19-1712; Rev 1; 2/11
Dual Trip SOT Temperature Switches
The MAX6505–MAX6508 temperature switches have dual
logic outputs that assert when the die temperature crosses their trip thresholds. Trip thresholds are factory programmed to convenient temperatures in 5°C increments.
The MAX6505/MAX6506 have an ALARM output that
asserts when the temperature is above the factory-programmed thresholds (available from -40°C to +125°C).
They also have a WARN output that asserts when the
temperature is several degrees below the ALARM threshold. The difference between the ALARM and WARN
thresholds (ΔTAW) is pin selectable to +5°C, +10°C,
+20°C, or +30°C. The MAX6505’s logic outputs are open
drain, while the MAX6506’s logic outputs are push-pull.
The MAX6507 has open-drain outputs (OVER, OK), and
the MAX6508 has push-pull outputs (OVER, OK), each
with two factory-programmed threshold temperatures
(T OVER and T UNDER ) in the wide range of -40°C to
+125°C. The overtemperature output asserts when the
temperature is above TOVER. When the temperature is in
the desired window (less than TOVER and greater than
TUNDER), OK (OK) asserts.
The MAX6505–MAX6508 are accurate to ±0.5°C (typ),
±5.5°C (max). Operating from a +2.5V to +5.5V supply,
these low-cost devices typically consume 30µA supply
current and require no external components for setting
trip points. The MAX6505–MAX6508 are available in a
6-pin SOT23 package.
________________________Applications
µP Temperature Monitoring in High-Speed
Computers
Temperature Control
Temperature Alarms
Fan Control
Typical Operating Circuits appear at end of data sheet.
Features
♦ ±0.5°C (typ) Threshold Accuracy Over Full
Temperature Range
♦ No External Components Required
♦ Low Cost
♦ 30µA (typ) Supply Current
♦ Factory-Programmed Thresholds from -40°C to
+125°C in 5°C Increments
♦ Open-Drain Outputs (MAX6505/MAX6507),
Push-Pull Outputs (MAX6506/MAX6508)
♦ Pin Selectable 2°C, 10°C Hysteresis
(MAX6507/MAX6508)
♦ Pin Selectable +5°C, +10°C, +20°C, +30°C
TALARM - TWARN (MAX6505/MAX6506)
♦ SOT23 Package
Ordering Information
PART
TEMP RANGE
PIN-PACKAGE
MAX6505UT_ _ _ _+T
-40°C to +125°C 6 SOT23
MAX6506UT_ _ _ _+T
-40°C to +125°C 6 SOT23
MAX6507UT_ _ _ _+T
-40°C to +125°C 6 SOT23
MAX6508UT_ _ _ _+T
-40°C to +125°C 6 SOT23
Note: To complete the suffix information for the MAX6505/
MAX6506, add P or N for positive or negative trip temperature, and select an available trip point in degrees centigrade.
For example, the MAX6505UTP055+T describes a MAX6505 in
a SOT23 package with a +55°C threshold (Table 3). Contact
the factory for pricing and availability of temperature versions
(minimum order 10,000 pieces).
To complete the suffix information for MAX6507/MAX6508, see
Table 4.
+Denotes a lead(Pb)-free/RoHS-compliant package.
T = Tape and reel.
Selector Guide appears at end of data sheet.
Pin Configurations
TOP VIEW
WARN
(WARN) 1
GND 2
+
MAX6505
MAX6506
S1 3
( ) ARE FOR MAX6506.
SOT23
6
ALARM
(ALARM)
OK
1
(OK)
5
S0
GND 2
4
VCC
+
MAX6507
MAX6508
S0 3
SOT23
6
OVER
(OVER)
5
N.C.
4
VCC
( ) ARE FOR MAX6508.
________________________________________________________________ Maxim Integrated Products
For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642,
or visit Maxim’s website at www.maxim-ic.com.
1
MAX6505–MAX6508
General Description
MAX6505–MAX6508
Dual Trip SOT Temperature Switches
ABSOLUTE MAXIMUM RATINGS
Supply Voltage (VCC to GND) ..................................-0.3V to +6V
S1, S0 to GND ............................................-0.3V to (VCC + 0.3V)
All Other Pins to GND.................................-0.3V to (VCC + 0.3V)
Input/Output Current, All Pins...........................................±20mA
Continuous Power Dissipation (TA = +70°C)
SOT23 (derate 8.7mW/°C above +70°C) ....................696mW
Operating Temperature Range (TMIN to TMAX) ..-40°C to +125°C
Thermal Resistance (θJA)...............................................115°C/W
Storage Temperature Range .............................-65°C to +150°C
Maximum Die Temperature..............................................+150°C
Lead Temperature (soldering, 10s) .................................+300°C
Soldering Temperature (reflow) .......................................+260°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(VCC = +2.5V to +5.5V, RPULLUP = 100kΩ (MAX6505/MAX6507 only), TA = -40°C to +125°C, unless otherwise noted. Typical values
are at TA = +25°C and VCC = +5V, unless otherwise noted.) (Note 1)
PARAMETER
Supply Voltage Range
Supply Current
Temperature Threshold
Accuracy (Note 2)
Delta Temperature
(TALARM -TWARNING)
MAX6505/MAX6506
Temperature Threshold
Hysteresis (Note 3)
SYMBOL
CONDITIONS
VCC
Output Voltage Low
2
V
80
S0 = GND
MAX6507/
MAX6508
30
60
μA
-40°C to 0° C
-5.5
±0.5
5.5
0°C to +95° C
-3.5
±0.5
3.5
-4
±0.5
4
S1 = GND, S0 = GND
5
S1 = GND, S0 = VCC
10
S1 = VCC, S0 = GND
20
S1 = VCC, S0 = VCC
30
ALARM (MAX6505/MAX6506)
2
WARN
(MAX6505/MAX6506)
THYST
ΔTAW = 5°C or
10°C
5
ΔTAW = 20°C or
30°C
10
S0 = GND
2
S0 = VCC
10
°C
°C
°C
0.8 x
VCC
VIH
V
0.8
ISOURCE = 500μA, VCC > 2.5V
0.8 x
VCC
ISOURCE = 800μA,VCC > 4.5V
VCC
-1.5
VOH
VOL
5.5
40
VIL
Output Voltage High
(MAX6506/MAX6508)
UNITS
MAX6505/
MAX6506
OK, OVER
(MAX6507/MAX6508)
Logic Input Levels (S1, S0)
MAX
S0 = S1 = GND
+95°C to +125 ° C
ΔTAW
TYP
2.5
ICC
ΔTTH
MIN
V
ISINK = 3.2mA, VCC > 2.5V
0.5
ISINK = 5mA, VCC > 4.5V
0.5
_______________________________________________________________________________________
V
Dual Trip SOT Temperature Switches
(VCC = +2.5V to +5.5V, RPULLUP = 100kΩ (MAX6505/MAX6507 only), TA = -40°C to +125°C, unless otherwise noted. Typical values
are at TA = +25°C and VCC = +5V, unless otherwise noted.) (Note 1)
PARAMETER
SYMBOL
CONDITIONS
Open-Drain Output Leakage
Current
Note 1:
Note 2:
Note 3:
MIN
TYP
MAX
VCC = 5.5V, VALARM = 5.5V,
VWARN = 5.5V (MAX6505)
1
VCC = 5.5V, VOK = 5.5V,
VOVER = 5.5V (MAX6507)
1
UNITS
μA
100% production tested at TA = +25°C. Specifications over temperature limits are guaranteed by design.
TALARM, TUNDER, and TOVER are factory-programmed temperature trip thresholds from -40°C to +125°C in 5°C increments.
Temperature threshold hysteresis is defined as the difference from positive-going temperature thresholds minus the negative-going temperature thresholds.
Typical Operating Characteristics
(VCC = +5V, unless otherwise noted.)
SUPPLY CURRENT
vs. TEMPERATURE
30
0
TRIP-POINT ERROR (%)
35
1.5
1.0
MAX6505/8-03
VCC = +5V
RPULLUP = 100kΩ
2.0
40
0.1
MAX6505/8-02
VCC = +5V
RPULLUP = 100kΩ
HYSTERESIS (°C)
-0.1
-0.2
-0.3
-0.4
-0.5
-0.6
25
NORMALIZED TO TRIP-POINT
TEMPERATURE AT VCC = +5V
-0.7
0.5
20
-40 -25 -10 5 20 35 50 65 80 95 110 125
-40 -25 -10 5 20 35 50 65 80 95 110 125
TEMPERATURE (°C)
TEMPERATURE (°C)
-0.8
2.5
3.0
3.5
4.0
4.5
5.0
5.5
SUPPLY VOLTAGE (V)
MAX6505
STARTUP DELAY
(T > TTH)
MAX6505/8-05
MAX6505
STARTUP AND POWER-DOWN
(T < TTH)
MAX6505/8-04
SUPPLY CURRENT (µA)
45
2.5
MAX6505/8-01
50
TRIP-POINT ERROR (%)
vs. SUPPLY VOLTAGE
HYSTERESIS vs. TRIP TEMPERATURE
A
A
2V/div
2V/div
B
B
100µs/div
A: VCC PULSE
B: ALARM VOLTAGE, RPULLUP = 100kΩ
100µs/div
A: VCC PULSE
B: ALARM VOLTAGE, RPULLUP = 100kΩ
_______________________________________________________________________________________
3
MAX6505–MAX6508
ELECTRICAL CHARACTERISTICS (continued)
Dual Trip SOT Temperature Switches
MAX6505–MAX6508
Pin Description
PIN
MAX6505
MAX6506
1
FUNCTION
MAX6508
-—
-—
WARN
Open-Drain Active-Low Warning Output. WARN goes low
when the die temperature exceeds TWARN = TALARM ΔTAW.
Push-Pull Active-High Warning Output. WARN goes high
when the die temperature exceeds TWARN = TALARM ΔTAW.
-—
1
-—
-—
WARN
2
2
2
2
GND
3, 5
3, 5
-—
-—
S1, S0
-—
-—
3
3
S0
4
4
4
4
VCC
Supply Voltage Input. Bypass VCC to GND with a 0.1μF
ceramic capacitor.
-—
-—
5
5
N.C.
No Connection. Not internally connected.
-—
-—
6
-—
OVER
-—
-—
_
6
OVER
-—
4
NAME
MAX6507
-—
1
-—
Ground
Delta Temperature Select Input. Connect to VCC or GND to
select the difference between TALARM and TWARN (Table
1 or see Electrical Characteristics).
Hysteresis Select Input. Connect to VCC for 10°C
hysteresis. Connect to GND for 2°C hysteresis.
Open-Drain Active-Low Overtemperature Output. OVER
goes low when the die temperature exceeds the factoryset value of TOVER.
Push-Pull Active-High Overtemperature Output. OVER
goes high when the die temperature exceeds the factoryset value of TOVER.
OK
Open-Drain Active-High Temperature Sensor Output. OK
goes high impedance when the die temperature is
between the factory-set values of TOVER and TUNDER.
When the die temperature is above TOVER or below
TUNDER, OK goes low.
OK
Push-Pull Active-Low Temperature Sensor Output. OK
goes low when the die temperature is between the factoryset values of TOVER and TUNDER. When the die temperature is above TOVER or below TUNDER, OK goes high.
-—
-—
-—
6
-—
-—
-—
ALARM
Open-Drain Active-Low Alarm Output. ALARM goes low
when the die temperature exceeds the factory-set value of
TALARM.
-—
6
-—
-—
ALARM
Push-Pull Active-High Alarm Output. ALARM goes high
when the die temperature exceeds the factory-set value of
TALARM.
1
_______________________________________________________________________________________
Dual Trip SOT Temperature Switches
The MAX6505–MAX6508 fully integrated temperature
switches incorporate two temperature-dependent references and a comparator. One reference exhibits a positive temperature coefficient and the other a negative
temperature coefficient. The temperature at which the
two reference voltages are equal determines the temperature trip point. There are two versions, each of
which has two logic outputs.
The MAX6505/MAX6506 have a main trip point (TALARM)
and a lower, “warning” trip point (TWARN). When the die
temperature rises above these trip points, the ALARM
and WARN outputs are asserted (Figure 1). The difference between the two trip points (ΔTAW) is pin selectable to +5°C, +10°C, +20°C, or +30°C by connecting
the two control pins (S0 and S1) high or low (Table 1).
MAX6505 has open-drain active-low outputs; MAX6506
has push-pull active-high outputs.
The MAX6507/MAX6508 have two factory-programmed
threshold temperatures (TOVER and TUNDER) and two
outputs (OK and OVER). One output (OK) asserts
when the temperature is between TOVER and TUNDER.
The other output (OVER) asserts when the temperature
is above TOVER. Table 4 shows the hex codes to determine the part numbers associated with specific values
of TOVER and TUNDER. The first hex code indicates the
lower trip point (TUNDER) and the second indicates the
higher trip point (TOVER). For example, a part with TUNDER = -10°C and TOVER = +75°C will have the part
number MAX6508UTA04B (Table 4 and Figure 2).
MAX6507 has open-drain outputs; MAX6508 has pushpull outputs.
Hysteresis Selection
The temperature threshold hysteresis for the ALARM
output of the MAX6505/MAX6506 is 2°C. The hysteresis
for the WARN output depends on the value of ΔTAW. If
ΔTAW is 5°C or 10°C (set by S0 and S1), WARN hysteresis is 5°C. If ΔTAW is 20°C or 30°C, WARN hysteresis is 10°C. MAX6507 and MAX6508 have pin-selectable
hysteresis of 2°C or 10°C for both OVER and OK outputs (Table 2).
Applications Information
Thermal Considerations
The MAX6505–MAX6508 supply current is typically
30µA. When used to drive high-impedance loads, the
devices dissipate negligible power. Therefore, the die
temperature is essentially the same as the package
temperature. The key to accurate temperature monitoring is good thermal contact between the MAX6505–
MAX6508 package and the device being monitored. In
MAX6505–MAX6508
_______________Detailed Description
Table 1. MAX6505/MAX6506 ΔTAW
Selection Table
CONTROL PINS
DESCRIPTION
TAW =TALARM – TWARN
(°C)
S1
S0
GND
GND
5
GND
VCC
10
VCC
GND
20
VCC
VCC
30
HYSTERESIS ≈ 2°C
65°C
55°C
HYSTERESIS ≈ 5°C
WARN
ALARM
Figure 1. Temperature Response—MAX6505UTP065 Outputs,
ΔTAW = 10°C, and WARN Hysteresis ≈ 5°C
some applications, the SOT23 packages may be small
enough to fit underneath a socketed microprocessor
(µP), allowing the device to monitor the µP’s temperature directly. Use the monitor’s output to reset the µP,
assert an interrupt, or trigger an external alarm.
Accurate temperature monitoring depends on the thermal resistance between the device being monitored
and the MAX6505–MAX6508 die.
The rise in die temperature due to self-heating is given
by the following formula:
ΔTJ = PDISSIPATION ✕ θJA
where P DISSIPATION is the power dissipated by the
MAX6505–MAX6508, and θJA is the package’s thermal
resistance. The typical thermal resistance is 115°C/W for
the SOT23 package. To limit the effects of self-heating,
minimize the output currents. For example, if the
MAX6505 sinks 5mA, the output voltage is guaranteed to
be less than 0.5V. Therefore, an additional 2.5mW of
_______________________________________________________________________________________
5
MAX6505–MAX6508
Dual Trip SOT Temperature Switches
Table 2. Hysteresis Selection
PART
MAX6505
MAX6506
MAX6507
MAX6508
+75°C
TEMPERATURE
-10°C
TYPICAL THRESHOLD HYSTERESIS
WARN
CONDITIONS
ALARM
CONDITIONS
2°C
—
5°C
—
—
10°C
-—
—
-—
—
—
ΔTWA = 5°C or 10°C
ΔTWA = 20°C or 30°C
—
2°C
S0 = GND
—
—
10°C
S0 = VCC
—
+2.5V TO +5.5V
HYSTERESIS ≈ 2°C
-10°C
HYSFERESIS ≈ 2°C
VCC
*
S1
S0
OVER
OK, OVER
ALARM
MAX6506
WARN
SYSTEM
SHUTDOWN
FAN CONTROL
GND
OK
*ΔTAW = TALARM - TWARN IS SET TO +30°C.
Figure 2. Temperature Response—MAX6507A04B Outputs
with 2°C Hysteresis
Figure 3. Low-Power, High-Reliability, Fail-Safe Temperature
Monitor
power is dissipated within the IC. This corresponds to a
+0.288°C shift in the die temperature in the SOT23.
The high-level integration, low cost, and small size of the
MAX6505–MAX6508 facilitate the use of multiple temperature monitors to increase system reliability.
Power Supply and Bypassing
The MAX6505 and MAX6508 operate from a singlesupply voltage in the +2.5V to +5.5V range. Connect a
0.1µF capacitor on the supply voltage line close to the
VCC pin for bypassing.
Low-Cost, Fail-Safe Temperature Monitor
The MAX6505/MAX6506 provide two outputs that can be
used for fail-safe temperature applications (Figure 3). For
example, the first output can activate a fan when the die
temperature exceeds a certain preset temperature. The
second output asserts at a higher temperature that could
be caused by a wide variety of destructive fault conditions, including latchup, short circuit, and cooling system
failure. This output can be used to initiate such actions
as shutdown of the entire system (see Typical Operating
Circuits).
6
_______________________________________________________________________________________
Dual Trip SOT Temperature Switches
PART
SUFFIX
TRIP POINT
(°C)
TOP MARK
MAX6505
UTN035
-35
MAX6505
UTN030
-30
MAX6505
UTN025
MAX6505
UTN020
MAX6505
TRIP POINT
(°C)
TOP MARK
UTN035
-35
AALR
UTN030
-30
AALS
PART
SUFFIX
AAKK
MAX6506
AAKL
MAX6506
-25
AAKM
MAX6506
UTN025
-25
AALT
-20
AAKN
MAX6506
UTN020
-20
AALU
UTN015
-15
AAKO
MAX6506
UTN015
-15
AALV
MAX6505
UTN010
-10
AAKP
MAX6506
UTN010
-10
AALW
MAX6505
UTN005
-5
AAKQ
MAX6506
UTN005
-5
AALX
MAX6505
UTP000
0
AAKR
MAX6506
UTP000
0
AALY
MAX6505
UTP005
5
AAKS
MAX6506
UTP005
5
AALZ
MAX6505
UTP010
10
AAKT
MAX6506
UTP010
10
AAMA
MAX6505
UTP015
15
AAKU
MAX6506
UTP015
15
AAMB
MAX6505
UTP020
20
AAKV
MAX6506
UTP020
20
AAMC
MAX6505
UTP025
25
AAKW
MAX6506
UTP025
25
AAMD
MAX6505
UTP030
30
AAKX
MAX6506
UTP030
30
AAME
MAX6505
UTP035
35
AAKY
MAX6506
UTP035
35
AAMF
MAX6505
UTP040
40
AAKZ
MAX6506
UTP040
40
AAMG
MAX6505
UTP045
45
AALA
MAX6506
UTP045
45
AAMH
MAX6505
UTP050
50
AALB
MAX6506
UTP050
50
AAMI
MAX6505
UTP055
55
AALC
MAX6506
UTP055
55
AAMJ
MAX6505
UTP060
60
AALD
MAX6506
UTP060
60
AAMK
MAX6505
UTP065
65
AALE
MAX6506
UTP065
65
AAML
MAX6505
UTP070
70
AALF
MAX6506
UTP070
70
AAMM
MAX6505
UTP075
75
AALG
MAX6506
UTP075
75
AAMN
MAX6505
UTP080
80
AALH
MAX6506
UTP080
80
AAMO
MAX6505
UTP085
85
AALI
MAX6506
UTP085
85
AAMP
MAX6505
UTP090
90
AALJ
MAX6506
UTP090
90
AAMQ
MAX6505
UTP095
95
AALK
MAX6506
UTP095
95
AAMR
MAX6505
UTP100
100
AALL
MAX6506
UTP100
100
AAMS
MAX6505
UTP105
105
AALM
MAX6506
UTP105
105
AAMT
MAX6505
UTP110
110
AALN
MAX6506
UTP110
110
AAMU
MAX6505
UTP115
115
AALO
MAX6506
UTP115
115
AAMV
MAX6505
UTP120
120
AALP
MAX6506
UTP120
120
AAMW
MAX6505
UTP125
125
AALQ
MAX6506
UTP125
125
AAMX
_______________________________________________________________________________________
7
MAX6505–MAX6508
Table 3. MAX6505/MAX6506 Suffix and Top Mark Codes
MAX6505–MAX6508
Dual Trip SOT Temperature Switches
Table 4. MAX6507/MAX6508 Trip
Temperature Code
TRIP TEMPERATURE (°C)
-40
-35
-30
-25
-20
-15
-10
-5
0
5
10
15
20
25
30
35
40
45
50
55
60
65
70
75
80
85
90
95
100
105
110
115
120
HEX CODE*
82
87
8C
91
96
9B
A0
A5
00
05
0A
0F
14
19
1E
23
28
2D
32
37
3C
41
46
4B
50
55
5A
5F
64
69
6E
73
78
125
7D
*Two hex codes are used in the suffix. The first indicates the
the low trip temperature and the second indicates the high trip
temperature. For example, the MAX6507UT8255+T has a lower
trip point of -40 °C and an upper trip point of +85 °C.
8
Temperature-Window Alarm
The MAX6507 and MAX6508 have an output (OK, OK)
that indicates the die temperature is within the selected
temperature window. This output is asserted when
within the window, and deasserted when outside the
window. Additionally, a second digital output indicates
when the die temperature is above the upper set point.
This is useful in systems where operation is optimized
over a predetermined temperature range. The thermal
overrange signal can be used to assert a thermal shutdown, power-up, recalibration, or other temperaturedependent function (Figure 4 and Typical Operating
Circuits).
+2.5V TO +5.5V
VCC
S0
OK
MAX6508
OVER
OUT OF RANGE
SHUTDOWN
GND
Figure 4. Temperature-Window Alarms
Chip Information
PROCESS: BiCMOS
Package Information
For the latest package outline information and land patterns
(footprints), go to www.maxim-ic.com/packages. Note that a
“+”, “#”, or “-” in the package code indicates RoHS status only.
Package drawings may show a different suffix character, but
the drawing pertains to the package regardless of RoHS status.
PACKAGE
TYPE
PACKAGE
CODE
OUTLINE
NO.
LAND
PATTERN NO.
6 SOT23
U6SN+1
21-0058
90-0175
_______________________________________________________________________________________
Dual Trip SOT Temperature Switches
VCC
+2.5V TO +5.5V
FAN
+2.5V TO +5.5V
R1
VCC
S0
WARN
MAX6505
S1
R2
VCC
VCC
INT
S0
μP
S1
SHDN
ALARM
GND
GND
WARN
MAX6506
ALARM
GND
VCC
INT
VCC
μP
GND
FAN
+2.5V TO +5.5V
VCC
OVER
VCC
S0
MAX6508
INT
OK
GND
μP
GND
Selector Guide
TEMPERATURE THRESHOLD
RANGE
PART
OUTPUT LOGIC
OUTPUT STAGE
MAX6505
ALARM, WARN
Open Drain
-40°C to +125°C
MAX6506
ALARM, WARN
Push-Pull
-40°C to +125°C
MAX6507
OVER, OK
Open Drain
-40°C to +125°C
MAX6508
OVER, OK
Push-Pull
-40°C to +125°C
_______________________________________________________________________________________
9
MAX6505–MAX6508
Typical Operating Circuits
MAX6505–MAX6508
Dual Trip SOT Temperature Switches
Revision History
REVISION
NUMBER
REVISION
DATE
0
4/00
Initial release
2/11
Changed all leaded parts to lead(Pb)-free parts in the Ordering Information table; in
the Absolute Maximum Ratings section changed the continuous power dissipation
numbers (7.1mW/°C to 8.7mW/°C and 571mW to 696mW) and added the soldering
temperature; added the Package Information table
1
DESCRIPTION
PAGES
CHANGED
—
1, 2, 8
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
10 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600
© 2011 Maxim Integrated Products
Maxim is a registered trademark of Maxim Integrated Products, Inc.
工商网监
湘ICP备2023018690号
