OP11E

a FEATURES Guaranteed VOS: 500 V Max Guaranteed Matched CMRR: 94 dB Min Guaranteed Matched VOS: 750 V Max LM148/LM348 Direct Replacement Low Noise Silicon-Nitride Passivation Internal Frequency Compensation Low Crossover Distortion Continuous Short-Circuit Protection Low Input Bias Current Quad Matched 741-Type Operational Amplifiers OP11 PIN CONFIGURATIONS 14-Lead Epoxy DIP (P Suffix) OUT A –IN A +IN A V+ 1 2 3 4 14 OUT D 13 –IN D 12 +IN D 11 V– 10 +IN C 9 –IN C 8 OUT C +IN B 5 –IN B 6 OUT B 7 GENERAL DESCRIPTION The OP11 provides four matched 741-type operational amplifiers in a single 14-lead DIP package. The OP11 is pin compatible with the LM148, LM348, RM4156, RM4158, and HA4741 amplifiers. The amplifier is matched for common-mode rejection ratio and offset voltage which is very important in designing instrumentation amplifiers. In addition, the amplifier is designed to have equal positive-going and negative-going slew rates. This is an important consideration for good audio system performance. The OP11 is ideal for use in designs requiring minimum space and cost while maintaining performance. 14-Lead Hermetic DIP (Y Suffix) OUT A –IN A +IN A V+ 1 2 3 4 14 OUT D 13 –IN D 12 +IN D 11 V– 10 +IN C 9 –IN C 8 OUT C +IN B 5 –IN B 6 OUT B 7 V+ –IN +IN OUTPUT V– Figure 1. Simplified Schematic R EV. A Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781/329-4700 www.analog.com Fax: 781/326-8703 © Analog Devices, Inc., 2002 OP11–SPECIFICATIONS ELECTRICAL CHARACTERISTICS (@ V = S 15 V, TA = 25 C, unless otherwise noted) OP11A/OP11E Min Typ Max 0.3 5.5 180 0.17 ± 12 0.29 ± 13 120 4 ± 11 100 ± 13 650 105 0.7 18 14 12 17 1.8 1.5 1.2 100 0.7 130 1.0 16 3.0 110 15 145 25 100 0.7 11 2.4 180 32 ± 11 100 0.5 20 300 0.1 ± 12 100 Min OP11F Typ 0.6 25 300 0.17 ± 13 120 4 ± 13 650 123 0.7 18 14 12 17 1.8 1.5 1.2 130 1.0 16 3.0 110 15 145 25 0.7 11 2.4 180 32 ± 11 50 Max 2.5 50 500 0.1 ± 12 70 Min OP11G Typ 1.2 75 300 0.17 ± 13 100 10 ± 13 500 210 0.7 18 14 12 17 1.8 1.5 1.2 130 1.0 16 3.0 110 15 145 25 340 100 Max 5.0 200 500 Unit mV nA nA MW V dB mV/V V V/mV mW mV p-p nV/÷Hz nV/÷Hz nV/÷Hz pA p-p pA/÷Hz pA/÷Hz pA/÷Hz dB V/ms kHz MHz ns % Parameter Input Offset Voltage Input Offset Current Input Bias Current Input Resistance Differential Mode1 Input Voltage Range Common-Mode Rejection Ratio Power Supply Rejection Ratio Output Voltage Swing Large-Signal Voltage Gain Power Consumption2 Input Noise Voltage Input Noise Voltage Density Input Noise Current Input Noise Current Density Channel Separation Slew Rate 2 Symbol VOS IOS IB RIN IVR CMRR Conditions RS = 10 kW VCM = ± 12 V, RS = 10 kW VS = ± 5 V to ± 15 V, R S £ 1 0 kW RL = 2 k W RL £ 2 kW, VO = ± 10 V VO = 0 V 0.1 Hz to 10 Hz fO = 10 Hz fO = 100 Hz fO = 1 MHz 0.1 Hz to 10 Hz fO = 10 Hz fO = 100 Hz fO = 1 MHz 100 PSRR VO AVO Pd en p-p en In p-p In CS SR VO = 20 V p-p BW tf OS AVCL = 1 AV = 1, VIN = 50 mV Large Signal Bandwidth3 Closed-Loop Bandwidth4 Rise Time Overshoot 3 3 11 2.4 NOTES 1 Guaranteed by input bias current. 2 Total dissipation for all four amplifiers in package. 3 Sample tested. 4 Guaranteed by rise time. Specifications subject to change without notice – 2– REV. A OP11 ELECTRICAL CHARACTERISTICS Parameter Input Offset Voltage Average Input Offset Voltage Drift1 Input Offset Current Average Input Offset Current Drift Input Bias Current Input Voltage Range Common-Mode Rejection Ratio Power Supply Rejection Ratio Large-Signal Voltage Gain Output Voltage Swing Power Consumption2 NOTES 1 Guaranteed but not tested. 2 Total dissipation for all four amplifiers in package. Specifications subject to change without notice 1 (@ VS = 15 V, 55 C £ TA £ otherwise noted) Conditions RS £ 10 kW RS £ 10 kW 125 C for OP11A, 0 C £ TA £ 70 C for OP11E, unless OP11A Typ Max 0.4 2.0 20 0.1 200 ± 12 ± 13 120 4 50 ± 11 250 ± 13 115 200 32 50 ± 11 1.0 10 40 0.3 375 ± 12 100 OP11E Typ Max 0.4 2.0 14 0.1 200 ± 13 120 4 250 ± 13 115 200 32 0.8 10 30 0.3 350 Symbol VOS TCVOS IOS TCIOS IB IVR CMRR PSRR AVO VO Pd Min Min Unit mV mV/∞C nA nA/∞C nA V dB mV/V V/mV V mW VCM = ± 12 V, RS £ 10 kW VS = ± 5 V to ± 15 V, RS £ 10 kW RL ≥ 2 kW, VO = ± 10 V RL ≥ 2 kW VO = 0 V 100 ELECTRICAL CHARACTERISTICS (@ V = S 15 V, 40 C £ TA £ +85 C, RS £ 100 Min , unless otherwise noted) Min OP11G Typ Max 1.5 4.0 250 0.3 400 ± 12 70 32 25 ± 11 200 ± 13 100 10 100 ± 13 250 400 100 300 0.6 800 6 .0 Unit mV mV/∞C nA nA/∞C nA V dB mV/V V/mV V mW Parameter Input Offset Voltage Average Input Offset Voltage Drift Input Offset Current Average Input Offset Current Drift1 Input Bias Current Input Voltage Range Common-Mode Rejection Ratio Power Supply Rejection Ratio Large-Signal Voltage Gain Output Voltage Swing Power Consumption 2 Symbol VOS TCVOS IOS TCIOS IB IVR CMRR PSRR AVO VO Pd Conditions RS £ 10 kW RS £ 10 kW OP11F Typ Max 0.8 4.0 40 0.3 400 3.0 15 60 0.6 550 ± 12 VCM = ± 12 V, RS £ 10 kW VS = ± 5 V to ± 15 V, RS £ 10 kW RL ≥ 2 kW, VO = ± 10 V RL ≥ 2 kW VO = 0 V 50 ± 11 100 ± 13 120 4 250 ± 13 115 NOTES 1 Guaranteed but not tested. 2 Total dissipation for all four amplifiers in package. Specifications subject to change without notice REV. A – 3– OP11 ABSOLUTE MAXIMUM RATINGS * Supply Voltage (VS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 22 V Input Voltage* . . . . . . . . . . . . . . . . . . . . . . . . . Supply Voltage Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . ± 30 V Output Short-Circuit Duration . . . . . . . . . . . . . . . Continuous (One Amp Only) Storage Temperature Range Y Package . . . . . . . . . . . . . . . . . . . . . . . . –65∞C to +150∞C P Package . . . . . . . . . . . . . . . . . . . . . . . . . –65∞C to +125∞C Lead Temperature Range (Soldering, 60 sec) . . . . . . . . 300∞C Operating Temperature Range OP11A . . . . . . . . . . . . . . . . . . . . . . . . . . . –55∞C to +125∞C OP11E . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0∞C to 70∞C OP11F, OP11G . . . . . . . . . . . . . . . . . . . . . –40∞C to +85∞C *Absolute maximum ratings apply to both DICE and packaged parts, unless otherwise noted. Package Type 14-Lead Plastic DIP (P) 14-Lead Hermetic DIP (Y) JA* JC Unit ∞C/W ∞C/W 83 108 39 15 *qJA is specified for worst-case conditions, i.e., qJA is specified for device in socket for CERDIP and P-DIP packages. ORDERING GUIDE Model OP11AY* OP11EP OP11EY* OP11FP* OP11GP Temperature Range –40∞C to +125∞C –40∞C to +125∞C 0∞C to 85∞C –40∞C to 85∞C –40∞C to 85∞C Package Description 14-Lead CERDIP 14-Lead Epoxy DIP 14-Lead CERDIP 14-Lead Epoxy DIP 14-Lead Epoxy DIP Package Option Y-14 P-14 Y-14 P-14 P-14 *Not for new designs. Obsolete April 2002. For Military processed devices, please refer to the Standard Microcircuit Drawing (SMD) available at www.dscc.dla.mil/programs/milspec/default.asp SMD Part Number 5962-89801012A 5962-8980101CA ADI Equivalent OP11ARCMDA OP11AYMDA MATCHING CHARACTERISTICS (@ V = S 15 V, TA = 25 C, RS £ 100 Conditions VCM = ± 12 V VCM = ± 12 V , unless otherwise noted) OP11A, OP11E Min Typ Max 0.5 94 1 120 0.75 20 94 Min OP11F Typ Max 0.6 1 120 2.0 20 Unit mV mV/V dB Parameter Input Offset Voltage Match Common-Mode Rejection Ratio Match Specifications subject to change without notice Symbol DVOS DCMRR MATCHING CHARACTERISTICS +85 C for OP11F, R £ 100 Parameter Input Offset Voltage Match Common-Mode Rejection Ratio Match Specifications subject to change without notice (@ VS = 15 V, 55 C £ TA £ +125 C for OP11A, 0 C £ TA £ 70 C for OP11E, , unless otherwise noted) S OP11A, OP11E Min Typ Max 0.6 1.0 20 94 Min 40 C £ T A £ Symbol DVOS DCMRR Conditions VCM = ± 12 V VCM = ± 12 V OP11F Typ Max 1.0 3.2 110 2.5 20 Unit mV mV/V dB 94 3.2 110 CAUTION ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection. Although the OP11 features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high-energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality. WARNING! ESD SENSITIVE DEVICE – 4– REV. A Typical Performance Characteristics– OP11 0.1 VS = 15V 800 700 OPEN-LOOP GAIN – V/mV 600 500 400 300 200 100 0.5 60 40 20 0 20 40 60 80 TEMPERATURE – C 100 120 140 0 60 40 20 0 20 40 60 80 TEMPERATURE – C 100 120 140 VS = 15V RL = 2k OFFSET VOLTAGE – mV 0.2 0.3 0.4 TPC 1. Input Offset Voltage vs. Temperature TPC 4. Open-Loop Gain vs. Temperature 20 VS = INPUT OFFSET CURRENT – nA 15V 120 VS = 15V RL = 2k TA = 25 C CL = 100pF 100 0 OPEN-LOOP GAIN – dB 80 45 10 60 PHASE 40 90 135 5 20 180 0 60 40 20 0 20 40 60 80 TEMPERATURE – C 100 120 140 0 0.1 1.0 10 100 1k 10k FREQUENCY – Hz 100k 1M 10M TPC 2. Offset Current vs. Temperature TPC 5. Open-Loop Gain and Phase vs. Frequency 300 NORMALIZED VALUE REFERRED TO 25 C VS = 15V 1.4 VS = 1.3 1.2 1.1 1.0 0.9 0.8 BANDWIDTH 0.7 0.6 60 40 20 0 20 40 60 80 TEMPERATURE – C 100 120 140 60 40 20 0 20 40 60 80 TEMPERATURE – C 100 120 140 SLEW RATE 15V INPUT BIAS CURRENT – nA 200 100 0 TPC 3. Bias Current vs. Temperature TPC 6. Normalized Slew Rate and Bandwidth vs. Temperature REV. A – 5– PHASE LAG – Degrees 15 GAIN OP11 800 700 OPEN-LOOP GAIN – V/mV 140 RL = 2k TA = 25 C 120 VS = 15V TA = 25 C 600 500 400 300 200 100 0 CHANNEL SEPARATION – dB 100 80 60 40 20 0 10 0 5 10 15 POWER SUPPLY VOLTAGE – V 20 100 1k FREQUENCY – Hz 10k 100k TPC 7. Open-Loop Gain vs. Supply Voltage TPC 10. Channel Separation vs. Frequency 140 120 100 CMRR – dB 1k VS = 15V TA = 25 C VOLTAGE NOISE DENSITY – nV/ Hz VS = 15V TA = 25 C 100 80 60 40 20 0 1.0 10 10 100 1k FREQUENCY – Hz 10k 100k 1 10 100 1k FREQUENCY – Hz 10k TPC 8. CMRR vs. Frequency TPC 11. Voltage Noise Density vs. Frequency 140 120 100 PSRR – dB 100 VS = 15V TA = 25 C CURRENT NOISE DENSITY – pA/ Hz VS = 15V TA = 25 C 10 80 60 40 20 0 1.0 1 10 100 1k FREQUENCY – Hz 10k 100k 0.1 10 100 1k FREQUENCY – Hz 10k TPC 9. PSRR vs. Frequency TPC 12. Noise Current Density vs. Frequency – 6– REV. A OP11 16 OUTPUT VOLTAGE SWING – V OUTPUT VOLTAGE – mV 20 VS = 15V RL = 2k TA = 25 C CL = 100pF 14 12 10 8 6 4 2 0 0.1 VS = 15V TA = 25 C POSITIVE SWING NEGATIVE SWING 0 20 0 200 400 TIME – ns 600 800 1 LOAD RESISTANCE TO GROUND – k 10 TPC 13. Transient Response TPC 16. Output Voltage vs. Load Resistance 5 3 2 OUTPUT VOLTAGE – V 1 0 1 2 3 QUIESCENT CURRENT – mA VS = 15V RL = 2k TA = 25 C CL = 100pF TA = 25 C 4 3 2 1 0 2 4 6 8 10 12 TIME – s 14 16 18 20 0 0 10 20 30 TOTAL SUPPLY VOLTAGE – V 40 TPC 14. Voltage Follower Pulse Response TPC 17. Quiescent Current vs. Supply Voltage 28 (27) 140 VS = 15V RL = 2k TA = 25 C VS = POWER CONSUMPTION – mW 15V OUTPUT VOLTAGE PEAK-TO-PEAK – V 24 20 16 12 8 4 0 1k 130 120 110 100 10k 100k FREQUENCY – Hz 1M 60 40 20 0 20 40 60 80 TEMPERATURE – C 100 120 140 TPC 15. Maximum Output Swing vs. Frequency TPC 18. Power Consumption vs. Temperature REV. A – 7– OUTLINE DIMENSIONS Dimensions shown in inches and (mm). 14-Lead Epoxy DIP (P Suffix) C02784-0-4/02(A) 0.325 (8.25) 0.300 (7.62) 0.195 (4.95) 0.115 (2.93) 0.015 (0.381) 0.008 (0.204) 0.320 (8.13) 0.290 (7.37) 0.060 (1.52) 0.015 (0.38) 15 0 0.015 (0.38) 0.008 (0.20) 0.795 (20.19) 0.725 (18.42) 14 1 8 7 0.280 (7.11) 0.240 (6.10) PIN 1 0.100 (2.54) BSC 0.210 (5.33) MAX 0.130 (3.30) 0.160 (4.06) MIN 0.115 (2.93) 0.022 (0.558) 0.070 (1.77) SEATING PLANE 0.014 (0.356) 0.045 (1.15) 0.060 (1.52) 0.015 (0.38) 14-Lead Hermetic DIP (Y Suffix) 0.005 (0.13) MIN 0.098 (2.49) MAX 14 8 7 PIN 1 1 0.310 (7.87) 0.220 (5.59) 0.100 (2.54) BSC 0.785 (19.94) MAX 0.200 (5.08) MAX 0.200 (5.08) 0.125 (3.18) 0.023 (0.58) 0.014 (0.36) 0.150 (3.81) MIN SEATING 0.070 (1.78) PLANE 0.030 (0.76) Revision History Location Data Sheet changed from REV. 0 to REV. A. Page Change OP-09/OP-11 to OP11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Global Edits to PIN CONNECTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Edits to Figure 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Edits to ABSOLUTE MAXIMUM RATINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Edits to ORDERING GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Edits to SPEC TABLES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4 Deletion of DICE CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Deletion of WAFER TEST LIMITS Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Deletion of TYPICAL ELECTRICAL CHARACTERISTICS Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 PRINTED IN U.S.A. – 8–