LXD120-4900SW

LED Power Supplies 120W LED Power 120W LXD120 series LED Power Supply Dimmable LED Power Supplies LED POWER next generation power source FEATURES • High Efficiency (up to 91%) • Dimming Control • Active PFC (Typical 0.99) • IP67 Waterproof • OVP, SCP • -35 to 65°C deg operation • Universal Input 90-305VAC • UL8750 compliant • EN61347-1, -2-13 compliant The LXD120 series of dimmable LED power supplies from Excelsys Technologies can deliver up to 120W of output power in an extremely compact package size. The LXD120 series of constant current power supplies provides up to 4900mA of output current and 343V output voltage solutions for specific LED requirements. With industry leading efficiencies, and an extensive protection feature set, the LXD120 series provides high reliability and high performance in a compact package. Model Number Output Voltage Output Current Input Voltage Efficiency 90-305VAC OVP Latching max 480V LXD120-0350SW 206-343V 350mA LXD120-0450SW 160-266V 450mA 90-305VAC 373V LXD120-0700SW 103-171V 91.0% 700mA 90-305VAC 240V LXD120-1050SW 91.0% 68-114V 1050mA 90-305VAC 160V 90.5% LXD120-1400SW 52-86V 1400mA 90-305VAC 121V 90.5% LXD120-1750SW 41-68V 1750mA 90-305VAC 96V 90.5% LXD120-2100SW 34-57V 2100mA 90-305VAC 80V 90.5% LXD120-2450SW 29-49V 2450mA 90-305VAC 69V 90.5% LXD120-2800SW 26-43V 2800mA 90-305VAC 61V 90.5% LXD120-3150SW 23-38V 3500mA 90-305VAC 54V 90.0% LXD120-3500SW 20-34V 3500mA 90-305VAC 48V 90.0% LXD120-4200SW 17-28V 4200mA 90-305VAC 40V 90.0% LXD120-4900SW 14-24V 4900mA 90-305VAC 34V 90.0% 91.0% Input Specifications Parameter Input Voltage Range Input Frequency Range Input Current Inrush Current Power Factor Conditions/Description Universal Input Min 90 47 100VAC in, 120W output 230VAC in, 25°C, Cold Start 220VAC, 110VAC 0.96 Conditions/Description Min Nom Max 305 63 1.5 65 0.99 Units VAC Hz A A Nom Max ±1 ±3 Units % % ±5 3.0 10 1 % % pk-pk % s Output Specifications Parameter Line Regulation Load Regulation Voltage Range Output Current Range Ripple and Noise Overshoot Turn-on Delay Short Circuit Protection Over Voltage Protection See table of outputs % of Vout 20MHz Bandwidth. See Note H Measured at 220VAC and full load Auto Recovery Latching. See individual models OVP levels 0.6 1 General Specifications Parameter Isolation Voltage Efficiency Safety Agency Approvals No load Power Dissipation MTBF Lifetime Weight Operating Temperature Storage Temperature Relative Humidity Conditions/Description Input to Output See Note B Input to Chassis See individual models UL8750, EN61347-1, -2-13 Measured at 230 Vac MIL HDBK-217F, 110VAC input, 80% load, 25°C 45°C, 110VAC input, 80% load Non-condensing (operating) Europe/Asia Excelsys Technologies Ltd 27 Eastgate Drive Eastgate Business Park Little Island, Cork, Ireland IRELAND Min 3750 1500 Nom Max Units VAC VAC % 1.0 W Hours Hours g °C °C %RH 90.5 303,000 93,000 1000 -35 -40 10 +65 +85 100 North America t: +353 21 4354716 Excelsys Technologies f: +353 21 4354864 519 Interstate 30, #309 e: sales@excelsys.com Rockwall, TX 75087 USA t: (972) 771 4544 f: (972) 421 1805 e: salesusa@excelsys.com LED Power Supplies 120W EMC LED Power 120W Parameter Emissions Conducted Radiated Harmonic Distortion Flicker and Fluctuation Immunity ESD Radiated RFI Fast Transients - burst Surge Immunity Conducted RFI Power Freq Magnetic Field Voltage Dips Standard Level Units EN55015 EN55015 EN61000-3-2 EN61000-3-3 Compliant Compliant Compliant Compliant EN61000-4-2 EN61000-4-3 EN61000-4-4 EN61000-4-5 EN61000-4-6 EN61000-4-8 EN61000-4-11 Level 4 Level 3 Level 4 Level 4 Compliant Compliant Dimming Control Parameter Min Nom 10V Output Voltage 9.8 10.0 10V Output Source Current -10 Control Voltage (1-10V input Voltage applied on 1-10V input wire 0 Source Current (1-10V input) Source current on 1-10V input wire 0 Note A. If dimming function is not required, dimming wires are to be floating Note B. Primary to Secondary Isolation test not to be carried on power supply. Note C. Load Voltage must be maintained above minimum voltage. See models for voltage range. Note D. Dimming range is 10%-100% Note E. See graphs for Dimming control. If Dimming Signal Voltage is 0-1V, output current is 10% rated current. Voltage is 8.5-10V,, output current is 100% rated current Note F. See Dimming Implementation diagrams for various dimming methods. Note G. Do not connect GND of Dimming cable to Output.. Max 10.2 10 12 1 Units VDC mA V mA If Dimming Sgnal INPUT / OUTPUT WIRING INPUT CABLE SJTW 18AWG 3C Black (L),White(N), Green (G)650±20mm MECHANICAL SPECIFICATIONS OUTPUT CABLE SJTW 18AWG 2C Black (-V) and Red (+V) 220±20mm DIMMING CABLE SJTW 22AWG 3C Yellow (10V), Purple (0-10V), Green (GND) 221 194 190 37 15±2 67.5 50±5 40±5 30±5 50±5 50±5 15±2 220 ± 20 37 650 ± 20 208 204 10.5 5 8 50 34 15±2 300 ± 20 5 Specifications are subject to change without notice Europe/Asia Excelsys Technologies Ltd 27 Eastgate Drive Eastgate Business Park Little Island, Cork, Ireland IRELAND North America t: +353 21 4354716 Excelsys Technologies f: +353 21 4354864 519 Interstate 30, #309 e: sales@excelsys.com Rockwall, TX 75087 USA t: (972) 771 4544 f: (972) 421 1805 e: salesusa@excelsys.com LED Power Supplies 120W Dimming Implementation Diagrams LED Power 120W Specifications are subject to change without notice LXD120 Datasheet Release 8 April 2011 Europe/Asia Excelsys Technologies Ltd 27 Eastgate Drive Eastgate Business Park Little Island, Cork, Ireland IRELAND North America t: +353 21 4354716 Excelsys Technologies f: +353 21 4354864 519 Interstate 30, #309 e: sales@excelsys.com Rockwall, TX 75087 USA t: (972) 771 4544 f: (972) 421 1805 e: salesusa@excelsys.com