APT20M20JFLL_04

APT20M20JFLL 200V 104A 0.020Ω POWER MOS 7 ® R FREDFET G S D S Power MOS 7 is a new generation of low loss, high voltage, N-Channel enhancement mode power MOSFETS. Both conduction and switching ® losses are addressed with Power MOS 7 by significantly lowering RDS(ON) ® and Qg. Power MOS 7 combines lower conduction and switching losses along with exceptionally fast switching speeds inherent with APT's patented metal gate structure. • Lower Input Capacitance • Lower Miller Capacitance • Lower Gate Charge, Qg • Increased Power Dissipation • Easier To Drive • Popular SOT-227 Package • FAST RECOVERY BODY DIODE SO 2 T- 27 "UL Recognized" ISOTOP ® D G S MAXIMUM RATINGS Symbol VDSS ID IDM VGS VGSM PD TJ,TSTG TL IAR EAR EAS Parameter Drain-Source Voltage Continuous Drain Current @ TC = 25°C Pulsed Drain Current 1 All Ratings: TC = 25°C unless otherwise specified. APT20M20JFLL UNIT Volts Amps 200 104 416 ±30 ±40 463 3.70 -55 to 150 300 100 50 4 Gate-Source Voltage Continuous Gate-Source Voltage Transient Total Power Dissipation @ TC = 25°C Linear Derating Factor Operating and Storage Junction Temperature Range Lead Temperature: 0.063" from Case for 10 Sec. Avalanche Current 1 Volts Watts W/°C °C Amps mJ (Repetitive and Non-Repetitive) 1 Repetitive Avalanche Energy Single Pulse Avalanche Energy 2500 STATIC ELECTRICAL CHARACTERISTICS Symbol BVDSS RDS(on) IDSS IGSS VGS(th) Characteristic / Test Conditions Drain-Source Breakdown Voltage (VGS = 0V, ID = 250µA) Drain-Source On-State Resistance 2 MIN TYP MAX UNIT Volts 200 0.020 250 1000 ±100 3 5 (VGS = 10V, ID = 52A) Ohms µA nA Volts 4-2004 050-7045 Rev D Zero Gate Voltage Drain Current (VDS = 200V, VGS = 0V) Zero Gate Voltage Drain Current (VDS = 160V, VGS = 0V, TC = 125°C) Gate-Source Leakage Current (VGS = ±30V, VDS = 0V) Gate Threshold Voltage (VDS = VGS, ID = 2.5mA) CAUTION: These Devices are Sensitive to Electrostatic Discharge. Proper Handling Procedures Should Be Followed. APT Website - http://www.advancedpower.com DYNAMIC CHARACTERISTICS Symbol Ciss Coss Crss Qg Qgs Qgd td(on) tr td(off) tf Eon Eoff Eon Eoff Symbol IS ISM VSD dv/ dt APT20M20JFLL Test Conditions VGS = 0V VDS = 25V f = 1 MHz VGS = 10V VDD = 100V ID = 104A @ 25°C RESISTIVE SWITCHING VGS = 15V VDD = 100V ID = 104A @ 25°C 6 INDUCTIVE SWITCHING @ 25°C VDD = 130V, VGS = 15V INDUCTIVE SWITCHING @ 125°C VDD = 130V, VGS = 15V ID = 104A, RG = 5Ω ID = 104A, RG = 5Ω RG = 0.6Ω Characteristic Input Capacitance Output Capacitance Reverse Transfer Capacitance Total Gate Charge 3 MIN TYP MAX UNIT pF 6850 2180 95 110 43 47 13 40 26 2 465 455 920 915 MIN TYP MAX Gate-Source Charge Gate-Drain ("Miller") Charge Turn-on Delay Time Rise Time Turn-off Delay Time Fall Time Turn-on Switching Energy Turn-off Switching Energy Turn-on Switching Energy Turn-off Switching Energy Characteristic / Test Conditions Continuous Source Current (Body Diode) Pulsed Source Current Diode Forward Voltage Peak Diode Recovery 1 2 dt 6 nC ns µJ SOURCE-DRAIN DIODE RATINGS AND CHARACTERISTICS UNIT Amps Volts V/ns ns µC Amps 104 416 1.3 8 Tj = 25°C Tj = 125°C Tj = 25°C Tj = 125°C Tj = 25°C Tj = 125°C MIN (Body Diode) (VGS = 0V, IS = -104A) 5 d v/ t rr Q rr IRRM Reverse Recovery Time (IS = -104A, di/dt = 100A/µs) Reverse Recovery Charge (IS = -104A, di/dt = 100A/µs) Peak Recovery Current (IS = -104A, di/dt = 100A/µs) Characteristic Junction to Case Junction to Ambient 220 420 1.07 2.9 12.1 20.6 TYP MAX THERMAL CHARACTERISTICS Symbol RθJC RθJA UNIT °C/W 0.27 40 1 Repetitive Rating: Pulse width limited by maximum junction temperature 2 Pulse Test: Pulse width < 380 µs, Duty Cycle < 2% 3 See MIL-STD-750 Method 3471 4 Starting Tj = +25°C, L = 0.46mH, RG = 25Ω, Peak IL = 104A 5 dv/dt numbers reflect the limitations of the test circuit rather than the device itself. IS ≤ -ID104A di/dt ≤ 700A/µs VR ≤ VDSS TJ ≤ 150°C 6 Eon includes diode reverse recovery. See figures 18, 20. APT Reserves the right to change, without notice, the specifications and inforation contained herein. 0.30 Z JC, THERMAL IMPEDANCE (°C/W) θ 0.25 0.9 0.20 0.7 0.15 0.5 Note: PDM t1 t2 Peak TJ = PDM x ZθJC + TC Duty Factor D = t1/t2 4-2004 0.10 0.05 0 0.3 050-7045 Rev D 0.1 0.05 10-5 10-4 SINGLE PULSE 10-3 10-2 10-1 1.0 RECTANGULAR PULSE DURATION (SECONDS) FIGURE 1, MAXIMUM EFFECTIVE TRANSIENT THERMAL IMPEDANCE, JUNCTION-TO-CASE vs PULSE DURATION 10 Typical Performance Curves RC MODEL 250 ID, DRAIN CURRENT (AMPERES) APT20M20JFLL VGS =15 &10V 9V Junction temp. ( ”C) 0.0409 0.0246F 200 150 7.5V 7V Power (Watts) 0.225 0.406F 100 6.5 50 6V 5.5V 0 5 10 15 20 25 30 VDS, DRAIN-TO-SOURCE VOLTAGE (VOLTS) FIGURE 3, LOW VOLTAGE OUTPUT CHARACTERISTICS 1.40 V GS 0.00361 Case temperature 0.147.639F 0 FIGURE 2, TRANSIENT THERMAL IMPEDANCE MODEL RDS(ON), DRAIN-TO-SOURCE ON RESISTANCE 200 180 ID, DRAIN CURRENT (AMPERES) VDS> ID (ON) x RDS(ON) MAX. 250µSEC. PULSE TEST @