APT10040B2VR

APT10040B2VR APT10040LVR POWER MOS V ® Power MOS V® is a new generation of high voltage N-Channel enhancement mode power MOSFETs. This new technology minimizes the JFET effect, increases packing density and reduces the on-resistance. Power MOS V® also achieves faster switching speeds through optimized gate layout. B2VR 1000V 25A 0.400W T-MAX™ TO-264 LVR • Identical Specifications: T-MAX™ or TO-264 Package • Faster Switching • Lower Leakage MAXIMUM RATINGS Symbol VDSS ID IDM VGS VGSM PD TJ,TSTG TL IAR EAR EAS Parameter Drain-Source Voltage Continuous Drain Current @ TC = 25°C Pulsed Drain Current 1 D G S All Ratings: TC = 25°C unless otherwise specified. APT10040 UNIT Volts Amps 1000 25 100 ±30 ±40 625 5.0 -55 to 150 300 33 50 4 Gate-Source Voltage Continuous Gate-Source Voltage Transient Total Power Dissipation @ TC = 25°C Linear Derating Factor Operating and Storage Junction Temperature Range Lead Temperature: 0.063" from Case for 10 Sec. Avalanche Current 1 Volts Watts W/°C °C Amps mJ (Repetitive and Non-Repetitive) 1 Repetitive Avalanche Energy Single Pulse Avalanche Energy 3000 STATIC ELECTRICAL CHARACTERISTICS Symbol BVDSS ID(on) RDS(on) IDSS IGSS VGS(th) Characteristic / Test Conditions Drain-Source Breakdown Voltage (VGS = 0V, ID = 250µA) On State Drain Current 2 MIN TYP MAX UNIT Volts Amps 1000 25 0.400 25 250 2 4 ±100 (VDS > I D(on) x R DS(on) Max, VGS = 10V) 2 Drain-Source On-State Resistance (VGS = 10V, 0.5 ID[Cont.]) Ohms µA nA Volts 050-5909 RevA 5-2002 Zero Gate Voltage Drain Current (VDS = VDSS, VGS = 0V) Zero Gate Voltage Drain Current (VDS = 0.8 VDSS, VGS = 0V, TC = 125°C) Gate-Source Leakage Current (VGS = ±30V, VDS = 0V) Gate Threshold Voltage (VDS = VGS, ID = 2.5mA) APT Website - http://www.advancedpower.com CAUTION: These Devices are Sensitive to Electrostatic Discharge. Proper Handling Procedures Should Be Followed. USA EUROPE 405 S.W. Columbia Street Chemin de Magret Bend, Oregon 97702 -1035 F-33700 Merignac - France Phone: (541) 382-8028 Phone: (33) 5 57 92 15 15 FAX: (541) 388-0364 FAX: (33) 5 56 47 97 61 DYNAMIC CHARACTERISTICS Symbol Ciss Coss Crss Qg Qgs Qgd td(on) tr td(off) tf Characteristic Input Capacitance Output Capacitance Reverse Transfer Capacitance Total Gate Charge 3 APT10040 B2VR - LVR Test Conditions VGS = 0V VDS = 25V f = 1 MHz VGS = 10V VDD = 0.5 VDSS ID = 0.5 ID[Cont.] @ 25°C VGS = 15V VDD = 0.5 VDSS ID = ID[Cont.] @ 25°C RG = 0.6Ω MIN TYP MAX UNIT 7830 715 386 415 37 216 13 13 57 9 9400 1010 580 630 45 330 26 26 86 20 ns nC pF Gate-Source Charge Gate-Drain ("Miller ") Charge Turn-on Delay Time Rise Time Turn-off Delay Time Fall Time SOURCE-DRAIN DIODE RATINGS AND CHARACTERISTICS Symbol IS ISM VSD t rr Q rr Characteristic / Test Conditions Continuous Source Current Pulsed Source Current Diode Forward Voltage 1 2 revA 8-2000 MIN TYP MAX UNIT Amps Volts ns µC 050-5909 (Body Diode) (Body Diode) 25 100 1.3 1060 25.5 (VGS = 0V, IS = - ID[Cont.]) Reverse Recovery Time (IS = -ID[Cont.], dl S /dt = 100A/µs) Reverse Recovery Charge (IS = -ID[Cont.], dl S /dt = 100A/µs) THERMAL CHARACTERISTICS Symbol RθJC RθJA Characteristic Junction to Case Junction to Ambient MIN TYP MAX UNIT °C/W 0.20 40 3 See MIL-STD-750 Method 3471 4 Starting T = +25°C, L = 9.60mH, R = 25Ω, Peak I = 25A j G L 1 Repetitive Rating: Pulse width limited by maximum junction temperature. 2 Pulse Test: Pulse width < 380 µS, Duty Cycle < 2% APT Reserves the right to change, without notice, the specifications and information contained herein. 0.2 Z JC, THERMAL IMPEDANCE (°C/W) θ 0.1 0.05 D=0.5 0.2 0.1 0.01 0.005 0.05 0.02 0.01 SINGLE PULSE Note: PDM t1 t2 Duty Factor D = t1/t2 Peak TJ = PDM x ZθJC + TC 050-5909 Rev A 5-2002 0.001 10-5 10-3 10-2 10-1 1.0 RECTANGULAR PULSE DURATION (SECONDS) FIGURE 1, MAXIMUM EFFECTIVE TRANSIENT THERMAL IMPEDANCE, JUNCTION-TO-CASE vs PULSE DURATION 10-4 10 Typical Preformance Curves 60 50 VGS =7, 10 &15V 6V 40 30 5V 20 5.5V Graph Deleted ID, DRAIN CURRENT (AMPERES) 10 0 4.5V 4V VDS, DRAIN-TO-SOURCE VOLTAGE (VOLTS) FIGURE 2, HIGH VOLTAGE OUTPUT CHARACTERISTICS RDS(ON), DRAIN-TO-SOURCE ON RESISTANCE 0 5 10 15 20 25 VDS, DRAIN-TO-SOURCE VOLTAGE (VOLTS) FIGURE 3, LOW VOLTAGE OUTPUT CHARACTERISTICS 1.2 V GS 80 70 ID, DRAIN CURRENT (AMPERES) VDS> ID (ON) x RDS (ON)MAX. 250µSEC. PULSE TEST @