APTM50AM25FT

APTM50AM25FT Phase leg MOSFET Power Module VDSS = 500V RDSon = 25mΩ max @ Tj = 25°C ID = 149A @ Tc = 25°C Application • • • • Welding converters Switched Mode Power Supplies Uninterruptible Power Supplies Motor control Features • Power MOS V® FREDFETs - Low RDSon - Low input and Miller capacitance - Low gate charge - Fast intrinsic diode - Avalanche energy rated - Very rugged Kelvin source for easy drive Kelvin Drain for VDS monitoring Very low stray inductance - Symmetrical design - M5 power connectors Internal thermistor for temperature monitoring High level of integration • • • DK1 NC G1 SK1 NC SK2 G2 NC DK2 NC NTC1 NTC2 • • Benefits • • • • OUT 0/VBUS VBUS Outstanding performance at high frequency operation Direct mounting to heatsink (isolated package) Low junction to case thermal resistance Solderable terminals for signal and M5 for power for easy PCB mounting Max ratings 500 149 111 450 ±30 25 1250 149 30 1300 Unit V A V mΩ W A mJ Absolute maximum ratings Symbol VDSS ID IDM VGS RDSon PD IAR EAR EAS Parameter Drain - Source Breakdown Voltage Continuous Drain Current Tc = 25°C Tc = 80°C These Devices are sensitive to Electrostatic Discharge. Proper Handing Procedures Should Be Followed. APT website – http://www.advancedpower.com 1-3 APTM50AM25FT – Rev 0 Pulsed Drain current Gate - Source Voltage Drain - Source ON Resistance Maximum Power Dissipation Avalanche current (repetitive and non repetitive) Repetitive Avalanche Energy Single Pulse Avalanche Energy Tc = 25°C June, 2003 APTM50AM25FT Electrical Characteristics Symbol Characteristic BVDSS Drain - Source Breakdown Voltage IDSS RDS(on) VGS(th) IGSS Zero Gate Voltage Drain Current Drain – Source on Resistance Gate Threshold Voltage Gate – Source Leakage Current Test Conditions VGS = 0V, ID = 1mA VGS = 0V,VDS = 500V VGS = 0V,VDS = 400V All ratings @ Tj = 25°C unless otherwise specified Min 500 Typ Max Unit V µA mΩ V nA Tj = 25°C Tj = 125°C 2 1000 2500 25 4 ±250 VGS = 10V, ID = 74.5A VGS = VDS, ID = 8mA VGS = ±30 V, VDS = 0V Dynamic Characteristics Symbol Ciss Coss Crss Qg Qgs Qgd Td(on) Tr Td(off) Tf Characteristic Input Capacitance Output Capacitance Reverse Transfer Capacitance Total gate Charge Gate – Source Charge Gate – Drain Charge Turn-on Delay Time Rise Time Turn-off Delay Time Fall Time Test Conditions VGS = 0V VDS = 25V f = 1MHz VGS = 10V VBus = 250V ID = 149A Resistive Switching VGS = 15V VBus = 250V ID = 149A RG = 0.22 Ω Min Typ 29.6 4.1 1.6 1200 200 560 15 20 50 10 Max Unit nF nC ns Source - Drain diode ratings and characteristics Symbol Characteristic IS Continuous Source current (Body diode) VSD Diode Forward Voltage dv/dt Peak Diode Recovery trr Qrr Reverse Recovery Time Reverse Recovery Charge Test Conditions Min Typ Tc = 25°C Tc = 80°C VGS = 0V, IS = - 149A IS = - 149A VR = 250V diS/dt = 800A/µs IS = - 149A VR = 250V diS/dt = 800A/µs Tj = 25°C Tj = 125°C Tj = 25°C Tj = 125°C 10.4 36 Max 149 111 1.3 5 250 500 Unit A V V/ns ns µC dv/dt numbers reflect the limitations of the circuit rather than the device itself. IS ≤ - 149A di/dt ≤ 700A/µs VR ≤ VDSS Tj ≤ 150°C APT website – http://www.advancedpower.com 2-3 APTM50AM25FT – Rev 0 June, 2003 APTM50AM25FT Thermal and package characteristics Symbol Characteristic RthJC Junction to Case RMS Isolation Voltage, any terminal to case VISOL t =1 min, I isol