APT8043SFLL

800V APT8043BFLL APT8043SFLL BFLL 20A 0.430Ω POWER MOS 7 ® R FREDFET Power MOS 7 is a new generation of low loss, high voltage, N-Channel enhancement mode power MOSFETS. Both conduction and switching ® losses are addressed with Power MOS 7 by significantly lowering RDS(ON) ® and Qg. Power MOS 7 combines lower conduction and switching losses along with exceptionally fast switching speeds inherent with APT's patented metal gate structure. • Lower Input Capacitance • Lower Miller Capacitance • Lower Gate Charge, Qg MAXIMUM RATINGS Symbol VDSS ID IDM VGS VGSM PD TJ,TSTG TL IAR EAR EAS Parameter Drain-Source Voltage Continuous Drain Current @ TC = 25°C Pulsed Drain Current 1 D3PAK TO-247 SFLL • Increased Power Dissipation • Easier To Drive • TO-247 or Surface Mount D3PAK Package • FAST RECOVERY BODY DIODE D G S All Ratings: TC = 25°C unless otherwise specified. APT8043BFLL_SFLL UNIT Volts Amps 800 20 80 ±30 ±40 403 3.23 -55 to 150 300 20 30 4 Gate-Source Voltage Continuous Gate-Source Voltage Transient Total Power Dissipation @ TC = 25°C Linear Derating Factor Operating and Storage Junction Temperature Range Lead Temperature: 0.063" from Case for 10 Sec. Avalanche Current 1 Volts Watts W/°C °C Amps mJ (Repetitive and Non-Repetitive) 1 Repetitive Avalanche Energy Single Pulse Avalanche Energy 1300 STATIC ELECTRICAL CHARACTERISTICS Symbol BVDSS RDS(on) IDSS IGSS VGS(th) Characteristic / Test Conditions Drain-Source Breakdown Voltage (VGS = 0V, ID = 250µA) Drain-Source On-State Resistance 2 MIN TYP MAX UNIT Volts 800 0.430 250 1000 ±100 3 5 (VGS = 10V, ID = 10A) Ohms µA nA Volts 7-2004 050-7077 Rev B Zero Gate Voltage Drain Current (VDS = 800V, VGS = 0V) Zero Gate Voltage Drain Current (VDS = 640V, VGS = 0V, TC = 125°C) Gate-Source Leakage Current (VGS = ±30V, VDS = 0V) Gate Threshold Voltage (VDS = VGS, ID = 1mA) CAUTION: These Devices are Sensitive to Electrostatic Discharge. Proper Handling Procedures Should Be Followed. APT Website - http://www.advancedpower.com DYNAMIC CHARACTERISTICS Symbol Ciss Coss Crss Qg Qgs Qgd td(on) tr td(off) tf Eon Eoff Eon Eoff Symbol IS ISM VSD dv/ dt APT8043BFLL_SFLL Test Conditions VGS = 0V VDS = 25V f = 1 MHz VGS = 10V VDD = 400V ID = 20A @ 25°C RESISTIVE SWITCHING VGS = 15V VDD = 400V ID = 20A @ 25°C 6 INDUCTIVE SWITCHING @ 25°C VDD = 533V, VGS = 15V INDUCTIVE SWITCHING @ 125°C VDD = 533V VGS = 15V ID = 20A, RG = 5Ω ID = 20A, RG = 5Ω RG = 1.6Ω Characteristic Input Capacitance Output Capacitance Reverse Transfer Capacitance Total Gate Charge 3 MIN TYP MAX UNIT pF 2500 485 80 85 13 55 9 5 25 5 300 130 555 170 MIN TYP MAX Gate-Source Charge Gate-Drain ("Miller") Charge Turn-on Delay Time Rise Time Turn-off Delay Time Fall Time Turn-on Switching Energy Turn-off Switching Energy Turn-on Switching Energy Turn-off Switching Energy Characteristic / Test Conditions Continuous Source Current (Body Diode) Pulsed Source Current Diode Forward Voltage Peak Diode Recovery 1 2 6 nC ns µJ SOURCE-DRAIN DIODE RATINGS AND CHARACTERISTICS UNIT Amps Volts V/ns ns µC Amps 20 80 1.3 18 Tj = 25°C Tj = 125°C Tj = 25°C Tj = 125°C Tj = 25°C Tj = 125°C MIN (Body Diode) (VGS = 0V, IS = -20A) d v/ 5 dt t rr Q rr IRRM Reverse Recovery Time (IS = -20A, di/dt = 100A/µs) Reverse Recovery Charge (IS = -20A, di/dt = 100A/µs) Peak Recovery Current (IS = -20A, di/dt = 100A/µs) Characteristic Junction to Case Junction to Ambient 200 400 0.91 3.5 9 14 TYP MAX THERMAL CHARACTERISTICS Symbol RθJC RθJA UNIT °C/W 0.31 40 1 Repetitive Rating: Pulse width limited by maximum junction temperature 2 Pulse Test: Pulse width < 380 µs, Duty Cycle < 2% 3 See MIL-STD-750 Method 3471 0.35 Z JC, THERMAL IMPEDANCE (°C/W) θ 4 Starting Tj = +25°C, L = 6.50mH, RG = 25Ω, Peak IL = 20A 5 dv/dt numbers reflect the limitations of the test circuit rather than the device itself. IS ≤ -ID20A di/dt ≤ 700A/µs VR ≤ 800 TJ ≤ 150°C 6 Eon includes diode reverse recovery. See figures 18, 20. APT Reserves the right to change, without notice, the specifications and information contained herein. 0.30 0.25 0.9 0.7 0.20 0.15 0.10 0.05 0 0.5 Note: PDM t1 t2 Peak TJ = PDM x ZθJC + TC Duty Factor D = t1/t2 7-2004 0.3 SINGLE PULSE 050-7077 Rev B 0.1 0.05 10-5 10-4 10-1 RECTANGULAR PULSE DURATION (SECONDS) FIGURE 1, MAXIMUM EFFECTIVE TRANSIENT THERMAL IMPEDANCE, JUNCTION-TO-CASE vs PULSE DURATION 10-3 10-2 1.0 Typical Performance Curves Junction temp. (°C) RC MODEL 50 VGS =15 &10 V 7.5V 30 7V 20 6.5V APT8043BFLL_SFLL 8V ID, DRAIN CURRENT (AMPERES) 40 0.0258 0.00295F Power (watts) 0.107 0.0114F 0.177 Case temperature. (°C) 0.174F 10 6V 5.5V RDS(ON), DRAIN-TO-SOURCE ON RESISTANCE FIGURE 2, TRANSIENT THERMAL IMPEDANCE MODEL 80 70 60 50 40 30 20 10 0 TJ = +125°C TJ = -55°C TJ = +25°C 0 2 4 6 8 10 VGS, GATE-TO-SOURCE VOLTAGE (VOLTS) FIGURE 4, TRANSFER CHARACTERISTICS VDS> ID (ON) x RDS (ON)MAX. 250µSEC. PULSE TEST @