MAX14630EZK+T

EVALUATION KIT AVAILABLE MAX14630/MAX14632 USB Charger Adapter Emulators General Description Benefits and Features The MAX14630/MAX14632 are USB adapter emulators with automatic host charger identification circuitry for USB dedicated chargers. S Optimized for Charging Adapters  Flexible Device and Adapter Connection Order  Convenient CB Pin Controls the Charging Mode The devices allow USB wall adapters, travel chargers, and other dedicated chargers to identify themselves as a USB dedicated charger to USB devices, an Apple charger to Apple products, and a Samsung Galaxy dedicated charger port to legacy D+/D- short detection devices that use the D+ pullup of the USB transceiver. S Faster Charging  Apple 2A Charging Capability in Autodetection Mode  Samsung Galaxy Tablet 2A Charging Capability (MAX14630) The devices feature a control input that allows for charger mode selection. The MAX14630 supports both Apple 2A and USB Battery Charger (BC) revision 1.2 specification compliant devices in Autodetection 2A mode and Samsung Galaxy Tablet 2A devices in SS 2A mode. The MAX14632 supports Autodetection 2A mode as well as Autodetection 1A mode for compatibility with most Apple and USB BC compliant devices. The devices are available in a 5-pin (2.9mm x 1.6mm) TSOT package and are specified over the -40NC to +85NC extended temperature range. Applications S Improved Charger Interoperability  Meets New USB BC Revision 1.2 Specification  Backward Compatible with Previous USB BC Revisions  Meets China YD/T1591-2009 Charging Specification S Greater User Flexibility  CB Pin Controls Charger Mode S Save Board Space  2.9mm x 1.6mm, 5-Pin TSOT Package Ordering Information appears at end of data sheet. USB Wall Charger and Travel Adapter USB Car Charger and Cigarette Lighter Adapter Universal Charger including iPod®/iPad®/iPhone® Typical Operating Circuit VCC 0.1µF GND MAX14630 MAX14632 DP D+ DM DC-DC GND CB D- VCC USB A CONNECTOR VBUS 150µF iPod, iPad, and iPhone are registered trademarks of Apple, Inc. For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642, or visit Maxim Integrated’s website at www.maximintegrated.com. 19-6386; Rev 1; 3/13 MAX14630/MAX14632 USB Charger Adapter Emulators ABSOLUTE MAXIMUM RATINGS (All voltages referenced to GND.) VCC, CB, DP, DM.....................................................-0.3V to +6V Continuous Current into Any Terminal............................. Q50mA Continuous Power Dissipation (TA = +70NC) TSOT (derate 4.8mW/NC above +70NC) ...................386.5mW Operating Temperature Range........................... -40NC to +85NC Maximum Junction Temperature......................................+150NC Storage Temperature Range............................. -65NC to +150NC Lead Temperature (soldering, 10s).................................+300NC Soldering Temperature (reflow) ......................................+260NC Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. PACKAGE THERMAL CHARACTERISTICS (Note 1) TSOT Junction-to-Ambient Thermal Resistance (BJA­).........207NC/W Junction-to-Case Thermal Resistance (BJC)................50NC/W Note 1: Package thermal resistances were obtained using the method described in JEDEC specification JESD51-7, using a four-layer board. For detailed information on package thermal considerations, refer to www.maximintegrated.com/thermal-tutorial. ELECTRICAL CHARACTERISTICS (VCC = 3.0V to 5.5V, TA = -40NC to +85NC, unless otherwise noted. Typical values are at VCC = +5.0V, TA = +25NC, unless otherwise noted.) (Note 2) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS 5.5 V POWER SUPPLY Operating Power-Supply Range VCC VCC Supply Current ICC POR POR Delay   Apple divider valid range 3 4.75 5.5 V 42 µA VCC = 5.0V 25   1.5 V 100 ms tPOR   VDP, VDM   ANALOG SWITCH Analog Signal Range On-Resistance of DP/DM Short RSHORT 0 VCB = 0V, VDP = 0.7V, IDM_SINK = 100µA to GND 4.5 VCC V 11 ω DYNAMIC CB Switching Time tON CB = VCC to 0, 0 to VCC RPD   4 µs INTERNAL RESISTORS DP/DM Short Pulldown 40VCC Bias 54VCC Bias 25VCC Bias Maxim Integrated       350 500 700 kω 39 40 41 %VCC 52.6 53.6 54.6 %VCC 24 25 26 %VCC   2 MAX14630/MAX14632 USB Charger Adapter Emulators ELECTRICAL CHARACTERISTICS (continued) (VCC = 3.0V to 5.5V, TA = -40NC to +85NC, unless otherwise noted. Typical values are at VCC = +5.0V, TA = +25NC unless otherwise noted.) (Note 2) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS LOGIC INPUT (CB) CB Input Logic-High CB Input Logic-Low CB Input Leakage Current VIH   1.4 VIL   ICB 0 ≤ VIN ≤ VIL and VIH ≤ VIN ≤ VCC, VCC = 5.5V V -1 0.4 V 1 µA COMPARATOR CHARACTERISTICS (VCC = 4.75V to 5.5V, TA = -40NC to +85NC, unless otherwise noted. Typical values are at VCC = +5.0V, TA = +25NC, unless otherwise noted.) (Notes 2, 3) PARAMETER SYMBOL CONDITIONS DM1 Comparator Threshold VDM1F DM falling DM2 Comparator Threshold VDM2F DM falling DM2 Comparator Hysteresis   DP Comparator Threshold VDPR DP Comparator Hysteresis   MIN TYP MAX MAX14632: CB = 0 40 41 42 MAX14630: CB = 0 MAX14632: CB = 1 31 32 33 6.31 7 7.62 %VCC   1   % MAX14632: CB = 0 45 46 47 MAX14630: CB = 0 MAX14632: CB = 1 57 58 59   1     DP rising   UNITS %VCC %VCC % Note 2: All units are 100% production tested at TA = +25NC. Specifications over operating temperature range are guaranteed by design. Note 3: The comparators are disabled during the POR delay. Maxim Integrated   3 MAX14630/MAX14632 USB Charger Adapter Emulators Typical Operating Characteristics (VCC = 5.0V, TA = +25°C, unless otherwise noted.) IDP = 10mA SUPPLY CURRENT (µA) 6 4 VCC = 3.0V VCC = 5.5V 30 20 TA = +85°C 10 0 3.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 3.5 4.0 4.5 5.0 VCC (V) SUPPLY CURRENT vs. LOGIC LEVEL LOGIC-INPUT THRESHOLD vs. SUPPLY VOLTAGE VCC = 5.5V 50 40 30 20 10 5.5 2.0 1.8 LOGIC-INPUT THRESHOLD (V) MAX14630 toc03 VDP (V) 60 SUPPLY CURRENT (µA) TA = +25°C TA = -40°C 0 70 CB = VCC MAX14630 toc04 ON-RESISTANCE (I) 8 3 40 MAX14630 toc01 10 MAX14630 toc02 SUPPLY CURRENT vs. SUPPLY VOLTAGE DP/DM SHORT ON-RESISTANCE vs. VDP 1.6 1.4 CB RISING 1.2 1.0 0.8 0.6 CB FALLING 0.4 0.2 0 0 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 3.0 VCB 3.5 4.0 4.5 5.0 5.5 SUPPLY VOLTAGE (V) USB-COMPLIANT DEVICE ATTACH EVENT CB LOGIC-HIGH TO LOGIC-LOW EVENT MAX14630 toc05 MAX14630 toc06 CB DM DP DP DM 1ms/div Maxim Integrated 10µs/div   4 MAX14630/MAX14632 USB Charger Adapter Emulators Pin Description Pin Configuration TOP VIEW + DP 1 GND 2 5 DM MAX14630 MAX14632 CB 3 4 VCC PIN NAME FUNCTION 1 DP 2 GND 3 CB Control Bit 4 VCC Power Supply. Bypass VCC with a 0.1FF ceramic capacitor as close as possible to the pin. 5 DM USB Connector D- Connection USB Connector D+ Connection IC Ground. Return to the transformer output. TSOT Functional Diagram VCC VCC MAX14630 MAX14632 RP1 RP2 DP RM1 DM RM2 500kΩ VDP POR CB DP VDM1 DM1 VDM2 DM2 CONTROL LOGIC GND Maxim Integrated   5 MAX14630/MAX14632 USB Charger Adapter Emulators Detailed Description The MAX14630/MAX14632 are USB adapter emulators with automatic charger identification circuitry for USB dedicated chargers. The devices allow USB wall adapters, travel chargers, and other dedicated chargers to identify themselves as a USB dedicated charger to USB devices, an Apple charger to Apple products, and a Samsung Galaxy dedicated charger port to legacy D+/D- short detection devices that use the D+ pullup of the USB transceiver. Resistor-Dividers The devices feature internal resistor-dividers for biasing data lines to provide support for Apple-compliant devices. Mode Control The devices feature a digital input, CB, for mode selection. For MAX14630, connect CB to a logic-level low voltage for Autodetection 2A charger mode or to a logic-level high voltage for Samsung 2A charger mode. See Table 1. For the MAX14632, connect CB to a logic-level high voltage for Autodetection 2A charger mode. Connect CB to a logic-level low voltage to place the MAX14632 in Autodetection 1A charger mode. See Table 2. Autodetection The MAX14630/MAX14632 feature Autodetection mode for dedicated chargers. In Autodetection charger mode, the device monitors the voltages at DM and DP to determine the type of device attached. With the MAX14630 or MAX14632 in Autodetection mode, when the voltage at DM is VDM1 or higher, and the voltage at DP is VDP or lower, the voltage remains unchanged. If the voltage at DM is forced below the VDM1 threshold, the internal switch discon­ nects DM and DP from the resistor-divider, and DM and DP are shorted together for dedicated charging mode. Similarly, if the voltage at DP is forced higher than the VDP threshold, the internal switch disconnects DM and DP from the resistor-divider, and DM and DP are shorted together for dedicated charging mode. Once the charging voltage is removed, the short between DM and DP is disconnected. Table 1. Digital Input State for the MAX14630 CB MODE 0 Autodetection 2A 1 SS 2A STATUS Supports Apple 2A and USB BC compliant devices. Supports Samsung Galaxy Tablet 2A and USB BC compliant devices. Table 2. Digital Input State for the MAX14632 CB MODE 0 Autodetection 1A Supports Apple 1A and USB BC compliant devices. 1 Autodetection 2A Supports Apple 2A and USB BC compliant devices. Maxim Integrated STATUS   6 MAX14630/MAX14632 USB Charger Adapter Emulators Ordering Information TEMP RANGE PIN-PACKAGE TOP MARK CB = 0/1 MAX14630EZK+T PART -40NC to +85NC 5 TSOT ADSM Autodetection 2A/SS 2A MAX14632EZK+T -40NC to +85NC 5 TSOT ADSN Autodetection 1A/ Autodetection 2A +Denotes a lead(Pb)-free/RoHS-compliant package. T = Tape and reel. Chip Information PROCESS: BiCMOS Maxim Integrated Package Information For the latest package outline information and land patterns (footprints), go to www.maximintegrated.com/packages. Note that a “+”, “#”, or “-” in the package code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing pertains to the package regardless of RoHS status. PACKAGE TYPE PACKAGE CODE OUTLINE NO. LAND PATTERN NO. 5 TSOT Z5+1 21-0113 90-0241   7 MAX14630/MAX14632 USB Charger Adapter Emulators Revision History REVISION NUMBER REVISION DATE DESCRIPTION PAGES CHANGED 0 6/12 Initial release — 1 3/13 Removed future product designation from the MAX14632 in the Ordering Information 7 Maxim Integrated cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim Integrated product. No circuit patent licenses are implied. Maxim Integrated reserves the right to change the circuitry and specifications without notice at any time. The parametric values (min and max limits) shown in the Electrical Characteristics table are guaranteed. Other parametric values quoted in this data sheet are provided for guidance. Maxim Integrated 160 Rio Robles, San Jose, CA 95134 USA 1-408-601-1000 ©  2013 Maxim Integrated Products, Inc. 8 Maxim Integrated and the Maxim Integrated logo are trademarks of Maxim Integrated Products, Inc.