APT11058B2FLL

APT11058B2FLL APT11058LFLL POWER MOS 7 ® 1100V 20A 0.580Ω R FREDFET T-MAX™ Power MOS 7 is a new generation of low loss, high voltage, N-Channel enhancement mode power MOSFETS. Both conduction and switching ® losses are addressed with Power MOS 7 by significantly lowering RDS(ON) ® and Qg. Power MOS 7 combines lower conduction and switching losses along with exceptionally fast switching speeds inherent with APT's patented metal gate structure. • Lower Input Capacitance • Lower Miller Capacitance • Lower Gate Charge, Qg MAXIMUM RATINGS Symbol VDSS ID IDM VGS VGSM PD TJ,TSTG TL IAR EAR EAS Parameter Drain-Source Voltage Continuous Drain Current @ TC = 25°C Pulsed Drain Current 1 TO-264 • Increased Power Dissipation • Easier To Drive • Popular T-MAX™ or TO-264 Package • FAST RECOVERY BODY DIODE D G S All Ratings: TC = 25°C unless otherwise specified. APT11058B2FLL_LFLL UNIT Volts Amps 1100 20 80 ±30 ±40 568 4.55 -55 to 150 300 20 50 4 Gate-Source Voltage Continuous Gate-Source Voltage Transient Total Power Dissipation @ TC = 25°C Linear Derating Factor Operating and Storage Junction Temperature Range Lead Temperature: 0.063" from Case for 10 Sec. Avalanche Current 1 Volts Watts W/°C °C Amps mJ (Repetitive and Non-Repetitive) 1 Repetitive Avalanche Energy Single Pulse Avalanche Energy 2500 STATIC ELECTRICAL CHARACTERISTICS Symbol BVDSS RDS(on) IDSS IGSS VGS(th) Characteristic / Test Conditions Drain-Source Breakdown Voltage (VGS = 0V, ID = 250µA) Drain-Source On-State Resistance 2 MIN TYP MAX UNIT Volts 1100 0.580 250 1000 ±100 3 5 (VGS = 10V, ID = 10A) Ohms µA nA Volts 4-2004 050-7181 Rev A Zero Gate Voltage Drain Current (VDS = 1100V, VGS = 0V) Zero Gate Voltage Drain Current (VDS = 880V, VGS = 0V, TC = 125°C) Gate-Source Leakage Current (VGS = ±30V, VDS = 0V) Gate Threshold Voltage (VDS = VGS, ID = 2.5mA) CAUTION: These Devices are Sensitive to Electrostatic Discharge. Proper Handling Procedures Should Be Followed. APT Website - http://www.advancedpower.com DYNAMIC CHARACTERISTICS Symbol Ciss Coss Crss Qg Qgs Qgd td(on) tr td(off) tf Eon Eoff Eon Eoff Symbol IS ISM VSD dv/ dt APT11058B2FLL_LFLL Test Conditions VGS = 0V VDS = 25V f = 1 MHz VGS = 10V VDD = 550V ID = 20A @ 25°C RESISTIVE SWITCHING VGS = 15V VDD = 550V ID = 20A @ 25°C 6 INDUCTIVE SWITCHING @ 25°C VDD = 733V, VGS = 15V INDUCTIVE SWITCHING @ 125°C VDD = 733V VGS = 15V ID = 20A, RG = 5Ω ID = 20A, RG = 5Ω RG = 0.6Ω Characteristic Input Capacitance Output Capacitance Reverse Transfer Capacitance Total Gate Charge 3 MIN TYP MAX UNIT pF 4135 680 120 160 20 105 16 8 40 12 700 210 1450 270 MIN TYP MAX Gate-Source Charge Gate-Drain ("Miller") Charge Turn-on Delay Time Rise Time Turn-off Delay Time Fall Time Turn-on Switching Energy Turn-off Switching Energy Turn-on Switching Energy Turn-off Switching Energy Characteristic / Test Conditions Continuous Source Current (Body Diode) Pulsed Source Current Diode Forward Voltage Peak Diode Recovery 1 2 dt 6 nC ns µJ SOURCE-DRAIN DIODE RATINGS AND CHARACTERISTICS UNIT Amps Volts V/ns ns µC Amps 20 80 1.3 18 Tj = 25°C Tj = 125°C Tj = 25°C Tj = 125°C Tj = 25°C Tj = 125°C MIN (Body Diode) (VGS = 0V, IS = -20A) 5 d v/ t rr Q rr IRRM Reverse Recovery Time (IS = -20A, di/dt = 100A/µs) Reverse Recovery Charge (IS = -20A, di/dt = 100A/µs) Peak Recovery Current (IS = -20A, di/dt = 100A/µs) Characteristic Junction to Case Junction to Ambient 340 640 1.78 4.47 11.4 16.4 TYP MAX THERMAL CHARACTERISTICS Symbol RθJC RθJA UNIT °C/W 0.22 40 1 Repetitive Rating: Pulse width limited by maximum junction temperature 2 Pulse Test: Pulse width < 380 µs, Duty Cycle < 2% 3 See MIL-STD-750 Method 3471 4 Starting Tj = +25°C, L = 12.50mH, RG = 25Ω, Peak IL = 20A 5 dv/dt numbers reflect the limitations of the test circuit rather than the device itself. IS ≤ -ID20A di/dt ≤ 700A/µs VR ≤ VDSS TJ ≤ 150°C 6 Eon includes diode reverse recovery. See figures 18, 20. APT Reserves the right to change, without notice, the specifications and information contained herein. 0.25 Z JC, THERMAL IMPEDANCE (°C/W) θ 0.20 0.9 0.15 0.7 0.5 4-2004 PDM 0.10 0.3 0.05 0.1 0.05 10-5 10-4 SINGLE PULSE Note: t1 t2 Duty Factor D = t1/t2 Peak TJ = PDM x ZθJC + TC 050-7181 Rev A 0 10-3 10-2 10-1 RECTANGULAR PULSE DURATION (SECONDS) FIGURE 1, MAXIMUM EFFECTIVE TRANSIENT THERMAL IMPEDANCE, JUNCTION-TO-CASE vs PULSE DURATION 1.0 Typical Performance Curves ID, DRAIN CURRENT (AMPERES) RC MODEL 45 40 35 30 25 20 15 10 5 0 APT11058B2FLL_LFLL VGS =15,10 & 7.5V 7V Junction temp. (°C) 0.0893 0.0102F 6.5V Power (watts) 0.0842 0.106F 6V 5.5V 5V 0.0485 Case temperature. (°C) 0.980F FIGURE 2, TRANSIENT THERMAL IMPEDANCE MODEL VDS> ID (ON) x RDS (ON)MAX. 250 µSEC. PULSE TEST @