LXD26-0450SW

LED Power Supplies 26W LED Power 26W LXD26 series LED Power Supply Dimmable LED Power Supplies LED POWER next generation power source FEATURES • High Efficiency (up to 86%) • Constant Current Output • Active PFC (Typical 0.92) • IP66 Waterproof • OVP, SCP, OLP, OTP • -20 to 70°C deg operation • Input 90-305VAC • UL8750 compliant • EN61347-1, -2-13 compliant The LXD26 series of dimmable LED power supplies from Excelsys Technologies can deliver up to 26W of output power in an extremely compact package size. The LXD26 series of dimmable current power supplies provides up to 1750mA of output current and 75V output voltage solutions for specific LED requirements. With industry leading efficiencies, and an extensive protection feature set, the LXD26 series provides high reliability and high performance in a compact package. The LXD26 series carries the UL & CE mark for safety and is also RoHS compliant. Model Number Output Voltage Output Current Input Voltage Efficiency LXD26-0350SW(3) LXD26-0450SW(3) LXD26-0700SW(4) LXD26-1050SW(4) LXD26-1400SW(4) LXD26-1750SW(4) 38-75V 29-58V 19-37V 13-25V 10-19V 8-15V 350mA 450mA 700mA 1050mA 1400mA 1750mA 90-305VAC 90-305VAC 90-305VAC 90-305VAC 90-305VAC 90-305VAC 86.0% 86.0% 85.0% 84.0% 83.0% 83.0% Input Specifications Parameter Input Voltage Range Input Frequency Range Input Current Inrush Current Power Factor Conditions/Description Wide Input Min 90 47 100VAC in, 26W output 230VAC in, 25°C, Cold Start 220VAC, 110VAC 0.92 Conditions/Description Min Nom Max 305 63 0.40 60 0.98 Nom Max ±1 ±3 50 10 5.0 0.5 Units VAC Hz A A Output Specifications Parameter Line Regulation Load Regulation Over Current Ripple Overshoot/Output Current Ripple and Noise Turn-on Delay Short Circuit Protection Over Voltage Protection 20MHz Bandwidth. See Note 1 Measured at 220VAC and full load Auto Recovery Hiccup. Auto Recovery 0 3.0 0.3 Units % % % load % load V s General Specifications Parameter Isolation Voltage Efficiency Safety Agency Approvals No load Power Dissipation MTBF Lifetime Weight Operating Temperature Storage Temperature Relative Humidity Note Note Note Note 1. 2. 3. 4. Conditions/Description Input to Output See Note 2 Input to Chassis See individual models UL8750,EN61347-1, -2-13, UL1310 Class 2 (Notes 3 & 4) Measured at 120VAC and 220VAC MIL HDBK 217F, 110VAC input, 80% load, 25°C 110VAC input, 80% load, 45°C Min 3000 1500 Derate 1.5%/°C from 50°C to 70°C -20 -40 10 Non-condensing (operating) Nom Max Units VAC VAC % 84 5.0 130,000 70,000 200 +70 +85 100 Output connected in parallel with 0.1uF ceramic capacitor and 10uF electrolytic capacitor. Primary to Secondary Isolation test not to be carried out on power supply. Non UL1310 Class 2 outputs for US and Canada Specifications are subject UL1310 Class 2 outputs for US and Canada Europe/Asia North America Excelsys Technologies Ltd t: +353 21 4354716 Excelsys Technologies 27 Eastgate Drive f: +353 21 4354864 519 Interstate 30, #309 Eastgate Business Park e: sales@excelsys.com Rockwall, TX 75087 Little Island, Cork, Ireland USA IRELAND LXD26 Preliminary Datasheet 10 Mar 2012 1 W Hours Hours g °C °C %RH to change without notice t: (972) 771 4544 f: (972) 421 1805 e: salesusa@excelsys.com LED Power Supplies 26W EMC LED Power 26W Parameter Emissions Conducted Radiated Harmonic Distortion Flicker and Fluctuation Immunity ESD Radiated RFI Fast Transients - burst Conducted RFI Power Freq Magnetic Field Voltage Dips Standard Level EN55015 EN55015 EN61000-3-2 EN61000-3-3 Compliant Compliant Compliant Compliant EN61000-4-2 EN61000-4-3 EN61000-4-4 EN61000-4-6 EN61000-4-8 EN61000-4-11 Compliant Compliant Compliant Compliant Compliant Compliant Units Dimming Control Parameter 12V Output Voltage 12V Output Source Current Control Voltage (1-10V input Voltage applied on 1-10V input wire Source Current (1-10V input) Source current on 1-10V input wire Note Note Note Note Note Note Note A. B. C. D. E. F. G. Min 10.8 0 -2 0 Nom 12 Max 13.2 20 15 200 Units V mA V uA If dimming function is not used, 12V(yellow) and 1-10V(purple)wire must be connected together. Primary to Secondary Isolation test not to be carried on power supply. Load Voltage must be maintained above minimum voltage. See models for voltage range. Dimming range is 10%-100% Dimming Signal Voltage should be above 1V for linear dimming control. See Dimming Implementation diagrams for various dimming methods. Do not connect Dim - (Gray) cable to Output -V cable INPUT / OUTPUT WIRING INPUT CABLE 18AWG 2C Black (L),White(N) 270±20mm OUTPUT CABLE 18AWG 2C Black (-V) and Red (+V) 270±20mm DIMMING CABLE 22AWG 3C Yellow (12V), Purple (1-10V), Gray (Dim - ) 270±20mm MECHANICAL SPECIFICATIONS AC INPUT (18AWG) WHITE (ACN) BLACK (ACL) Dimming control wire (22AWG) Vaux(Yellow) Dim+(Purple) Dim-(Gray) RED (+) BLACK (-) DC OUTPUT (18AWG) 2 Specifications are subject to change without notice Europe/Asia Excelsys Technologies Ltd 27 Eastgate Drive Eastgate Business Park Little Island, Cork, Ireland IRELAND LXD26 Preliminary Datasheet 10 Mar 2012 North America t: +353 21 4354716 Excelsys Technologies f: +353 21 4354864 519 Interstate 30, #309 e: sales@excelsys.com Rockwall, TX 75087 USA t: (972) 771 4544 f: (972) 421 1805 e: salesusa@excelsys.com LED Power Supplies LED Power 26W Dimming Implementation Diagrams 26W EXCELSYS LED DRIVER Efficiency vs Load (350mA Model) Power Factor Characteristics 3 Specifications are subject to change without notice Europe/Asia Excelsys Technologies Ltd 27 Eastgate Drive Eastgate Business Park Little Island, Cork, Ireland IRELAND LXD26 Preliminary Datasheet 10 Mar 2012 North America t: +353 21 4354716 Excelsys Technologies f: +353 21 4354864 519 Interstate 30, #309 e: sales@excelsys.com Rockwall, TX 75087 USA t: (972) 771 4544 f: (972) 421 1805 e: salesusa@excelsys.com