MAX16969BGEE/V+CLV

      MAX16969 500mA–3A Automotive Hi-Speed USB Protector with Apple iPod Fast-Charge Detection and USB Host-Charger Port Detection Fully Integrated Automotive-Grade USB Protector with Apple and USB Host Charger Detection   Request Full Data Sheet   Description The MAX16969 provides high-ESD and short-circuit protection for the low-voltage internal USB data and USB power line in automotive radio, navigation, connectivity, and USB hub applications. The device supports both Hi-Speed USB (480Mbps) and full-speed USB (12Mbps) operation. In addition, the device also includes integrated circuitry to enable fast-charging for consumer devices adhering to either the Apple method or the Hi-Speed USB host-charger portdetection protocol. The short-circuit protection features include short-to-battery on the protected HVBUS, HVD+, and HVD- outputs, as well as short-to-HVBUS on the protected HVD+ and HVD- outputs. The device is capable of a short-to-battery condition of up to +18V. Short-to-GND and overcurrent protection are also provided on the HVBUS output to protect the internal BUS power rail from overcurrent faults. The device features high-ESD protection to ±15kV Air Gap method and ±8kV Contact method on all protected HVBUS, HVD+, and HVD- outputs. The device features two low 4.0Ω on-resistance Hi-Speed USB switches, a current-limited lowvoltage 22mΩ BUS switch, and provides an integrated high-voltage external power-switch controller. The BUS switch can start up into large capacitive noncompliant USB loads. The device also features an enable input, a fault output, integrated Apple iPod®/iPhone® fastcharging termination resistors, and an integrated host-charger port-detection circuit adhering to the USB 2.0 battery charging specification.     The device is available in a 16-pin QSOP package, and operates over -40°C to +105°C temperature range. Key Features              Two 4.0Ω (typ) RON USB 2.0 Data Switches Current-Limited 22mΩ (typ) BUS Switch with High-Capacitive Load Capability 480Mbps or 12Mbps USB 2.0 Operation Short-to-Battery and Short-to-GND Protection on Protected HVBUS Output Short-to-Battery and Short-to-HVBUS Protection on Protected HVD+ and HVD- Outputs 20ms Fault-Blanking Timeout Period Integrated Overcurrent and Short-Circuit Autoretry Integrated Apple iPod Fast-Charge Termination Resistors Integrated USB Host-Charger Port-Detection Circuitry High ESD Protection (HVD+, HVD-, HVBUS) o ±15kV Human Body Model o ±15kV IEC 61000-4-2 Air Gap o ±8kV IEC 61000-4-2 Contact 16-Pin (3.90mm x 4.94mm) QSOP Package -40°C to +105°C Operating Temperature Range AEC-Q100 Qualified Applications/Uses   Automotive USB Protection Rapid Charging for Apple-Compliant Devices  Device Fab Process Technology Sample size Rejects FIT at 25°C FIT at 55°C S4 BiCMOS 1492 0 0.14 2.42 MAX16969BGEE/V+CLV*S4 BiCMOS 1492 0 0.14 2.42 MAX16969EVKIT+* S4 BiCMOS 1492 0 0.14 2.42 MAX16969BGEE/V+* S4 BiCMOS 1492 0 0.14 2.42 MAX16969BGEE/V+T* S4 BiCMOS 1492 0 0.14 2.42 MAX16969DGEE/V+T* S4 BiCMOS 1492 0 0.14 2.42 MAX16969DGEE/V+* Note : The failure rates are summarized by technology and mapped to the associated material part numbers. The failure rates are highly dependent on the number of units tested.     Quality Management System > Environmental Management System >   Key Specs  Current Current Current Lowest RON Limit Limit Current (Ω) Part Power Data Fault Limit Adj. (mA) (mA) USB Limit Set Number Switches Switches Indicator Accuracy Setting By (%) (A) MAX16 Yes 1 969 1 min max 500 3000 typ Yes 20 Resistor 0.67 VSUPPLY VSUPPLY Supported Oper. (V) (V) Package/ Charging Temp. Pins Configurations (°C) min 0.022 4.75 max 5.25 -40 to BC1.1 See Data iPod/iPhone +105 Sheet                                                       https://www.maximintegrated.com/en/products/power/protection‐control/protection‐ics/MAX16969.html 11‐19‐18