LXD85-1400SW

LED Power Supplies 85W LED Power 85W LXD85 series LED Power Supply Dimmable LED Power Supplies LED POWER next generation power source FEATURES • High Efficiency (up to 91%) • Dimming Control • UL1310 Class 2 • Active PFC (Typical 0.99) • IP67 Waterproof • OVP, SCP, OTP • -35 to 60°C deg operation • Universal Input 90-305VAC • UL8750 compliant • EN61347-1, -2-13 compliant The LXD85 series of Class 2 dimmable LED power supplies from Excelsys Technologies can deliver up to 85W of output power in an extremely compact package size. The LXD85 series of constant current power supplies provides up to 2800mA of output current and 243V output voltage solutions for specific LED requirements. With industry leading efficiencies, and an extensive protection feature set, the LXD85 series provides high reliability and high performance in a compact package. Model Number Output Voltage Output Current Input Voltage Efficiency 90-305VAC OVP Latching max 340V LXD85-0350SW 122-243V 350mA LXD85-0450SW 95-189V 450mA 90-305VAC 264V LXD85-0700SW 61-121V 91.0% 700mA 90-305VAC 170V LXD85-1050SW 90.0% 41-81V 1050mA 90-305VAC 113V 90.0% LXD85-1400SW 31-61V 1400mA 90-305VAC 85V 90.0% LXD85-1750SW(H) 25-49V 1750mA 90-305VAC 68V 90.0% LXD85-2000SW(H) 22-43V 2000mA 90-305VAC 60V 90.0% LXD85-2450SW(H) 18-35V 2450mA 90-305VAC 49V 89.0% LXD85-2800SW(H) 16-30V 2800mA 90-305VAC 43V 89.0% 91.0% Input Specifications Parameter Input Voltage Range Input Frequency Range Input Current Leakage Current Inrush Current Power Factor Conditions/Description Universal Input Min 90 47 100VAC in, 85W output 277VAC in, 50Hz 230VAC in, 25°C, Cold Start 220VAC, 110VAC 0.95 Conditions/Description Min Nom Max 305 63 1.1A 1.0 50 0.99 Units VAC Hz Max ±2 ±3 Units % % ±5 3.0 10 1 % % pk-pk % s mA A Output Specifications Parameter Line Regulation Load Regulation Voltage Range Output Current Accuracy Ripple and Noise Overshoot Turn-on Delay Short Circuit Protection Over Voltage Protection Over Temp Protection Nom See table of outputs % of Iout 20MHz Bandwidth. See Note H Measured at 220VAC and full load Auto Recovery Latching. See individual models OVP levels Latching Internal component temperature 0.6 120 °C 1 General Specifications Parameter Isolation Voltage Efficiency Safety Agency Approvals No load Power Dissipation MTBF Lifetime Weight Operating Temperature Storage Temperature Relative Humidity Conditions/Description Input to Output See Note B Input to Chassis See individual models UL8750, EN61347-1, -2-13 Measured at 230 VAC MIL-HDBK-217F, 110VAC input, 80% Load, 25°C 45°C, 110VAC Input, 80% Load Min 3750 1500 Maximum Case Temperatire Tcase =89°C -35 -40 10 Non-condensing (operating) Europe/Asia Excelsys Technologies Ltd 27 Eastgate Drive Eastgate Business Park Little Island, Cork, Ireland IRELAND Nom Max 90.5 1.0 300,000 63,000 770 +60 +85 100 North America t: +353 21 4354716 Excelsys Technologies f: +353 21 4354864 519 Interstate 30, #309 e: sales@excelsys.com Rockwall, TX 75087 USA Units VAC VAC % W Hours Hours g °C °C %RH t: (972) 771 4544 f: (972) 421 1805 e: salesusa@excelsys.com LED Power Supplies 85W EMC LED Power 85W Parameter Emissions Conducted Radiated Harmonic Distortion Flicker and Fluctuation Immunity ESD Radiated RFI Fast Transients - burst Surge Immunity Conducted RFI Power Freq Magnetic Field Voltage Dips Standard Level Units EN55015 EN55015 EN61000-3-2 EN61000-3-3 Compliant Compliant Compliant Compliant EN61000-4-2 EN61000-4-3 EN61000-4-4 EN61000-4-5 EN61000-4-6 EN61000-4-8 EN61000-4-11 Level 4 Level 3 Level 4 Level 4 Compliant Compliant Dimming Control Parameter Control Voltage (1-10V input Voltage applied on 1-10V input wire Source Current (1-10V input) Source current on 1-10V input wire Note Note Note Note Note A. B. C. D. E. Note F. Note G. Note H. Min -2 0 Nom Max 12 0.5 Units V mA If dimming function is not required, dimming wires are to be floating Primary to Secondary Isolation test not to be carried on power supply. Load Voltage must be maintained above minimum voltage. See models for voltage range. Dimming range is 10%-100% See graphs for Dimming control. If Dimming Signal Voltage is 0-1V, output current is 10% rated current. If Dimming Sgnal Voltage is 9.5-10V, output current is 100% rated current See Dimming Implementation diagrams for various dimming methods. Do not connect GND of Dimming cable to Output. Class 2 (USR and CNR)except for LXD85-1750SW and LXD85-2000SW which are Class 2 US only. INPUT / OUTPUT WIRING MECHANICAL SPECIFICATIONS OUTPUT CABLE SJTW 18AWG 2C Black (-V) and Red (+V) 220±20mm DIMMING CABLE SJTW 22AWG 2C Purple (1-10V), Grey (GND) 177 150 146 37 350 ± 20 Dimming Control 65 ± 5 50 ± 5 50 ± 5 15 ± 2 Output 50±5 220 ± 20 37 650 ± 20 164 160 10.5 5 8 5 50 34 15±2 Purple (1-10V) Grey (GND) 67.5 INPUT CABLE SJTW 18AWG 3C Black (L),White(N), Green (G)650±20mm Europe/Asia Excelsys Technologies Ltd 27 Eastgate Drive Eastgate Business Park Little Island, Cork, Ireland IRELAND North America t: +353 21 4354716 Excelsys Technologies f: +353 21 4354864 519 Interstate 30, #309 e: sales@excelsys.com Rockwall, TX 75087 USA t: (972) 771 4544 f: (972) 421 1805 e: salesusa@excelsys.com LED Power Supplies 85W Dimming Implementation Diagrams LED Power 85W Specifications are subject to change without notice LXD85 Datasheet Release 18 March 2011 Europe/Asia Excelsys Technologies Ltd 27 Eastgate Drive Eastgate Business Park Little Island, Cork, Ireland IRELAND North America t: +353 21 4354716 Excelsys Technologies f: +353 21 4354864 519 Interstate 30, #309 e: sales@excelsys.com Rockwall, TX 75087 USA t: (972) 771 4544 f: (972) 421 1805 e: salesusa@excelsys.com