LXD75-5000SW

LED Power Supplies 75W LED Power 75W LXD75 series LED Power Supply Dimmable LED Power Supplies LED POWER next generation power source FEATURES • High Efficiency (up to 92%) • Dimming Control • Active PFC (Typical 0.99) • IP67 Waterproof • OVP, SCP • -35 to 70°C deg operation • Universal Input 90-305VAC • UL8750 compliant • EN61347-1, -2-13 compliant The LXD75 series of dimmable LED power supplies from Excelsys Technologies can deliver up to 75W of output power in an extremely compact package size. The LXD75 series of dimming LED power supplies provide up to 5000mA of output current and 214V output voltage solutions for specific LED requirements. With industry leading efficiencies, and an extensive protection feature set, the LXD75 series provides high reliability and high performance in a compact package. Model Number Output Voltage Output Current Input Voltage Efficiency 90-305VAC OVP Latching max 250V LXD75-0350SW 107-214V 350mA LXD75-0450SW 83-166V 450mA 90-305VAC 215V LXD75-0700SW 54-108V 92.0% 700mA 90-305VAC 130V LXD75-1050SW 91.0% 36-72V 1050mA 90-305VAC 88V 90.0% LXD75-1400SW(3) 27-54V 1400mA 90-305VAC 70V 90.0% LXD75-2100SW(3) 18-36V 2100mA 90-305VAC 45V 89.0% LXD75-2800SW(3) 13-27V 2800mA 90-305VAC 38V 89.0% LXD75-3750SW(3) 10-20V 3750mA 90-305VAC 30V 88.0% LXD75-5000SW(3) 7-15V 5000mA 90-305VAC 25V 88.0% 92.0% Input Specifications Parameter Input Voltage Range Input Frequency Range Input Current Inrush Current Power Factor Conditions/Description Universal Input Min 90 47 100VAC in, 75W output 230VAC in, 25°C, Cold Start 220VAC, 110VAC 0.96 Conditions/Description Min See table of outputs See Dimming Graphs 20MHz Bandwidth. See Note 1 3.0 Nom Max 305 63 0.9 50 0.99 Units VAC Hz A A Nom Max ±1 ±3 Units % % 5.0 10 0.6 V % s Output Specifications Parameter Line Regulation Load Regulation Voltage Range Output Current Range Ripple and Noise Overshoot Turn-on Delay Short Circuit Protection Over Voltage Protection Measured at 220VAC and full load Auto Recovery Latching. See individual models OVP levels General Specifications Parameter Isolation Voltage Efficiency Safety Agency Approvals MTBF Lifetime Weight Operating Temperature Storage Temperature Relative Humidity Note 1. Note 2. Note 3. Conditions/Description Input to Output See Note 2 Input to Chassis See individual models UL8750, EN61347-1, -2-13,UL1310 Note 3 MIL HDBK-217F, 110VAC input, 80% load, 25°C 45°C, 110VAC Input, 80% Load Non-condensing (operating) Min 3000 1500 Nom Max 90 450,000 65,000 750 -35 -40 10 +70 +85 100 Units VAC VAC % 1 Hours Hours g °C °C %RH Output connected in parallel with 0.1uF ceramic capacitor and 10uF electrolytic capacitor. Primary to Secondary Isolation test not to be carried out on power supply. UL1310 Class 2 outputs for US and Canada except LXD75-1400SW which is Class 2 in US only Europe/Asia Excelsys Technologies Ltd 27 Eastgate Drive Eastgate Business Park Little Island, Cork, Ireland IRELAND North America t: +353 21 4354716 Excelsys Technologies f: +353 21 4354864 519 Interstate 30, #309 e: sales@excelsys.com Rockwall, TX 75087 USA t: (972) 771 4544 f: (972) 421 1805 e: salesusa@excelsys.com LED Power Supplies 75W EMC LED Power 75W Parameter Emissions Conducted Radiated Harmonic Distortion Flicker and Fluctuation Immunity ESD Radiated RFI Fast Transients - burst Surge Immunity Conducted RFI Power Freq Magnetic Field Voltage Dips Standard Level Units EN55015 EN55015 EN61000-3-2 EN61000-3-3 Compliant Compliant Compliant Compliant EN61000-4-2 EN61000-4-3 EN61000-4-4 EN61000-4-5 EN61000-4-6 EN61000-4-8 EN61000-4-11 Level 4 Level 3 Level 4 Level 4 Compliant Compliant Dimming Control Parameter 10V Output Voltage 10V Output Source Current Control Voltage (1-10V input Voltage applied on 1-10V input wire Source Current (1-10V input) Source current on 1-10V input wire Note Note Note Note Note A. B. C. D. E. Note F. Note G. Min 9.8 -10 -2 0 Nom 10.0 Max 10.2 10 12 0.5 Units VDC mA V mA If dimming function is not required, dimming wires are to be floating Primary to Secondary Isolation test not to be carried on power supply. Load Voltage must be maintained above minimum voltage. See models for voltage range. Dimming range is 10%-100% See graphs for Dimming control. If Dimming Signal Voltage is 0-1V, output current is 10% rated current. If Dimming Sgnal Voltage is 8.5-10V,, output current is 100% rated current See Dimming Implementation diagrams for various dimming methods. Do not connect GND of Dimming cable to Output.. INPUT / OUTPUT WIRING INPUT CABLE SJTW 18AWG 3C Black (L),White(N), Green (G)650±20mm OUTPUT CABLE SJTW 18AWG 2C Black (-V) and Red (+V) 220±20mm MECHANICAL SPECIFICATIONS DIMMING CABLE SJTW 22AWG 3C Yellow (10V), Purple (1-10V), Green (GND) 177 150 146 300 ± 20 Input 50±5 Output 50±5 15±2 220 ± 20 37 650 ± 20 164 160 10.5 5 8 50 34 15±2 37 10±2 67.5 Dimming Control 80±5 65±5 50±5 5 Specifications are subject to change without notice Europe/Asia Excelsys Technologies Ltd 27 Eastgate Drive Eastgate Business Park Little Island, Cork, Ireland IRELAND North America t: +353 21 4354716 Excelsys Technologies f: +353 21 4354864 519 Interstate 30, #309 e: sales@excelsys.com Rockwall, TX 75087 USA t: (972) 771 4544 f: (972) 421 1805 e: salesusa@excelsys.com LED Power Supplies 75W Dimming Implementation Diagrams LED Power 75W Specifications are subject to change without notice LXD75 Datasheet Release 8 April 2011 Europe/Asia Excelsys Technologies Ltd 27 Eastgate Drive Eastgate Business Park Little Island, Cork, Ireland IRELAND North America t: +353 21 4354716 Excelsys Technologies f: +353 21 4354864 519 Interstate 30, #309 e: sales@excelsys.com Rockwall, TX 75087 USA t: (972) 771 4544 f: (972) 421 1805 e: salesusa@excelsys.com