LXD100-1750SW

LED Power Supplies 100W LED Power 100W LXD100 series LED Power Supply Dimmable LED Power Supplies LED POWER next generation power source FEATURES • High Efficiency (up to 91%) • Dimming Control • Active PFC (Typical 0.99) • IP67 Waterproof • OVP, SCP • -35 to 65°C deg operation • Universal Input 90-305VAC • UL8750 compliant • EN61347-1, -2-13 compliant The LXD100 series of dimmable LED power supplies from Excelsys Technologies can deliver up to 100W of output power in an extremely compact package size. The LXD100 series of constant current power supplies provides up to 4200mA of output current and 286V output voltage solutions for specific LED requirements. With industry leading efficiencies, and an extensive protection feature set, the LXD100 series provides high reliability and high performance in a compact package. Model Number Output Voltage Output Current Input Voltage Efficiency 90-305VAC OVP Latching max 401V LXD100-0350SW 172-286V 350mA LXD100-0450SW 132-222V 450mA 90-305VAC 311V LXD100-0700SW 86-143V 91.0% 700mA 90-305VAC 200V LXD100-1050SW 90.5% 57-95V 1050mA 90-305VAC 133V 90.5% LXD100-1400SW 43-71V 1400mA 90-305VAC 101V 90.5% LXD100-1750SW 34-57V 1750mA 90-305VAC 80V 90.5% LXD100-2100SW 29-48V 2100mA 90-305VAC 67V 90.5% LXD100-2450SW 25-41V 2450mA 90-305VAC 58V 90.5% LXD100-2800SW 22-36V 2800mA 90-305VAC 51V 90.0% LXD100-3150SW 19-32V 3150mA 90-305VAC 45V 90.0% LXD100-3570SW 17-28V 3570mA 90-305VAC 40V 90.0% LXD100-4200SW 14-24V 4200mA 90-305VAC 34V 90.0% 91.0% Input Specifications Parameter Input Voltage Range Input Frequency Range Input Current Inrush Current Power Factor Conditions/Description Universal Input Min 90 47 100VAC in, 100W output 230VAC in, 25°C, Cold Start 220VAC, 110VAC 0.96 Conditions/Description Min Nom Max 305 63 1.3 65 0.99 Units VAC Hz A A Nom Max ±1 ±3 Units % % ±5 3.0 10 1 % % pk-pk % s Output Specifications Parameter Line Regulation Load Regulation Voltage Range Output Current Range Ripple and Noise Overshoot Turn-on Delay Short Circuit Protection Over Voltage Protection See table of outputs % of Vout 20MHz Bandwidth. See Note H Measured at 220VAC and full load Auto Recovery Latching. See individual models OVP levels 0.6 1 General Specifications Parameter Isolation Voltage Efficiency Safety Agency Approvals No load Power Dissipation MTBF Lifetime Weight Operating Temperature Storage Temperature Relative Humidity Conditions/Description Input to Output See Note B Input to Chassis See individual models UL8750, EN61347-1, -2-13 Measured at 230 Vac MIL HDBK, 110VAC input, 80% load, 25°C 45°C, 110VAC Input, 80% Load Non-condensing (operating) Europe/Asia Excelsys Technologies Ltd 27 Eastgate Drive Eastgate Business Park Little Island, Cork, Ireland IRELAND Min 3750 1500 Nom Max Units VAC VAC % 1.0 W Hours Hours g °C °C %RH 90.5 394,000 118,000 1000 -35 -40 10 +65 +85 100 North America t: +353 21 4354716 Excelsys Technologies f: +353 21 4354864 519 Interstate 30, #309 e: sales@excelsys.com Rockwall, TX 75087 USA t: (972) 771 4544 f: (972) 421 1805 e: salesusa@excelsys.com LED Power Supplies 100W EMC LED Power 100W Parameter Emissions Conducted Radiated Harmonic Distortion Flicker and Fluctuation Immunity ESD Radiated RFI Fast Transients - burst Surge Immunity Conducted RFI Power Freq Magnetic Field Voltage Dips Standard Level Units EN55015 EN55015 EN61000-3-2 EN61000-3-3 Compliant Compliant Compliant Compliant EN61000-4-2 EN61000-4-3 EN61000-4-4 EN61000-4-5 EN61000-4-6 EN61000-4-8 EN61000-4-11 Level 4 Level 3 Level 4 Level 4 Compliant Compliant Dimming Control Parameter 10V Output Voltage 10V Output Source Current Control Voltage (1-10V input Voltage applied on 1-10V input wire Source Current (1-10V input) Source current on 1-10V input wire Note Note Note Note Note A. B. C. D. E. Note F. Note G. Min 9.8 -10 0 0 Nom 10.0 Max 10.2 10 12 1 Units VDC mA V mA If dimming function is not required, dimming wires are to be floating Primary to Secondary Isolation test not to be carried on power supply. Load Voltage must be maintained above minimum voltage. See models for voltage range. Dimming range is 10%-100% See graphs for Dimming control. If Dimming Signal Voltage is 0-1V, output current is 10% rated current. If Dimming Sgnal Voltage is 8.5-10V,, output current is 100% rated current See Dimming Implementation diagrams for various dimming methods. Do not connect GND of Dimming cable to Output.. INPUT / OUTPUT WIRING INPUT CABLE SJTW 18AWG 3C Black (L),White(N), Green (G)650±20mm MECHANICAL SPECIFICATIONS OUTPUT CABLE SJTW 18AWG 2C Black (-V) and Red (+V) 220±20mm DIMMING CABLE SJTW 22AWG 3C Yellow (10V), Purple (1-10V), Green (GND) 221 194 190 300 ± 20 Input 50±5 Output 50±5 15±2 220 ± 20 37 650 ± 20 208 204 10.5 5 8 50 34 15±2 37 15±2 67.5 Dimming Control 50±5 40±5 30±5 5 Europe/Asia Excelsys Technologies Ltd 27 Eastgate Drive Eastgate Business Park Little Island, Cork, Ireland IRELAND North America t: +353 21 4354716 Excelsys Technologies f: +353 21 4354864 519 Interstate 30, #309 e: sales@excelsys.com Rockwall, TX 75087 USA t: (972) 771 4544 f: (972) 421 1805 e: salesusa@excelsys.com LED Power Supplies 100W Dimming Implementation Diagrams LED Power 100W Specifications are subject to change without notice LXD100 Datasheet Release 8 April 2011 Europe/Asia Excelsys Technologies Ltd 27 Eastgate Drive Eastgate Business Park Little Island, Cork, Ireland IRELAND North America t: +353 21 4354716 Excelsys Technologies f: +353 21 4354864 519 Interstate 30, #309 e: sales@excelsys.com Rockwall, TX 75087 USA t: (972) 771 4544 f: (972) 421 1805 e: salesusa@excelsys.com