NSL-32SR2S

Optocoupler NSL 32SR2(Sorted) Precision – Control – Results WWW.LUNAINC.COM   5.7 min. 25.4 min. Photocell 2.54 Anode lead 0.25 x 0.51 + + Photocell LED     - -  0.45-0.56 cell leads  6.0 - 6.5   3.30 Color dot 5.72 - 6.22 Cathode lead 0.25 x 0.64 Dimensions in mm. Lead spacing tolerance: +/-0.13 DESCRIPTION  FEATURES  This optocoupler consists of an LED input optically coupled to a photocell.  The photocell resistance is high when the LED current is “off” and low resistance when the LED current is “on”.        Circuit Schematic Compact, moisture resistant package  Low LED current  Very low “on” resistance  Passive resistance output  Low distortion  RELIABILITY  APPLICATIONS  Contact Luna for recommendations on specific test conditions and  procedures.   Isolation Voltage Industrial      ABSOLUTE MAXIMUM RATINGS  SYMBOL LED MIN MAX UNITS - - 2000 V Ta = 23°C UNLESS OTHERWISE NOTED Operating Temperature -40 to +75 °C Non condensing Soldering Temperature -40 - +75 °C - Soldering Temperature - - +260 °C >2 mm from case for < 5 sec. NOTE: 1.Measure after 1 minute ON @ IF = 20mA and followed by 10 sec OFF 2. Print “NSL-32SR2” followed by a letter A to G and date code YYWW 3. Package in ranges individual ranges not available separately. Range distribution is not guaranteed   Information in this technical datasheet is believed to be correct and reliable. However, no responsibility is assumed for possible inaccuracies or omission. Specifications are subject to change without notice.  Page 1/3  REV 03-28-16 © 2016 Luna Optoelectronics. All rights reserved. Luna Optoelectronics, 1240 Avenida Acaso, Camarillo CA 93012 • Phone (805) 987-0146 • Fax (805) 484-9935   Optocoupler NSL 32SR2(Sorted) Precision – Control – Results WWW.LUNAINC.COM   Ta = 23°C UNLESS NOTED OTHERWISE OPTO-ELECTRICAL PARAMETERS  TEST CONDITIONS  PARAMETER MIN  TYP  MAX  UNITS  LED Forward Current - - - 25 mA Forward Voltage If = 20 mA - - 2.5 V Reverse Current VR = 4V - - 10 µA Maximum Cell Voltage (Peak AC or DC) - - 60 V Power Dissipation Derate linearly to 0 at 75°C - - 50 mW On Resistance If=20 mA - R2A If=1 mA (guaranteed ±1 range) 100 R2B - R2C CELL COUPLED 124 Ω Ω 124 150 Ω - 150 177 Ω R2D - 177 205 Ω R2E - 205 234 Ω R2F - 234 266 Ω - 266 300 Ω R2G Off Resistance 1 40 - 10 sec after If = 0 mA 1 5 - MΩ Rise Time Time to reach 63% of final conductive @ If = 16mA - 5 - m sec Decay Time Time to reach 100KΩ from removal of If = 16mA - 80 - msec Cell Temp. Coefficient If > 5mA - 0.7 - %/°C NOTE: 1.Measure after 1 minute ON @ IF = 20mA and followed by 10 sec OFF 2. Print “NSL-32SR2” followed by a letter A to G and date code YYWW 3. Package in ranges individual ranges not available separately. Range distribution is not guaranteed   Information in this technical datasheet is believed to be correct and reliable. However, no responsibility is assumed for possible inaccuracies or omission. Specifications are subject to change without notice.  Page 2/3  REV 03-28-16 © 2016 Luna Optoelectronics. All rights reserved. Luna Optoelectronics, 1240 Avenida Acaso, Camarillo CA 93012 • Phone (805) 987-0146 • Fax (805) 484-9935   Optocoupler NSL 32SR2(Sorted) Precision – Control – Results WWW.LUNAINC.COM   TYPICAL PERFORMANCE Photocell Resistance vs. LED Current   Resistance () 10000 1000 100 10 0.01 0.1 1 10 100 Current (mA)     Information in this technical datasheet is believed to be correct and reliable. However, no responsibility is assumed for possible inaccuracies or omission. Specifications are subject to change without notice.  Page 3/3  REV 03-28-16 © 2016 Luna Optoelectronics. All rights reserved. Luna Optoelectronics, 1240 Avenida Acaso, Camarillo CA 93012 • Phone (805) 987-0146 • Fax (805) 484-9935