APL501J

D S G D S G S SO 2 T- 27 APL501J 500V 43.0A 0.12W ISOTOP® "UL Recognized" File No. E145592 (S) POWER MOS IV ® MAXIMUM RATINGS Symbol VDSS ID IDM, lLM VGS PD TJ,TSTG TL Parameter Drain-Source Voltage Continuous Drain Current @ TC = 25°C Pulsed Drain Current Gate-Source Voltage Total Power Dissipation @ TC = 25°C Linear Derating Factor 1 SINGLE DIE ISOTOP® PACKAGE All Ratings: TC = 25°C unless otherwise specified. APL501J UNIT Volts Amps N - CHANNEL ENHANCEMENT MODE HIGH VOLTAGE POWER MOSFETS 500 43 172 ±30 520 4.16 -55 to 150 and Inductive Current Clamped Volts Watts W/°C °C Operating and Storage Junction Temperature Range Lead Temperature: 0.063" from Case for 10 Sec. 300 STATIC ELECTRICAL CHARACTERISTICS Symbol BVDSS ID(ON) RDS(ON) IDSS IGSS VGS(TH) Characteristic / Test Conditions / Part Number Drain-Source Breakdown Voltage (VGS = 0V, ID = 250 µA) On State Drain Current 2 MIN TYP MAX UNIT Volts Amps 500 43 0.12 25 (VDS > I D(ON) x R DS(ON) Max, VGS = 8V) 2 Drain-Source On-State Resistance (VGS = 10V, 0.5 ID [Cont.]) Ohms µA Zero Gate Voltage Drain Current (VDS = VDSS, VGS = 0V) Zero Gate Voltage Drain Current (VDS = 0.8 VDSS, VGS = 0V, TC = 125°C) Gate-Source Leakage Current (VGS = ±30V, VDS = 0V) Gate Threshold Voltage (VDS = VGS, ID = 2.5mA) 250 ±100 2 4 nA Volts THERMAL CHARACTERISTICS Symbol Characteristic RθJC RθJA Junction to Case Junction to Ambient MIN TYP MAX UNIT °C/W 0.28 40 2500 13 Volts lb•in 2-2002 050-5903 Rev D VIsolation RMS Voltage (50-60 Hz Sinusoidal Waveform From Terminals to Mounting Base for 1 Min.) Torque Maximum Torque for Device Mounting Screws and Electrical Terminations. CAUTION: These Devices are Sensitive to Electrostatic Discharge. Proper Handling Procedures Should Be Followed. APT Website - http://www.advancedpower.com USA EUROPE 405 S.W. Columbia Street Chemin de Magret Bend, Oregon 97702 -1035 F-33700 Merignac - France Phone: (541) 382-8028 Phone: (33) 5 57 92 15 15 FAX: (541) 388-0364 FAX: (33) 5 56 47 97 61 DYNAMIC CHARACTERISTICS Symbol Ciss Coss Crss td(on) tr td(off) tf Characteristic Input Capacitance Output Capacitance Reverse Transfer Capacitance Turn-on Delay Time Rise Time Turn-off Delay Time Fall Time Test Conditions VGS = 0V VDS = 25V f = 1 MHz VGS = 15V VDD = 0.5 VDSS ID = ID [Cont.] @ 25°C RG = 0.6Ω MIN TYP MAX APL501J UNIT 6040 1220 510 13 20 54 11 7300 1710 770 26 40 81 20 ns pF SAFE OPERATING AREA CHARACTERISTICS Symbol SOA1 Characteristic Safe Operating Area Test Conditions / Part Number VDS = 400 V, IDS = 0.813A, t = 20 sec., TC = 60°C MIN TYP MAX UNIT Watts 325 1 Repetitive Rating: Pulse width limited by maximum junction temperature. See Transient Thermal Impedance Curve. (Fig.1) 2 Pulse Test: Pulse width < 380 µS, Duty Cycle < 2% 3 See MIL-STD-750 Method 3471 0.3 Z JC, THERMAL IMPEDANCE (°C/W) θ D=0.5 0.1 0.05 0.2 0.1 0.05 0.01 0.005 0.02 0.01 SINGLE PULSE 0.001 10-5 10-4 Note: PDM t1 t2 Duty Factor D = t1/t2 Peak TJ = PDM x ZθJC + TC 10-3 10-2 10-1 1.0 10 RECTANGULAR PULSE DURATION (SECONDS) FIGURE 1, MAXIMUM EFFECTIVE TRANSIENT THERMAL IMPEDANCE, JUNCTION-TO-CASE vs PULSE DURATION 80 VGS=9V, 10V, 12V, 14 & 16V ID, DRAIN CURRENT (AMPERES) ID, DRAIN CURRENT (AMPERES) 80 8V VGS=10, 12, 14 & 16V 9V 8V 60 7V 40 6V 20 5V 0 60 7V 40 6V 20 5V 0 Rev D 2-2002 050-5903 0 20 40 60 80 100 VDS, DRAIN-TO-SOURCE VOLTAGE (VOLTS) FIGURE 2, TYPICAL OUTPUT CHARACTERISTICS 0 4 8 12 16 VDS, DRAIN-TO-SOURCE VOLTAGE (VOLTS) FIGURE 3, TYPICAL OUTPUT CHARACTERISTICS APL501J TJ = -55°C ID, DRAIN CURRENT (AMPERES) RDS(ON), DRAIN-TO-SOURCE ON RESISTANCE 40 TJ = +25°C 30 TJ = +125°C 1.30 V GS NORMALIZED TO = 10V @ 0.5 I [Cont.] D 1.20 VGS=10V 1.10 20 VDS> ID (ON) x RDS (ON)MAX. 250µSEC. PULSE TEST @