60.4k
+
RFB1*
40.2k
CFF*
COUT2
470µF
6.3V
COUT2
470µF
6.3V
VOUT1
1.5V AT 13A
CBOT
SEE TABLE 4**
+
4620 F23
VOUT2
1.2V AT 13A
COUT1
100µF
6.3V
LTM4620
TYPICAL APPLICATIONS
4620fc
C3
22µF
25V
For more information www.linear.com/LTM4620
TRACK1
C11
22µF
25V
C2
22µF
25V
C9
0.1µF
R4
121k
C1
22µF
25V
= RT
R2
5k
INTVCC
SGND
PHASMD
fSET
TRACK2
TRACK1
RUN1
RUN2
GND
DIFFP
LTM4620
DIFFN
DIFFOUT
PGOOD2
SW2
VOUT2
VOUTS2
COMP2
COMP1
VFB2
VFB1
SW1
VOUT1
VOUTS1
EXTVCC PGOOD1
C10
4.7µF
VIN
CLKOUT INTVCC
INTVCC
TEMP
MODE_PLLIN
100µA
VIN – 0.6V
PGOOD1
R5
40.2k
PGOOD1
Figure 24. LTM4620 2-Phase, 1.5V at 26A Design with Temperature Monitoring
* PULL-UP RESISTOR AND ZENER ARE OPTIONAL.
D1*
5.1V ZENER
R1*
10k
5V TO 16V INTERMEDIATE BUS
A/D
VIN
COUT1
100µF
6.3V
COUT1
100µF
6.3V
+
+
4620 F24
COUT2
470µF
6.3V
COUT2
470µF
6.3V
1.5V AT 26A
LTM4620
TYPICAL APPLICATIONS
4620fc
33
VIN
5V TO 16V
34
D1*
5.1V ZENER
C4
22µF
25V
For more information www.linear.com/LTM4620
C5
0.1µF
1.2V
R9
60.4k
C2
22µF
25V
R7
90.9k
C1
22µF
25V
R4
121k
R6
10k
SGND
PHASMD
DIFFN
DIFFOUT
PGOOD2
SW2
VOUT2
VOUTS2
fSET
COMP2
DIFFP
VFB2
COMP1
TRACK2
GND
LTM4620
VFB1
SW1
VOUTS1
VOUT1
CLKOUT INTVCC EXTVCC PGOOD1
TRACK1
RUN1
RUN2
TEMP
VIN
MODE_PLLIN
R2
10k
Figure 25. LTM4620 1.2V and 1V Output Tracking
* PULL-UP RESISTOR AND ZENER ARE OPTIONAL.
R1*
10k
C3
22µF
25V
INTERMEDIATE BUS
C10
4.7µF
INTVCC
INTVCC
R3
10k
PGOOD2
R8
90.9k
PGOOD1
COUT1
100µF
6.3V
R5
60.4k
+
COUT1
100µF
6.3V
+
4620 F25
COUT2
470µF
6.3V
COUT2
470µF
6.3V
VOUT2
1V AT 13A
VOUT1
1.2V AT 13A
LTM4620
TYPICAL APPLICATIONS
4620fc
LTM4620
TYPICAL APPLICATIONS
INTVCC
CLK1
VIN
5V TO 16V
MODE_PLLIN
INTERMEDIATE BUS
R1*
10k
C3
22µF
25V
C2
22µF
25V
C1
22µF
25V
R6
10k
CLKOUT INTVCC
C10
4.7µF
R2
5k
PGOOD1
EXTVCC PGOOD1
VIN
VOUT1
VOUTS1
SW1
VFB1
TEMP
RUN
RUN1
LTM4620
RUN2
TRACK1
D1*
5.1V ZENER
VFB2
COMP1
TRACK1
COMP2
TRACK2
COUT2
470µF
6.3V
COUT1
100µF
6.3V
+
COUT2
470µF
6.3V
VFB
R5
60.4k
COMP
VOUT2
PHASMD
SW2
PGOOD2
SGND
+
VOUTS2
fSET
R4
121k
COUT1
100µF
6.3V
GND
DIFFP
DIFFN
PGOOD1
DIFFOUT
VOUT
1.2V AT 50A
C16
4.7µF
CLK1
MODE_PLLIN
5V TO 16V INTERMEDIATE BUS
C12
22µF
25V
C15
22µF
25V
C5
22µF
25V
CLKOUT INTVCC
PGOOD1
EXTVCC PGOOD1
VOUT1
VIN
R9
10k
VOUTS1
RUN1
TRACK1
TEMP
RUN1
SW1
RUN2
VFB2
VFB1
LTM4620
TRACK1
COMP1
COUT2
470µF
6.3V
COUT1
100µF
6.3V
+
COUT2
470µF
6.3V
VFB
COMP
VOUTS2
fSET
VOUT2
PHASMD
R10
121k
* PULL-UP RESISTOR AND ZENER ARE OPTIONAL.
+
COMP2
TRACK2
C19
0.22µF
COUT1
100µF
6.3V
SW2
PGOOD2
SGND
GND
DIFFP
DIFFN
PGOOD1
DIFFOUT
INTVCC
4620 F26
Figure 26. 4-Phase, 1.2V at 50A
4620fc
For more information www.linear.com/LTM4620
35
LTM4620
PACKAGE DESCRIPTION
PACKAGE ROW AND COLUMN LABELING MAY VARY
AMONG µModule PRODUCTS. REVIEW EACH PACKAGE
LAYOUT CAREFULLY.
LTM4620 Component LGA Pinout
PIN ID
FUNCTION
PIN ID
FUNCTION
PIN ID
FUNCTION
PIN ID
FUNCTION
PIN ID
FUNCTION
PIN ID
FUNCTION
A1
VOUT1
B1
VOUT1
C1
VOUT1
D1
GND
E1
GND
F1
GND
A2
VOUT1
B2
VOUT1
C2
VOUT1
D2
GND
E2
GND
F2
GND
A3
VOUT1
B3
VOUT1
C3
VOUT1
D3
GND
E3
GND
F3
GND
A4
VOUT1
B4
VOUT1
C4
VOUT1
D4
GND
E4
GND
F4
MODE_PLLIN
A5
VOUT1
B5
VOUT1
C5
VOUT1S
D5
VFB1
E5
TRACK1
F5
RUN1
A6
GND
B6
GND
C6
fSET
D6
SGND
E6
COMP1
F6
SGND
A7
GND
B7
GND
C7
SGND
D7
VFB2
E7
COMP2
F7
SGND
A8
VOUT2
B8
VOUT2
C8
VOUT2S
D8
TRACK2
E8
DIFFP
F8
DIFFOUT
A9
VOUT2
B9
VOUT2
C9
VOUT2
D9
GND
E9
DIFFN
F9
RUN2
A10
VOUT2
B10
VOUT2
C10
VOUT2
D10
GND
E10
GND
F10
GND
A11
VOUT2
B11
VOUT2
C11
VOUT2
D11
GND
E11
GND
F11
GND
A12
VOUT2
B12
VOUT2
C12
VOUT2
D12
GND
E12
GND
F12
GND
PIN ID
FUNCTION
PIN ID
FUNCTION
PIN ID
FUNCTION
PIN ID
FUNCTION
PIN ID
FUNCTION
PIN ID
FUNCTION
G1
GND
H1
GND
J1
GND
K1
GND
L1
GND
M1
GND
G2
SW1
H2
GND
J2
VIN
K2
VIN
L2
VIN
M2
VIN
G3
GND
H3
GND
J3
VIN
K3
VIN
L3
VIN
M3
VIN
G4
PHASMD
H4
GND
J4
VIN
K4
VIN
L4
VIN
M4
VIN
G5
CLKOUT
H5
GND
J5
GND
K5
GND
L5
VIN
M5
VIN
G6
SGND
H6
GND
J6
TEMP
K6
GND
L6
VIN
M6
VIN
G7
SGND
H7
GND
J7
EXTVCC
K7
GND
L7
VIN
M7
VIN
G8
PGOOD2
H8
INTVCC
J8
GND
K8
GND
L8
VIN
M8
VIN
G9
PGOOD1
H9
GND
J9
VIN
K9
VIN
L9
VIN
M9
VIN
G10
GND
H10
GND
J10
VIN
K10
VIN
L10
VIN
M10
VIN
G11
SW2
H11
GND
J11
VIN
K11
VIN
L11
VIN
M11
VIN
G12
GND
H12
GND
J12
GND
K12
GND
L12
GND
M12
GND
36
4620fc
For more information www.linear.com/LTM4620
For more information www.linear.com/LTM4620
6.9850
5.7150
4.4450
3.1750
1.9050
0.6350
0.0000
0.6350
1.9050
3.1750
4.4450
5.7150
6.9850
4
PACKAGE TOP VIEW
3.1750
3.1750
SUGGESTED PCB LAYOUT
TOP VIEW
1.9050
PAD 1
CORNER
D
0.6350
0.0000
0.6350
aaa Z
1.9050
X
E
Y
bbb Z
0.36
3.95
MIN
4.31
0.60
H1
SUBSTRATE
NOM
4.41
0.63
15.00
15.00
1.27
13.97
13.97
0.41
4.00
DIMENSIONS
eee S X Y
Z
0.46
4.05
0.15
0.10
0.05
MAX
4.51
0.66
NOTES
DETAIL B
TOTAL NUMBER OF LGA PADS: 144
SYMBOL
A
b
D
E
e
F
G
H1
H2
aaa
bbb
eee
DETAIL A
0.630 ±0.025 SQ. 143x
aaa Z
DETAIL B
H2
MOLD
CAP
A
(Reference LTC DWG # 05-08-1844 Rev C)
LGA Package
144-Lead (15mm × 15mm × 4.41mm)
e
3
PADS
SEE NOTES
F
b
11
10
9
7
6
5
PACKAGE BOTTOM VIEW
8
G
4
b
3
2
1
DETAIL A
A
B
C
D
E
F
G
H
J
K
L
M
DETAILS OF PAD #1 IDENTIFIER ARE OPTIONAL,
BUT MUST BE LOCATED WITHIN THE ZONE INDICATED.
THE PAD #1 IDENTIFIER MAY BE EITHER A MOLD OR
MARKED FEATURE
4
TRAY PIN 1
BEVEL
COMPONENT
PIN “A1”
7
!
6.9850
5.7150
4.4450
4.4450
5.7150
6.9850
PACKAGE IN TRAY LOADING ORIENTATION
LTMXXXXXX
µModule
LGA 144 1112 REV C
7
SEE NOTES
DIA 0.630
PAD 1
PACKAGE ROW AND COLUMN LABELING MAY VARY
AMONG µModule PRODUCTS. REVIEW EACH PACKAGE
LAYOUT CAREFULLY
6. THE TOTAL NUMBER OF PADS: 144
5. PRIMARY DATUM -Z- IS SEATING PLANE
LAND DESIGNATION PER JESD MO-222, SPP-010
3
2. ALL DIMENSIONS ARE IN MILLIMETERS
NOTES:
1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M-1994
12
e
3x, C (0.22 x45°)
LTM4620
PACKAGE DESCRIPTION
Please refer to http://www.linear.com/product/LTM4620#packaging for the most recent package drawings.
4620fc
37
0.630 ±0.025 Ø 144x
4
PACKAGE TOP VIEW
3.1750
3.1750
SUGGESTED PCB LAYOUT
TOP VIEW
1.9050
PIN “A1”
CORNER
D
0.6350
0.0000
0.6350
aaa Z
1.9050
X
For more information www.linear.com/LTM4620
6.9850
5.7150
4.4450
3.1750
1.9050
0.6350
0.0000
0.6350
1.9050
3.1750
4.4450
5.7150
6.9850
E
Y
aaa Z
b1
SYMBOL
A
A1
A2
b
b1
D
E
e
F
G
H1
H2
aaa
bbb
ccc
ddd
eee
NOM
5.01
0.60
4.41
0.75
0.63
15.00
15.00
1.27
13.97
13.97
0.41
4.00
MAX
5.21
0.70
4.51
0.90
0.66
DIMENSIONS
BALL DIMENSION
PAD DIMENSION
BALL HT
NOTES
DETAIL B
PACKAGE SIDE VIEW
Z
SUBSTRATE THK
0.46
MOLD CAP HT
4.05
0.15
0.10
0.20
0.30
0.15
TOTAL NUMBER OF BALLS: 144
0.36
3.95
MIN
4.81
0.50
4.31
0.60
0.60
H1
SUBSTRATE
ddd M Z X Y
eee M Z
DETAIL A
Øb (144 PLACES)
DETAIL B
H2
MOLD
CAP
ccc Z
A1
A2
A
(Reference LTC DWG # 05-08-1880 Rev C)
// bbb Z
38
Z
BGA Package
144-Lead (15mm × 15mm × 5.01mm)
e
12
11
10
9
7
6
5
PACKAGE BOTTOM VIEW
8
4
b
3
2
1
DETAIL A
DETAILS OF PIN #1 IDENTIFIER ARE OPTIONAL,
BUT MUST BE LOCATED WITHIN THE ZONE INDICATED.
THE PIN #1 IDENTIFIER MAY BE EITHER A MOLD OR
MARKED FEATURE
4
A
B
C
D
E
F
G
H
J
K
L
M
7
TRAY PIN 1
BEVEL
!
PACKAGE IN TRAY LOADING ORIENTATION
LTMXXXXXX
µModule
7
SEE NOTES
PIN 1
BGA 144 1116 REV C
PACKAGE ROW AND COLUMN LABELING MAY VARY
AMONG µModule PRODUCTS. REVIEW EACH PACKAGE
LAYOUT CAREFULLY
6. SOLDER BALL COMPOSITION CAN BE 96.5% Sn/3.0% Ag/0.5% Cu
OR Sn Pb EUTECTIC
5. PRIMARY DATUM -Z- IS SEATING PLANE
BALL DESIGNATION PER JESD MS-028 AND JEP95
3
2. ALL DIMENSIONS ARE IN MILLIMETERS
NOTES:
1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M-1994
COMPONENT
PIN “A1”
3
SEE NOTES
F
b
e
G
LTM4620
Please refer to http://www.linear.com/product/LTM4620#packaging for the most recent package drawings.
PACKAGE DESCRIPTION
4620fc
6.9850
5.7150
4.4450
4.4450
5.7150
6.9850
LTM4620
REVISION HISTORY
REV
DATE
DESCRIPTION
A
10/13
Revised temperature monitoring (TEMP) explanation
PAGE NUMBER
B
02/14
Added SnPb BGA package option
C
06/17
Added LTM4620Y MP-Grade to the Order Information
Added BGA package
20, 21
2, 38, 40
1, 2
2
4620fc
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representaFor more
information
www.linear.com/LTM4620
tion that the interconnection
of its circuits
as described
herein will not infringe on existing patent rights.
39
LTM4620
PACKAGE PHOTO
LGA
BGA
RELATED PARTS
PART NUMBER
DESCRIPTION
COMMENTS
LTM4628
Dual 8A, Single 16A µModule Regulator
Pin Compatible with LTM4620; 4.5V ≤ VIN ≤ 26.5V, 0.6V ≤ VOUT ≤ 5.5V,
15mm × 15mm × 4.32mm
LTM4611
Ultralow VIN, 15A µModule Regulator
1.5V ≤ VIN ≤ 5.5V, 0.8V ≤ VOUT ≤ 5V, 15mm × 15mm × 4.32mm
LTM4627
15A DC/DC µModule Regulator
4.5V ≤ VIN ≤ 20V; 0.6V ≤ VOUT ≤ 5V
LTM8062/
LTM8062A
32VIN, 2A µModule Battery Charger with Maximum
Peak Power Tracking (MPPT)
Adjustable VBATT Up to 14.4V (18.8V for the LTM8062A), C/10 or Timer
Termination, 9mm × 15mm × 4.32mm LGA Package
LTM8027
60VIN, 4A DC/DC Step-Down µModule Regulator
4.5V ≤ VIN ≤ 60V, 2.5V ≤ VOUT ≤ 24V, 15mm × 15mm × 4.32mm LGA Package
LTM4613
EN55022B Compliant 36VIN, 8A Step-Down
µModule Regulator
5V ≤ VIN ≤ 36V, 3.3V ≤ VOUT ≤ 15V, Synchronizable, Parallelable,
15mm × 15mm × 4.32mm LGA Package
LTM4637
20A µModule Regulator
4.5V ≤ VIN ≤ 20V, 0.6V ≤ VOUT ≤ 5.5V, 15mm × 15mm × 4.32mm
DESIGN RESOURCES
SUBJECT
DESCRIPTION
µModule Design and Manufacturing Resources
Design:
• Selector Guides
• Demo Boards and Gerber Files
• Free Simulation Tools
µModule Regulator Products Search
1. Sort table of products by parameters and download the result as a spread sheet.
Manufacturing:
• Quick Start Guide
• PCB Design, Assembly and Manufacturing Guidelines
• Package and Board Level Reliability
2. Search using the Quick Power Search parametric table.
TechClip Videos
Quick videos detailing how to bench test electrical and thermal performance of µModule products.
Digital Power System Management
Linear Technology’s family of digital power supply management ICs are highly integrated solutions that
offer essential functions, including power supply monitoring, supervision, margining and sequencing,
and feature EEPROM for storing user configurations and fault logging.
40
4620fc
LT 0617 REV C • PRINTED IN USA
For more information www.linear.com/LTM4620
www.linear.com/LTM4620
LINEAR TECHNOLOGY CORPORATION 2012
