APT75GN120B2G

TYPICAL PERFORMANCE CURVES ® 1200V APT75GN120B2_L(G) APT75GN120B2 APT75GN120L APT75GN120B2G* APT75GN120LG* *G Denotes RoHS Compliant, Pb Free Terminal Finish. Utilizing the latest Field Stop and Trench Gate technologies, these IGBT's have ultra low VCE(ON) and are ideal for low frequency applications that require absolute minimum conduction loss. Easy paralleling is a result of very tight parameter distribution and a slightly positive VCE(ON) temperature coefficient. A built-in gate resistor ensures extremely reliable operation, even in the event of a short circuit fault. Low gate charge simplifies gate drive design and minimizes losses. (B2) T-Max® TO-264 (L) • 1200V Field Stop • Trench Gate: Low VCE(on) • Easy Paralleling • Intergrated Gate Resistor: Low EMI, High Reliability C G E Applications: Welding, Inductive Heating, Solar Inverters, SMPS, Motor drives, UPS MAXIMUM RATINGS Symbol VCES VGE I C1 I C2 I CM SSOA PD TJ,TSTG TL Parameter Collector-Emitter Voltage Gate-Emitter Voltage Continuous Collector Current 8 All Ratings: TC = 25°C unless otherwise specified. APT75GN120B2_L(G) UNIT Volts 1200 ±30 @ TC = 25°C 200 99 225 225A @ 1200V 833 -55 to 150 300 Watts °C Amps Continuous Collector Current @ TC = 110°C Pulsed Collector Current 1 @ TC = 150°C Switching Safe Operating Area @ TJ = 150°C Total Power Dissipation Operating and Storage Junction Temperature Range Max. Lead Temp. for Soldering: 0.063" from Case for 10 Sec. STATIC ELECTRICAL CHARACTERISTICS Symbol V(BR)CES VGE(TH) VCE(ON) Characteristic / Test Conditions Collector-Emitter Breakdown Voltage (VGE = 0V, I C = 3mA) Gate Threshold Voltage (VCE = VGE, I C = 3mA, Tj = 25°C) MIN TYP MAX Units 1200 5.0 1.4 2 2 5.8 1.7 2.0 6.5 2.1 100 TBD 600 Collector-Emitter On Voltage (VGE = 15V, I C = 75A, Tj = 25°C) Collector-Emitter On Voltage (VGE = 15V, I C = 75A, Tj = 125°C) Collector Cut-off Current (VCE = 1200V, VGE = 0V, Tj = 25°C) Volts I CES I GES RG(int) Gate-Emitter Leakage Current (VGE = ±20V) Intergrated Gate Resistor nA Ω CAUTION: These Devices are Sensitive to Electrostatic Discharge. Proper Handling Procedures Should Be Followed. APT Website - http://www.advancedpower.com 050-7607 Rev C 10 10-2005 Collector Cut-off Current (VCE = 1200V, VGE = 0V, Tj = 125°C) µA DYNAMIC CHARACTERISTICS Symbol Cies Coes Cres VGEP Qg Qge Qgc SSOA td(on) tr td(off) tf Eon1 Eon2 Eoff td(on) tr td(off) tf Eon1 Eon2 Eoff Characteristic Input Capacitance Output Capacitance Reverse Transfer Capacitance Gate-to-Emitter Plateau Voltage Total Gate Charge 3 APT75GN120B2_L(G) Test Conditions Capacitance VGE = 0V, VCE = 25V f = 1 MHz Gate Charge VCE = 600V I C = 75A TJ = 150°C, R G = 4.3Ω 7, VGE = 15V, L = 100µH,VCE = 1200V Inductive Switching (25°C) VCC = 800V VGE = 15V I C = 75A VGE = 15V MIN TYP MAX UNIT pF V nC 4800 275 210 9.0 425 30 245 225 60 41 620 110 8045 9620 7640 60 41 725 200 8620 13000 11400 µJ ns ns A Gate-Emitter Charge Gate-Collector ("Miller ") Charge Switching Safe Operating Area Turn-on Delay Time Current Rise Time Turn-off Delay Time Current Fall Time Turn-on Switching Energy Turn-off Switching Energy Turn-on Delay Time Current Rise Time Turn-off Delay Time Current Fall Time Turn-on Switching Energy Turn-off Switching Energy 44 55 4 5 RG = 1.0Ω 7 TJ = +25°C Turn-on Switching Energy (Diode) 6 µJ Inductive Switching (125°C) VCC = 800V VGE = 15V I C = 75A Turn-on Switching Energy (Diode) 66 TJ = +125°C RG = 1.0Ω 7 THERMAL AND MECHANICAL CHARACTERISTICS Symbol RθJC RθJC WT Characteristic Junction to Case (IGBT) Junction to Case (DIODE) Package Weight MIN TYP MAX UNIT °C/W gm .15 N/A 5.9 1 Repetitive Rating: Pulse width limited by maximum junction temperature. 2 For Combi devices, Ices includes both IGBT and FRED leakages 3 See MIL-STD-750 Method 3471. 4 Eon1 is the clamped inductive turn-on energy of the IGBT only, without the effect of a commutating diode reverse recovery current adding to the IGBT turn-on loss. Tested in inductive switching test circuit shown in figure 21, but with a Silicon Carbide diode. 5 Eon2 is the clamped inductive turn-on energy that includes a commutating diode reverse recovery current in the IGBT turn-on switching loss. (See Figures 21, 22.) 10-2005 Rev C 6 Eoff is the clamped inductive turn-off energy measured in accordance with JEDEC standard JESD24-1. (See Figures 21, 23.) 7 RG is external gate resistance, not including RG(int) nor gate driver impedance. (MIC4452) 8 Current limited by lead temperature. APT Reserves the right to change, without notice, the specifications and information contained herein. 050-7607 TYPICAL PERFORMANCE CURVES 160 140 IC, COLLECTOR CURRENT (A) 120 100 80 60 40 20 0 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 VCE, COLLECTER-TO-EMITTER VOLTAGE (V) 250µs PULSE TEST