APT5010LLL

500V 46A APT5010B2LL APT5010LLL B2LL 0.100Ω POWER MOS 7 ® R MOSFET Power MOS 7 is a new generation of low loss, high voltage, N-Channel enhancement mode power MOSFETS. Both conduction and switching ® losses are addressed with Power MOS 7 by significantly lowering RDS(ON) ® and Qg. Power MOS 7 combines lower conduction and switching losses along with exceptionally fast switching speeds inherent with APT's patented metal gate structure. • Lower Input Capacitance • Lower Miller Capacitance • Lower Gate Charge, Qg MAXIMUM RATINGS Symbol VDSS ID IDM VGS VGSM PD TJ,TSTG TL IAR EAR EAS Parameter Drain-Source Voltage Continuous Drain Current @ TC = 25°C Pulsed Drain Current 1 T-MAX™ TO-264 LLL • Increased Power Dissipation • Easier To Drive • Popular T-MAX™ or TO-264 Package D G S All Ratings: TC = 25°C unless otherwise specified. APT5010B2LL_LLL UNIT Volts Amps 500 46 184 ±30 ±40 520 4.0 -55 to 150 300 50 50 4 Gate-Source Voltage Continuous Gate-Source Voltage Transient Total Power Dissipation @ TC = 25°C Linear Derating Factor Operating and Storage Junction Temperature Range Lead Temperature: 0.063" from Case for 10 Sec. Avalanche Current 1 Volts Watts W/°C °C Amps mJ (Repetitive and Non-Repetitive) 1 Repetitive Avalanche Energy Single Pulse Avalanche Energy 1600 STATIC ELECTRICAL CHARACTERISTICS Symbol BVDSS RDS(on) IDSS IGSS VGS(th) Characteristic / Test Conditions Drain-Source Breakdown Voltage (VGS = 0V, ID = 250µA) Drain-Source On-State Resistance 2 MIN TYP MAX UNIT Volts 500 0.100 100 500 ±100 3 5 (VGS = 10V, ID = 23A) Ohms µA nA Volts 9-2004 050-7011 Rev D Zero Gate Voltage Drain Current (VDS = 500V, VGS = 0V) Zero Gate Voltage Drain Current (VDS = 400V, VGS = 0V, TC = 125°C) Gate-Source Leakage Current (VGS = ±30V, VDS = 0V) Gate Threshold Voltage (VDS = VGS, ID = 2.5mA) CAUTION: These Devices are Sensitive to Electrostatic Discharge. Proper Handling Procedures Should Be Followed. APT Website - http://www.advancedpower.com DYNAMIC CHARACTERISTICS Symbol Ciss Coss Crss Qg Qgs Qgd td(on) tr td(off) tf Eon Eoff Eon Eoff Characteristic Input Capacitance Output Capacitance Reverse Transfer Capacitance Total Gate Charge 3 APT5010B2LL_LLL Test Conditions VGS = 0V VDS = 25V f = 1 MHz VGS = 10V VDD = 250V ID = 46A @ 25°C RESISTIVE SWITCHING VGS = 15V VDD = 250V ID = 46A @ 25°C RG = 0.6Ω 6 INDUCTIVE SWITCHING @ 25°C VDD = 333V, VGS = 15V ID = 46A, RG = 5Ω 6 INDUCTIVE SWITCHING @ 125°C VDD = 333V, VGS = 15V ID = 46A, RG = 5Ω MIN TYP MAX UNIT 4360 895 60 95 24 50 11 15 25 3 545 510 845 595 MIN TYP MAX UNIT Amps Volts ns µC V/ns nC pF Gate-Source Charge Gate-Drain ("Miller") Charge Turn-on Delay Time Rise Time Turn-off Delay Time Fall Time Turn-on Switching Energy Turn-off Switching Energy Turn-on Switching Energy Turn-off Switching Energy ns µJ SOURCE-DRAIN DIODE RATINGS AND CHARACTERISTICS Symbol IS ISM VSD t rr Q rr dv/ dt Characteristic / Test Conditions Continuous Source Current (Body Diode) Pulsed Source Current Diode Forward Voltage 1 2 46 184 1.3 608 11.0 8 MIN TYP MAX (Body Diode) (VGS = 0V, IS = - 46A) Reverse Recovery Time (IS = -46A, dl S /dt = 100A/µs) Reverse Recovery Charge (IS = -46A, dl S/dt = 100A/µs) Peak Diode Recovery d v/ dt 5 THERMAL CHARACTERISTICS Symbol RθJC RθJA Characteristic Junction to Case Junction to Ambient UNIT °C/W 0.25 40 1 Repetitive Rating: Pulse width limited by maximum junction temperature 2 Pulse Test: Pulse width < 380 µs, Duty Cycle < 2% 3 See MIL-STD-750 Method 3471 4 Starting Tj = +25°C, L = 1.51mH, RG = 25Ω, Peak IL = 46A 5 dv/dt numbers reflect the limitations of the test circuit rather than the device itself. IS ≤ -ID46A di/dt ≤ 700A/µs VR ≤ VDSS TJ ≤ 150°C 6 Eon includes diode reverse recovery. See figures 18, 20. APT Reserves the right to change, without notice, the specifications and information contained herein. 0.30 Z JC, THERMAL IMPEDANCE (°C/W) θ 0.25 0.20 0.9 0.7 0.5 0.3 0.1 0.05 Note: PDM t1 t2 0.15 9-2004 0.10 050-7011 Rev D 0.05 0 SINGLE PULSE Peak TJ = PDM x ZθJC + TC Duty Factor D = t1/t2 10-5 10-3 10-2 10-1 RECTANGULAR PULSE DURATION (SECONDS) FIGURE 1, MAXIMUM EFFECTIVE TRANSIENT THERMAL IMPEDANCE, JUNCTION-TO-CASE vs PULSE DURATION 10-4 1.0 Typical Performance Curves Junction temp. (°C) RC MODEL 120 100 80 60 40 APT5010B2LL_LLL 15 &10V 8V 7.5V 7V 0.0131 0.00266F 0.0789 Power (watts) 0.0811 0.00584F ID, DRAIN CURRENT (AMPERES) 6.5V 0.0796F 6V 20 0 5.5V 0.230 Case temperature. (°C) 0.460F FIGURE 2, TRANSIENT THERMAL IMPEDANCE MODEL 90 ID, DRAIN CURRENT (AMPERES) VDS> ID (ON) x RDS (ON)MAX. 250 µSEC. PULSE TEST @