APT10078BFLL

1000V APT10078BFLL APT10078SFLL 14A BFLL D3PAK TO-247 0.780Ω POWER MOS 7 ® R FREDFET FREDFET Power MOS 7 is a new generation of low loss, high voltage, N-Channel enhancement mode power MOSFETS. Both conduction and switching ® losses are addressed with Power MOS 7 by significantly lowering RDS(ON) ® and Qg. Power MOS 7 combines lower conduction and switching losses along with exceptionally fast switching speeds inherent with APT's patented metal gate structure. • Lower Input Capacitance • Lower Miller Capacitance • Lower Gate Charge, Qg MAXIMUM RATINGS Symbol VDSS ID IDM VGS VGSM PD TJ,TSTG TL IAR EAR EAS Parameter Drain-Source Voltage Continuous Drain Current @ TC = 25°C Pulsed Drain Current 1 SFLL • Increased Power Dissipation • Easier To Drive • TO-247 or Surface Mount D3PAK Package • FAST RECOVERY BODY DIODE D G S All Ratings: TC = 25°C unless otherwise specified. APT10078BFLL_SFLL UNIT Volts Amps 1000 14 56 ±30 ±40 403 3.23 -55 to 150 300 14 30 4 Gate-Source Voltage Continuous Gate-Source Voltage Transient Total Power Dissipation @ TC = 25°C Linear Derating Factor Operating and Storage Junction Temperature Range Lead Temperature: 0.063" from Case for 10 Sec. Avalanche Current 1 Volts Watts W/°C °C Amps mJ (Repetitive and Non-Repetitive) 1 Repetitive Avalanche Energy Single Pulse Avalanche Energy 1300 STATIC ELECTRICAL CHARACTERISTICS Symbol BVDSS RDS(on) IDSS IGSS VGS(th) Characteristic / Test Conditions Drain-Source Breakdown Voltage (VGS = 0V, ID = 250µA) Drain-Source On-State Resistance 2 MIN TYP MAX UNIT Volts 1000 0.780 250 1000 ±100 3 5 (VGS = 10V, ID = 7A) Ohms µA nA Volts 4-2006 050-7040 Rev D Zero Gate Voltage Drain Current (VDS = 1000V, VGS = 0V) Zero Gate Voltage Drain Current (VDS = 800V, VGS = 0V, TC = 125°C) Gate-Source Leakage Current (VGS = ±30V, VDS = 0V) Gate Threshold Voltage (VDS = VGS, ID = 1mA) CAUTION: These Devices are Sensitive to Electrostatic Discharge. Proper Handling Procedures Should Be Followed. APT Website - http://www.advancedpower.com DYNAMIC CHARACTERISTICS Symbol Ciss Coss Crss Qg Qgs Qgd td(on) tr td(off) tf Eon Eoff Eon Eoff Symbol IS ISM VSD dv/ dt APT10078BFLL_SFLL Test Conditions VGS = 0V VDS = 25V f = 1 MHz VGS = 10V VDD = 500V ID = 14A @ 25°C RESISTIVE SWITCHING VGS = 15V VDD = 500V ID = 14A @ 25°C 6 INDUCTIVE SWITCHING @ 25°C VDD = 667V VGS = 15V INDUCTIVE SWITCHING @ 125°C VDD = 667V VGS = 15V ID = 14A, RG = 3Ω ID = 14A, RG = 3Ω RG = 1.6Ω Characteristic Input Capacitance Output Capacitance Reverse Transfer Capacitance Total Gate Charge 3 MIN TYP MAX UNIT pF 2525 430 75 95 12 60 9 8 30 9 355 75 740 95 MIN TYP MAX Gate-Source Charge Gate-Drain ("Miller") Charge Turn-on Delay Time Rise Time Turn-off Delay Time Fall Time Turn-on Switching Energy Turn-off Switching Energy Turn-on Switching Energy Turn-off Switching Energy Characteristic / Test Conditions Continuous Source Current (Body Diode) Pulsed Source Current Diode Forward Voltage Peak Diode Recovery 1 2 dt 6 nC ns µJ SOURCE-DRAIN DIODE RATINGS AND CHARACTERISTICS UNIT Amps Volts V/ns ns µC Amps 14 56 1.3 18 Tj = 25°C Tj = 125°C Tj = 25°C Tj = 125°C Tj = 25°C Tj = 125°C MIN (Body Diode) (VGS = 0V, IS = ID -14A) 5 d v/ t rr Q rr IRRM Reverse Recovery Time (IS = ID -14A, di/dt = 100A/µs) Reverse Recovery Charge (IS = ID -14A, di/dt = 100A/µs) Peak Recovery Current (IS = ID -14A, di/dt = 100A/µs) Characteristic Junction to Case Junction to Ambient 210 710 1.0 3.6 9.8 14 TYP MAX THERMAL CHARACTERISTICS Symbol RθJC RθJA UNIT °C/W 0.31 40 1 Repetitive Rating: Pulse width limited by maximum junction temperature 2 Pulse Test: Pulse width < 380 µs, Duty Cycle < 2% 3 See MIL-STD-750 Method 3471 0.35 Z JC, THERMAL IMPEDANCE (°C/W) θ 4 Starting Tj = +25°C, L = 13.27mH, RG = 25Ω, Peak IL = 14A 5 dv/dt numbers reflect the limitations of the test circuit rather than the device itself. IS ≤ ID-14A di/dt ≤ 700A/µs VR ≤ 1000 TJ ≤ 150°C 6 Eon includes diode reverse recovery. See figures 18, 20. APT Reserves the right to change, without notice, the specifications and inforation contained herein. 0.30 0.25 0.9 0.7 0.20 0.5 0.15 0.10 0.05 0 0.3 Note: PDM t1 t2 050-7040 Rev D 4-2006 0.1 0.05 10-5 10-4 SINGLE PULSE Peak TJ = PDM x ZθJC + TC Duty Factor D = t1/t2 10-3 10-2 10-1 RECTANGULAR PULSE DURATION (SECONDS) FIGURE 1, MAXIMUM EFFECTIVE TRANSIENT THERMAL IMPEDANCE, JUNCTION-TO-CASE vs PULSE DURATION 1.0 Typical Performance Curves ID, DRAIN CURRENT (AMPERES) Junction temp. (°C) RC MODEL 30 VGS =15 & 8V 25 20 15 10 APT10078BFLL_SFLL 7V 6.5V 0.0258 0.00295F Power (watts) 0.107 0.0114F 6V 0.177 Case temperature. (°C) 0.174F 5.5V 5 5V 0 5 10 15 20 25 30 VDS, DRAIN-TO-SOURCE VOLTAGE (VOLTS) FIGURE 3, LOW VOLTAGE OUTPUT CHARACTERISTICS 1.40 V GS 0 FIGURE 2, TRANSIENT THERMAL IMPEDANCE MODEL VDS> ID (ON) x RDS (ON)MAX. 250 µSEC. PULSE TEST @