AMC317SK

AMC317 www.addmtek.com DESCRIPTION The AMC317 series is a 3-terminal adjustable regulator featuring output current of typical 1.2A over a wide output range from 1.2V to 20V. Only two external resistors are required to set the output voltage. This feature provides better line and load regulation than fixed regulators. Also, the AMC317 series offers full overload protection, current limit, and thermal protection features. In most applications, no capacitor is required for the AMC317. However, if the device is located far from the input filter capacitor, then an input bypass will be required. Also, in order to improve the transient response, an output capacitor is recommended. 1.2A / 3-TERMINAL ADJUSTABLE REGULATOR FEATURES Output current capability of 1.2A Wide output voltage range – adjustable from 1.2V to 20V Ripple rejection typically 80 dB Typically 0.1% load regulation Built-in over current, over temperature and overload protection. Internal thermal overload protection Available in 3-Lead TO-220, and surface mount 3-Lead TO-263. Identical pin assignment to earlier LM317 series. PACKAGE PIN OUT VIN VOUT A DJ 3-Pin Plastic TO-220 (Top View) 3-P in P lastic T O -263 S u rface M o u n t (To p View ) V IN V OUT AD J APPLICATIONS Voltage Regulators Power Supplies Current Regulators Switching Regulators Current Limiter Constant Current Battery Charger Current Limited Charger 3. VIN 2. V out 1. ADJ/GND V IN V OUT ADJ 3 -P in P la s tic S O T -2 2 3 S u rfa c e M o u n t (To p V ie w ) 3-Pin Plastic TO-252 Surface Mount (Top View) ORDER INFORMATION TA (°C) T Plastic TO-220 3-pin ST Plastic TO-263 3-pin SJ Plastic TO-252 3-pin SK Plastic SOT-223 3-pin 0 to 70 AMC317T AMC317ST AMC317SJ Append the letter “T” to part number (i.e. AMC317SK 0 to 70 AMC317TF (Lead Free) AMC317STF (Lead Free) AMC317SJF (Lead Free) AMC317SKF (Lead Free) Note: 1.All surface-mount packages are available in Tape & Reel. AMC317STT). 2.The letter “F” is marked for Lead Free process. Copyright © 2006 ADDtek Corp. 1 DD011_G -- MARCH 2007 AMC317 TYPICAL APPLICATION VIN AMC317 ADJ CIN 0.1µF R1 240Ω R2 5K COUT 1µF VOUT Note 1: CIN is required if the regulator is far from the filter capacitor. Note 2: COUT is recommended to improve the transient response. R2 Note 3: VOUT = 1.25V ( 1+ ) + IADJ (R2) R1 ABSOLUTE MAXIMUM RATINGS (Note 1) Input-Output Differential Voltage VD ……………..…………………………………………………………..20V Operating Junction temperature Plastic (T, ST Package) …………………………………………………………………………………… 150°C Storage Temperature Range ………………………………………………………………………. -65°C to 150°C Lead temperature (Soldering, 10 seconds) ………………………………………………………………….. 300°C Note 1: Exceeding these ratings could cause damage to the device. negative out of the specified terminal. All voltages are with respect to Ground. Currents are positive into, THERMAL DATA T, ST PACKAGE: Thermal Resistance-Junction to Tab, θJT Thermal Resistance-Junction to Ambient, θJA Junction Temperature Calculation: TJ = TA + (PD × θJA). The θJA numbers are guidelines for the thermal performance of the device/pc-board system. All of the above assume no ambient airflow. Maximum Power Calculation: PD(MAX)= TJ(MAX) – TA(MAX) θJA TJ(OC): Maximum recommended junction temperature 3.0°C /W 45°C /W TA(OC): Ambient temperature of the application θJA(OC/W): Junction-to-junction temperature thermal resistance of the package, and other heat dissipating materials. The maximum power dissipation for a single-output regulator is : PD(MAX) = [(VIN(MAX) - VOUT(NOM))] × IOUT(NOM) + VIN(MAX) × IQ Where: VOUT(NOM) = the nominal output voltage IOUT(NOM) = the nominal output current, and IQ = the quiescent current the regulator consumes at IOUT(MAX) VIN(MAX) = the maximum input voltage Then θJA = (150 OC – TA)/PD Copyright © 2006 ADDtek Corp. 2 DD011_G -- MARCH 2007 AMC317 RECOMMENDED OPERATING CONDITIONS Recommended Operating Parameter Symbol Min. Typ. Max. Input-Output differential Voltage VD 3 20 Load Current (with adequate heatsinking) IO 10 1200 Input Capacitor (VIN to GND) 0.1 Output Capacitor with ESR of 10Ω max., (VOUT to GND) 1.0 ELECTRICAL CHARACTERISTICS Unless otherwise specified, these specifications in bold type apply over the operating ambient temperature of 0°C to +70°C, VIN – VOUT = 5V, IOUT = 10mA,CIN = 0.1µF, COUT= 1.0µF, and are for DC characteristics only. (Low duty cycle pulse testing techniques are used which maintains junction and case temperatures equal to the ambient temperature.) Parameter Reference Voltage Line Regulation (see note 2) Load regulation Minimum Load Current Adjustment Pin Current Adjustment Pin Current Change Current Limit Symbol VREF VOI VOL IOUT(MIN) IADJ IADJ ICL Test Conditions 3V ≤ VIN – VOUT ≤ 20V, 10mA ≤ IOUT ≤ 1.2A, P ≤ 15W 3V ≤ VIN – VOUT ≤ 20V,TJ = 25°C 3V ≤ VIN – VOUT ≤ 20V 10mA ≤ IOUT ≤ 1.2A, TJ = 25°C 10mA ≤ IOUT ≤ 1.2A VIN – VOUT ≤ 20V Min. 1.20 AMC317 Typ. Max. 1.25 0.01 0.02 0.1 0.3 3.5 50 1.30 0.04 0.07 0.5 1.5 10 100 5.0 3.4 A Units V %/V % mA µA µA Units V mA µF µF Ripple Rejection Ratio (Note 3) Output Noise Voltage (Note 3) Long Term Stability (Note 3) Temperature Stability (Note 3) Note 2: Note 3: RR VO RMS VO(Temp) 3V ≤ VIN – VOUT ≤ 20V 0.2 10mA ≤ IOUT ≤ 1.2A (VIN – VOUT) ≤ 10V 1.2 2.2 (VIN – VOUT) ≤ 15V 0.8 1.1 (VIN – VOUT) = 20V 0.15 0.4 VOUT = 10V, f = 120Hz 65 VOUT = 10V, f = 120Hz, 10µF 66 80 capacitor between ADJ and GND 0.003 10Hz ≤ f ≤ 10KHz, TJ = 25°C TJ = 125 OC, and VIN – VOUT = 20V 0.3 1 TMIN ≤ TJ ≤ TMAX dB % %/1000hr % 1 Line regulation is defined as the percentage change in output voltage every 1V change at the input These parameters, although guaranteed, are not tested in production prior to shipment Copyright © 2006 ADDtek Corp. 3 DD011_G -- MARCH 2007 AMC317 TYPICAL APPLICATIONS AMC317 VIN VOUT ADJ R1 240 C2 0.1µF R2 720 TTL 1K C2 0.1µF C1 10µF R2 5K VIN AMC317 ADJ R1 240 VOUT D1 1N4002 C3 1µF C1 0.1µF 5V Logic Regulator with Shutdown (Minimum output ≈ 1.2V) Adjustable Regulator with Improved Ripple Rejection AMC317 VIN ADJ VOUT R1 1.2 2W LOAD 1A Current Regulator AMC317 VIN ADJ VOUT R1 1.2K R2 20K 1.2V –20V Regulator with Minimum Current (≈ 4 mA) C1 0.1µF AMC317 VIN ADJ VOUT Rs 0.2 9V – 40V R1 240 R2 2.4K VIN AMC317 ADJ VOUT R1 240 C1 1000µF R2 1.1K R3 1 Current Limited 6V Charger (Peak Current = 0.6A with 1Ω resistor) 12V Battery Charger Copyright © 2006 ADDtek Corp. 4 DD011_G -- MARCH 2007 AMC317 PACKAGE 3-Pin Plastic TO-220 E P Q H1 A F SEATING PLAN INCHES MIN A 0.140 TYP MAX 0.190 0.070 0.045 0.045 MILLIMETERS MIN 3.56 1.14 0.51 0.30 TYP MAX 4.83 1.78 1.14 1.14 16.51 10.67 2.79 5.33 1.40 6.86 2.92 14.73 4.09 3.43 6.35 b1 0.045 D b c 0.020 0.012 D 0.560 E e L1 0.650 14.22 0.420 0.110 0.210 0.055 9.65 2.29 4.83 0.51 5.84 2.03 12.7 3.53 2.54 - 0.380 0.090 e1 0.190 F L 0.020 - H1 0.230 J1 0.080 L 0.500 0.139 0.270 0.115 0.580 0.161 0.135 0.250 b1 e e1 b c J1 P Q 0.100 L1 - 3-Pin Surface Mount TO-263 INCHES E A c2 MILLIMETERS MAX 0.190 0.039 0.055 MIN 4.06 0.51 1.14 TYP 0.38 TYP. 1.14 8.64 9.65 1.40 9.65 10.29 MAX 4.83 0.99 1.40 MIN A b 0.160 0.020 TYP - b2 0.045 D L c 0.015 TYP. 0.055 0.380 0.405 c2 0.045 D 0.340 E L1 c L3 0.380 e L 0.100 BSC 0.575 - 2.54 BSC 15.88 2.79 2.92 1.78 b e b2 0.625 14.61 0.110 0.115 0.070 2.29 1.27 L1 0.090 L2 - L3 0.050 Copyright © 2006 ADDtek Corp. 5 DD011_G -- MARCH 2007 AMC317 3-Pin Surface Mount TO-252 (SJ) INCHES E b2 L2 SEATING PLAN MILLIMETERS MAX 0.094 0.050 0.215 0.023 0.023 0.220 0.265 MIN 2.18 1.02 5.21 0.46 0.46 5.33 6.35 TYP 0.61 2.29 BSC 4.58 BSC 9.40 0.51 0.64 1.52 10.41 1.02 2.03 MAX 2.39 1.27 5.46 0.58 0.58 5.59 6.73 A A1 c1 MIN A 0.086 TYP 0.024 - A1 0.040 b - b2 0.205 D H c 0.018 c1 0.018 D 0.210 L1 b e1 L E e c 0.250 e e1 0.090 BSC 0.180 BSC 0.410 0.040 0.080 H 0.370 L 0.020 L1 0.025 L2 0.060 3-Pin Surface Mount SOT-223 ( SK ) D A c MILLIMETERS MIN A A1 1.50 0.02 0.60 2.90 0.28 6.30 3.30 TYP 1.65 0.05 0.70 0.30 6.50 3.50 2.3 BSC 4.6 BSC 6.70 0.91 1.50 0° 7.00 1.00 1.75 5° 3° 7.30 1.10 2.00 10 ° MAX 1.80 0.08 0.80 3.15 0.32 6.70 3.70 B1 H E B B1 c K L D E e e1 A1 e e1 H L K α β B Copyright © 2006 ADDtek Corp. 6 DD011_G -- MARCH 2007 AMC317 IMPORTANT NOTICE ADDtek reserves the right to make changes to its products or to discontinue any integrated circuit product or service without notice, and advises its customers to obtain the latest version of relevant information to verify, before placing orders, that the information being relied on is current. A few applications using integrated circuit products may involve potential risks of death, personal injury, or severe property or environmental damage. ADDtek integrated circuit products are not designed, intended, authorized, or warranted to be suitable for use in life-support applications, devices or systems or other critical applications. Use of ADDtek products in such applications is understood to be fully at the risk of the customer. In order to minimize risks associated with the customer’s applications, the customer should provide adequate design and operating safeguards. ADDtek assumes to no liability to customer product design or application support. ADDtek warrants the performance of its products to the specifications applicable at the time of sale. ADDtek Corp. 9F, No. 20, Sec. 3, Bade Rd., Taipei, Taiwan, 105 TEL: 2-25700299 FAX: 2-25700196 Copyright © 2006 ADDtek Corp. 7 DD011_G -- MARCH 2007