0
登录后你可以
  • 下载海量资料
  • 学习在线课程
  • 观看技术视频
  • 写文章/发帖/加入社区
创作中心
发布
  • 发文章

  • 发资料

  • 发帖

  • 提问

  • 发视频

创作活动
MAX6870ETJ+G05

MAX6870ETJ+G05

  • 厂商:

    AD(亚德诺)

  • 封装:

  • 描述:

    IC SUPERVISOR

  • 数据手册
  • 价格&库存
MAX6870ETJ+G05 数据手册
19-3384; Rev 1; 9/04 KIT ATION EVALU LE B A IL A AV EEPROM-Programmable Hex/Quad Power-Supply Sequencers/Supervisors with ADC The MAX6870/MAX6871 EEPROM-configurable, multivoltage supply sequencers/supervisors monitor several voltage detector inputs, two auxiliary inputs, and four general-purpose logic inputs. The MAX6870/MAX6871 feature programmable outputs for highly configurable power-supply sequencing applications. The MAX6870 features six voltage detector inputs and eight programmable outputs, while the MAX6871 features four voltage detector inputs and five programmable outputs. Manual reset and margin disable inputs offer additional flexibility. All voltage detectors offer two configurable thresholds for undervoltage/overvoltage or dual undervoltage detection. One high voltage input (IN1) provides detector threshold voltages from +2.5V to +13.2V in 50mV increments, or from +1.25V to +7.625V in 25mV increments. A bipolar input (IN2) provides detector threshold voltages from ±2.5V to ±15.25V in 50mV increments, or from ±1.25V to ±7.625V in 25mV increments. Positive inputs (IN3–IN6) provide detector threshold voltages from +1V to +5.5V in 20mV increments, or from +0.5V to +3.05V in 10mV increments. Programmable output stages control power-supply sequencing or system resets/interrupts. Programmable output options include: active-high, active-low, opendrain, weak pullup, push-pull, and charge pump. Programmable timing delay blocks configure each output to wait between 25µs and 1600ms before deasserting. A fault register logs the condition that caused each output to assert (undervoltage, overvoltage, manual reset, etc.). An internal 10-bit ADC monitors the voltage detector inputs, and two auxiliary inputs through a multiplexer that automatically sequences through all inputs every 200ms. A SMBusTM-/I2CT-compatible, serial data interface programs and communicates with the configuration EEPROM, the configuration registers, the internal 4kb user EEPROM, the ADC registers, and the fault registers of the MAX6870/MAX6871. The MAX6870/MAX6871 are available in a 7mm x 7mm x 0.8mm 32-pin thin QFN package and operate over the extended -40°C to +85°C temperature range. Features ♦ Six (MAX6870) or Four (MAX6871) Configurable Input Voltage Detectors One High Voltage Input (+1.25V to +7.625V or +2.5V to +13.2V Thresholds) One Bipolar Voltage Input (±1.25V to ±7.625V or ±2.5V to ±15.25V Thresholds) Four (MAX6870) or Two (MAX6871) Positive Voltage Inputs (+0.5V to +3.05V or +1V to +5.5V Thresholds) ♦ Four General-Purpose Logic Inputs ♦ Two Configurable Watchdog Timers ♦ Eight (MAX6870) or Five (MAX6871) Programmable Outputs Active-High, Active-Low, Open-Drain, Weak Pullup, Push-Pull, Charge-Pump Timing Delays from 25µs to 1600ms ♦ 10-Bit Internal ADC Monitors the Input Voltage Detectors and Two Auxiliary Inputs ♦ Margining Disable and Manual Reset Controls ♦ Internal 1.25V Reference or External Reference Input ♦ 4kb Internal User EEPROM Endurance: 100,000 Erase/Write Cycles Data Retention: 10 Years ♦ I2C/SMBus-Compatible Serial Configuration/Communication Interface ♦ ±1% Threshold Accuracy Ordering Information PART TEMP RANGE PINPACKAGE PKG CODE MAX6870ETJ -40°C to +85°C 32 Thin QFN T3277-2 MAX6871ETJ -40°C to +85°C 32 Thin QFN T3277-2 Applications Telecommunications/Central Office Systems Networking Systems Servers/Workstations Basestations Storage Equipment Multimicroprocessor/Voltage Systems SMBus is a trademark of Intel Corp. Pin Configurations, Typical Operating Circuit, and Selector Guide appear at end of data sheet. ________________________________________________________________ Maxim Integrated Products For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at 1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com. 1 MAX6870/MAX6871 General Description MAX6870/MAX6871 EEPROM-Programmable Hex/Quad Power-Supply Sequencers/Supervisors with ADC ABSOLUTE MAXIMUM RATINGS All Voltages referenced to GND IN3–IN6, ABP, SDA, SCL, A0, A1, GPI1–GPI4, MR, MARGIN, PO5–PO8 (MAX6870), PO3/PO4/PO5 (MAX6871)............-0.3V to +6V IN1, PO1–PO4 (MAX6870), PO1/PO2 (MAX6871)....-0.3V to +14V IN2 ...........................................................................-20V to +20V DBP, AUXIN1, AUXIN2, REFIN.................................-0.3V to +3V Input/Output Current (all pins)..........................................±20mA Continuous Power Dissipation (TA = +70°C) 32-Pin 7mm x 7mm Thin QFN (derate 33.3mW/°C above +70°C) .............................2667mW Operating Temperature Range ...........................-40°C to +85°C Maximum Junction Temperature .....................................+150°C Storage Temperature Range .............................-65°C to +150°C Lead Temperature (soldering, 10s) .................................+300°C Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ELECTRICAL CHARACTERISTICS (VIN1 = +6.5V to +13.2V, VIN2 = +10V, VIN3 to VIN6 = +2.7V to +5.5V, AUXIN_ = GPI_ = GND, MARGIN = MR = DBP, TA = -40°C to +85°C, unless otherwise noted. Typical values are at TA = +25°C.) (Notes 1 and 2) PARAMETER Operating Voltage Range (Note 3) SYMBOL CONDITIONS MIN TYP MAX VIN1 Voltage on IN1 to ensure the device is fully operational, IN3 to IN6 = GND 4.0 13.2 VIN3 to VIN6 Voltage on any one of IN3 to IN6 to ensure the device is fully operational, IN1 = GND 2.7 5.5 UNITS V IN1 Supply Voltage (Note 3) VIN1P Minimum voltage on IN1 to guarantee that the device is powered through IN1 6.5 V Undervoltage Lockout VUVLO Minimum voltage on one of IN3 to IN6 to guarantee the device is EEPROM configured. 2.5 V Supply Current Threshold Range ICC VTH Threshold Accuracy VIN1 = +13.2V, IN2 to IN6 = GND, no load 1.2 1.5 Writing to configuration registers or EEPROM, no load 1.3 2 VIN1 (50mV increments) 2.5 13.2 VIN1 (25mV increments) 1.250 7.625 VIN2 (50mV increments) ±2.50 ±15.25 VIN2 (25mV increments) ±1.250 ±7.625 VIN3 to VIN6 (20mV increments) 1.0 5.5 VIN3 to VIN6 (10mV increments) 0.50 3.05 IN1 to IN6 positive, VIN_ falling TA = +25°C -1.0 +1.0 TA = -40°C to +85°C -1.5 +1.5 -15.25V ≤ VIN2 ≤ -5V, VIN2 falling TA = +25°C -1.5 +1.5 TA = -40°C to +85°C -2 +2 -5V ≤ VIN2 ≤ 0, VIN2 falling TA = +25°C -75 +75 TA = -40°C to +85°C -100 +100 mA V % mV Threshold Hysteresis VTH-HYST 0.3 % VTH Reset Threshold Temperature Coefficient ∆VTH/°C 10 ppm/ °C Threshold-Voltage Differential Nonlinearity VTH DNL 2 -1 _______________________________________________________________________________________ +1 LSB EEPROM-Programmable Hex/Quad Power-Supply Sequencers/Supervisors with ADC (VIN1 = +6.5V to +13.2V, VIN2 = +10V, VIN3 to VIN6 = +2.7V to +5.5V, AUXIN_ = GPI_ = GND, MARGIN = MR = DBP, TA = -40°C to +85°C, unless otherwise noted. Typical values are at TA = +25°C.) (Notes 1 and 2) PARAMETER SYMBOL IN1 Input Leakage Current ILIN1 IN2 Input Impedance RIN2 IN3 to IN6 Input Impedance RIN3 to RIN6 Power-Up Delay tPU IN_ to PO_ Delay tDPO CONDITIONS MIN For VIN1 < the highest of VIN3 to VIN6 VIN1 > 6.5V tRP PO1–PO4 (MAX6870), PO1/PO2 (MAX6871) Output Low (Note 3) VOL PO5–PO8 (MAX6870), PO3/PO4/ PO5 (MAX6871) Output Low (Note 3) VOL PO1–PO8 Output Initial Pulldown Current IPD UNITS 100 140 µA 230 320 kΩ 70 100 145 kΩ 3.5 ms VABP ≥ VUVLO VIN_ falling or rising, 100mV overdrive Register contents (Table 25) MAX 160 25 000 PO_ Timeout Period TYP µs 25 µs 001 1.406 1.5625 1.719 010 5.625 6.25 6.875 011 22.5 25 27.5 100 45 50 55 101 180 200 220 110 360 400 440 111 1440 1600 1760 VABP ≥ +2.5V, ISINK = 500µA 0.3 VABP ≥ +4.0V, ISINK = 2mA 0.4 VABP ≥ +2.5V, ISINK = 1mA 0.3 VABP ≥ +4.0V, ISINK = 4mA 0.4 VABP ≤ VUVLO, VPO_ = 0.8V 10 ms V V 40 µA +1 µA PO1–PO8 Output Open-Drain Leakage Current ILKG Output high impedance -1 PO1–PO8 Output Pullup Resistance, Weak Pullup Selected RPU VPO_ = 2V 6.6 10 15.0 kΩ PO1–PO4 (MAX6870), PO1/PO2 (MAX6871) Turn-On Time, Charge Pump Selected (Note 4) tON CPO_ = 1500pF, VABP = +3.3V, VPO_ = +7.8V 0.5 1.5 3.0 ms PO1–PO4 (MAX6870), PO1/PO2 (MAX6871) Turn-Off Time, Charge Pump Selected tOFF CPO_ = 1500pF, VABP = +3.3V, VPO_ = +0.5V 30 With respect to VABP, IPO_ < 100nA 5.5 PO1–PO4 (MAX6870), PO1/PO2 (MAX6871) Output High, Charge Pump Selected (Notes 3, 4) PO5–PO8 (MAX6870), PO3/PO4/ PO5 (MAX6871) Output High, Push-Pull Selected (Note 3) µs V VOHCP VOH With respect to VABP, IPO_ < 1µA 4.0 Any one of VIN3 to VIN6 ≥ +2.7V, ISOURCE = 10mA, output pulled up to the same IN_ 1.5 Any one of VIN3 to VIN6 ≥ +2.7V, ISOURCE = 1mA, output pulled up to the same IN_ 0.8 x VIN_ Any one of VIN3 to VIN6 ≥ +4.5V, ISOURCE = 2mA, output pulled up to the same IN_ 0.8 x VIN_ 5.0 6.0 V _______________________________________________________________________________________ 3 MAX6870/MAX6871 ELECTRICAL CHARACTERISTICS (continued) MAX6870/MAX6871 EEPROM-Programmable Hex/Quad Power-Supply Sequencers/Supervisors with ADC ELECTRICAL CHARACTERISTICS (continued) (VIN1 = +6.5V to +13.2V, VIN2 = +10V, VIN3 to VIN6 = +2.7V to +5.5V, AUXIN_ = GPI_ = GND, MARGIN = MR = DBP, TA = -40°C to +85°C, unless otherwise noted. Typical values are at TA = +25°C.) (Notes 1 and 2) PARAMETER MR, MARGIN, GPI_ Input Voltage MR Input Pulse Width SYMBOL CONDITIONS MIN MR to VDBP Pullup Current MARGIN to VDBP Pullup Current GPI_ to PO_ Delay VIH 1.4 tMR 1 tDMR IMR IMARGIN 2 15 µA V MARGIN = +1.4V 5 10 15 µA 15 µA 200 5 Watchdog Input Pulse Width tWDI GPI_ configured as a watchdog input 50 Reference Input Resistance RREFIN ADC Range ADC Total Unadjusted Error (Note 5) TUE Register Contents (Table 28) 10 ADC Total Monitoring Cycle Time AUXIN_ Input Leakage Current DNL tC ILAUXIN_ ns ns 000 5.625 6.25 6.875 001 22.5 25 27.5 010 90 100 110 011 360 400 440 100 1.44 1.60 1.76 101 5.76 6.40 7.04 110 23.04 25.60 28.16 111 92.16 102.40 112.64 1.225 1.25 1.275 VREFIN = +1.25V 500 0 13.2 IN1, LSB = 9.16mV 0 9.366 IN2, LSB = 18.3mV 0 ±15.25 IN2, LSB = 9.16mV 0 ±9.366 IN3 to IN6, LSB = 7.32mV 0 5.50 IN3 to IN6, LSB = 3.66mV 0 3.746 AUXIN_, LSB = 1.2mV 0 1.249 Internal Reference IN1 to IN6 positive s V V ±1.0 IN2 negative ±1.0 %FSR ±1.0 (Note 7) ±1 Monitors all 8 inputs 200 VAUXIN_ = 1.25V ms kΩ IN1, LSB = 18.3mV External Reference, IN1 to IN6 positive (Note 6) ADC Differential Nonlinearity µs 10 VGPI_ = +0.8V VREFIN ns 5 IGPI_ Reference Input Voltage Range V V MR = +1.4V tDGPI_ tWD UNITS µs 100 GPI_ Pulldown Current Watchdog Timeout Period MAX 0.8 MR Glitch Rejection MR to PO_ Delay TYP VIL -1 LSB 266 ms +1 µA SERIAL INTERFACE LOGIC (SDA, SCL, A0, A1) Logic Input Low Voltage VIL Logic Input High Voltage VIH Input Leakage Current ILKG Output Voltage Low VOL Input/Output Capacitance CI/O 4 0.8 2.0 V V -1 +1 ISINK = 3mA 0.4 10 _______________________________________________________________________________________ µA V pF EEPROM-Programmable Hex/Quad Power-Supply Sequencers/Supervisors with ADC (IN1 = GND, VIN2 = +10V, VIN3 to VIN6 = +2.7V to +5.5V, AUXIN_ = GPI_ = GND, MARGIN = MR = DBP, TA = -40°C to +85°C, unless otherwise noted. Typical values are at TA = +25°C.) (Notes 1 and 2) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS 400 kHz TIMING CHARACTERISTICS (Figure 2) Serial Clock Frequency fSCL Clock Low Period tLOW 1.3 µs Clock High Period tHIGH 0.6 µs Bus-Free Time tBUF 1.3 µs START Setup Time tSU:STA 0.6 µs START Hold Time tHD:STA 0.6 µs STOP Setup Time tSU:STO 0.6 µs Data-In Setup Time tSU:DAT 100 ns Data-In Hold Time tHD:DAT 0 900 ns Receive SCL/SDA Minimum Rise Time tR (Note 8) 20 + 0.1 x CBUS ns Receive SCL/SDA Maximum Rise Time tR (Note 8) 300 ns Receive SCL/SDA Minimum Fall Time tF (Note 8) 20 + 0.1 x CBUS ns Receive SCL/SDA Maximum Fall Time tF (Note 8) 300 ns Transmit SDA Fall Time tF CBUS = 400pF Pulse Width of Spike Suppressed tSP (Note 9) EEPROM Byte Write Cycle Time tWR (Note 10) 20 + 0.1 x CBUS 300 ns 11 ms 50 ns Specifications guaranteed for the stated global conditions. The device also meets the parameters specified when 0 < VIN1 < +6.5V, and at least one of VIN3 through VIN6 is between +2.7V and +5.5V, while the remaining VIN3 through VIN6 are between 0 and +5.5V. Note 2: Device may be supplied from any one of IN_, except IN2. Note 3: The internal supply voltage, measured at ABP, equals the maximum of IN3 to IN6 if VIN1 = 0, or equals +5.4V if VIN1 > +6.5V. For +4V < VIN1 < +6.5V and VIN3 through VIN6 > +2.7V, the input that powers the device cannot be determined. Note 4: 100% production tested at TA = +25°C and TA = +125°C. Specifications at TA = -40°C are guaranteed by design. Note 5: VIN_ > 0.3 x ADC range. Note 6: Does not include the inaccuracy of the external +1.25V voltage reference. Note 7: DNL implicitly guaranteed by design in a sigma-delta converter. Note 8: CBUS = total capacitance of one bus line in pF. Rise and fall times are measured between 0.1 x VBUS and 0.9 x VBUS. Note 9: Input filters on SDA, SCL, A0, and A1 suppress noise spikes < 50ns. Note 10: An additional cycle is required when writing to configuration memory for the first time. Note 1: _______________________________________________________________________________________ 5 MAX6870/MAX6871 TIMING CHARACTERISTICS Typical Operating Characteristics (VIN1 = +6.5V to +13.2V, VIN2 = +10V, VIN3–IN6 = +2.7V to +5.5V, AUXIN_ = GPI_ = GND, MARGIN = MR = DBP, TA = +25°C, unless otherwise noted.) SUPPLY CURRENT vs. SUPPLY VOLTAGE (IN3 TO IN6) TA = -40°C 1.0 1.1 1.0 0.9 0.9 0.8 0.8 6.5 7.5 8.5 9.5 10.5 11.5 12.5 TA = +25°C TA = -40°C 2.5 3.0 3.5 4.0 4.5 5.0 26 24 22 20 18 16 14 12 1.015 1.010 1.005 1.000 0.995 0.990 0.985 60 -15 10 35 60 1.010 IN3 THRESHOLD = 1V, 20mV/STEP RANGE 1.008 1.006 1.002 1.000 0.998 0.996 0.994 85 -40 -15 10 35 TEMPERATURE (°C) 450 400 350 VOL (mV) 300 OPEN-DRAIN, CHARGE PUMP, OR WEAK PULLUP PO1–PO4 (MAX6870) PO1/PO2 (MAX6871) 250 200 150 100 PUSH-PULL PO5–PO8 (MAX6870) PO3/PO4/PO5 (MAX6871) 50 0 1 10 100 IN_ THRESHOLD OVERDRIVE (mV) 1000 85 1.004 OUTPUT VOLTAGE LOW vs. SINK CURRENT PO_ ASSERTION OCCURS ABOVE THIS LINE 60 NORMALIZED IN_ THRESHOLD vs. TEMPERATURE TEMPERATURE (°C) MAX6870/71 toc07 MAXIMUM_ TRANSIENT DURATION (µs) 35 0.990 -40 85 10 0.992 MAXIMUM IN_ TRANSIENT DURATION vs. IN_ THRESHOLD OVERDRIVE 6 -15 TEMPERATURE (°C) 1.020 TEMPERATURE (°C) 130 120 110 100 90 80 70 60 50 40 30 20 10 0 0.97 -40 0.980 10 35 0.98 5.5 MAX6870/71 toc05 100mV OVERDRIVE 10 0.99 NORMALIZED WATCHDOG TIMEOUT PERIOD vs. TEMPERATURE NORMALIZED WATCHDOG TIMEOUT PERIOD MAX6870/71 toc04 30 -15 1.00 SUPPLY VOLTAGE (V) IN_ TO PO_ PROPAGATION DELAY vs. TEMPERATURE -40 1.01 0.96 13.5 SUPPLY VOLTAGE (V) 28 1.02 MAX6870/71 toc06 TA = +25°C TA = +85°C 1.2 NORMALIZED IN_ THRESHOLD 1.1 1.3 1.03 MAX6870/71 toc08 1.2 1.4 NORMALIZED PO_ TIMEOUT PERIOD TA = +85°C 1.3 1.04 MAX6870/71 toc02 SUPPLY CURRENT (mA) 1.4 1.5 SUPPLY CURRENT (mA) MAX6870/71 toc01 1.5 NORMALIZED PO_ TIMEOUT PERIOD vs. TEMPERATURE MAX6870/71 toc03 SUPPLY CURRENT vs. SUPPLY VOLTAGE (IN1) IN_ TO PO_ OUTPUT PROPAGATION DELAY (µs) MAX6870/MAX6871 EEPROM-Programmable Hex/Quad Power-Supply Sequencers/Supervisors with ADC 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 ISINK (mA) _______________________________________________________________________________________ 60 85 EEPROM-Programmable Hex/Quad Power-Supply Sequencers/Supervisors with ADC (VIN1 = +6.5V to +13.2V, VIN2 = +10V, VIN3–IN6 = +2.7V to +5.5V, AUXIN_ = GPI_ = GND, MARGIN = MR = DBP, TA = +25°C, unless otherwise noted.) 5.0 4.5 4.0 VOH (V) WEAK PULLUP TO ABP 3.0 2.5 2.0 1.5 1.0 0.5 0 3.5 3.0 2.5 2.0 1.5 1.0 PO5–PO8 (MAX6870) PO3/PO4/PO5 (MAX6871) 4.0 5 10 15 20 25 30 35 40 45 50 55 60 0 1 1.75 1.70 1.65 1.60 1.55 1.50 60 4 5 85 TEMPERATURE (°C) MAX6870/71 toc13 1.80 1.2 MAXIMUM MR TRANSIENT DURATION (µs) MAX6870/71 toc12 1.85 35 3 MAXIMUM MR TRANSIENT DURATION vs. MR THRESHOLD OVERDRIVE 1.90 10 2 SOURCE CURRENT (µA) MR TO PO_ PROPAGATION DELAY vs. TEMPERATURE MR TO PO_ PROPAGATION DELAY (µs) PO1–PO4 (MAX6870) PO1/PO2 (MAX6871) 4.5 IOUT (mA) IOUT (mA) -15 5.0 3.0 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 -40 MEASURED RELATIVE TO VABP 5.5 3.5 0.5 0 1.1 1.0 0.9 0.8 0.7 0.6 0.5 0.4 0.3 PO_ ASSERTION OCCURS ABOVE THIS LINE 0.2 0.1 0 1 10 1000 100 MR THRESHOLD OVERDRIVE (mV) ADC ACCURACY vs. TEMPERATURE 1.0 MAX6870/71 toc14 0 6.0 MAX6870/71 toc11 PUSH-PULL TO IN3 IN3 = 5V OUTPUT VOLTAGE HIGH vs. SOURCE CURRENT (CHARGE-PUMP OUTPUT) OUTPUT VOLTAGE HIGH (V) 6.0 5.5 MAX6870/71 toc09 4.0 3.5 0.8 TOTAL UNADJUSTED ERROR (%) VOH (V) 6.0 5.5 5.0 4.5 MAX6870/71 toc10 OUTPUT VOLTAGE HIGH vs. SOURCE CURRENT (PUSH-PULL OUTPUT) OUTPUT VOLTAGE HIGH vs. SOURCE CURRENT (WEAK PULLUP OUTPUT) 0.6 0.4 VIN2 = -12V, 50mV/STEP RANGE 0.2 FET (IRF7811W) TURN-ON WITH CHARGE PUMP MAX6870/71 toc15 VIN3 = 5V, 20mV/STEP RANGE VPO1 10V/div 0 -0.2 VSOURCE 2V/div -0.4 -0.6 -0.8 VAUXIN1 = 1V VIN1 = 9V, 25mV/STEP RANGE IDRAIN 5A/div -1.0 -40 -15 10 35 60 85 SEE FIGURE 9 TEMPERATURE (°C) 10 /di _______________________________________________________________________________________ 7 MAX6870/MAX6871 Typical Operating Characteristics (continued) MAX6870/MAX6871 EEPROM-Programmable Hex/Quad Power-Supply Sequencers/Supervisors with ADC Pin Description PIN MAX6870 MAX6871 1 3 2 8 5 NAME FUNCTION PO2 Programmable Output 2. Configurable, active-high, active-low, open-drain, weak pullup, or charge-pump output. PO2 pulls low with a 10µA internal current sink for +1V < VABP < VUVLO. PO2 assumes its programmed conditional output state when ABP exceeds UVLO. PO3 Programmable Output 3. Configurable, active-high, active-low, open-drain, weak pullup (MAX6870), push-pull (MAX6871), or charge-pump (MAX6870) output. PO3 pulls low with a 10µA internal current sink for +1V < VABP < VUVLO. PO3 assumes its programmed conditional output state when ABP exceeds UVLO. 3 6 PO4 Programmable Output 4. Configurable, active-high, active-low, open-drain, weak pullup (MAX6870), push-pull (MAX6871), or charge-pump (MAX6870) output. PO4 pulls low with a 10µA internal current sink for +1V < VABP < VUVLO. PO4 assumes its programmed conditional output state when ABP exceeds UVLO. 4 4 GND Ground 5 7 PO5 Programmable Output 5. Configurable, active-high, active-low, open-drain, weak pullup, or push-pull output. PO5 pulls low with a 10µA internal current sink for +1V < VABP < VUVLO. PO5 assumes its programmed conditional output state when ABP exceeds UVLO. 6 — PO6 Programmable Output 6. Configurable, active-high, active-low, open-drain, weak pullup, or push-pull output. PO6 pulls low with a 10µA internal current sink for +1V < VABP < VUVLO. PO6 assumes its programmed conditional output state when ABP exceeds UVLO. 7 — PO7 Programmable Output 7. Configurable, active-high, active-low, open-drain, weak pullup, or push-pull output. PO7 pulls low with a 10µA internal current sink for +1V < VABP < VUVLO. PO7 assumes its programmed conditional output state when ABP exceeds UVLO. 8 — PO8 Programmable Output 8. Configurable, active-high, active-low, open-drain, weak pullup, or push-pull output. PO8 pulls low with a 10µA internal current sink for +1V < VABP < VUVLO. PO8 assumes its programmed conditional output state when ABP exceeds UVLO. 9, 10 1, 8, 9, 10, 25, 26, 32 N.C. No Connection. Not internally connected. 11 11 MARGIN Margin Input. Configure MARGIN to either assert PO_ into a programmed state or to hold PO_ in its existing state when driving MARGIN low. See Table 8. Leave MARGIN unconnected or connect to DBP if unused. MARGIN overrides MR if both assert at the same time. MARGIN is internally pulled up to DBP through a 10µA current source. 12 12 MR Manual Reset Input. Configure MR to either assert PO_ into a programmed state or to have no effect on PO_ when driving MR low. See Table 7. Leave MR unconnected or connect to DBP if unused. MR is internally pulled up to DBP through a 10µA current source. 13 13 SDA Serial Data Input/Output (Open-Drain). SDA requires an external pullup resistor. 14 14 SCL Serial Clock Input. SCL requires an external pullup resistor. 15 15 A0 Address Input 0. Address inputs allow up to four MAX6870/MAX6871 connections on one common bus. Connect A0 to GND or to the serial interface power supply. 16 16 A1 Address Input 1. Address inputs allow up to four MAX6870/MAX6871 connections on one common bus. Connect A1 to GND or to the serial interface power supply. _______________________________________________________________________________________ EEPROM-Programmable Hex/Quad Power-Supply Sequencers/Supervisors with ADC PIN NAME FUNCTION MAX6870 MAX6871 17 17 GPI4 General-Purpose Logic Input 4. An internal 10µA current source pulls GPI4 to GND. Configure GPI4 to control watchdog timer functions or the programmable outputs. 18 18 GPI3 General-Purpose Logic Input 3. An internal 10µA current source pulls GPI3 to GND. Configure GPI3 to control watchdog timer functions or the programmable outputs. 19 19 GPI2 General-Purpose Logic Input 2. An internal 10µA current source pulls GPI2 to GND. Configure GPI2 to control watchdog timer functions or the programmable outputs. 20 20 GPI1 General-Purpose Logic Input 1. An internal 10µA current source pulls GPI1 to GND. Configure GPI1 to control watchdog timer functions or the programmable outputs. 21 21 ABP Internal Power-Supply Output. Bypass ABP to GND with a 1µF ceramic capacitor. ABP powers the internal circuitry of the MAX6870/MAX6871. ABP supplies the input voltage to the internal charge pumps when the programmable outputs are configured as charge-pump outputs. Do not use ABP to supply power to external circuitry. 22 22 DBP Internal Digital Power-Supply Output. Bypass DBP to GND with a 1µF ceramic capacitor. DBP supplies power to the EEPROM memory and the internal logic circuitry. Do not use DBP to supply power to external circuitry. 23 23 AUXIN2 Auxiliary Input 2. A 10-bit ADC monitors the input voltage at AUXIN2. The high-impedance AUXIN2 input accepts input voltages up to VREFIN. AUXIN2 does not influence EEPROMconfigurable power-supply sequencing or reset detection functions. 24 24 AUXIN1 Auxiliary Input 1. A 10-bit ADC monitors the input voltage at AUXIN1. The high-impedance AUXIN1 input accepts input voltages up to VREFIN. AUXIN1 does not influence EEPROMconfigurable power-supply sequencing or reset detection functions. 25 — IN6 Voltage Input 6. Configure IN6 to detect voltage thresholds between +1V and +5.5V in 20mV increments, or +0.5V to +3.05V in 10mV increments. For improved noise immunity, bypass IN6 to GND with a 0.1µF capacitor installed as close to the device as possible. 26 — IN5 Voltage Input 5. Configure IN5 to detect voltage thresholds between +1V and +5.5V in 20mV increments, or +0.5V to +3.05V in 10mV increments. For improved noise immunity, bypass IN5 to GND with a 0.1µF capacitor installed as close to the device as possible. 27 27 IN4 Voltage Input 4. Configure IN4 to detect voltage thresholds between +1V and +5.5V in 20mV increments, or +0.5V to +3.05V in 10mV increments. For improved noise immunity, bypass IN4 to GND with a 0.1µF capacitor installed as close to the device as possible. 28 28 IN3 Voltage Input 3. Configure IN3 to detect voltage thresholds between +1V and +5.5V in 20mV increments, or +0.5V to +3.05V in 10mV increments. For improved noise immunity, bypass IN3 to GND with a 0.1µF capacitor installed as close to the device as possible. IN2 Bipolar Voltage Input 2. Configure IN2 to detect negative voltage thresholds from -2.5V to -15.25V in 50mV increments or -1.25V to -7.625V in 25mV increments. Alternatively, configure IN2 to detect positive voltage thresholds from +2.5V to +15.25V in 50mV increments or +1.25V to +7.625V in 25mV increments. For improved noise immunity, bypass IN2 to GND with a 0.1µF capacitor installed as close to the device as possible. 29 29 _______________________________________________________________________________________ 9 MAX6870/MAX6871 Pin Description (continued) MAX6870/MAX6871 EEPROM-Programmable Hex/Quad Power-Supply Sequencers/Supervisors with ADC Pin Description (continued) PIN MAX6870 MAX6871 30 30 NAME FUNCTION IN1 High Voltage Input 1. Configure IN1 to detect voltage thresholds from +2.5V to +13.2V in 50mV increments or +1.25V to +7.625V in 25mV increments. For improved noise immunity, bypass IN1 to GND with a 0.1µF capacitor installed as close to the device as possible. Reference Voltage Input. Configure the MAX6870/MAX6871 to use either an internal reference or external reference (see Table 9). When configured for an internal reference, leave REFIN unconnected. When configured for an external reference, connect a +1.225V to +1.275V reference to REFIN. 31 31 REFIN 32 2 PO1 — — EP Programmable Output 1. Configurable active-high, active-low, open-drain, weak pullup, or charge-pump output. PO1 pulls low with a weak 10µA internal current sink for +1V < VABP < VUVLO. PO1 assumes its programmed conditional output state when ABP exceeds UVLO. Exposed Paddle. Exposed paddle is internally connected to GND. Detailed Description The MAX6870/MAX6871 EEPROM-configurable, multivoltage supply sequencers/supervisors monitor several voltage-detector inputs, two auxiliary inputs and four general-purpose logic inputs, and feature programmable outputs for highly-configurable, power-supply sequencing applications. The MAX6870 features six voltage-detector inputs and eight programmable outputs, while the MAX6871 features four voltage-detector inputs and five programmable outputs. Manual reset and margin disable inputs simplify board-level testing during the manufacturing process. The MAX6870/ MAX6871 feature an accurate internal 1.25V reference. For greater accuracy, connect an external +1.25V reference to REFIN. All voltage detectors provide two configurable thresholds for undervoltage/overvoltage or dual undervoltage detection. One high-voltage input (IN1) provides detector threshold voltages from +1.25V to +7.625V in 25mV increments or +2.5V to +13.2V in 50mV increments. A bipolar input (IN2) provides detector threshold voltages from ±1.25V to ±7.625V in 25mV increments, or ±2.5V to ±15.25V in 50mV increments. Positive inputs (IN3–IN6) provide detector threshold voltages from +0.5V to +3.05V in 10mV increments, or +1.0V to +5.5V in 20mV increments. 10 An internal 10-bit ADC monitors the voltage-detector inputs and two auxiliary inputs through a multiplexer that automatically sequences through all inputs every 200ms. The host controller communicates with the MAX6870/MAX6871s’ internal 4kb user EEPROM, configuration EEPROM, configuration registers, ADC registers, and fault registers through an SMBus/I2Ccompatible serial interface (see Figure 1). Programmable output options include active-high, active-low, open-drain, weak pullup, push-pull, and charge pump. Select the charge-pump output feature to drive n-channel FETs for power-supply sequencing (see the Applications Information section). The outputs swing between 0 and (VABP + 5V) when configured for charge-pump operation. Program each output to assert on any voltage-detector input, general-purpose logic input, watchdog timer, manual reset, or other output stages. Programmable timing-delay blocks configure each output to wait between 25µs and 1600ms before deasserting. A fault register logs the conditions that caused each output to assert (undervoltage, overvoltage, manual reset, etc.). The MAX6870/MAX6871 feature two watchdog timers, adding flexibility. Program each watchdog timer to assert one or more programmable outputs. Program each ______________________________________________________________________________________ EEPROM-Programmable Hex/Quad Power-Supply Sequencers/Supervisors with ADC OUTPUT STAGES LOGIC NETWORK FOR PO_ COMPARATORS IN_ derive power from IN1 if VIN1 > +6.5V or from the highest voltage on IN3–IN6 if VIN1 < +2.7V. The power source cannot be determined if +4V < VIN1 < +6.5V and one of VIN3 through VIN6 > +2.7V. The programmable outputs maintain the correct programmed logic state for V ABP > V UVLO . One of IN3 through IN6 must be greater than +2.7V or IN1 must be greater than +4V for device operation. PO_ GPI_, MR, MARGIN ADC MUX WATCHDOG TIMERS GPI_ AUXIN_ ADC SDA, SCL ADC REGISTERS SERIAL INTERFACE REGISTER BANK EEPROM (USER AND CONFIG) CONTROLLER ANALOG BLOCK DIGITAL BLOCK Figure 1. Top Level Block Diagram ______________________________________________________________________________________ 11 MAX6870/MAX6871 watchdog timer to clear on a combination of one GPI_ input and one programmable output, one of the GPI_ inputs only, or one of the programmable outputs only. The initial and normal watchdog timeout periods are independently programmable from 6.25ms to 102.4s. A virtual diode-ORing scheme selects the input that powers the MAX6870/MAX6871. The MAX6870/MAX6871 EEPROM-Programmable Hex/Quad Power-Supply Sequencers/Supervisors with ADC GPI2 GPI3 GPI4 MARGIN MR GPI1 MAX6870/MAX6871 Functional Diagram IN3–IN6 (IN3–IN4) ABP IN_ DETECTOR IN1 VABP + 5V CHARGE PUMP* PO_ OUTPUT MUX *PO1–PO4 ONLY (PO1, PO2) ** PO5–PO8 ONLY (PO3, PO4, PO5) P1** 10kΩ OPENDRAIN MUX PO1 1.25V VREF TIMING BLOCK 1 IN2 IN2 DETECTOR IN3 PROGRAMMABLE ARRAY TIMING BLOCK 2 PO2 OUTPUT PO2 IN3 DETECTOR TIMING BLOCK 3 PO3 OUTPUT PO3 IN4 IN4 DETECTOR TIMING BLOCK 4 PO4 OUTPUT PO4 IN5 (N.C.) IN6 (N.C.) IN5 DETECTOR TIMING BLOCK 5 PO5 OUTPUT PO5 IN6 DETECTOR TIMING BLOCK 6 PO6 OUTPUT TIMING BLOCK 7 PO7 OUTPUT TIMING BLOCK 8 PO8 OUTPUT PO6 (N.C.) PO7 (N.C.) PO8 (N.C.) MAIN OSCILLATOR AUXIN1 AUXIN2 ADC MUX ADC TIMING ADC ADC REGISTERS IN1 IN2 IN3 IN4 IN5 IN6 AUXIN1 AUXIN2 EEPROM CHARGE PUMP CONFIG CONFIG REGISTERS EEPROM USER EEPROM SDA 5.4V LDO SERIAL INTERFACE (VIRTUAL DIODES) A0 A1 MAX6870 MAX6871 2.55V LDO DBP 1µF ABP 1µF REFIN 12 SCL GND ( ) ARE FOR MAX6871 ONLY. ______________________________________________________________________________________ EEPROM-Programmable Hex/Quad Power-Supply Sequencers/Supervisors with ADC The MAX6870/MAX6871 also generate a digital supply voltage (DBP) for the internal logic circuitry and the EEPROM; bypass DBP to GND with a 1µF ceramic capacitor installed as close to the device as possible. The nominal DBP output voltage is +2.55V. Do not use DBP to provide power to external circuitry. ADC The MAX6870/MAX6871 feature an internal 10-bit ADC that monitors the voltage-detector inputs and auxiliary inputs through an internal multiplexer that sequences through all input voltages in 200ms. Registers 50h to 5Fh store the ADC data. Read the ADC data from the MAX6870/MAX6871 with the serial interface. The ADC strictly monitors input voltages and has no effect on power-supply sequencing, reset detection, or the programmable outputs. Inputs The MAX6870/MAX6871 contain multiple logic and voltage-detector inputs. Each voltage-detector input is simultaneously monitored for primary and secondary thresholds. The primary threshold must be an undervoltage threshold. The secondary threshold may be an undervoltage or overvoltage threshold. Table 1 summarizes these various inputs. Table 1. Programmable Features FEATURE DESCRIPTION • • • • • Bipolar Voltage Input • (IN2) • • • Positive Voltage Input • IN3–IN6 (MAX6870) • IN3, IN4 (MAX6871) • • Programmable Outputs • PO1–PO4 (MAX6870), • PO1, PO2 (MAX6871) • • • Programmable Outputs • PO5–PO8 (MAX6870), • PO3, PO4, PO5 • (MAX6871) • • High Voltage Input (IN1) Primary undervoltage threshold Secondary overvoltage or undervoltage threshold +2.5V to +13.2V threshold in 50mV increments +1.25V to +7.625V threshold in 25mV increments Primary undervoltage threshold Secondary overvoltage or undervoltage threshold ±2.5V to ±15.25V threshold in 50mV increments ±1.25V to ±7.625V threshold in 25mV increments Primary undervoltage threshold Secondary overvoltage or undervoltage threshold +1V to +5.5V threshold in 20mV increments +0.5V to +3.05V threshold in 10mV increments Active high or active low Open-drain, weak pullup, or charge-pump output Weak pullup to IN3–IN6 (IN3 or IN4 for MAX6871) or ABP Dependent on MR, MARGIN, IN_, GPI1–GPI4 , WDI1 and WDI2, and/or PO_ Programmable timeout periods of 25µs, 1.5625ms, 6.25ms, 25ms, 50ms, 200ms, 400ms, or 1.6s Active high or active low Open-drain, weak pullup, or push-pull output Weak pullup to IN3–IN6 (IN3 or IN4 for MAX6871) or ABP Push-pull to IN3–IN6 (IN3 or IN4 for MAX6871) Dependent on MR, MARGIN, IN_, GPI1–GPI4 , WDI1 and WDI2 , and/or IN_ Programmable timeout periods of 25µs, 1.5625ms, 6.25ms, 25ms, 50ms, 200ms, 400ms, or 1.6s ______________________________________________________________________________________ 13 MAX6870/MAX6871 Powering the MAX6870/MAX6871 The MAX6870/MAX6871 derive power from the positive voltage-detector inputs: IN1, or IN3–IN6. A virtual diodeORing scheme selects the positive input that supplies power to the device (see the Functional Diagram). IN1 must be at least +4V or one of IN3–IN6 (MAX6870)/ IN3/IN4 (MAX6871) must be at least +2.7V to ensure device operation. An internal LDO regulates IN1 down to +5.4V. The highest input voltage on IN3–IN6 (MAX6870)/ IN3/IN4 (MAX6871) supplies power to the device, unless VIN1 ≥ +6.5V, in which case IN1 supplies power to the device. For +4V < VIN1 < +6.5V and one of VIN3 through VIN6 > +2.7V, the input power source cannot be determined due to the dropout voltage of the LDO. Internal hysteresis ensures that the supply input that initially powered the device continues to power the device when multiple input voltages are within 50mV of each other. ABP powers the analog circuitry; bypass ABP to GND with a 1µF ceramic capacitor installed as close to the device as possible. The internal supply voltage, measured at ABP, equals the maximum of IN3–IN6 (MAX6870)/IN3/IN4 (MAX6871) if VIN1 = 0, or equals +5.4V when VIN1 > +6.5V. Do not use ABP to provide power to external circuitry. MAX6870/MAX6871 EEPROM-Programmable Hex/Quad Power-Supply Sequencers/Supervisors with ADC Table 1. Programmable Features (continued) FEATURE DESCRIPTION General-Purpose Logic • Inputs (GPI1–GPI4) • • Active high or active low logic levels Configure GPI_ as inputs to watchdog timers or programmable output stages • • • • Clear dependent on any combination of one GPI_ input and one programmable output, a GPI_ input only, or a programmable output only Initial watchdog timeout period of 6.25ms, 25ms, 100ms, 400ms, 1.6s, 6.4s, 25.6s, or 102.4s Normal watchdog timeout period of 6.25ms, 25ms, 100ms, 400ms, 1.6s, 6.4s, 25.6s, or 102.4s Watchdog enable/disable Initial watchdog timeout period enable/disable Auxiliary Inputs (AUXIN1, AUXIN2) • Monitored by the internal 10-bit ADC Manual Reset Input (MR) • • • Forces PO_ into the active output state when MR = GND PO_ deassert after MR releases high and the PO_ timeout period expires PO_ cannot be a function of MR only • • Holds PO_ in existing state or asserts PO_ to a programmed output state, independent of changes in monitored inputs or watchdog timers, when MARGIN = GND Overrides MR when both assert at the same time Reference Input (REFIN) • • • • Internal +1.25V reference voltage Goes high-impedance when internal reference selected External reference voltage input from +1.225V to +1.275V Sets ADC voltage range 10-Bit ADC* • • • • Monitors IN_, AUXIN1, and AUXIN2 Completes conversion of all eight inputs in 200ms Reference voltage sets ADC range Read ADC data from SMBus/I2C interface Write Disable • Locks user EEPROM based on PO_ Configuration Lock • Locks configuration EEPROM Watchdog Timers Margining Input (MARGIN) *ADC does not control programmable outputs. Set the primary and secondary threshold voltages for each voltage-detector input with registers 00h–0Bh. Each primary threshold voltage must be an undervoltage threshold. Configure each secondary threshold voltage as an undervoltage or overvoltage threshold (see register 0Ch). Set the threshold range for each voltage detector with register 0Dh. High Voltage Input (IN1) IN1 offers threshold voltages of +2.5V to +13.2V in 50mV increments, or +1.25V to +7.625V in 25mV increments. Use the following equations to set the threshold voltages for IN1: V − 2.5V x = TH for + 2.5V to + 13.2V range 0.05V 14 V − 1.25V x = TH for + 1.25V to + 7.625V range 0.025V where VTH is the desired threshold voltage and x is the decimal code for the desired threshold (Table 2). For the +2.5V to +13.2V range, x must equal 214 or less, otherwise the threshold exceeds the maximum operating voltage of IN1. Bipolar Voltage Input (IN2) IN2 offers negative thresholds from -2.5V to -15.25V in 50mV increments, or from -1.25V to -7.625V in 25mV increments. Alternatively, IN2 offers positive thresholds from +2.5V to +15.25V in 50mV increments, or +1.25V to +7.625V in 25mV increments. Use the following equations to set the threshold voltages for IN2: ______________________________________________________________________________________ EEPROM-Programmable Hex/Quad Power-Supply Sequencers/Supervisors with ADC x= x= ) 0.05V ( − VTH − 1.25V ) 0.025V for − 2.5V to − 15.25V range for − 1.25V to − 7.625V range V − 2.5V x = TH for + 2.5V to + 15.25V range 0.05V V − 1.25V x = TH for + 1.25V to + 7.625V range 0.025V where VTH is the desired threshold voltage and x is the decimal code for the desired threshold (Table 3). IN3–IN6 IN3–IN6 offer positive voltage detectors monitor voltages from +1V to +5.5V in 20mV increments, or +0.5V to +3.05V in 10mV increments. Use the following equations to set the threshold voltages for IN_: V − 1V x = TH for + 1V to + 5.5V range 0.02V V − 0.5V x = TH for + 0.5V to + 3.05V range 0.01V where VTH is the desired threshold voltage and x is the decimal code for the desired threshold (Table 4). For the +1V to +5.5V range, x must equal 225 or less, otherwise the threshold exceeds the maximum operating voltage of IN3–IN6. Table 2. IN1 Threshold Settings REGISTER ADDRESS EEPROM MEMORY ADDRESS BIT RANGE 00h 8000h [7:0] IN1 primary undervoltage detector threshold (V1A) (see equations in the High Voltage Input (IN1) section). 06h 8006h [7:0] IN1 secondary undervoltage/overvoltage detector threshold (V1B) (see equations in the High Voltage Input (IN1) section). 0Ch 800Ch [0] IN1 secondary overvoltage/undervoltage selection. 0 = overvoltage threshold. 1 = undervoltage threshold. 0Dh 800Dh [0] IN1 range selection. 0 = 2.5V to 13.2V range in 50mV increments. 1 = 1.25V to 7.625V range in 25mV increments. DESCRIPTION Table 3. IN2 Threshold Settings REGISTER ADDRESS EEPROM MEMORY ADDRESS BIT RANGE 01h 8001h [7:0] IN2 primary undervoltage detector threshold (V2A) (see equations in the Bipolar Voltage Input (IN2) section). 07h 8007h [7:0] IN2 secondary undervoltage/overvoltage detector threshold (V2B) (see equations in the Bipolar Voltage Input (IN2) section). 0Ch 800Ch [1] 0Dh 800Dh [7:6] DESCRIPTION IN2 secondary overvoltage/undervoltage selection. 0 = overvoltage threshold. 1 = undervoltage threshold. IN2 range selection. 00 = -2.5V to -15.25V range in 50mV increments. 01 = -1.25V to -7.625V range in 25mV increments. 10 = +2.5V to +15.25V range in 50mV increments. 11 = +1.25V to +7.625V range in 25mV increments. ______________________________________________________________________________________ 15 MAX6870/MAX6871 ( − VTH − 2.5V MAX6870/MAX6871 EEPROM-Programmable Hex/Quad Power-Supply Sequencers/Supervisors with ADC Table 4. IN3–IN6 Threshold Settings REGISTER ADDRESS EEPROM MEMORY ADDRESS BIT RANGE 02h 8002h [7:0] 03h 8003h [7:0] IN4 primary undervoltage detector threshold (V4A) (see equations in the IN3–IN6 section). IN3 primary undervoltage detector threshold (V3A) (see equations in the IN3–IN6 section). 04h 8004h [7:0] IN5 (MAX6870 only) primary undervoltage detector threshold (V5A) (see equations in the IN3–IN6 section). 05h 8005h [7:0] IN6 (MAX6870 only) primary undervoltage detector threshold (V6A) (see equations in the IN3–IN6 section). 08h 8008h [7:0] IN3 secondary undervoltage/overvoltage detector threshold (V3B) (see equations in the IN3–IN6 section). 09h 8009h [7:0] IN4 secondary undervoltage/overvoltage detector threshold (V4B) (see equations in the IN3–IN6 section). 0Ah 800Ah [7:0] IN5 (MAX6870 only) secondary undervoltage/overvoltage detector threshold (V5B) (see equations in the IN3–IN6 section). 0Bh 800Bh [7:0] IN6 (MAX6870 only) secondary undervoltage/overvoltage detector threshold (V6B) (see equations in the IN3–IN6 section). 0Ch 800Ch [2] IN3 secondary overvoltage/undervoltage selection. 0 = overvoltage threshold. 1 = undervoltage threshold. [3] IN4 secondary overvoltage/undervoltage selection. 0 = overvoltage threshold. 1 = undervoltage threshold. [4] IN5 (MAX6870 only) secondary overvoltage/undervoltage selection. 0 = overvoltage threshold. 1 = undervoltage threshold. [5] IN6 (MAX6870 only) secondary overvoltage/undervoltage selection. 0 = overvoltage threshold. 1 = undervoltage threshold. [7:6] 0Dh 16 DESCRIPTION 800Dh Not used. [1] IN3 range selection. 0 = +1V to +5.5V range in 20mV increments. 1 = +0.5V to +3.05V range in 10mV increments. [2] IN4 range selection. 0 = +1V to +5.5V range in 20mV increments. 1 = +0.5V to +3.05V range in 10mV increments. [3] IN5 (MAX6870 only) range selection. 0 = +1V to +5.5V range in 20mV increments. 1 = +0.5V to +3.05V range in 10mV increments. [4] IN6 (MAX6870 only) range selection. 0 = +1V to +5.5V range in 20mV increments. 1 = +0.5V to +3.05V range in 10mV increments. [5] Not used. ______________________________________________________________________________________ EEPROM-Programmable Hex/Quad Power-Supply Sequencers/Supervisors with ADC Table 5. ADC Registers for AUXIN1 and AUXIN2 (Read Only) REGISTER ADDRESS 5Ch 5Dh 5Eh 5Fh BIT RANGE DESCRIPTION [7:0] AUXIN1 measured value, 8 MSBs. [1:0] AUXIN1 measured value, 2 LSBs. [7:2] Not used. [7:0] AUXIN2 measured value, 8 MSBs. [1:0] AUXIN2 measured value, 2 LSBs. [7:2] Not used. Table 6. GPI1–GPI4 Active Logic States REGISTER ADDRESS 3Bh BIT RANGE 5). AUXIN1 and AUXIN2 do not assert any of the programmable outputs. The AUXIN1 and AUXIN2 inputs accept power-supply voltages or other system voltages scaled to the +1.25V ADC input voltage range. GPI1–GPI4 The GPI1–GPI4 programmable logic inputs control power-supply sequencing (programmable outputs), reset/interrupt signaling, and watchdog functions (see the Configuring the Watchdog Timers (Registers 3Ch–3Fh) section). Configure GPI1–GPI4 for active-low or active-high logic (Table 6). GPI1–GPI4 internally pull down to GND through a 10µA current sink. MR The manual reset (MR) input initiates a reset condition. Register 40h determines the programmable outputs that assert while MR is low (Table 7). All affected programmable outputs remain asserted (see the Programmable Outputs section) for their PO_ timeout periods after MR releases high. An internal 10µA current source pulls MR to DBP. Leave MR unconnected or connect to DBP if unused. A programmable output cannot depend solely on MR. DESCRIPTION [0] GPI1. 0 = active low. 1 = active high. [1] GPI2. 0 = active low. 1 = active high. [2] GPI3. 0 = active low. 1 = active high. [3] GPI4. 0 = active low. 1 = active high. Table 7. Programmable Output Behavior and MR REGISTER ADDRESS 40h EEPROM MEMORY ADDRESS 8040h BIT RANGE DESCRIPTION [0] PO1 (MAX6870 only). 0 = PO1 independent of MR. 1 = PO1 asserts when MR = low. [1] PO2 (MAX6870 only). 0 = PO2 independent of MR. 1 = PO2 asserts when MR = low. [2] PO3 (MAX6870)/PO1 (MAX6871). 0 = PO3/PO1 independent of MR. 1 = PO3/PO1 asserts when MR = low. [3] PO4 (MAX6870)/PO2 (MAX6871). 0 = PO4/PO2 independent of MR. 1 = PO4/PO2 asserts when MR = low. [4] PO5 (MAX6870)/PO3 (MAX6871). 0 = PO5/PO3 independent of MR. 1 = PO5/PO3 asserts when MR = low. [5] PO6 (MAX6870)/PO4 (MAX6871). 0 = PO6/PO4 independent of MR. 1 = PO6/PO4 asserts when MR = low. [6] PO7 (MAX6870)/PO5 (MAX6871). 0 = PO7/PO5 independent of MR. 1 = PO7/PO5 asserts when MR = low. [7] PO8 (MAX6870 only). 0 = PO8 independent of MR. 1 = PO8 asserts when MR = low. ______________________________________________________________________________________ 17 MAX6870/MAX6871 AUXIN1 and AUXIN2 The AUXIN1 and AUXIN2 high-impedance analog inputs are intended to monitor two additional system voltages not required for power-supply sequencing or reset purposes. The internal 10-bit ADC monitors AUXIN1 and AUXIN2 and stores the data in the ADC registers (Table MAX6870/MAX6871 EEPROM-Programmable Hex/Quad Power-Supply Sequencers/Supervisors with ADC MARGIN MARGIN allows system-level testing while power supplies exceed the normal ranges. Registers 41h and 42h determine whether the programmable outputs assert to a predetermined state or hold the last state as MARGIN is driven low (Table 8). Drive MARGIN low to set the programmable outputs in a known state while system- level testing occurs. Leave MARGIN unconnected or connect to DBP if unused. An internal 10µA current source pulls MARGIN to DBP. The internal ADC continually monitors IN_ while MARGIN is low. The state of each programmable output does not change while MARGIN = GND. MARGIN overrides MR if both assert at the same time. Table 8. Programmable Output Behavior and MARGIN REGISTER ADDRESS 41h 42h 18 EEPROM MEMORY ADDRESS BIT RANGE AFFECTED OUTPUT [0] PO1 (MAX6870 only) 0 = output held in existing state. 1 = output asserts high or low (see 42h[0]). [1] PO2 (MAX6870 only) 0 = output held in existing state. 1 = output asserts high or low (see 42h[1]). [2] PO3 (MAX6870) PO1 (MAX6871) 0 = output held in existing state. 1 = output asserts high or low (see 42h[2]). [3] PO4 (MAX6870) PO2 (MAX6871) 0 = output held in existing state. 1 = output asserts high or low (see 42h[3]). [4] PO5 (MAX6870) PO3 (MAX6871) 0 = output held in existing state. 1 = output asserts high or low (see 42h[4]). [5] PO6 (MAX6870) PO4 (MAX6871) 0 = output held in existing state. 1 = output asserts high or low (see 42h[5]). [6] PO7 (MAX6870) PO5 (MAX6871) 0 = output held in existing state. 1 = output asserts high or low (see 42h[6]). [7] PO8 (MAX6870 only) 0 = output held in existing state. 1 = output asserts high or low (see 42h[7]). [0] PO1 (MAX6870 only) 0 = output asserts low if 41h[0] = 1. 1 = output asserts high if 41h[0] = 1. [1] PO2 (MAX6870 only) 0 = output asserts low if 41h[1] = 1. 1 = output asserts high if 41h[1] = 1. [2] PO3 (MAX6870) PO1 (MAX6871) 0 = output asserts low if 41h[2] = 1. 1 = output asserts high if 41h[2] = 1. [3] PO4 (MAX6870) PO2 (MAX6871) 0 = output asserts low if 41h[3] = 1. 1 = output asserts high if 41h[3] = 1. [4] PO5 (MAX6870) PO3 (MAX6871) 0 = output asserts low if 41h[4] = 1. 1 = output asserts high if 41h[4] = 1. [5] PO6 (MAX6870) PO4 (MAX6871) 0 = output asserts low if 41h[5] = 1. 1 = output asserts high if 41h[5] = 1. [6] PO7 (MAX6870) PO5 (MAX6871) 0 = output asserts low if 41h[6] = 1. 1 = output asserts high if 41h[6] = 1. [7] PO8 (MAX6870 only) 0 = output asserts low if 41h[7] = 1. 1 = output asserts high if 41h[7] = 1. DESCRIPTION 8041h 8042h ______________________________________________________________________________________ EEPROM-Programmable Hex/Quad Power-Supply Sequencers/Supervisors with ADC Table 9. Reference Register REGISTER ADDRESS EEPROM MEMORY ADDRESS 44h 8044h BIT RANGE DESCRIPTION [0] 0 = internal reference. 1 = external reference. [7:1] Not used. Programmable Outputs The MAX6870 features eight programmable outputs, while the MAX6871 features five programmable outputs. Selectable output-stage configurations include: active low or active high, open drain, weak pullup, push-pull, or charge pump. During power-up, the programmable outputs pull to GND with an internal 10µA current sink for 1V < VABP < VUVLO. The programmable outputs remain in their active states until PO_ timeout period expires, and all of the programmed conditions are met for each output. Any output programmed to depend on no condition always remains in its active state (Table 22). An activehigh configured output is considered asserted when that output is logic-high. No output can depend solely on MR. The positive voltage monitors generate fault signals (logical 0) to the MAX6870/MAX6871’s logic array when an input voltage is below the programmed undervoltage threshold, or when that voltage is above the overvoltage threshold. The negative voltage monitor (IN2) generates a fault signal to the logic array when the input voltage is less negative than the undervoltage threshold, or when that voltage is more negative than the overvoltage threshold. Registers 0Eh through 3Ah and 40h configure each of the programmable outputs. Programmable timing blocks set the PO_ timeout period from 25µs to 1600ms for each programmable output. See register 3Ah (Table 22) to set the active state (active-high or active-low) for each programmable output and registers 11h, 15h, 1Ch, 23h, 2Ah, 31h, 35h, and 39h to select the output stage types (Tables 23 and 24), and PO_ timeout periods (Table 25) for each output. Control selected programmable outputs with a sum of products (Tables 10–21). Each product allows a different set of conditions to assert each output. Outputs PO3 (MAX6870)/PO1 (MAX6871) and PO6 (MAX6870)/ PO4 (MAX6871) allow two sets of different conditions to assert each output. Outputs PO1 and PO2 (MAX6870 only), PO7 (MAX6870)/PO5 (MAX6871), and PO8 (MAX6870 only) allow only one set of conditions to assert each output. For example, Product 1 of the PO3 (MAX6870—Table 12) programmable output may depend on the IN1 primary undervoltage threshold, and the states of GPI1, PO1, and PO2. Write a one to R16h[0], R17h[6], and R18h[3:2] to configure Product 1 as indicated. IN1 must be above the primary undervoltage threshold (Table 2), GPI1 must be inactive (Table 6), and PO1 (Tables 10 and 22) and PO2 (Tables 12 and 23) must be in their deasserted states for Product 1 to be a logical 1. Product 1 is equivalent to the logic statement: V1A • GPI1 • PO1 • PO2. Product 2 of PO3 (MAX6870, Table 13) may depend on an entirely different set of conditions, or the same conditions, depending on the system requirements. For example, Product 2 may depend on the IN1 undervoltage threshold, and the states of GPI2 and WDI1. Write ones to R19h[6, 0] and R1Ah[7] to configure Product 2 as indicated. IN1 must be above the primary undervoltage threshold (Table 2), GPI2 must be inactive (Table 6), and the WDI1 timer must not have expired (Tables 27 and 28) for Product 2 to be a logical 1. Product 2 is equivalent to the logic statement: V1A • GPI2 • WDI1. PO3 deasserts if either Product 1 or Product 2 is a logical 1. The logical statement: Product 1 + Product 2 determines the state of PO3. ______________________________________________________________________________________ 19 MAX6870/MAX6871 REFIN The MAX6870/MAX6871 feature an internal +1.25V voltage reference. The voltage reference sets the threshold of the voltage detectors and provides a reference voltage for the internal ADC. Program register 44h to use the internal reference or an external reference (Table 9). Leave REFIN unconnected when using the internal reference. REFIN accepts an external reference in the +1.225V to +1.275V range. MAX6870/MAX6871 EEPROM-Programmable Hex/Quad Power-Supply Sequencers/Supervisors with ADC Table 10. PO1 (MAX6870 Only) Output Dependency REGISTER ADDRESS 0Eh 0Fh 10h EEPROM MEMORY ADDRESS 800Eh 800Fh 8010h BIT OUTPUT ASSERTION CONDITIONS [0] 1 = PO1 assertion depends on IN1 primary undervoltage threshold (Table 2). [1] 1 = PO1 assertion depends on IN2 primary undervoltage threshold (Table 3). [2] 1 = PO1 assertion depends on IN3 primary undervoltage threshold (Table 4). [3] 1 = PO1 assertion depends on IN4 primary undervoltage threshold (Table 4). [4] 1 = PO1 assertion depends on IN5 primary undervoltage threshold (Table 4). [5] 1 = PO1 assertion depends on IN6 primary undervoltage threshold (Table 4). [6] 1 = PO1 assertion depends on watchdog 1 (Tables 27 and 28). [7] 1 = PO1 assertion depends on watchdog 2 (Tables 27 and 28). [0] 1 = PO1 assertion depends on IN1 secondary undervoltage/overvoltage threshold (Table 2). [1] 1 = PO1 assertion depends on IN2 secondary undervoltage/overvoltage threshold (Table 3). [2] 1 = PO1 assertion depends on IN3 secondary undervoltage/overvoltage threshold (Table 4). [3] 1 = PO1 assertion depends on IN4 secondary undervoltage/overvoltage threshold (Table 4). [4] 1 = PO1 assertion depends on IN5 secondary undervoltage/overvoltage threshold (Table 4). [5] 1 = PO1 assertion depends on IN6 secondary undervoltage/overvoltage threshold (Table 4). [6] 1 = PO1 assertion depends on GPI1 (Table 6). [7] 1 = PO1 assertion depends on GPI2 (Table 6). [0] 1 = PO1 assertion depends on GPI3 (Table 6). [1] 1 = PO1 assertion depends on GPI4 (Table 6). [2] 1 = PO1 assertion depends on PO2 (Table 11). [3] 1 = PO1 assertion depends on PO3 (Tables 12 and 13). [4] 1 = PO1 assertion depends on PO4 (Tables 14 and 15). [5] 1 = PO1 assertion depends on PO5 (Tables 16 and 17). [6] 1 = PO1 assertion depends on PO6 (Tables 18 and 19). [7] 1 = PO1 assertion depends on PO7 (Table 20). 11h 8011h [0] 1 = PO1 assertion depends on PO8 (Table 21). 40h 8040h [0] 1 = PO1 asserts when MR = low (Table 7). Table 10 only applies to PO1 of the MAX6870. Write a 0 to a bit to make the PO1 output independent of the respective signal (IN1–IN6 primary or secondary 20 thresholds, WDI1 or WDI2, GPI1–GPI4, MR, or other programmable outputs). ______________________________________________________________________________________ EEPROM-Programmable Hex/Quad Power-Supply Sequencers/Supervisors with ADC REGISTER ADDRESS 12h 13h 14h EEPROM MEMORY ADDRESS 8012h 8013h 8014h BIT MAX6870/MAX6871 Table 11. PO2 (MAX6870 Only) Output Dependency OUTPUT ASSERTION CONDITIONS [0] 1 = PO2 assertion depends on IN1 primary undervoltage threshold (Table 2). [1] 1 = PO2 assertion depends on IN2 primary undervoltage threshold (Table 3). [2] 1 = PO2 assertion depends on IN3 primary undervoltage threshold (Table 4). [3] 1 = PO2 assertion depends on IN4 primary undervoltage threshold (Table 4). [4] 1 = PO2 assertion depends on IN5 primary undervoltage threshold (Table 4). [5] 1 = PO2 assertion depends on IN6 primary undervoltage threshold (Table 4). [6] 1 = PO2 assertion depends on watchdog 1 (Tables 27 and 28). [7] 1 = PO2 assertion depends on watchdog 2 (Tables 27 and 28). [0] 1 = PO2 assertion depends on IN1 secondary undervoltage/overvoltage threshold (Table 2). [1] 1 = PO2 assertion depends on IN2 secondary undervoltage/overvoltage threshold (Table 3). [2] 1 = PO2 assertion depends on IN3 secondary undervoltage/overvoltage threshold (Table 4). [3] 1 = PO2 assertion depends on IN4 secondary undervoltage/overvoltage threshold (Table 4). [4] 1 = PO2 assertion depends on IN5 secondary undervoltage/overvoltage threshold (Table 4). [5] 1 = PO2 assertion depends on IN6 secondary undervoltage/overvoltage threshold (Table 4). [6] 1 = PO2 assertion depends on GPI1 (Table 6). [7] 1 = PO2 assertion depends on GPI2 (Table 6). [0] 1 = PO2 assertion depends on GPI3 (Table 6). [1] 1 = PO2 assertion depends on GPI4 (Table 6). [2] 1 = PO2 assertion depends on PO1 (Table 10). [3] 1 = PO2 assertion depends on PO3 (Tables 12 and 13). [4] 1 = PO2 assertion depends on PO4 (Tables 14 and 15). [5] 1 = PO2 assertion depends on PO5 (Tables 16 and 17). [6] 1 = PO2 assertion depends on PO6 (Tables 18 and 19). [7] 1 = PO2 assertion depends on PO7 (Table 20). 15h 8015h [0] 1 = PO2 assertion depends on PO8 (Table 21). 40h 8040h [1] 1 = PO2 asserts when MR = low (Table 7). Table 11 only applies to PO2 of the MAX6870. Write a 0 to a bit to make the PO2 output independent of the respective signal (IN1–IN6 primary or secondary thresholds, WDI1 or WDI2, GPI1–GPI4, MR, or other programmable outputs). ______________________________________________________________________________________ 21 MAX6870/MAX6871 EEPROM-Programmable Hex/Quad Power-Supply Sequencers/Supervisors with ADC Table 12. PO3 (MAX6870)/PO1 (MAX6871) Output Dependency (Product 1) REGISTER ADDRESS 16h 17h 18h EEPROM MEMORY ADDRESS 8016h 8017h 8018h BIT OUTPUT ASSERTION CONDITIONS [0] 1 = PO3/PO1 assertion depends on IN1 primary undervoltage threshold (Table 2). [1] 1 = PO3/PO1 assertion depends on IN2 primary undervoltage threshold (Table 3). [2] 1 = PO3/PO1 assertion depends on IN3 primary undervoltage threshold (Table 4). [3] 1 = PO3/PO1 assertion depends on IN4 primary undervoltage threshold (Table 4). [4] 1 = PO3 (MAX6870 only) assertion depends on IN5 primary undervoltage threshold (Table 4). Must be set to 0 for the MAX6871. [5] 1 = PO3 (MAX6870 only) assertion depends on IN6 primary undervoltage threshold (Table 4). Must be set to 0 for the MAX6871. [6] 1 = PO3/PO1 assertion depends on watchdog 1 (Tables 27 and 28). [7] 1 = PO3/PO1 assertion depends on watchdog 2 (Tables 27 and 28). [0] 1 = PO3/PO1 assertion depends on IN1 secondary undervoltage/overvoltage threshold (Table 2). [1] 1 = PO3/PO1 assertion depends on IN2 secondary undervoltage/overvoltage threshold (Table 3). [2] 1 = PO3/PO1 assertion depends on IN3 secondary undervoltage/overvoltage threshold (Table 4). [3] 1 = PO3/PO1 assertion depends on IN4 secondary undervoltage/overvoltage threshold (Table 4). [4] 1 = PO3 (MAX6870 only) assertion depends on IN5 secondary undervoltage/overvoltage threshold (Table 4). Must be set to 0 for the MAX6871. [5] 1 = PO3 (MAX6870 only) assertion depends on IN6 secondary undervoltage/overvoltage threshold (Table 4). Must be set to 0 for the MAX6871. [6] 1 = PO3/PO1 assertion depends on GPI1 (Table 6). [7] 1 = PO3/PO1 assertion depends on GPI2 (Table 6). [0] 1 = PO3/PO1 assertion depends on GPI3 (Table 6). [1] 1 = PO3/PO1 assertion depends on GPI4 (Table 6). [2] 1 = PO3 (MAX6870 only) assertion depends on PO1 (Table 10). Must be set to 0 for the MAX6871. [3] 1 = PO3 (MAX6870 only) assertion depends on PO2 (Table 11). Must be set to 0 for the MAX6871. [4] 1 = PO3/PO1 assertion depends on PO4 (MAX6870)/PO2 (MAX6871) (Tables 14 and 15). [5] 1 = PO3/PO1 assertion depends on PO5 (MAX6870)/PO3 (MAX6871) (Tables 16 and 17). [6] 1 = PO3/PO1 assertion depends on PO6 (MAX6870)/PO4 (MAX6871) (Tables 18 and 19). [7] 1 = PO3/PO1 assertion depends on PO7 (MAX6870)/PO5 (MAX6871) (Table 20). 1Ch 801Ch [0] 1 = PO3 (MAX6870 only) assertion depends on PO8 (Table 21). Must be set to 0 for the MAX6871. 40h 8040h [2] 1 = PO3/PO1 asserts when MR = low (Table 7). Table 12 only applies to PO3 of the MAX6870 and PO1 of the MAX6871. Write a 0 to a bit to make the PO3/PO1 output independent of the respective signal (IN_ primary or secondary thresholds, WDI1 or WDI2, GPI1–GPI4, 22 MR, or other programmable outputs). See Table 13 for Product 2. PO3 (MAX6870)/PO1 (MAX6871) deasserts when Product 1 or Product 2 = 1. ______________________________________________________________________________________ EEPROM-Programmable Hex/Quad Power-Supply Sequencers/Supervisors with ADC REGISTER ADDRESS 19h 1Ah 1Bh EEPROM MEMORY ADDRESS 8019h 801Ah 801Bh BIT MAX6870/MAX6871 Table 13. PO3 (MAX6870)/PO1 (MAX6871) Output Dependency (Product 2) OUTPUT ASSERTION CONDITIONS [0] 1 = PO3/PO1 assertion depends on IN1 primary undervoltage threshold (Table 2). [1] 1 = PO3/PO1 assertion depends on IN2 primary undervoltage threshold (Table 3). [2] 1 = PO3/PO1 assertion depends on IN3 primary undervoltage threshold (Table 4). [3] 1 = PO3/PO1 assertion depends on IN4 primary undervoltage threshold (Table 4). [4] 1 = PO3 (MAX6870 only) assertion depends on IN5 primary undervoltage threshold (Table 4). Must be set to 0 for the MAX6871. [5] 1 = PO3 (MAX6870 only) assertion depends on IN6 primary undervoltage threshold (Table 4). Must be set to 0 for the MAX6871. [6] 1 = PO3/PO1 assertion depends on watchdog 1 (Tables 27 and 28). [7] 1 = PO3/PO1 assertion depends on watchdog 2 (Tables 27 and 28). [0] 1 = PO3/PO1 assertion depends on IN1 secondary undervoltage/overvoltage threshold (Table 2). [1] 1 = PO3/PO1 assertion depends on IN2 secondary undervoltage/overvoltage threshold (Table 3). [2] 1 = PO3/PO1 assertion depends on IN3 secondary undervoltage/overvoltage threshold (Table 4). [3] 1 = PO3/PO1 assertion depends on IN4 secondary undervoltage/overvoltage threshold (Table 4). [4] 1 = PO3 (MAX6870 only) assertion depends on IN5 secondary undervoltage/overvoltage threshold (Table 4). Must be set to 0 for the MAX6871. [5] 1 = PO3 (MAX6870 only) assertion depends on IN6 secondary undervoltage/overvoltage threshold (Table 4). Must be set to 0 for the MAX6871. [6] 1 = PO3/PO1 assertion depends on GPI1 (Table 6). [7] 1 = PO3/PO1 assertion depends on GPI2 (Table 6). [0] 1 = PO3/PO1 assertion depends on GPI3 (Table 6). [1] 1 = PO3/PO1 assertion depends on GPI4 (Table 6). [2] 1 = PO3 (MAX6870 only) assertion depends on PO1 (Table 10). Must be set to 0 for the MAX6871. [3] 1 = PO3 (MAX6870 only) assertion depends on PO2 (Table 11). Must be set to 0 for the MAX6871. [4] 1 = PO3/PO1 assertion depends on PO4 (MAX6870)/PO2 (MAX6871) (Tables 14 and 15). [5] 1 = PO3/PO1 assertion depends on PO5 (MAX6870)/PO3 (MAX6871) (Tables 16 and 17). [6] 1 = PO3/PO1 assertion depends on PO6 (MAX6870)/PO4 (MAX6871) (Tables 18 and 19). [7] 1 = PO3/PO1 assertion depends on PO7 (MAX6870)/PO5 (MAX6871) (Table 20). 1Ch 801Ch [1] 1 = PO3 (MAX6870 only) assertion depends on PO8 (Table 21). Must be set to 0 for the MAX6871. 40h 8040h [2] 1 = PO3/PO1 asserts when MR = low (Table 7). Table 13 only applies to PO3 of the MAX6870 and PO1 of the MAX6871. Write a 0 to a bit to make the PO3/PO1 output independent of the respective signal (IN_ primary or secondary thresholds, WDI1 or WDI2, GPI1–GPI4, MR, or other programmable outputs). See Table 12 for Product 1. PO3 (MAX6870)/PO1 (MAX6871) deasserts when Product 1 or Product 2 = 1. ______________________________________________________________________________________ 23 MAX6870/MAX6871 EEPROM-Programmable Hex/Quad Power-Supply Sequencers/Supervisors with ADC Table 14. PO4 (MAX6870)/PO2 (MAX6871) Output Dependency (Product 1) REGISTER ADDRESS 1Dh 1Eh 1Fh EEPROM MEMORY ADDRESS 801Dh 801Eh 801Fh BIT OUTPUT ASSERTION CONDITIONS [0] 1 = PO4/PO2 assertion depends on IN1 primary undervoltage threshold (Table 2). [1] 1 = PO4/PO2 assertion depends on IN2 primary undervoltage threshold (Table 3). [2] 1 = PO4/PO2 assertion depends on IN3 primary undervoltage threshold (Table 4). [3] 1 = PO4/PO2 assertion depends on IN4 primary undervoltage threshold (Table 4). [4] 1 = PO4 (MAX6870 only) assertion depends on IN5 primary undervoltage threshold (Table 4). Must be set to 0 for the MAX6871. [5] 1 = PO4 (MAX6870 only) assertion depends on IN6 primary undervoltage threshold (Table 4). Must be set to 0 for the MAX6871. [6] 1 = PO4/PO2 assertion depends on watchdog 1 (Tables 27 and 28). [7] 1 = PO4/PO2 assertion depends on watchdog 2 (Tables 27 and 28). [0] 1 = PO4/PO2 assertion depends on IN1 secondary undervoltage/overvoltage threshold (Table 2). [1] 1 = PO4/PO2 assertion depends on IN2 secondary undervoltage/overvoltage threshold (Table 3). [2] 1 = PO4/PO2 assertion depends on IN3 secondary undervoltage/overvoltage threshold (Table 4). [3] 1 = PO4/PO2 assertion depends on IN4 secondary undervoltage/overvoltage threshold (Table 4). [4] 1 = PO4 (MAX6870 only) assertion depends on IN5 secondary undervoltage/overvoltage threshold (Table 4). Must be set to 0 for the MAX6871. [5] 1 = PO4 (MAX6870 only) assertion depends on IN6 secondary undervoltage/overvoltage threshold (Table 4). Must be set to 0 for the MAX6871. [6] 1 = PO4/PO2 assertion depends on GPI1 (Table 6). [7] 1 = PO4/PO2 assertion depends on GPI2 (Table 6). [0] 1 = PO4/PO2 assertion depends on GPI3 (Table 6). [1] 1 = PO4/PO2 assertion depends on GPI4 (Table 6). [2] 1 = PO4 (MAX6870 only) assertion depends on PO1 (Table 10). Must be set to 0 for the MAX6871. [3] 1 = PO4 (MAX6870 only) assertion depends on PO2 (Table 11). Must be set to 0 for the MAX6871. [4] 1 = PO4/PO2 assertion depends on PO3 (MAX6870)/PO1 (MAX6871) (Tables 12 and 13). [5] 1 = PO4/PO2 assertion depends on PO5 (MAX6870)/PO3 (MAX6871) (Tables 16 and 17). [6] 1 = PO4/PO2 assertion depends on PO6 (MAX6870)/PO4 (MAX6871) (Tables 18 and 19). [7] 1 = PO4/PO2 assertion depends on PO7 (MAX6870)/PO5 (MAX6871) (Table 20). 23h 8023h [0] 1 = PO4 (MAX6870 only) assertion depends on PO8 (Table 21). Must be set to 0 for the MAX6871. 40h 8040h [3] 1 = PO4/PO2 asserts when MR = low (Table 7). Table 14 only applies to PO4 of the MAX6870 and PO2 of the MAX6871. Write a 0 to a bit to make the PO4/PO2 output independent of the respective signal (IN_ primary or secondary thresholds, WDI1 or WDI2, GPI1–GPI4, 24 MR, or other programmable outputs). See Table 15 for Product 2. PO4 (MAX6870)/PO2 (MAX6871) deasserts when Product 1 or Product 2 = 1. ______________________________________________________________________________________ EEPROM-Programmable Hex/Quad Power-Supply Sequencers/Supervisors with ADC REGISTER ADDRESS 20h 21h 22h EEPROM MEMORY ADDRESS 8020h 8021h 8022h BIT OUTPUT ASSERTION CONDITIONS [0] 1 = PO4/PO2 assertion depends on IN1 primary undervoltage threshold (Table 2). [1] 1 = PO4/PO2 assertion depends on IN2 primary undervoltage threshold (Table 3). [2] 1 = PO4/PO2 assertion depends on IN3 primary undervoltage threshold (Table 4). [3] 1 = PO4/PO2 assertion depends on IN4 primary undervoltage threshold (Table 4). [4] 1 = PO4 (MAX6870 only) assertion depends on IN5 primary undervoltage threshold (Table 4). Must be set to 0 for the MAX6871. [5] 1 = PO4 (MAX6870 only) assertion depends on IN6 primary undervoltage threshold (Table 4). Must be set to 0 for the MAX6871. [6] 1 = PO4/PO2 assertion depends on watchdog 1 (Tables 27 and 28). [7] 1 = PO4/PO2 assertion depends on watchdog 2 (Tables 27 and 28). [0] 1 = PO4/PO2 assertion depends on IN1 secondary undervoltage/overvoltage threshold (Table 2). [1] 1 = PO4/PO2 assertion depends on IN2 secondary undervoltage/overvoltage threshold (Table 3). [2] 1 = PO4/PO2 assertion depends on IN3 secondary undervoltage/overvoltage threshold (Table 4). [3] 1 = PO4/PO2 assertion depends on IN4 secondary undervoltage/overvoltage threshold (Table 4). [4] 1 = PO4 (MAX6870 only) assertion depends on IN5 secondary undervoltage/overvoltage threshold (Table 4). Must be set to 0 for the MAX6871. [5] 1 = PO4 (MAX6870 only) assertion depends on IN6 secondary undervoltage/overvoltage threshold (Table 4). Must be set to 0 for the MAX6871. [6] 1 = PO4/PO2 assertion depends on GPI1 (Table 6). [7] 1 = PO4/PO2 assertion depends on GPI2 (Table 6). [0] 1 = PO4/PO2 assertion depends on GPI3 (Table 6). [1] 1 = PO4/PO2 assertion depends on GPI4 (Table 6). [2] 1 = PO4 (MAX6870 only) assertion depends on PO1 (Table 10). Must be set to 0 for the MAX6871. [3] 1 = PO4 (MAX6870 only) assertion depends on PO2 (Table 11). Must be set to 0 for the MAX6871. [4] 1 = PO4/PO2 assertion depends on PO3 (MAX6870)/PO1 (MAX6871) (Tables 12 and 13). [5] 1 = PO4/PO2 assertion depends on PO5 (MAX6870)/PO3 (MAX6871) (Tables 16 and 17). [6] 1 = PO4/PO2 assertion depends on PO6 (MAX6870)/PO4 (MAX6871) (Tables 18 and 19). [7] 1 = PO4/PO2 assertion depends on PO7 (MAX6870)/PO5 (MAX6871) (Table 20). 23h 8023h [1] 1 = PO4 (MAX6870 only) assertion depends on PO8 (Table 21). Must be set to 0 for the MAX6871. 40h 8040h [3] 1 = PO4/PO2 asserts when MR = low (Table 7). Table 15 only applies to PO4 of the MAX6870 and PO2 of the MAX6871. Write a 0 to a bit to make the PO4/PO2 output independent of the respective signal (IN_ primary or secondary thresholds, WDI1 or WDI2, GPI1 to GPI4, MR, or other programmable outputs). See Table 14 for Product 1. PO4 (MAX6870)/PO2 (MAX6871) deasserts when Product 1 or Product 2 = 1. ______________________________________________________________________________________ 25 MAX6870/MAX6871 Table 15. PO4 (MAX6870)/PO2 (MAX6871) Output Dependency (Product 2) MAX6870/MAX6871 EEPROM-Programmable Hex/Quad Power-Supply Sequencers/Supervisors with ADC Table 16. PO5 (MAX6870)/PO3 (MAX6871) Output Dependency (Product 1) REGISTER ADDRESS 24h 25h 26h EEPROM MEMORY ADDRESS 8024h 8025h 8026h BIT OUTPUT ASSERTION CONDITIONS [0] 1 = PO5/PO3 assertion depends on IN1 primary undervoltage threshold (Table 2). [1] 1 = PO5/PO3 assertion depends on IN2 primary undervoltage threshold (Table 3). [2] 1 = PO5/PO3 assertion depends on IN3 primary undervoltage threshold (Table 4). [3] 1 = PO5/PO3 assertion depends on IN4 primary undervoltage threshold (Table 4). [4] 1 = PO5 (MAX6870 only) assertion depends on IN5 primary undervoltage threshold (Table 4). Must be set to 0 for the MAX6871. [5] 1 = PO5 (MAX6870 only) assertion depends on IN6 primary undervoltage threshold (Table 4). Must be set to 0 for the MAX6871. [6] 1 = PO5/PO3 assertion depends on watchdog 1 (Tables 27 and 28). [7] 1 = PO5/PO3 assertion depends on watchdog 2 (Tables 27 and 28). [0] 1 = PO5/PO3 assertion depends on IN1 secondary undervoltage/overvoltage threshold (Table 2). [1] 1 = PO5/PO3 assertion depends on IN2 secondary undervoltage/overvoltage threshold (Table 3). [2] 1 = PO5/PO3 assertion depends on IN3 secondary undervoltage/overvoltage threshold (Table 4). [3] 1 = PO5/PO3 assertion depends on IN4 secondary undervoltage/overvoltage threshold (Table 4). [4] 1 = PO5 (MAX6870 only) assertion depends on IN5 secondary undervoltage/overvoltage threshold (Table 4). Must be set to 0 for the MAX6871. [5] 1 = PO5 (MAX6870 only) assertion depends on IN6 secondary undervoltage/overvoltage threshold (Table 4). Must be set to 0 for the MAX6871. [6] 1 = PO5/PO3 assertion depends on GPI1 (Table 6). [7] 1 = PO5/PO3 assertion depends on GPI2 (Table 6). [0] 1 = PO5/PO3 assertion depends on GPI3 (Table 6). [1] 1 = PO5/PO3 assertion depends on GPI4 (Table 6). [2] 1 = PO5 (MAX6870 only) assertion depends on PO1 (Table 10). Must be set to 0 for the MAX6871. [3] 1 = PO5 (MAX6870 only) assertion depends on PO2 (Table 11). Must be set to 0 for the MAX6871. [4] 1 = PO5/PO3 assertion depends on PO3 (MAX6870)/PO1 (MAX6871) (Tables 12 and 13). [5] 1 = PO5/PO3 assertion depends on PO4 (MAX6870)/PO2 (MAX6871) (Tables 14 and 15). [6] 1 = PO5/PO3 assertion depends on PO6 (MAX6870)/PO4 (MAX6871) (Tables 18 and 19). [7] 1 = PO5/PO3 assertion depends on PO7 (MAX6870)/PO5 (MAX6871) (Table 20). 2Ah 802Ah [0] 1 = PO5 (MAX6870 only) assertion depends on PO8 (Table 21). Must be set to 0 for the MAX6871. 40h 8040h [4] 1 = PO5/PO3 asserts when MR = low (Table 7). Table 16 only applies to PO5 of the MAX6870 and PO3 of the MAX6871. Write a 0 to a bit to make the PO5/PO3 output independent of the respective signal (IN_ primary or secondary thresholds, WDI1 or WDI2, GPI1–GPI4, 26 MR, or other programmable outputs). See Table 17 for Product 2. PO5 (MAX6870)/PO3 (MAX6871) deasserts when Product 1 or Product 2 = 1. ______________________________________________________________________________________ EEPROM-Programmable Hex/Quad Power-Supply Sequencers/Supervisors with ADC REGISTER ADDRESS 27h 28h 29h EEPROM MEMORY ADDRESS 8027h 8028h 8029h BIT OUTPUT ASSERTION CONDITIONS [0] 1 = PO5/PO3 assertion depends on IN1 primary undervoltage threshold (Table 2). [1] 1 = PO5/PO3 assertion depends on IN2 primary undervoltage threshold (Table 3). [2] 1 = PO5/PO3 assertion depends on IN3 primary undervoltage threshold (Table 4). [3] 1 = PO5/PO3 assertion depends on IN4 primary undervoltage threshold (Table 4). [4] 1 = PO5 (MAX6870 only) assertion depends on IN5 primary undervoltage threshold (Table 4). Must be set to 0 for the MAX6871. [5] 1 = PO5 (MAX6870 only) assertion depends on IN6 primary undervoltage threshold (Table 4). Must be set to 0 for the MAX6871. [6] 1 = PO5/PO3 assertion depends on watchdog 1 (Tables 27 and 28). [7] 1 = PO5/PO3 assertion depends on watchdog 2 (Tables 27 and 28). [0] 1 = PO5/PO3 assertion depends on IN1 secondary undervoltage/overvoltage threshold (Table 2). [1] 1 = PO5/PO3 assertion depends on IN2 secondary undervoltage/overvoltage threshold (Table 3). [2] 1 = PO5/PO3 assertion depends on IN3 secondary undervoltage/overvoltage threshold (Table 4). [3] 1 = PO5/PO3 assertion depends on IN4 secondary undervoltage/overvoltage threshold (Table 4). [4] 1 = PO5 (MAX6870 only) assertion depends on IN5 secondary undervoltage/overvoltage threshold (Table 4). Must be set to 0 for the MAX6871. [5] 1 = PO5 (MAX6870 only) assertion depends on IN6 secondary undervoltage/overvoltage threshold (Table 4). Must be set to 0 for the MAX6871. [6] 1 = PO5/PO3 assertion depends on GPI1 (Table 6). [7] 1 = PO5/PO3 assertion depends on GPI2 (Table 6). [0] 1 = PO5/PO3 assertion depends on GPI3 (Table 6). [1] 1 = PO5/PO3 assertion depends on GPI4 (Table 6). [2] 1 = PO5 (MAX6870 only) assertion depends on PO1 (Table 10). Must be set to 0 for the MAX6871. [3] 1 = PO5 (MAX6870 only) assertion depends on PO2 (Table 11). Must be set to 0 for the MAX6871. [4] 1 = PO5/PO3 assertion depends on PO3 (MAX6870)/PO1 (MAX6871) (Tables 12 and 13). [5] 1 = PO5/PO3 assertion depends on PO4 (MAX6870)/PO2 (MAX6871) (Tables 14 and 15). [6] 1 = PO5/PO3 assertion depends on PO6 (MAX6870)/PO4 (MAX6871) (Tables 18 and 19). [7] 1 = PO5/PO3 assertion depends on PO7 (MAX6870)/PO5 (MAX6871) (Table 20). 3Bh 803Bh [4] 1 = PO5 (MAX6870 only) assertion depends on PO8 (Table 21). Must be set to 0 for the MAX6871. 40h 8040h [4] 1 = PO5/PO3 asserts when MR = low (Table 7). Table 17 only applies to PO5 of the MAX6870 and PO3 of the MAX6871. Write a 0 to a bit to make the PO5/PO3 output independent of the respective signal (IN_ primary or secondary thresholds, WDI1 or WDI2, GPI1–GPI4, MR, or other programmable outputs). See Table 16 for Product 1. PO5 (MAX6870)/PO3 (MAX6871) deasserts when Product 1 or Product 2 = 1. ______________________________________________________________________________________ 27 MAX6870/MAX6871 Table 17. PO5 (MAX6870)/PO3 (MAX6871) Output Dependency (Product 2) MAX6870/MAX6871 EEPROM-Programmable Hex/Quad Power-Supply Sequencers/Supervisors with ADC Table 18. PO6 (MAX6870)/PO4 (MAX6871) Output Dependency (Product 1) REGISTER ADDRESS 2Bh 2Ch 2Dh EEPROM MEMORY ADDRESS 802Bh 802Ch 802Dh BIT OUTPUT ASSERTION CONDITIONS [0] 1 = PO6/PO4 assertion depends on IN1 primary undervoltage threshold (Table 2). [1] 1 = PO6/PO4 assertion depends on IN2 primary undervoltage threshold (Table 3). [2] 1 = PO6/PO4 assertion depends on IN3 primary undervoltage threshold (Table 4). [3] 1 = PO6/PO4 assertion depends on IN4 primary undervoltage threshold (Table 4). [4] 1 = PO6 (MAX6870 only) assertion depends on IN5 primary undervoltage threshold (Table 4). Must be set to 0 for the MAX6871. [5] 1 = PO6 (MAX6870 only) assertion depends on IN6 primary undervoltage threshold (Table 4). Must be set to 0 for the MAX6871. [6] 1 = PO6/PO4 assertion depends on watchdog 1 (Tables 27 and 28). [7] 1 = PO6/PO4 assertion depends on watchdog 2 (Tables 27 and 28). [0] 1 = PO6/PO4 assertion depends on IN1 secondary undervoltage/overvoltage threshold (Table 2). [1] 1 = PO6/PO4 assertion depends on IN2 secondary undervoltage/overvoltage threshold (Table 3). [2] 1 = PO6/PO4 assertion depends on IN3 secondary undervoltage/overvoltage threshold (Table 4). [3] 1 = PO6/PO4 assertion depends on IN4 secondary undervoltage/overvoltage threshold (Table 4). [4] 1 = PO6 (MAX6870 only) assertion depends on IN5 secondary undervoltage/overvoltage threshold (Table 4). Must be set to 0 for the MAX6871. [5] 1 = PO6 (MAX6870 only) assertion depends on IN6 secondary undervoltage/overvoltage threshold (Table 4). Must be set to 0 for the MAX6871. [6] 1 = PO6/PO4 assertion depends on GPI1 (Table 6). [7] 1 = PO6/PO4 assertion depends on GPI2 (Table 6). [0] 1 = PO6/PO4 assertion depends on GPI3 (Table 6). [1] 1 = PO6/PO4 assertion depends on GPI4 (Table 6). [2] 1 = PO6 (MAX6870 only) assertion depends on PO1 (Table 10). Must be set to 0 for the MAX6871. [3] 1 = PO6 (MAX6870 only) assertion depends on PO2 (Table 11). Must be set to 0 for the MAX6871. [4] 1 = PO6/PO4 assertion depends on PO3 (MAX6870)/PO1 (MAX6871) (Tables 12 and 13). [5] 1 = PO6/PO4 assertion depends on PO4 (MAX6870)/PO2 (MAX6871) (Tables 14 and 15). [6] 1 = PO6/PO4 assertion depends on PO5 (MAX6870)/PO3 (MAX6871) (Tables 16 and 17). [7] 1 = PO6/PO4 assertion depends on PO7 (MAX6870)/PO5 (MAX6871) (Table 20). 31h 8031h [0] 1 = PO6 (MAX6870 only) assertion depends on PO8 (Table 21). Must be set to 0 for the MAX6871. 40h 8040h [5] 1 = PO6/PO4 asserts when MR = low (Table 7). Table 18 only applies to PO6 of the MAX6870 and PO4 of the MAX6871. Write a 0 to a bit to make the PO6/PO4 output independent of the respective signal (IN_ primary or secondary thresholds, WDI1 or WDI2, GPI1–GPI4, 28 MR, or other programmable outputs). See Table 19 for Product 2. PO6 (MAX6870)/PO4 (MAX6871) deasserts when Product 1 or Product 2 = 1. ______________________________________________________________________________________ EEPROM-Programmable Hex/Quad Power-Supply Sequencers/Supervisors with ADC REGISTER ADDRESS 2Eh 2Fh 30h EEPROM MEMORY ADDRESS 802Eh 802Fh 8030h BIT OUTPUT ASSERTION CONDITIONS [0] 1 = PO6/PO4 assertion depends on IN1 primary undervoltage threshold (Table 2). [1] 1 = PO6/PO4 assertion depends on IN2 primary undervoltage threshold (Table 3). [2] 1 = PO6/PO4 assertion depends on IN3 primary undervoltage threshold (Table 4). [3] 1 = PO6/PO4 assertion depends on IN4 primary undervoltage threshold (Table 4). [4] 1 = PO6 (MAX6870 only) assertion depends on IN5 primary undervoltage threshold (Table 4). Must be set to 0 for the MAX6871. [5] 1 = PO6 (MAX6870 only) assertion depends on IN6 primary undervoltage threshold (Table 4). Must be set to 0 for the MAX6871. [6] 1 = PO6/PO4 assertion depends on watchdog 1 (Tables 27 and 28). [7] 1 = PO6/PO4 assertion depends on watchdog 2 (Tables 27 and 28). [0] 1 = PO6/PO4 assertion depends on IN1 secondary undervoltage/overvoltage threshold (Table 2). [1] 1 = PO6/PO4 assertion depends on IN2 secondary undervoltage/overvoltage threshold (Table 3). [2] 1 = PO6/PO4 assertion depends on IN3 secondary undervoltage/overvoltage threshold (Table 4). [3] 1 = PO6/PO4 assertion depends on IN4 secondary undervoltage/overvoltage threshold (Table 4). [4] 1 = PO6 (MAX6870 only) assertion depends on IN5 secondary undervoltage/overvoltage threshold (Table 4). Must be set to 0 for the MAX6871. [5] 1 = PO6 (MAX6870 only) assertion depends on IN6 secondary undervoltage/overvoltage threshold (Table 4). Must be set to 0 for the MAX6871. [6] 1 = PO6/PO4 assertion depends on GPI1 (Table 6). [7] 1 = PO6/PO4 assertion depends on GPI2 (Table 6). [0] 1 = PO6/PO4 assertion depends on GPI3 (Table 6). [1] 1 = PO6/PO4 assertion depends on GPI4 (Table 6). [2] 1 = PO6 (MAX6870 only) assertion depends on PO1 (Table 10). Must be set to 0 for the MAX6871. [3] 1 = PO6 (MAX6870 only) assertion depends on PO2 (Table 11). Must be set to 0 for the MAX6871. [4] 1 = PO6/PO4 assertion depends on PO3 (MAX6870)/PO1 (MAX6871) (Tables 12 and 13). [5] 1 = PO6/PO4 assertion depends on PO4 (MAX6870)/PO2 (MAX6871) (Tables 14 and 15). [6] 1 = PO6/PO4 assertion depends on PO5 (MAX6870)/PO3 (MAX6871) (Tables 16 and 17). [7] 1 = PO6/PO4 assertion depends on PO7 (MAX6870)/PO5 (MAX6871) (Table 20). 3Bh 803Bh [5] 1 = PO6 (MAX6870 only) assertion depends on PO8 (Table 21). Must be set to 0 for the MAX6871. 40h 8040h [5] 1 = PO6/PO4 asserts when MR = low (Table 7). Table 19 only applies to PO6 of the MAX6870 and PO4 of the MAX6871. Write a 0 to a bit to make the PO6/PO4 output independent of the respective signal (IN_ primary or secondary thresholds, WDI1 or WDI2, GPI1–GPI4, MR, or other programmable outputs). See Table 18 for Product 1. PO6 (MAX6870)/PO4 (MAX6871) deasserts when Product 1 or Product 2 = 1. ______________________________________________________________________________________ 29 MAX6870/MAX6871 Table 19. PO6 (MAX6870)/PO4 (MAX6871) Output Dependency (Product 2) MAX6870/MAX6871 EEPROM-Programmable Hex/Quad Power-Supply Sequencers/Supervisors with ADC Table 20. PO7 (MAX6870)/PO5 (MAX6871) Output Dependency REGISTER ADDRESS 32h 33h 34h EEPROM MEMORY ADDRESS 8032h 8033h 8034h BIT OUTPUT ASSERTION CONDITIONS [0] 1 = PO7/PO5 assertion depends on IN1 primary undervoltage threshold (Table 2). [1] 1 = PO7/PO5 assertion depends on IN2 primary undervoltage threshold (Table 3). [2] 1 = PO7/PO5 assertion depends on IN3 primary undervoltage threshold (Table 4). [3] 1 = PO7/PO5 assertion depends on IN4 primary undervoltage threshold (Table 4). [4] 1 = PO7 (MAX6870 only) assertion depends on IN5 primary undervoltage threshold (Table 4). Must be set to 0 for the MAX6871. [5] 1 = PO7 (MAX6870 only) assertion depends on IN6 primary undervoltage threshold (Table 4). Must be set to 0 for the MAX6871. [6] 1 = PO7/PO5 assertion depends on watchdog 1 (Tables 27 and 28). [7] 1 = PO7/PO5 assertion depends on watchdog 2 (Tables 27 and 28). [0] 1 = PO7/PO5 assertion depends on IN1 secondary undervoltage/overvoltage threshold (Table 2). [1] 1 = PO7/PO5 assertion depends on IN2 secondary undervoltage/overvoltage threshold (Table 3). [2] 1 = PO7/PO5 assertion depends on IN3 secondary undervoltage/overvoltage threshold (Table 4). [3] 1 = PO7/PO5 assertion depends on IN4 secondary undervoltage/overvoltage threshold (Table 4). [4] 1 = PO7 (MAX6870 only) assertion depends on IN5 secondary undervoltage/overvoltage threshold (Table 4). Must be set to 0 for the MAX6871. [5] 1 = PO7 (MAX6870 only) assertion depends on IN6 secondary undervoltage/overvoltage threshold (Table 4). Must be set to 0 for the MAX6871. [6] 1 = PO7/PO5 assertion depends on GPI1 (Table 6). [7] 1 = PO7/PO5 assertion depends on GPI2 (Table 6). [0] 1 = PO7/PO5 assertion depends on GPI3 (Table 6). [1] 1 = PO7/PO5 assertion depends on GPI4 (Table 6). [2] 1 = PO7 (MAX6870 only) assertion depends on PO1 (Table 10). Must be set to 0 for the MAX6871. [3] 1 = PO7 (MAX6870 only) assertion depends on PO2 (Table 11). Must be set to 0 for the MAX6871. [4] 1 = PO7/PO5 assertion depends on PO3 (MAX6870)/PO1 (MAX6871) (Tables 12 and 13). [5] 1 = PO7/PO5 assertion depends on PO4 (MAX6870)/PO2 (MAX6871) (Tables 14 and 15). [6] 1 = PO7/PO5 assertion depends on PO5 (MAX6870)/PO3 (MAX6871) (Tables 16 and 17). [7] 1 = PO7/PO5 assertion depends on PO6 (MAX6870)/PO4 (MAX6871) (Tables 18 and 19). 35h 8035h [0] 1 = PO7 (MAX6870 only) assertion depends on PO8 (Table 21). Must be set to 0 for the MAX6871. 40h 8040h [6] 1 = PO7 asserts when MR = low (Table 7). Table 20 only applies to PO7 of the MAX6870 and PO5 of the MAX6871. Write a 0 to a bit to make the PO7/PO5 output independent of the respective signal (IN_ primary 30 or secondary thresholds, WDI1 or WDI2, GPI1–GPI4, MR, or other programmable outputs). ______________________________________________________________________________________ EEPROM-Programmable Hex/Quad Power-Supply Sequencers/Supervisors with ADC REGISTER ADDRESS 36h 37h 38h EEPROM MEMORY ADDRESS 8036h 8037h 8038h BIT MAX6870/MAX6871 Table 21. PO8 (MAX6870 only) Output Dependency OUTPUT ASSERTION CONDITIONS [0] 1 = PO8 assertion depends on IN1 primary undervoltage threshold (Table 2). [1] 1 = PO8 assertion depends on IN2 primary undervoltage threshold (Table 3). [2] 1 = PO8 assertion depends on IN3 primary undervoltage threshold (Table 4). [3] 1 = PO8 assertion depends on IN4 primary undervoltage threshold (Table 4). [4] 1 = PO8 assertion depends on IN5 primary undervoltage threshold (Table 4). [5] 1 = PO8 assertion depends on IN6 primary undervoltage threshold (Table 4). [6] 1 = PO8 assertion depends on watchdog 1 (Tables 27 and 28). [7] 1 = PO8 assertion depends on watchdog 2 (Tables 27 and 28). [0] 1 = PO8 assertion depends on IN1 secondary undervoltage/overvoltage threshold (Table 2). [1] 1 = PO8 assertion depends on IN2 secondary undervoltage/overvoltage threshold (Table 3). [2] 1 = PO8 assertion depends on IN3 secondary undervoltage/overvoltage threshold (Table 4). [3] 1 = PO8 assertion depends on IN4 secondary undervoltage/overvoltage threshold (Table 4). [4] 1 = PO8 assertion depends on IN5 secondary undervoltage/overvoltage threshold (Table 4). [5] 1 = PO8 assertion depends on IN6 secondary undervoltage/overvoltage threshold (Table 4). [6] 1 = PO8 assertion depends on GPI1 (Table 6). [7] 1 = PO8 assertion depends on GPI2 (Table 6). [0] 1 = PO8 assertion depends on GPI3 (Table 6). [1] 1 = PO8 assertion depends on GPI4 (Table 6). [2] 1 = PO8 assertion depends on PO1 (Table 10). [3] 1 = PO8 assertion depends on PO2 (Table 11). [4] 1 = PO8 assertion depends on PO3 (Tables 12 and 13). [5] 1 = PO8 assertion depends on PO4 (Tables 14 and 15). [6] 1 = PO8 assertion depends on PO5 (Tables 16 and 17). [7] 1 = PO8 assertion depends on PO6 (Tables 18 and 19). 39h 8039h [0] 1 = PO8 assertion depends on PO7 (Table 20). 40h 8040h [7] 1 = PO8 asserts when MR = low (Table 7). Table 21 only applies to PO8 of the MAX6870. Write a 0 to a bit to make the PO8 output independent of the respective signal (IN1–IN6 primary or secondary thresholds, WDI1 or WDI2, GPI1–GPI4, MR, or other programmable outputs). Output Stage Configurations Independently program each programmable output as active-high or active-low (Table 22). Additionally, program each programmable output as weak pullup, pushpull, open-drain, or charge pump (Tables 23 and 24). Every programmable output can be configured as open-drain or weak pullup; however, only PO1–PO4 (MAX6870) or PO1/PO2 (MAX6871) can be configured as charge-pump outputs, and only PO5–PO8 (MAX6870) or PO3/PO4/PO5 (MAX6871) can be configured as push-pull outputs. Finally, set the PO_ timeout period for each programmable output (Table 25). An internal 10kΩ resistor provides the pullup resistance for outputs configured as weak pullup stages. Program each weak pullup output stage to refer to ABP or one of the IN3–IN6 inputs. The programmable outputs source up to 10mA and sink up to 4mA when configured as pushpull stages. Program each push-pull output stage to reference to one of IN3–IN6. PO1–PO4 (MAX6870)/ PO1/P02 (MAX6871) pull to VABP + 5V when configured as charge-pump outputs. ______________________________________________________________________________________ 31 MAX6870/MAX6871 EEPROM-Programmable Hex/Quad Power-Supply Sequencers/Supervisors with ADC Table 22. Programmable Output Active States REGISTER ADDRESS 3Ah EEPROM MEMORY ADDRESS 803Ah BIT RANGE DESCRIPTION [0] PO1 (MAX6870 only). 0 = active-low, 1 = active-high. [1] PO2 (MAX6870 only). 0 = active-low, 1 = active-high. [2] PO3 (MAX6870)/PO1 (MAX6871). 0 = active-low, 1 = active-high. [3] PO4 (MAX6870)/PO2 (MAX6871). 0 = active-low, 1 = active-high. [4] PO5 (MAX6870)/PO3 (MAX6871). 0 = active-low, 1 = active-high. [5] PO6 (MAX6870)/PO4 (MAX6871). 0 = active-low, 1 = active-high. [6] PO7 (MAX6870)/PO5 (MAX6871). 0 = active-low, 1 = active-high. [7] PO8 (MAX6870 only). 0 = active-low, 1 = active-high. Table 23. Programmable Output Stage Options (MAX6870) REGISTER ADDRESS EEPROM MEMORY ADDRESS BIT RANGE AFFECTED OUTPUT 11h 8011h [6:4] PO1 15h 8015h [6:4] PO2 1Ch 801Ch [7:5] PO3 PO4 23h 8023h [7:5] 2Ah 802Ah [7:4] PO5 31h 8031h [7:4] PO6 35h 8035h [7:4] PO7 39h 8039h [7:4] PO8 DESCRIPTION 000 = open-drain, 001 = weak pullup to IN3, 010 = weak pullup to IN4, 011 = weak pullup to IN5, 100 = weak pullup to IN6, 101 = weak pullup to ABP, 110 = charge-pump output, 111 = not used. 0000 = open-drain, 0001 = weak pullup to IN3, 0010 = weak pullup to IN4, 0011 = weak pullup to IN5, 0100 = weak pullup to IN6, 0101 = weak pullup to ABP, 0110 = push-pull to IN3, 0111 = push-pull to IN4, 1000 = push-pull to IN5, 1001 = push-pull to IN6, 1010 through 1111 = not used. Table 24. Programmable Output Stage Options (MAX6871) REGISTER ADDRESS EEPROM MEMORY ADDRESS BIT RANGE AFFECTED OUTPUT 1Ch 801Ch [7:5] PO1 23h 8023h [7:5] PO2 2Ah 802Ah [7:4] PO3 31h 8031h [7:4] PO4 35h 8035h [7:4] PO5 32 DESCRIPTION 000 = open-drain, 001 = weak pullup to IN3, 010 = weak pullup to IN4, 011–100 = not used, 101 = weak pullup to ABP, 110 = charge-pump output, 111 = not used. 0000 = open-drain, 0001 = weak pullup to IN3, 0010 = weak pullup to IN4, 0011–0100 = not used, 0101 = weak pullup to ABP, 0110 = push-pull to IN3, 0111 = push-pull to IN4, 1000–1111 = not used. ______________________________________________________________________________________ EEPROM-Programmable Hex/Quad Power-Supply Sequencers/Supervisors with ADC REGISTER ADDRESS EEPROM MEMORY ADDRESS BIT RANGE 11h 8011h 15h 8015h 1Ch AFFECTED OUTPUTS DESCRIPTION MAX6870 MAX6871 [3:1] PO1 — [3:1] PO2 — 801Ch [4:2] PO3 PO1 PO2 23h 8023h [4:2] PO4 2Ah 802Ah [3:1] PO5 PO3 31h 8031h [3:1] PO6 PO4 35h 8035h [3:1] PO7 PO5 39h 8039h [3:1] PO8 — Charge-Pump Output Configuration Configure the programmable outputs of the MAX6870/ MAX6871 as charge-pump outputs to drive n-channel FETs for power-supply sequencing applications. Only PO1–PO4 (MAX6870) or PO1 and PO2 (MAX6871) can be configured as charge-pump output stages. The chargepump output high voltage is typically V ABP +5.5V when unloaded. Push-Pull Output Configuration The MAX6870/MAX6871’s programmable outputs sink 4mA and source 10mA when configured as push-pull outputs. Only PO5–PO8 (MAX6870), or PO3/PO4/PO5 (MAX6871) can be configured as push-pull output stages. The push-pull output stages refer to any of IN3–IN6 (MAX6870)/IN3/IN4 (MAX6871) as configured in Tables 23 and 24. Use the push-pull output configuration to drive loads with fast rise/fall times, or those with low impedance. Weak Pullup Output Configuration The MAX6870/MAX6871’s programmable outputs sink 4mA when configured as weak pullups. The weak pullup of 10kΩ refers to any of IN3–IN6 (MAX6870)/IN3/IN4 (MAX6871) or ABP as configured in Tables 23 and 24. All programmable outputs of the MAX6870/MAX6871 may be configured as weak pullups. Open-Drain Output Configuration Connect an external pullup resistor from the programmable output to an external voltage when configured as an open-drain output. PO1–PO4 (PO1 and PO2 for the MAX6871) may be pulled up to +13.2V. PO5–PO8 (PO3–PO5 for the MAX6871) may be pulled up to a voltage less than or equal to ABP. Choose the pullup resistor depending on the number of devices connected to the open-drain output and the allowable current consumption. The open-drain output configuration 000 = 25µs 001 = 1.5625ms 010 = 6.25ms 011 = 25ms 100 = 50ms 101 = 200ms 110 = 400ms 111 = 1600ms allows wire-ORed connections, and provides flexibility in setting the pullup current. Configuring the MAX6870/MAX6871 The MAX6870/MAX6871 factory-default configuration sets all registers to 00h except 3Ah, which is set to FFh. Each device requires configuration before full power is applied to the system. To configure the MAX6870/ MAX6871, first apply an input voltage to IN1 or one of IN3–IN6 (MAX6870)/IN3/IN4 (MAX6871) (see the Powering the MAX6870/MAX6871 section). VIN1 > +4V or one of VIN3–VIN6 > +2.7V, to ensure device operation. Next, transmit data through the serial interface. Use the block write protocol to quickly configure the device. Write to the configuration registers first to ensure the device is configured properly. After completing the setup procedure, use the read word protocol to verify the data from the configuration registers. Lastly, use the write word protocol to write this data to the EEPROM registers. After completing EEPROM register configuration, apply full power to the system to begin normal operation. The nonvolatile EEPROM stores the latest configuration upon removal of power. Write 0’s to all EEPROM registers to clear the memory. Software Reboot A software reboot allows the user to restore the EEPROM configuration to the volatile registers without cycling the power supplies. Use the send byte command with data byte 88h to initiate a software reboot. The 3.5ms (max) power-up delay also applies after a software reboot. SMBus/I2C-Compatible Serial Interface The MAX6870/MAX6871 feature an I2C/SMBus-compatible serial interface consisting of a serial data line (SDA) and a serial clock line (SCL). SDA and SCL allow bidirectional communication between the MAX6870/MAX6871 ______________________________________________________________________________________ 33 MAX6870/MAX6871 Table 25. PO_ Timeout Periods MAX6870/MAX6871 EEPROM-Programmable Hex/Quad Power-Supply Sequencers/Supervisors with ADC and the master device at clock rates up to 400kHz. Figure 2 shows the interface timing diagram. The MAX6870/MAX6871 are transmit/receive slave-only devices, relying upon a master device to generate a clock signal. The master device (typically a microcontroller) initiates data transfer on the bus and generates SCL to permit that transfer. resistors to generate the logic-high voltage. Use 4.7kΩ for most applications. Bit Transfer Each clock pulse transfers one data bit. The data on SDA must remain stable while SCL is high (Figure 3), otherwise the MAX6870/MAX6871 register a START or STOP condition (Figure 4) from the master. SDA and SCL idle high when the bus is not busy. A master device communicates to the MAX6870/ MAX6871 by transmitting the proper address followed by command and/or data words. Each transmit sequence is framed by a START (S) or REPEATED START (SR) condition and a STOP (P) condition. Each word transmitted over the bus is 8 bits long and is always followed by an acknowledge pulse. SCL is a logic input, while SDA is a logic input/opendrain output. SCL and SDA both require external pullup Start and Stop Conditions Both SCL and SDA idle high when the bus is not busy. A master device signals the beginning of a transmission with a START (S) condition (Figure 4) by transitioning SDA from high to low while SCL is high. The master device issues a STOP (P) condition (Figure 4) by transitioning SDA from low to high while SCL is high. A STOP SDA tBUF tSU:DAT tSU:STA tHD:DAT tLOW tHD:STA tSU:STO SCL tHIGH tHD:STA tR tF START CONDITION STOP CONDITION REPEATED START CONDITION START CONDITION Figure 2. Serial-Interface Timing Details SDA SDA SCL SCL DATA LINE STABLE, CHANGE OF DATA ALLOWED DATA VALID Figure 3. Bit Transfer 34 S P START CONDITION STOP CONDITION Figure 4. Start and Stop Conditions ______________________________________________________________________________________ EEPROM-Programmable Hex/Quad Power-Supply Sequencers/Supervisors with ADC an ACK. The MAX6870/MAX6871 generate an ACK when receiving an address or data by pulling SDA low during the 9th clock period (Figure 5). When transmitting data, such as when the master device reads data back from the MAX6870/MAX6871, the MAX6870/MAX6871 wait for the master device to generate an ACK. Monitoring ACK allows for detection of unsuccessful data transfers. An unsuccessful data transfer occurs if the receiving device is busy or if a system fault has occurred. In the event of an unsuccessful data transfer, the bus master should reattempt communication at a later time. The MAX6870/MAX6871 generate a NACK after the slave address during a software reboot, while writing to the EEPROM, or when receiving an illegal memory address. Early STOP Conditions The MAX6870/MAX6871 recognize a STOP condition at any point during transmission except if a STOP condition occurs in the same high pulse as a START condition. This condition is not a legal I2C format. At least one clock pulse must separate any START and STOP condition. Repeated START Conditions A REPEATED START (SR) condition may indicate a change of data direction on the bus. Such a change occurs when a command word is required to initiate a read operation (see Figure 7). SR may also be used when the bus master is writing to several I2C devices and does not want to relinquish control of the bus. The MAX6870/MAX6871 serial interface supports continuous write operations with or without an SR condition separating them. Continuous read operations require SR conditions because of the change in direction of data flow. Slave Address The MAX6870/MAX6871 slave address conforms to the following table: Acknowledge The acknowledge bit (ACK) is the 9th bit attached to any 8-bit data word. The receiving device always generates SA7 (MSB) SA6 SA5 SA4 SA3 SA2 SA1 SA0 (LSB) 1 0 1 0 A1 A0 X R/W X = Don’t care. START CONDITION CLOCK PULSE FOR ACKNOWLEDGE 1 SCL 2 8 9 SDA BY TRANSMITTER S SDA BY RECEIVER Figure 5. Acknowledge ______________________________________________________________________________________ 35 MAX6870/MAX6871 condition frees the bus for another transmission. The bus remains active if a REPEATED START condition is generated, such as in the block read protocol (see Figure 7). MAX6870/MAX6871 EEPROM-Programmable Hex/Quad Power-Supply Sequencers/Supervisors with ADC SA7 through SA4 represent the standard interface address (1010) for devices with EEPROM. SA3 and SA2 correspond to the A1 and A0 address inputs of the MAX6870/MAX6871 (hard-wired as logic-low or logichigh). SA0 is a read/write flag bit (0 = write, 1 = read). The A0 and A1 address inputs allow up to four MAX6870/MAX6871 devices to connect to one bus. Connect A0 and A1 to GND or to the serial interface power supply (see Figure 6). Send Byte The send byte protocol allows the master device to send one byte of data to the slave device (see Figure 7). The send byte presets a register pointer address for a subsequent read or write. The slave sends a NACK instead of an ACK if the master tries to send an address that is not allowed. If the master sends 80h, 81h, or 82h, the data is ACK. This could be start of the write byte/word protocol, and the slave expects at least one further data byte. If the master sends a stop condition, the internal address pointer does not change. If the master sends 84h, this signifies that the block read protocol is expected, and a repeated start condition should follow. The device reboots if the master sends 88h. The send byte procedure follows: 1) The master sends a start condition. 2) The master sends the 7-bit slave address and a write bit (low). 3) The addressed slave asserts an ACK on SDA. 4) The master sends an 8-bit data byte. 5) The addressed slave asserts an ACK on SDA. 6) The master sends a stop condition. SDA START 1 MSB 0 1 0 Write Byte/Word The write byte/word protocol allows the master device to write a single byte in the register bank, preset an EEPROM (configuration or user) address for a subsequent read, or to write a single byte to the configuration or user EEPROM (see Figure 7). The write byte/word procedure follows: 1) The master sends a start condition. 2) The master sends the 7-bit slave address and a write bit (low). 3) The addressed slave asserts an ACK on SDA. 4) The master sends an 8-bit command code. 5) The addressed slave asserts an ACK on SDA. 6) The master sends an 8-bit data byte. 7) The addressed slave asserts an ACK on SDA. 8) The master sends a stop condition or sends another 8-bit data byte. 9) The addressed slave asserts an ACK on SDA. 10) The master sends a stop condition. To write a single byte to the register bank, only the 8-bit command code and a single 8-bit data byte are sent. The command code must be in the range of 00h to 45h. The data byte is written to the register bank if the command code is valid. The slave generates a NACK at step 5 if the command code is invalid. To preset an EEPROM (configuration or user) address for a subsequent read, the 8-bit command code and a single 8-bit data byte are sent. The command code must be 80h if the write is to be directed into the configuration EEPROM, or 81h or 82h, if the write is to be A1 A0 X R/W LSB SCL Figure 6. Slave Address 36 ______________________________________________________________________________________ ACK EEPROM-Programmable Hex/Quad Power-Supply Sequencers/Supervisors with ADC S ADDRESS WR 7 bits 0 ACK DATA ACK S P 8 bits Slave Address– equivalent to chipselect line of a 3wire interface. Data Byte–presets the internal address pointer. ACK DATA 1 7 bits WR 7 bits 0 ACK COMMAND ACK DATA 8 bits ACK DATA 8 bits Command Byte– MSB of the EEPROM register being written. ACK P 8 bits Data Byte–first byte is the LSB of the EEPROM address. Second byte is the actual data. WRITE BYTE FORMAT WR ADDRESS ADDRESS Slave Address– equivalent to chipselect line of a 3wire interface. RECEIVE BYTE FORMAT S MAX6870/MAX6871 WRITE WORD FORMAT SEND BYTE FORMAT ACK S P 8 bits Slave Address– equivalent to chipselect line of a 3wire interface. Data Byte–reads data from the register commanded by the last read byte or write byte transmission. Also dependent on a send byte. ADDRESS WR 7 bits 0 ACK COMMAND ACK 8 bits Slave Address– equivalent to chipselect line of a 3wire interface. DATA ACK P 8 bits Command Byte– selects register being written. Data Byte–data goes into the register set by the command byte if the command is below 50h. If the command is 80h, 81h, or 82h, the data byte presets the LSB of an EEPROM address. BLOCK WRITE FORMAT S ADDRESS WR ACK 0 7 bits BYTE COUNT= N COMMAND ACK DATA BYTE 1 8 bits 8 bits Slave Address– equivalent to chipselect line of a 3wire interface. ACK ACK DATA BYTE ... 8 bits Command Byte– prepares device for block operation. ACK 8 bits DATA BYTE N ACK P 8 bits Data Byte–data goes into the register set by the command byte. BLOCK READ FORMAT S ADDRESS WR 7 bits 0 Slave Address– equivalent to chipselect line of a 3wire interface. S = Start condition. P = Stop condition. ACK COMMAND ACK SR 8 bits Command Byte– prepares device for block operation. ADDRESS WR 7 bits 1 Slave Address– equivalent to chipselect line of a 3wire interface. ACK BYTE COUNT= 16 10h ACK DATA BYTE ACK 1 8 bits DATA BYTE ACK ... 8 bits DATA BYTE ACK N P 8 bits Data Byte–data goes into the register set by the command byte. Shaded = Slave transmission. SR = Repeated start condition. Figure 7. SMBus/I2C Protocols ______________________________________________________________________________________ 37 MAX6870/MAX6871 EEPROM-Programmable Hex/Quad Power-Supply Sequencers/Supervisors with ADC directed into the user EEPROM. If the command code is 80h, the data byte must be in the range of 00h to 45h. If the command code is 81h or 82h, the data byte can be 00h to FFh. A NACK is generated in step 7 if none of the above conditions are true. To write a single byte of data to the user or configuration EEPROM, the 8-bit command code and a single 8-bit data byte are sent. The following 8-bit data byte is written to the addressed EEPROM location. Block Write The block write protocol allows the master device to write a block of data (1 to 16 bytes) to the EEPROM or to the register bank (see Figure 7). The destination address must already be set by the send byte or write byte protocol and the command code must be 83h. If the number of bytes to be written causes the address pointer to exceed 45h for the configuration register or configuration EEPROM, the address pointer stays at 45h, overwriting this memory address with the remaining bytes of data. The last data byte sent is stored at register address 45h. If the number of bytes to be written exceeds the address pointer FFh for the user EEPROM, the address pointer loops back to 00h, and continues writing bytes until all data is written. The block write procedure follows: 1) The master sends a start condition. 2) The master sends the 7-bit slave address and a write bit (low). 3) The addressed slave asserts an ACK on SDA. 4) The master sends the 8-bit command code for block write (83h). 5) The addressed slave asserts an ACK on SDA. 6) The master sends the 8-bit byte count (1 to 16 bytes) N. 7) The addressed slave asserts an ACK on SDA. 8) The master sends 8-bits of data. the contents of the next address. The receive byte procedure follows: 1) The master sends a start condition. 2) The master sends the 7-bit slave address and a read bit (high). 3) The addressed slave asserts an ACK on SDA. 4) The slave sends 8 data bits. 5) The master asserts a NACK on SDA. 6) The master generates a stop condition. Block Read The block read protocol allows the master device to read a block of 16 bytes from the EEPROM or register bank (see Figure 7). Read fewer than 16 bytes of data by issuing an early STOP condition from the master, or by generating a NACK with the master. The send byte or write byte protocol predetermines the destination address with a command code of 84h. The block read procedure follows: 1) The master sends a start condition. 2) The master sends the 7-bit slave address and a write bit (low). 3) The addressed slave asserts an ACK on SDA. 4) The master sends 8 bits of the block read command (84h). 5) The slave asserts an ACK on SDA, unless busy. 6) The master generates a repeated start condition. 7) The master sends the 7-bit slave address and a read bit (high). 8) The slave asserts an ACK on SDA. 9) The slave sends the 8-bit byte count (16). 10) The master asserts an ACK on SDA. 11) The slave sends 8 bits of data. 11) The master generates a stop condition. 12) The master asserts an ACK on SDA. 13) Repeat steps 8 and 9 fifteen times. 14) The master generates a stop condition. Receive Byte The receive byte protocol allows the master device to read the register content of the MAX6870/MAX6871 (see Figure 7). The EEPROM or register address must be preset with a send byte or write word protocol first. Once the read is complete, the internal pointer increases by one. Repeating the receive byte protocol reads Address Pointers Use the send byte protocol to set the register address pointers before read and write operations. For the configuration registers, valid address pointers range from 00h to 45h. Register addresses outside of this range result in a NACK being issued from the MAX6870/ MAX6871. When using the block write protocol, the 9) The addressed slave asserts an ACK on SDA. 10) Repeat steps 8 and 9 one time. 38 ______________________________________________________________________________________ EEPROM-Programmable Hex/Quad Power-Supply Sequencers/Supervisors with ADC For the user EEPROM, valid address pointers range from 8100h to 81FFh and 8200h to 82FFh. Block write and block read protocols allow the address pointer to reset (to 8100h or 8200h) when attempting to write or read beyond 81FFh or 82FFh. Configuration EEPROM The configuration EEPROM addresses range from 8000h to 8045h. Write data to the configuration EEPROM to automatically set up the MAX6870/MAX6871 upon powerup. Data transfers from the configuration EEPROM to the configuration registers when ABP exceeds UVLO during power-up or after a software reboot. After ABP exceeds UVLO, an internal 1MHz clock starts after a 5µs delay, and data transfer begins. Data transfer disables access to the configuration registers and EEPROM. The data transfer from EEPROM to configuration registers takes 3.5ms (max). Read configuration EEPROM data at any time after power-up or software reboot. Write commands to the configuration EEPROM are allowed at any time after power-up or software reboot, unless the configuration lock bit is set (see Table 30). The maximum cycle time to write a single byte is 11ms (max). User EEPROM The 512 byte user EEPROM addresses range from 8100h to 82FFh (see Figure 8). Store software-revision data, board-revision data, and other data in these registers. The maximum cycle time to write a single byte is 11ms (max). Configuration Register Bank and EEPROM The configuration registers can be directly modified by the serial interface without modifying the EEPROM after the power-up procedure terminates and the configuration EEPROM data has been loaded into the configuration register bank. Use the write byte or block write protocols to write directly to the configuration registers. Changes to the configuration registers take effect immediately and are lost upon power removal. At device power-up, the register bank loads configuration data from the EEPROM. Configuration data may be directly altered in the register bank during application development, allowing maximum flexibility. Transfer the new configuration data, byte by byte, to the configuration EEPROM with the write byte protocol. The next device power-up or software reboot automatically loads the new configuration. Table 26. Register Map REGISTER ADDRESS EEPROM MEMORY ADDRESS READ/ WRITE 00h 8000h R/W IN1 primary undervoltage detector threshold (Table 2). 01h 8001h R/W IN2 primary undervoltage detector threshold (Table 3). 02h 8002h R/W IN3 primary undervoltage detector threshold (Table 4). 03h 8003h R/W IN4 primary undervoltage detector threshold (Table 4). 04h 8004h R/W IN5 primary undervoltage detector threshold (MAX6870 only) (Table 4). 05h 8005h R/W IN6 primary undervoltage detector threshold (MAX6870 only) (Table 4). 06h 8006h R/W IN1 secondary undervoltage/overvoltage detector threshold (Table 2). 07h 8007h R/W IN2 secondary undervoltage/overvoltage detector threshold (Table 3). 08h 8008h R/W IN3 secondary undervoltage/overvoltage detector threshold (Table 4). 09h 8009h R/W IN4 secondary undervoltage/overvoltage detector threshold (Table 4). 0Ah 800Ah R/W IN5 secondary undervoltage/overvoltage detector threshold (MAX6870 only) (Table 4). DESCRIPTION ______________________________________________________________________________________ 39 MAX6870/MAX6871 address pointer automatically increments after each data byte, except when the address pointer is already at 45h. If the address pointer is already 45h, and more data bytes are being sent, these subsequent bytes overwrite address 45h repeatedly, leaving only the last data byte sent stored at this register address. For the configuration EEPROM, valid address pointers range from 8000h to 8045h. Registers 8046h to 804Fh are reserved and should not be overwritten. Register addresses from 8050h to 80FFh return a NACK from the MAX6870/MAX6871. When using the block write protocol, the address pointer automatically increments after each data byte, except when the address pointer is already at 8045h. If the address pointer is already 8045h, and more data bytes are being sent, these subsequent bytes overwrite address 8045h repeatedly, leaving only the last data byte sent stored at this register address. MAX6870/MAX6871 EEPROM-Programmable Hex/Quad Power-Supply Sequencers/Supervisors with ADC Table 26. Register Map (continued) REGISTER ADDRESS EEPROM MEMORY ADDRESS READ/ WRITE 0Bh 800Bh R/W IN6 secondary undervoltage/overvoltage detector threshold (MAX6870 only) (Table 4). 0Ch 800Ch R/W Secondary undervoltage/overvoltage selection (Tables 2, 4). 0Dh 800Dh R/W Threshold range selection (Tables 2–4). 0Eh 800Eh R/W PO1 (MAX6870 only) input selection (Table 10). 0Fh 800Fh R/W PO1 (MAX6870 only) input selection (Table 10). 10h 8010h R/W PO1 (MAX6870 only) input selection (Table 10). 11h 8011h R/W PO1 (MAX6870 only) input selection, PO_ timeout period, and output type selection (Tables 10, 23, and 25). 12h 8012h R/W PO2 (MAX6870 only) input selection (Table 11). 13h 8013h R/W PO2 (MAX6870 only) input selection (Table 11). 14h 8014h R/W PO2 (MAX6870 only) input selection (Table 11). 15h 8015h R/W PO2 (MAX6870 only) input selection, PO_ timeout period, and output type selection (Tables 11, 23, and 25). 16h 8016h R/W PO3 (MAX6870)/PO1 (MAX6871) input selection—Product 1 (Table 12). 17h 8017h R/W PO3 (MAX6870)/PO1 (MAX6871) input selection—Product 1 (Table 12). 18h 8018h R/W PO3 (MAX6870)/PO1 (MAX6871) input selection—Product 1 (Table 12). 19h 8019h R/W PO3 (MAX6870)/PO1 (MAX6871) input selection—Product 2 (Table 13). 1Ah 801Ah R/W PO3 (MAX6870)/PO1 (MAX6871) input selection—Product 2 (Table 13). 1Bh 801Bh R/W PO3 (MAX6870)/PO1 (MAX6871) input selection—Product 2 (Table 13). 40 DESCRIPTION 1Ch 801Ch R/W PO3 (MAX6870)/PO1 (MAX6871) input selection—Products 1 and 2, PO_ timeout period, and output type selection (Tables 12, 13, 23, 24, and 25). 1Dh 801Dh R/W PO4 (MAX6870)/PO2 (MAX6871) input selection—Product 1 (Table 14). 1Eh 801Eh R/W PO4 (MAX6870)/PO2 (MAX6871) input selection—Product 1 (Table 14). 1Fh 801Fh R/W PO4 (MAX6870)/PO2 (MAX6871) input selection—Product 1 (Table 14). 20h 8020h R/W PO4 (MAX6870)/PO2 (MAX6871) input selection—Product 2 (Table 15). 21h 8021h R/W PO4 (MAX6870)/PO2 (MAX6871) input selection—Product 2 (Table 15). 22h 8022h R/W PO4 (MAX6870)/PO2 (MAX6871) input selection—Product 2 (Table 15). 23h 8023h R/W PO4 (MAX6870)/PO2 (MAX6871) input selection—Products 1 and 2, PO_ timeout period, and output type selection (Tables 14, 15, 23, 24, and 25). 24h 8024h R/W PO5 (MAX6870)/PO3 (MAX6871) input selection—Product 1 (Table 16). 25h 8025h R/W PO5 (MAX6870)/PO3 (MAX6871) input selection—Product 1 (Table 16). 26h 8026h R/W PO5 (MAX6870)/PO3 (MAX6871) input selection—Product 1 (Table 16). 27h 8027h R/W PO5 (MAX6870)/PO3 (MAX6871) input selection—Product 2 (Table 17). 28h 8028h R/W PO5 (MAX6870)/PO3 (MAX6871) input selection—Product 2 (Table 17). 29h 8029h R/W PO5 (MAX6870)/PO3 (MAX6871) input selection—Product 2 (Table 17). 2Ah 802Ah R/W PO5 (MAX6870)/PO3 (MAX6871) input selection—Products 1 and 2, PO_ timeout period, and output type selection (Tables 16, 23, 24, and 25). 2Bh 802Bh R/W PO6 (MAX6870)/PO4 (MAX6871) input selection—Product 1 (Table 18). 2Ch 802Ch R/W PO6 (MAX6870)/PO4 (MAX6871) input selection—Product 1 (Table 18). ______________________________________________________________________________________ EEPROM-Programmable Hex/Quad Power-Supply Sequencers/Supervisors with ADC REGISTER ADDRESS EEPROM MEMORY ADDRESS READ/ WRITE 2Dh 802Dh R/W 2Eh 802Eh R/W PO6 (MAX6870)/PO4 (MAX6871) input selection—Product 2 (Table 19). 2Fh 802Fh R/W PO6 (MAX6870)/PO4 (MAX6871) input selection—Product 2 (Table 19). 30h 8030h R/W PO6 (MAX6870)/PO4 (MAX6871) input selection—Product 2 (Table 19). MAX6870/MAX6871 Table 26. Register Map (continued) DESCRIPTION PO6 (MAX6870)/PO4 (MAX6871) input selection—Product 1 (Table 18). 31h 8031h R/W PO6 (MAX6870)/PO4 (MAX6871) input selection—Products 1 and 2, reset timeout period, and output type selection (Tables 18, 23, 24, and 25). 32h 8032h R/W PO7 (MAX6870)/PO5 (MAX6871) input selection (Table 20). 33h 8033h R/W PO7 (MAX6870)/PO5 (MAX6871) input selection (Table 20). 34h 8034h R/W PO7 (MAX6870)/PO5 (MAX6871) input selection (Table 20). 35h 8035h R/W PO7 (MAX6870)/PO5 (MAX6871) input selection, PO_ timeout period, and output type selection (Tables 20, 23, 24, and 25). 36h 8036h R/W PO8 (MAX6870 only) input selection (Table 21). 37h 8037h R/W PO8 (MAX6870 only) input selection (Table 21). 38h 8038h R/W PO8 (MAX6870 only) input selection (Table 21). 39h 8039h R/W PO8 (MAX6870 only) input selection, PO_ timeout period, and output type selection. (Tables 21, 23, 24, and 25). 3Ah 803Ah R/W Programmable output polarity (active-high/active-low) (Table 22). 3Bh 803Bh R/W GPI_ input polarity, PO5, PO6 (Tables 6, 17, and 19). 3Ch 803Ch R/W WDI1 input selection and timeout enable (Table 27). 3Dh 803Dh R/W WDI1 initial and normal timeout duration (Table 28). 3Eh 803Eh R/W WDI2 input selection and timeout enable (Table 27). 3Fh 803Fh R/W WDI2 initial and normal timeout duration (Table 28). 40h 8040h R/W MR input and programmable output behavior (Table 7). 41h 8041h R/W MARGIN and programmable output behavior (Table 8). 42h 8042h R/W Programmable output state with MARGIN assertion (Table 8). 43h 8043h R/W User EEPROM write disable (Table 31). 44h 8044h R/W Internal/external reference selection (Table 9). 45h 8045h R/W 46h 8046h — Reserved. Should not be overwritten. 47h 8047h — Reserved. Should not be overwritten. 48h 8048h — Reserved. Should not be overwritten. 49h 8049h — Reserved. Should not be overwritten. 4Ah 804Ah — Reserved. Should not be overwritten. 4Bh 804Bh — Reserved. Should not be overwritten. 4Ch 804Ch — Reserved. Should not be overwritten. 4Dh 804Dh — Reserved. Should not be overwritten. 4Eh 804Eh — Reserved. Should not be overwritten. 4Fh 804Fh — Reserved. Should not be overwritten. Configuration lock (Table 30). ______________________________________________________________________________________ 41 MAX6870/MAX6871 EEPROM-Programmable Hex/Quad Power-Supply Sequencers/Supervisors with ADC Table 26. Register Map (continued) REGISTER ADDRESS EEPROM MEMORY ADDRESS READ/ WRITE 50h — R ADC data for IN1 (8 MSBs). 51h — R ADC data for IN1 (2 LSBs). 52h — R ADC data for IN2 (8 MSBs). 53h — R ADC data for IN2 (2 LSBs). 54h — R ADC data for IN3 (8 MSBs). 55h — R ADC data for IN3 (2 LSBs). 56h — R ADC data for IN4 (8 MSBs). 57h — R ADC data for IN4 (2 LSBs). 58h — R ADC data for IN5 (8 MSBs, MAX6870 only). 59h — R ADC data for IN5 (2 LSBs, MAX6870 only). 5Ah — R ADC data for IN6 (8 MSBs, MAX6870 only). 5Bh — R ADC data for IN6 (2 LSBs, MAX6870 only). 5Ch — R ADC data for AUXIN1 (8 MSBs) (Table 5). DESCRIPTION 5Dh — R ADC data for AUXIN1 (2 LSBs) (Table 5). 5Eh — R ADC data for AUXIN2 (8 MSBs) (Table 5). 5Fh — R ADC data for AUXIN2 (2 LSBs) (Table 5). 60h — R Fault flags for IN1–IN6 (primary thresholds) (Table 29). 61h — R Fault flags for IN1–IN6 (secondary thresholds) (Table 29). 62h — R Fault flags for WDI_, GPI_, and MR (Table 29). CONFIGURATION EEPROM REGISTER BANK 8000h 00h USER EEPROM USER EEPROM 8100h 8200h 81FFh 82FFh CONFIGURATION DATA 45h 50h 62h 8045h RESERVED ADC AND FAULT REGISTERS (READ ONLY) Figure 8. Memory Map 42 ______________________________________________________________________________________ EEPROM-Programmable Hex/Quad Power-Supply Sequencers/Supervisors with ADC Table 27. Watchdog Inputs (Addresses 3Ch (Watchdog 1), 3Eh (Watchdog 2)) BIT [1:0] [4:2] NAME DESCRIPTION Watchdog Input Selection 00 = GPI1 input 01 = GPI2 input 10 = GPI3 input 11 = GPI4 input Watchdog Internal Input Selection 000 = PO1 (MAX6870), not used (MAX6871) 001 = PO2 (MAX6870), not used (MAX6871) 010 = PO3 (MAX6870), PO1 (MAX6871) 011 = PO4 (MAX6870), PO2 (MAX6871) 100 = PO5 (MAX6870), PO3 (MAX6871) 101 = PO6 (MAX6870), PO4 (MAX6871) 110 = PO7 (MAX6870), PO5 (MAX6871) 111 = PO8 (MAX6870), not used (MAX6871) 00 = 11 = watchdog clear depends on both GPI_ from 3Ch[1:0] and PO_ from Watchdog 3Ch[4:2]. [6:5] Dependency 01 = watchdog clear depends only on PO_ from 3Ch[4:2]. on Inputs 10 = watchdog clear depends only on GPI_ from 3Ch[1:0]. [7] Initial Watchdog Timeout Enable 0 = disables initial watchdog timeout period (normal watchdog timeout not affected). 1 = enables initial watchdog timeout period. perform its initialization process. If no pulse occurs during the initial watchdog timeout period, the µP is taking too long to initialize, indicating a potential problem. The normal watchdog timeout period applies in every other cycle after the initial watchdog timeout period occurs. The normal watchdog timeout period monitors a pulsed output of the µP that indicates when normal processor behavior occurs. If no pulse occurs during the normal watchdog timeout period, this indicates that the processor has stopped operating or is stuck in an infinite execution loop. Disable or enable each initial timeout period through registers 3Ch and 3Eh. Registers 3Dh and 3Fh program the initial and normal watchdog timeout periods, and enable or disable each watchdog timer. See Tables 27 and 28 for a summary of the watchdog behavior. Fault Detector Registers 60h–62h store all fault conditions, including undervoltage, overvoltage, GPI_, and watchdog timer faults (see Table 29). Fault registers are read-only and lose contents upon power removal. The first read command from the fault registers after power-up gives invalid data. Any MR assertion writes to the fault register. Reading the fault register clears all fault flags. Both GPI_ Table 28. Watchdog Timeout Period Selection (Addresses 3Dh (Watchdog 1), 3Fh (Watchdog 2)) BIT NAME DESCRIPTION [2:0] Normal Watchdog Timeout Period 000 = 6.25ms 001 = 25ms 010 = 100ms 011 = 400ms 100 = 1.6s 101 = 6.4s 110 = 25.6s 111 = 102.4s [5:3] Initial Watchdog Timeout Period (Immediately following powerup, reset event, or enabling watchdog) 000 = 6.25ms 001 = 25ms 010 = 100ms 011 = 400ms 100 = 1.6s 101 = 6.4s 110 = 25.6s 111 = 102.4s [6] Watchdog Enable [7] — 0 = disables watchdog timer 1 = enables watchdog timer Not used ______________________________________________________________________________________ 43 MAX6870/MAX6871 Configuring the Watchdog Timers (Registers 3Ch–3Fh) A watchdog timer monitors microprocessor (µP) software execution for a stalled condition and resets the µP if it stalls. The output of a watchdog timer (one of the programmable outputs) connects to the reset input or a nonmaskable interrupt of the µP. Registers 3Ch–3Fh configure the watchdog functionality of the MAX6870/MAX6871. Program each watchdog timer to assert one or more programmable outputs (see Tables 10–21). Program each watchdog timer to reset on one of the GPI_ inputs, one of the programmable outputs, or a combination of one GPI_ input and one programmable output. Each watchdog timer features independent initial and normal watchdog timeout periods. The initial watchdog timeout period applies immediately after power-up, after a reset event takes place, or after enabling the watchdog timer. The initial watchdog timeout period allows the µP to MAX6870/MAX6871 EEPROM-Programmable Hex/Quad Power-Supply Sequencers/Supervisors with ADC Table 29. Fault Registers (60h–62h) REGISTER ADDRESS 60h BIT RANGE [0] 1 = IN1 falls below primary undervoltage threshold. [1] 1 = IN2 falls below primary undervoltage threshold. [2] 1 = IN3 falls below primary undervoltage threshold. [3] 1 = IN4 falls below primary undervoltage threshold. [4] 1 = IN5 (MAX6870 only) falls below primary undervoltage threshold. [5] 1 = IN6 (MAX6870 only) falls below primary undervoltage threshold. [7:6] 61h Not used. [0] 1 = IN1 falls below secondary undervoltage threshold or rises above secondary overvoltage threshold, depending on the settings in register 0Ch (see Tables 2, 3, and 4). [1] 1 = IN2 falls below secondary undervoltage threshold or rises above secondary overvoltage threshold, depending on the settings in register 0Ch (see Tables 2, 3, and 4). [2] 1 = IN3 falls below secondary undervoltage threshold or rises above secondary overvoltage threshold, depending on the settings in register 0Ch (see Tables 2, 3, and 4). [3] 1 = IN4 falls below secondary undervoltage threshold or rises above secondary overvoltage threshold, depending on the settings in register 0Ch (see Tables 2, 3, and 4). [4] 1 = IN5 (MAX6870 only) falls below secondary undervoltage threshold or rises above secondary overvoltage threshold, depending on the settings in register 0Ch (see Tables 2, 3, and 4). [5] 1 = IN6 (MAX6870 only) falls below secondary undervoltage threshold or rises above secondary overvoltage threshold, depending on the settings in register 0Ch (see Tables 2, 3, and 4). [7:6] 62h DESCRIPTION Not used. [0] 1 = WDI1 asserted. [1] 1 = WDI2 asserted. [2] 1 = GPI1 asserted. [3] 1 = GPI2 asserted. [4] 1 = GPI3 asserted. [5] 1 = GPI4 asserted. [6] 1 = MR asserted. [7] Not used. and WDI_ bits assert if any of the GPI_ inputs are configured as watchdog inputs (WDI_) and a watchdog fault occurs. Configuration Lock Lock the configuration register bank and configuration EEPROM contents after initial programming by setting the lock bit high (see Table 30). Locking the configuration prevents write operations to all registers except the configuration lock register. Clear the lock bit to reconfigure the device. 44 Write Disable A unique write disable feature protects the MAX6870/ MAX6871 from inadvertent user EEPROM writes. As input voltages that power the serial interface, a µP, or any other writing devices fall, unintentional data may be written onto the data bus. The user EEPROM write disable function (see Table 31) ensures that unintentional data does not corrupt the MAX6870/MAX6871 EEPROM data. ______________________________________________________________________________________ EEPROM-Programmable Hex/Quad Power-Supply Sequencers/Supervisors with ADC REGISTER ADDRESS EEPROM MEMORY ADDRESS 45h 8045h BIT RANGE [0] [7:1] MAX6870/MAX6871 Table 30. Configuration Lock Register DESCRIPTION 0 = configuration unlocked. 1 = configuration locked. Not used. Table 31. Write Disable Register REGISTER ADDRESS 43h EEPROM MEMORY ADDRESS BIT RANGE DESCRIPTION [0] 0 = write not disabled if PO1 asserts (MAX6870). 1 = write disabled if PO1 asserts (MAX6870). Set to 0 (MAX6871). [1] 0 = write not disabled if PO2 asserts (MAX6870). 1 = write disabled if PO2 asserts (MAX6870). Set to 0 (MAX6871). [2] 0 = write not disabled if PO3 (MAX6870)/PO1 (MAX6871) asserts. 1 = write disabled if PO3 (MAX6870)/PO1 (MAX6871) asserts. [3] 0 = write not disabled if PO4 (MAX6870)/PO2 (MAX6871) asserts. 1 = write disabled if PO4 (MAX6870)/PO2 (MAX6871) asserts. [4] 0 = write not disabled if PO5 (MAX6870)/PO3 (MAX6871) asserts. 1 = write disabled if PO5 (MAX6870)/PO3 (MAX6871) asserts. [5] 0 = write not disabled if PO6 (MAX6870)/PO4 (MAX6871) asserts. 1 = write disabled if PO6 (MAX6870)/PO4 (MAX6871) asserts. [6] 0 = write not disabled if PO7 (MAX6870)/PO5 (MAX6871) asserts. 1 = write disabled if PO7 (MAX6870)/PO5 (MAX6871) asserts. [7] 0 = write not disabled if PO8 asserts (MAX6870). 1 = write disabled if PO8 asserts (MAX6870). Set to 0 (MAX6871). 8043h Applications Information Configuration Download at Power-up The configuration of the MAX6870/MAX6871 (undervoltage/overvoltage thresholds, PO_ timeout periods, watchdog behavior, programmable output conditions and configurations, etc.) depends on the contents of the EEPROM. The EEPROM is comprised of buffered latches that store the configuration. The local volatile memory latches lose their contents at power-down. Therefore, at power-up, the device configuration must be restored by downloading the contents of the EEPROM (non-volatile memory) to the local latches. This download occurs in a number of steps: 1) Programmable outputs go high impedance with no power applied to the device. 2) When ABP exceeds +1V, all programmable outputs are weakly pulled to GND through a 10µA current sink. 3) When ABP exceeds UVLO, the configuration EEPROM starts to download its contents to the volatile configuration registers. The programmable outputs assume their programmed conditional output state when download is complete. 4) Any attempt to communicate with the device prior to this download completion results in a NACK being issued from the MAX6870/MAX6871. ______________________________________________________________________________________ 45 MAX6870/MAX6871 EEPROM-Programmable Hex/Quad Power-Supply Sequencers/Supervisors with ADC Forcing Programmable Outputs High During Power-Up A weak 10µA pulldown holds all programmable outputs low during power-up until ABP exceeds the undervoltage lockout (UVLO) threshold. Applications requiring a guaranteed high programmable output for ABP down to GND require external pullup resistors to maintain the logic state until ABP exceeds UVLO. Use 20kΩ resistors for most applications. Driving High-Side MOSFET Switches with the MAX6870/MAX6871 High-side MOSFET switches are commonly used in power-supply sequencing applications. First, configure the programmable output of the MAX6870/MAX6871 as an active-low charge-pump output and set the conditions to assert this output. Connect the programmable output to the gate of an n-channel MOSFET. As the conditions to deassert this output are met, the output deasserts high (VABP +5V), turning on the FET, thus allowing the voltage on the drain to pass through to the downstream device (see Figure 9). Uses for GeneralPurpose Inputs (GPI1–GPI4) Watchdog Timer Program GPI_ as an input to one of the watchdog timers in the MAX6870/MAX6871. The GPI_ input must toggle within the watchdog timeout period, otherwise any programmable output dependent on the watchdog timer asserts. Additional Manual Reset Functions The PO7 (MAX6870)/PO5 (MAX6871) programmable outputs allow a single set (Product 1 only) of conditions to assert the output. Program the set of conditions to depend on one of the GPI_ inputs. Any output that depends on GPI_ asserts when GPI_ is held in its active state, effectively acting as a manual reset input. Other Fault Signals from µC Connect a general purpose output from a µC to one of the GPI_ inputs to allow interrupts to assert any output of the MAX6870/MAX6871. Configure one of the programmable outputs to assert on whichever GPI_ input connects to the general purpose output of the µC. Uses for AUXIN1 and AUXIN2 Analog Output of Current-Sense Amplifier Figure 10 shows the MAX6870/MAX6871 in a currentsensing application with the MAX4374. The MAX4374 generates an analog output voltage (OUT) proportional to the voltage difference between RS+ and RS- and a latched comparator output (COUT) indicating an overcurrent condition. Connect OUT to AUXIN1 to provide continuous monitoring of the load current on the 12V supply. The internal ADC of the MAX6870/MAX6871 digitizes VOUT and stores the results in read-only registers 5Ch through 5Fh. COUT latches high for VCIN > 600mV, and clears with the RESET input of the MAX4374. Configure GPI1 as an active-high input and configure PO7 (MAX6870)/PO5 (MAX6871) to depend on GPI1. PO7/PO5 asserts to its active state when an overcurrent condition exists. ILOAD RSENSE TO LOAD +5V TO OTHER CIRCUITRY +12V RS+ RS- IN3 IN1 AUXIN1 OUT VCC PO1 R1 MAX4374 MAX6870 MAX6871 CIN R2 MAX6870 MAX6871 +5V PO7/ PO5 IN3 R3 RESET GND Figure 9. Driving High-Side n-Channel MOSFET Switches 46 COUT GPI1 GND GND Figure 10. Monitoring Current-Sense Amplifier Outputs ______________________________________________________________________________________ EEPROM-Programmable Hex/Quad Power-Supply Sequencers/Supervisors with ADC +5V VDD RPU VOUT VTH (
MAX6870ETJ+G05 价格&库存

很抱歉,暂时无法提供与“MAX6870ETJ+G05”相匹配的价格&库存,您可以联系我们找货

免费人工找货