APT20M34SFLL

APT20M34BFLL APT20M34SFLL 200V 74A 0.034Ω POWER MOS 7 ® R FREDFET BFLL D3PAK TO-247 Power MOS 7 is a new generation of low loss, high voltage, N-Channel enhancement mode power MOSFETS. Both conduction and switching ® losses are addressed with Power MOS 7 by significantly lowering RDS(ON) ® and Qg. Power MOS 7 combines lower conduction and switching losses along with exceptionally fast switching speeds inherent with APT's patented metal gate structure. • Lower Input Capacitance • Lower Miller Capacitance • Lower Gate Charge, Qg MAXIMUM RATINGS Symbol VDSS ID IDM VGS VGSM PD TJ,TSTG TL IAR EAR EAS Parameter Drain-Source Voltage Continuous Drain Current @ TC = 25°C Pulsed Drain Current 1 SFLL • Increased Power Dissipation • Easier To Drive • TO-247 or Surface Mount D3PAK Package • FAST RECOVERY BODY DIODE D G S All Ratings: TC = 25°C unless otherwise specified. APT20M34BFLL_SFLL UNIT Volts Amps 200 74 296 ±30 ±40 403 3.23 -55 to 150 300 74 30 4 Gate-Source Voltage Continuous Gate-Source Voltage Transient Total Power Dissipation @ TC = 25°C Linear Derating Factor Operating and Storage Junction Temperature Range Lead Temperature: 0.063" from Case for 10 Sec. Avalanche Current 1 Volts Watts W/°C °C Amps mJ (Repetitive and Non-Repetitive) 1 Repetitive Avalanche Energy Single Pulse Avalanche Energy 1300 STATIC ELECTRICAL CHARACTERISTICS Symbol BVDSS RDS(on) IDSS IGSS VGS(th) Characteristic / Test Conditions Drain-Source Breakdown Voltage (VGS = 0V, ID = 250µA) Drain-Source On-State Resistance 2 MIN TYP MAX UNIT Volts 200 0.034 250 1000 ±100 3 5 (VGS = 10V, ID = 37A) Ohms µA nA Volts 9-2004 050-7047 Rev B Zero Gate Voltage Drain Current (VDS = 200V, VGS = 0V) Zero Gate Voltage Drain Current (VDS = 160V, VGS = 0V, TC = 125°C) Gate-Source Leakage Current (VGS = ±30V, VDS = 0V) Gate Threshold Voltage (VDS = VGS, ID = 1mA) CAUTION: These Devices are Sensitive to Electrostatic Discharge. Proper Handling Procedures Should Be Followed. APT Website - http://www.advancedpower.com DYNAMIC CHARACTERISTICS Symbol Ciss Coss Crss Qg Qgs Qgd td(on) tr td(off) tf Eon Eoff Eon Eoff Symbol IS ISM VSD dv/ dt APT20M34BFLL_SFLL Test Conditions VGS = 0V VDS = 25V f = 1 MHz VGS = 10V VDD = 100V ID = 74A @ 25°C RESISTIVE SWITCHING VGS = 15V VDD = 100V ID = 74A @ 25°C 6 INDUCTIVE SWITCHING @ 25°C VDD = 133V, VGS = 15V INDUCTIVE SWITCHING @ 125°C VDD = 133V, VGS = 15V ID = 74A, RG = 5Ω ID = 74A, RG = 5Ω RG = 0.6Ω Characteristic Input Capacitance Output Capacitance Reverse Transfer Capacitance Total Gate Charge 3 MIN TYP MAX UNIT pF 3660 1170 60 60 23 26 10 27 25 4 505 395 640 425 MIN TYP MAX Gate-Source Charge Gate-Drain ("Miller") Charge Turn-on Delay Time Rise Time Turn-off Delay Time Fall Time Turn-on Switching Energy Turn-off Switching Energy Turn-on Switching Energy Turn-off Switching Energy Characteristic / Test Conditions Continuous Source Current (Body Diode) Pulsed Source Current Diode Forward Voltage Peak Diode Recovery 1 2 dt 6 nC ns µJ SOURCE-DRAIN DIODE RATINGS AND CHARACTERISTICS UNIT Amps Volts V/ns ns µC Amps 74 296 1.3 8 Tj = 25°C Tj = 125°C Tj = 25°C Tj = 125°C Tj = 25°C Tj = 125°C MIN (Body Diode) (VGS = 0V, IS = -74A) 5 dv/ t rr Q rr IRRM Reverse Recovery Time (IS = -74A, di/dt = 100A/µs) Reverse Recovery Charge (IS = -74A, di/dt = 100A/µs) Peak Recovery Current (IS = -74A, di/dt = 100A/µs) Characteristic Junction to Case Junction to Ambient 240 420 1.0 2.0 10 16 TYP MAX THERMAL CHARACTERISTICS Symbol RθJC RθJA UNIT °C/W 0.31 40 1 Repetitive Rating: Pulse width limited by maximum junction temperature 2 Pulse Test: Pulse width < 380 µs, Duty Cycle < 2% 3 See MIL-STD-750 Method 3471 0.35 Z JC, THERMAL IMPEDANCE (°C/W) θ 4 Starting Tj = +25°C, L = 0.470mH, RG = 25Ω, Peak IL = 74A 5 dv/dt numbers reflect the limitations of the test circuit rather than the device itself. IS ≤ -ID74A di/dt ≤ 700A/µs VR ≤ VDSS TJ ≤ 150°C 6 Eon includes diode reverse recovery. See figures 18, 20. APT Reserves the right to change, without notice, the specifications and information contained herein. 0.30 0.25 0.9 0.7 0.20 0.15 0.10 0.05 0 10-5 0.5 Note: PDM t1 t2 Peak TJ = PDM x ZθJC + TC Duty Factor D = t1/t2 9-2004 0.3 050-7047 Rev B 0.1 0.05 SINGLE PULSE 10-4 10-3 10-2 10-1 RECTANGULAR PULSE DURATION (SECONDS) FIGURE 1, MAXIMUM EFFECTIVE TRANSIENT THERMAL IMPEDANCE, JUNCTION-TO-CASE vs PULSE DURATION 1.0 Typical Performance Curves 160 140 120 100 80 60 40 20 0 APT20M34BFLL_SFLL VGS=10 &15V 6.5V RC MODEL Junction temp. (°C) 0.131 Power (watts) 0.180 Case temperature. (°C) 0.161F 0.00789F ID, DRAIN CURRENT (AMPERES) 6V 5.5V 5V 4.5V 4V FIGURE 2, HIGH VOLTAGE OUTPUT CHARACTERISTICS RDS(ON), DRAIN-TO-SOURCE ON RESISTANCE 120 100 80 60 40 20 0 TJ = +25°C TJ = +125°C TJ = -55°C VDS> ID (ON) x RDS (ON)MAX. 250 µSEC. PULSE TEST @