APT6025SFLL

APT6025BFLL APT6025SFLL 600V 24A 0.250Ω BFLL D3PAK TO-247 POWER MOS 7 ® R FREDFET Power MOS 7 is a new generation of low loss, high voltage, N-Channel enhancement mode power MOSFETS. Both conduction and switching ® losses are addressed with Power MOS 7 by significantly lowering RDS(ON) ® and Qg. Power MOS 7 combines lower conduction and switching losses along with exceptionally fast switching speeds inherent with APT's patented metal gate structure. • Lower Input Capacitance • Lower Miller Capacitance • Lower Gate Charge, Qg MAXIMUM RATINGS Symbol VDSS ID IDM VGS VGSM PD TJ,TSTG TL IAR EAR EAS Parameter Drain-Source Voltage Continuous Drain Current @ TC = 25°C Pulsed Drain Current 1 SFLL • Increased Power Dissipation • Easier To Drive • TO-247 or Surface Mount D3PAK Package • FAST RECOVERY BODY DIODE D G S All Ratings: TC = 25°C unless otherwise specified. APT6025BFLL_SFLL UNIT Volts Amps 600 24 96 ±30 ±40 325 2.60 -55 to 150 300 24 30 4 Gate-Source Voltage Continuous Gate-Source Voltage Transient Total Power Dissipation @ TC = 25°C Linear Derating Factor Operating and Storage Junction Temperature Range Lead Temperature: 0.063" from Case for 10 Sec. Avalanche Current 1 Volts Watts W/°C °C Amps mJ (Repetitive and Non-Repetitive) 1 Repetitive Avalanche Energy Single Pulse Avalanche Energy 1300 STATIC ELECTRICAL CHARACTERISTICS Symbol BVDSS RDS(on) IDSS IGSS VGS(th) Characteristic / Test Conditions Drain-Source Breakdown Voltage (VGS = 0V, ID = 250µA) Drain-Source On-State Resistance 2 MIN TYP MAX UNIT Volts 600 0.250 250 1000 ±100 3 5 (VGS = 10V, ID = 12A) Ohms µA nA Volts 9-2004 050-7066 Rev B Zero Gate Voltage Drain Current (VDS = 600V, VGS = 0V) Zero Gate Voltage Drain Current (VDS = 480V, VGS = 0V, TC = 125°C) Gate-Source Leakage Current (VGS = ±30V, VDS = 0V) Gate Threshold Voltage (VDS = VGS, ID = 1mA) CAUTION: These Devices are Sensitive to Electrostatic Discharge. Proper Handling Procedures Should Be Followed. APT Website - http://www.advancedpower.com DYNAMIC CHARACTERISTICS Symbol C iss Coss C rss Qg Qgs Qgd td(on) tr td(off) tf Eon Eoff Eon Eoff Symbol IS ISM VSD dv/ dt APT6025BFLL_SFLL Test Conditions VGS = 0V VDS = 25V f = 1 MHz VGS = 10V VDD = 300V ID = 24A @ 25°C RESISTIVE SWITCHING VGS = 15V VDD = 300V ID = 24A @ 25°C 6 INDUCTIVE SWITCHING @ 25°C VDD = 400V, VGS = 15V INDUCTIVE SWITCHING @ 125°C VDD = 400V, VGS = 15V ID = 24A, RG = 5Ω ID = 24A, RG = 5Ω RG = 1.6Ω Characteristic Input Capacitance Output Capacitance Reverse Transfer Capacitance Total Gate Charge 3 MIN TYP MAX UNIT pF 2910 535 55 65 15 34 18 19 30 18 280 110 420 140 MIN TYP MAX Gate-Source Charge Gate-Drain ("Miller ") Charge Turn-on Delay Time Rise Time Turn-off Delay Time Fall Time Turn-on Switching Energy Turn-off Switching Energy Turn-on Switching Energy Turn-off Switching Energy Characteristic / Test Conditions Continuous Source Current (Body Diode) Pulsed Source Current Diode Forward Voltage Peak Diode Recovery 1 2 dt 6 nC ns µJ SOURCE-DRAIN DIODE RATINGS AND CHARACTERISTICS UNIT Amps Volts V/ns ns µC Amps 24 96 1.3 Tj = 25°C Tj = 125°C Tj = 25°C Tj = 125°C Tj = 25°C Tj = 125°C MIN (Body Diode) (VGS = 0V, IS = -24A) 5 d v/ t rr Q rr IRRM Reverse Recovery Time (IS = -24A, di/dt = 100A/µs) Reverse Recovery Charge (IS = -24A, di/dt = 100A/µs) Peak Recovery Current (IS = -24A, di/dt = 100A/µs) Characteristic Junction to Case Junction to Ambient 15 250 525 2.34 5.22 12 17 TYP MAX THERMAL CHARACTERISTICS Symbol RθJC RθJA UNIT °C/W 0.38 40 1 Repetitive Rating: Pulse width limited by maximum junction temperature 2 Pulse Test: Pulse width < 380 µs, Duty Cycle < 2% 3 See MIL-STD-750 Method 3471 0.40 Z JC, THERMAL IMPEDANCE (°C/W) θ 4 Starting Tj = +25°C, L = 4.51mH, RG = 25Ω, Peak IL = 24A 5 dv/dt numbers reflect the limitations of the test circuit rather than the device itself. IS ≤ -ID24A di/dt ≤ 700A/µs VR ≤ VDSS TJ ≤ 150°C 6 Eon includes diode reverse recovery. See figures 18, 20. APT Reserves the right to change, without notice, the specifications and information contained herein. 0.35 0.30 0.25 0.20 0.15 0.9 0.7 0.5 Note: PDM t1 t2 9-2004 0.3 0.10 0.05 0 10-5 0.1 0.05 050-7066 Rev B Peak TJ = PDM x ZθJC + TC Duty Factor D = t1/t2 SINGLE PULSE 10-4 10-3 10-2 10-1 RECTANGULAR PULSE DURATION (SECONDS) FIGURE 1, MAXIMUM EFFECTIVE TRANSIENT THERMAL IMPEDANCE, JUNCTION-TO-CASE vs PULSE DURATION 1.0 Typical Performance Curves Junction temp. (°C) RC MODEL 80 70 ID, DRAIN CURRENT (AMPERES) 0.00401F APT6025BFLL_SFLL VGS =15 &10V 8V 7V 6.5 6V 5.5V 5V 0.0175 60 50 40 30 20 10 0 Power (watts) 0.143 0.00641F 0.219 Case temperature. (°C) 0.158F RDS(ON), DRAIN-TO-SOURCE ON RESISTANCE FIGURE 2, TRANSIENT THERMAL IMPEDANCE MODEL 80 70 ID, DRAIN CURRENT (AMPERES) VDS> ID (ON) x RDS(ON) MAX. 250µSEC. PULSE TEST @