96FD-M128-PLG1

PX-xxxG7Me Model PX-64G7Me PX-128G7Me PX-256G7Me PX-512G7Me mSATA (JEDEC MO-300) SATA 6.0 Gb/s Solid State Drive Product Specification Manual Rev.: Revision Date: Rev1.0 2014/04/23 LITE-ON IT CORPORATION Document History Revision Date Rev 1.0 2014/04/23 Page 2 of 23 Changes First Release Prodcut Specification Copyright 2014 LITE-ON IT CORPORATION Disclaimer The information in this document is subject to change without prior notice in order to improve reliability, design, and function and does not represent a commitment on the part of the manufacturer. In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use the product or documentation, even if advised of the possibility of such damages. This document contains proprietary information protected by copyright. All rights are reserved. No part of this datasheet may be reproduced by any mechanical, electronic, or other means in any form without prior written permission of LITEON IT Corporation. Product Specification Page 3 of 23 Table of Contents 1 Introduction ........................................................................ 5 1.1 1.2 1.3 1.4 1.5 1.6 Overview : ................................................................................................. 5 Product Specification .................................................................................... 5 Functional Block Diagram ............................................................................. 10 Mechanical Drawing: ................................................................................... 10 Architecture ............................................................................................. 11 DEVSLP power mode ................................................................................. 11 2 Pin Locations and Signal Descriptions ...................................... 12 2.1 2.2 Pin Locations............................................................................................ 12 Signal Descriptions..................................................................................... 12 3 ATA Command Sets ............................................................. 14 3.1 3.2 3.3 ATA Command ......................................................................................... 14 Power Management Command Set ................................................................. 17 Security Mode Feature Set ........................................................................... 18 3.4 3.5 3.6 3.7 3.8 SMART Command Set ................................................................................ 18 Host Protected Area Command Set ................................................................. 19 48-Bit Address Command Set ........................................................................ 19 Device Configuration Overlay Command Set ...................................................... 19 General Purpose log Command Set ................................................................. 19 4 SATA Command Sets ........................................................... 20 4.1 SATA Command........................................................................................ 20 5 References ........................................................................ 21 6 Terms and Acronyms ........................................................... 22 Page 4 of 23 Prodcut Specification 1 Introduction 1.1 Overview : The PX-xxxG7Me MLC series mSATA 6 Gb/s Solid State Drive (mSATA SSD) delivers leading performance in an industry standard JEDEC MO-300 form factor while simultaneously improving system responsiveness for mobile applications over standard rotating drive media or hard disk drives. By combining leading NAND flash memory technology with our innovative high performance firmware, LITEON IT delivers a SSD for native Serial Advanced Technology Attachment (SATA) hard disk drive drop-in replacement with enhanced performance, reliability, ruggedness and power savings. Since there are no rotating platters, moving heads, fragile actuators, or unnecessary delays due to spin-up time or positional seek time that can slow down the storage subsystem, significant I/O and throughput performance improvement is achieved as compared to rotating media or hard disk drives. This document describes the specifications of the PX-xxxG7Me MLC series mSATA SSD in JEDEC MO-300 form factors. The PX-xxxG7Me mSATA SSD primarily targets mSATA based laptop PCs, highly rugged mobile client devices, as well as thin and light mini/sub-notebooks. Key attributes include high performance, low power, increased system responsiveness, high reliability, and enhanced ruggedness as compared to standard mobile mSATA hard drives. The PX-xxxG7Me mSATA SSD is available in JEDEC MO-300 form factor that are electrically, mechanically, and software compatible with existing JEDEC MO-300 Serial ATA slots. Our flexible design allows interchangeability with existing mobile hard drives based on the mSATA interface standard. 1.2 Product Specification 1.2.1. Form Factor: JEDEC MO-300 mSATA SSD form factor 1.2.2. Capacity: Table 1 User Addressable Sectors Model Unformatted capacity Total user addressable sectors in LBA mode PX-64G7Me PX-128G7Me PX-256G7Me PX-512G7Me 64GB 128GB 256GB 512GB 125,045,424 250,069,680 500,118,192 1,000,215,216 Notes: 1. 2. 1GB=1,000,000,000 bytes and not all of the memory can be used for storage. 1 Sector = 512 bytes 1.2.3. Flash: Multi-Level Cell (MLC) component with Toggle-Mode Product Specification Page 5 of 23 1.2.4. Band Performance Table 2 Maximum Sustained Read and Write Bandwidth Capacity 64 GB 128 GB 256 GB 512 GB Access Type MB/s Sequential Read Sequential Write Sequential Read Sequential Write Sequential Read Sequential Write Sequential Read Sequential Write Up to 520 Up to 160 Up to 520 Up to 320 Up to 510 Up to 440 Up to 510 Up to 440 Notes: 1. 2. Performance measured using CrystalDiskMark 1 MB/sec = 1,048,576 bytes/sec is used in measuring sequential performance. If 1 MB/sec = 1,000,000 bytes/sec is used, performance values become 4.85% higher. Test platform: ASUS P8P67 PRO (Windows 7 x64) Test by secondary drive (data drive) under SATA 6Gb/s. 3. 4. 1.2.5. Read and Write IOPS (IOMETER) Table 3 Random Read/Write Input/Output Operations per Second Capacity 64GB 128GB 256GB 512GB Access Type IOPS 4K Random Read 4K Random Write 4K Random Read 4K Random Write 4K Random Read 4K Random Write 4K Random Read 4K Random Write 85,000 41,000 94,000 75,000 94,000 80,000 94,000 80,000 Notes: 1. 2. 3. 4. Performance measured using IOMETER with queue depth set to 32, Crystal Disk Mark QD32 Write cache enabled. Test platform: ASUS P8P67 PRO (Windows 7 x64) Test by secondary drive (data drive) under SATA 6Gb/s. 1.2.6. Ready Time Table 4 Latency Specifications Type Average Latency Power on to Ready Resume from DEVSLP 300ms 100ms Notes: 1. Device measured form power-on to ready to receive first Media command 2. Power On To Ready time assumes drive have normal shutdown process which have STANDBY IMMEDIATE command. Time varies if shutdown is not preceded by Page 6 of 23 Prodcut Specification 1.2.7. Power Management -- SATA interface power management 1.2.8. Power Consumption Table 5 Operating Voltage Capacity 64GB 128GB 256GB 512GB Description Operating voltage for 3.3V (+/- 5%) Operating voltage for 3.3V (+/- 5%) Operating voltage for 3.3V (+/- 5%) Operating voltage for 3.3V (+/- 5%) Min 3.135 3.135 3.135 3.135 Max 3.465 3.465 3.465 3.465 Unit V V V V Table 6 Power Consumption (MobileMark) Capacity Mode Max Unit 64GB 128GB 256GB 512GB DIPM Enable DIPM Enable DIPM Enable DIPM Enable 0.25 0.25 0.25 0.25 W W W W Table 7 DEVSLP Mode Power Consumption Capacity Mode Max Unit 64GB 128GB 256GB 512GB DEVSLP DEVSLP DEVSLP DEVSLP 2 2 2 2 mW mW mW mW 1.2.9. Temperature Table 8 Temperature Relative Specifications Environment Ambient Temperature Humidity Mode Operating Non-operating Operation Non-operation Min 0 -40 5 5 Max 70 85 95 95 Unit °C °C % % Note: Measured without condensation 1.2.10. Compatibility -- SATA Revision 3.0 compliant Compatible with SATA 1.5Gb/s, 3.0Gb/s & 6.0Gb/s interface rates -- ATA/ATAPI- 8 compliant -- SSD enhanced SMART ATA feature set -- Native Command Queuing (NCQ) command set -- TRIM supported Product Specification Page 7 of 23 1.2.11. Certifications Table 9 Device Certifications Certification Description Indicates conformity with the essential health and safety CE compliant requirements set out in European Directives Low voltage Directive and EMC Directive Underwriters Laboratories, Inc. Component Recognition UL certified UL60950-1 Compliance to the Taiwan EMC standard “Limits and methods of BSMI Radio Disturbance Characteristics of Information Technology Equipment, CNS 13438 Class B” Microsoft WHQL Microsoft Windows Hardware Quality Labs RoHS compliant Restriction of Hazardous Substance Directive 1.2.12. Reliability Table 10 Reliability specifications Parameter Value Mean Time between Failure (MTBF) Power on/off cycles > 1,500,000 hours 50000 cycles Notes: 1. 2. MTBF is calculated based on a Part Stress Analysis. It assumes nominal voltage. With all other parameters within specified range. Power on/off cycles is defined as power being removed from the drive, and the restored. Most host systems remove power from the drive when entering suspend and hibernate as well as on a system shutdown. 1.2.13. Shock and Vibration Table 11 Shock and Vibration Item Shock Vibration Mode Timing/Frequency operating operating Non-operating Non-operating Operation Non-operation At 1 msec half-sine At 2 msec half-sine At 1 msec half-sine At 2 msec half-sine 7~800 Hz 7~800 Hz Max 1500G 1000G 1500G 1000G 2.17Grms 3.08Grms Notes: 1. Shock specifications assume that the SSD is mounted securely with the input vibration applied to the drive mounting screws. Stimulus may be applied in the X, Y or Z axis 2. Vibration specifications assume that the SSD is mounted securely with the input vibration applied to the drive mounting screws. Stimulus may be applied in the X, Y or Z axis. The measured specification is in root mean squared form. Page 8 of 23 Prodcut Specification 1.2.14. Electromagnetic Immunity Electromagnetic Immunity tests assume the SSD is properly installed in the representative host system. The drive operates properly without errors degradation in performance when subjected to radio frequency (RF) environments defined in the following table. Table 12 Radio Frequency Specifications Test Electrostatic discharge Electrostatic discharge Electrostatic discharge Radiated RF immunity Electrical fast transient Description Contact ±4KV Air: ±8KV Contact ±6KV Air: ±12KV Contact ±8KV Air: ±15KV 80~1000MHz, 3V/m, 80% AM with 1 KHz sine 900 MHz, 3 V/m, 50% pulse modulation at 200Hz ±1KV on AC mains ±0.5KV on external I/O ±1KV differential ±2KV common, AC mains 150KHz~80 MHz, 3 Vrms, 80% AM Conducted RF immunity with 1KHz sine Power frequency 50Hz, 1A/m (r.m.s.) magnetic field Surge immunity Performance criteria A B C Reference standard IEC 61000-4-2:2008 IEC 61000-4-2:2008 IEC 61000-4-2:2008 A IEC 61000-4-3:2008 B IEC 61000-4-4:2004 +Corr.1:2006 +Corr.2:2007 B IEC 61000-4-5:2005 A IEC 61000-4-6:2008 A IEC 61000-4-6:2008 Notes: 1. 2. 3. 4. Performance criterion A = The device shall continue to operate as intended, i.e., normal unit operation with no degradation of performance. Performance criterion B = The device shall continue to operate as intended after completion of test, however, during the test, some degradation of performance is allowed as long as there is no data loss operator intervention to restore device function. Performance criterion C = Temporary loss of function is allowed. Operator intervention is acceptable to restore device function. Contact electrostatic discharge is applied to drive enclosure. 1.2.15. Weight: 10 g Max. 1.2.16. Dimension: 50.8 mm x 29.8mm x 3.6 mm (L x W x H) Product Specification Page 9 of 23 1.3 Functional Block Diagram DDR3 DRAM SATA Host Interface 1.4 Flash Memory Controller NAND Flash Array Mechanical Drawing: Dimension: 50.8 mm x 29.8mm x 3.6 mm (L x W x H) Page 10 of 23 Prodcut Specification 1.5 Architecture The PX-xxxG7Me MLC series mSATA 6Gb/s Solid State Drive (SSD) utilizes a cost effective system-on-chip (SoC) design to provide a full 6Gb/s bandwidth with the host while managing multiple flash memory devices on multiple channels internally. 1.6 DEVSLP power mode LiteON SSD support DEVSLP power mode. After power up, and enabled by a SET FEATURES command from the host, device will enter DEVSLP mode from any state after receive HW DEVSLP signal pin trigger. And return to Reset state after HW DEVSLP signal pin negated. Product Specification Page 11 of 23 2 Pin Locations and Signal Descriptions 2.1 Pin Locations The data and power connector pin locations of the PX-xxxG7Me series mSATA 6 Gb/s SSD are as shown below. 2.2 Signal Descriptions Table 13 Connector Pin Definitions Name P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 P13 P14 Page 12 of 23 Type Reserved +3.3V Reserved GND Reserved +1.5V Reserved Reserved GND Reserved Reserved Reserved Reserved Reserved Description No Connect 3.3V Power No Connect Return Current Path No Connect 1.5V Power ( No use ) No Connect No Connect Return Current Path No Connect No Connect No Connect No Connect No Connect Prodcut Specification Name P15 P16 P17 P18 P19 P20 P21 P22 P23 P24 P25 P26 P27 P28 P29 P30 P31 P32 P33 P34 P35 P36 P37 P38 P39 P40 P41 P42 P43 Type GND Reserved Reserved GND Reserved Reserved GND Reserved +B +3.3V -B GND GND +1.5V GND Two Wire Interface -A Two Wire Interface +A GND GND Reserved GND Reserved +3.3V GND +3.3V Reserved Device Type P44 Device Sleep Signal P45 Vendor P46 Reserved P47 Vendor P48 P49 P50 +1.5V DAS GND P51 Presence Detection P52 +3.3V Product Specification Description Return Current Path No Connect No Connect Return Current Path No Connect No Connect Return Current Path No Connect Host Receiver Differential Signal Pair B 3.3V Power Host Receiver Differential Signal Pair B Return Current Path Return Current Path 1.5V Power ( No use ) Return Current Path No Connect Host Transmitter Differential Signal Pair A No Connect Host Transmitter Differential Signal Pair A Return Current Path Return Current Path No Connect Return Current Path No Connect 3.3V Power Return Current Path 3.3V Power No Connect No Connect If system didn't support DEVSLP, set DEVSLP Sleep Signal pin power high and keep (from power on), device will ignore. If system support DEVSLP, set DEVSLP Sleep Signal pin power low (from power on) device, device will support DEVSLP function. Device Sleep Signal H: SSD enter sleep model. Device Sleep Signal L: SSD exit sleep model. Vendor Specific / Manufacturing Pin/No connect on the host side No Connect Vendor Specific / Manufacturing Pin/No connect on the host side 1.5V Power ( No use ) Device Activity Signal Return Current Path This pin connect 0 ohm resistor to GND to indicate the presence of an mSATA device 3.3V Power Page 13 of 23 3 ATA Command Sets 3.1 ATA Command The SSD supports all the mandatory ATA commands defined in the ATA/ATAPI-8 specification. 3.1.1 ATA General Feature Command Set The SSD supports the ATA General feature Command set (non-packet), which consists of ．EXECUTE DEVICE DIAGNOSTIC ．FLUSH CACHE ．IDENTIFY DEVICE ．READ DMA ．READ DMA WITHOUT RETRIES ．READ SECTOR(S) ．READ SECTORS(S) WITHOUT RETRIES ．READ VERIFY SECTORS(S) ．READ VERIFY SECTORS(S) WITHOUT RETRIES ．SEEK ．SET FEATURES ．WRITE DMA ．WRITE DMA WITHOUT RETRIES ．WRITE SECTOR(S) ．WRITE SECTOR(S) WITHOUT RETRY ．READ MULTIPLE ．SET MULTIPLE MODE ．WRITE MULTIPLE ．INITIALIZE DEVICE PARAMETERS ．DATA SET MANAGEMENT The SSD supports all the following optional commands ．READ BUFFER ．WRITE BUFFER ．DOWNLOAD MICROCODE Page 14 of 23 Prodcut Specification 3.1.2 Identify Device Data The following table details the sector data returned after issuing an IDENTIFY DEVICE command. Table 14 Returned Sector Data Word 0 1 2 3 4-5 6 7-8 9 10-19 20-22 23-26 27-46 F=Fixed V=Variable Default Value X=Both F 0040h F 3FFFh F C837h F 0010h F 0000h F 003Fh F 0000h F 0000h V Var. F 0000h V Var. V Var. 47 F 8010h 48 49 50 51-52 53 54 55 56 57-58 F F F F F V V V V 4000h 2F00h 4000h 0000h 0007h Var. Var. Var. Var. 59 V 0101h 60-61 V 62 63 64 65 66 67 68 69-70 71-74 75 76 F V F F F F F F F F V Product Specification 125,045,424 (64GB) 250,069,680 (128GB) 500,118,192 (256GB) 1,000,215,216 (512GB) 0000h 0007h 0003h 0078h 0078h 0078h 0078h 0000h 0000h 001Fh 070Eh Description General configuration bit-significant information Obsolete-Number of logical cylinders (16,383) Specific configuration Obsolete-Number of logical heads (16) Retired Obsolete-Number of logical sectors per logical track (63) Reserved for assignment by the Compact Flash Association Retired Serial number (20 ASCII characters) Retired / Obsolete Firmware revision (8 ASCII characters) Model number 7:0 – Maximum number of sectors transferred per interrupt on multiple commands Trusted Computing feature set options, bit14 should be 1 Capabilities Capabilities Obsolete Words 88 and 70:64 valid Obsolete - Number of logical cylinders (16,383) Obsolete - Number of logical heads (16) Obsolete - Number of logical sectors per logical track (63) Capacity(Cylinders*heads*sectors) Number of sectors transferred per interrupt on multiple commands Total number of user addressable logical sectors for 28-bit commands (DWord) Obsolete Multi-word DMA modes supported/selected PIO modes supported Minimum multiword DMA transfer cycle time per word Manufacture’s recommended multiword DMA transfer cycle time Minimum PIO transfer cycle time without flow control Minimum PIO transfer cycle time with IORDY flow control Reserved(for future command overlap and queuing) Reserved for the IDENTIFY packet DEVICE command 4:0 Maximum Queue depth-1=31 Serial ATA capabilities Page 15 of 23 Word 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 F=Fixed V=Variable Default Value X=Both V Var. V 004Ch V 0040h F 01FEh F 0021h F 346Bh F 7D01h F 4023h V 3469h V BC01h F 4023h V 407Fh F 0003h F 0003h F 0000h V Var. 93 V 94 95 96 97 98-99 F F F F F 100-103 V 104 F 105 F 106 107 F F 108-111 V 112-115 116 117-118 119 120 121-126 127 128 129-159 160 161-167 F F F F F F F V F F F Page 16 of 23 0000h Description Reserved for Serial ATA Serial ATA features supported Serial ATA features enabled Major Version Number Minor Version Number Commands and feature sets supported Commands and feature sets supported Commands and feature sets supported Commands and feature sets supported or enabled Commands and feature sets supported or enabled Commands and feature sets supported or enabled Ultra DMA modes Time required for security erase unit completion Time required for enhanced security erase completion Current advanced power management value Master Password Identifier Hardware reset result. The contents of bits (12:0) of this word shall change only during the execution of a hardware reset. Current AAM value Stream Minimum Request Size Streaming Transfer Time - DMA Streaming Access Latency - DMA and PIO Streaming Performance Granularity 0000h 0000h 0000h 0000h 0000h 125,045,424 (64GB) 250,069,680 (128GB) Maximum user LBA for 48-bit Address feature set 500,118,192 (256GB) 1,000,215,216 (512GB) 0000h Streaming Transfer Time - PIO Maximum number of 512-byte blocks per DATA SET 0008h MANAGEMENT command 6003h Physical sector size/logical sector size 0000h Inter-seek delay for ISO-7779 acoustic testing in microseconds 0000h 0000h World wide name 0000h 0000h 0000h Reserved for word wide name extension to 128 bits 0000h Reserved for TLC 0000h Words per logical sector 4010h Commands and feature sets supported 4010h Commands and feature sets supported or enabled 0000h Reserved for expanded supported and enabled settings 0000h Removable Media Status Notification feature set support 0021h Security status 0000h Vendor specific 0000h Compact Flash Association (CFA) power mode 1 0000h Reserved for the CompactFlash Association Prodcut Specification Word 168 169 170-173 174-175 176-205 206 207-208 209 210-211 212-213 214 215-216 217 218 219 220 221 222 223 224-229 230-233 F=Fixed V=Variable Default Value X=Both F 0000h F 0001h V Var. F 0000h F 0000h F 003Dh F 0000h F 4000h F 0000h F 0000h F 0000h F 0000h F 0001h F 0000h F 0000h F 0000h F 0000h F 1075F F 0000h F 0000h F 0000h 234 F 0000h 235 F 0000h Description DATA SET MANAGEMENT command is supported Additional Product Identifier (ATA String) Reserved Current media serial number (ATA string) SCT Command Transport Reserved Alignment of logical blocks within a physical block Write-Read-Verify Sector Count Mode 3 (DWord) Write-Read-Verify Sector Count Mode 2 (DWord) NV Cache Capabilities NV Cache Size in Logical Blocks (DWord) Nominal media rotation rate Reserved NV Cache Options 7:0 Write-Read-Verify feature set current mode Reserved Transport major version number Transport minor version number Reserved Extended Number of User Addressable Sectors (QWord) Minimum number of 512-byte data blocks per DOWNLOAD MICROCODE command for mode 03h Minimum number of 512-byte data blocks per DOWNLOAD MICROCODE command for mode 03h Reserved Integrity word 236-254 F 0000h 255 V Var. Note: 1. F=Fixed. The content of the word is fixed and does not change for removable media devices, these values may change when media is Removed or changed. 2. V=Variable. The state of at least one bit in a word is variable and may change depending on the state of the device or the commands executed by the device. 3. X=F or V. The content of the word may be fixed or variable. 3.2 Power Management Command Set The SSD supports the power management command set, which consists of ．CHECK POWER MODE ．IDLE ．IDLE IMMEDIATE ．SLEEP ．STANDBY ．STANDBY IMMEDIATE Product Specification Page 17 of 23 3.3 Security Mode Feature Set The SSD supports the Security Mode command set, which consist of ．SECURITY SET PASSWORD ．SECURITY UNLOCK ．SECURITY ERASE PREPARE ．SECURITY ERASE UNIT ．SECURITY FREEZE LOCK ．SECURITY DISABLE PASSWORD 3.4 SMART Command Set The SSD supports the SMART command set, which consist of ．SMART ENABLE OPERATIONS ．SMART DISABLE OPERATIONS ．SMART ENABLE/DISABLE AUTOSAVE ．SMART RETURN STATUS The SSD supports the following optional commands. ．SMART EXECUTE OFF-LINE IMMEDIATE ．SMART READ DATA ．SMART READ LOG ．SMART WRITE LOG The table below lists the SMART commands. Table 15 SMART commands Subcommand Code SMART ATTRIBUTE VALUES (READ DATA) READ ATTRIBUTE THRESHOLDS ENABLE/DISABLE ATTRIBUTE AUTOSAVE SAVE ATTRIBUTE VALUES EXECUTE OFF-LINE IMMEDIATE EXECUTE SMART OFF-LINE ROUTINE EXECUTE SMART SHORT SELF-TEST ROUTINE (OFFLINE) EXECUTE SMART EXTENDED SELF-TEST ROUTINE (OFFLINE) ABORT OFF-LINE ROUTINE EXECUTE SMART SHORT SELF-TEST ROUTINE (CAPTIVE) EXECUTE SMART EXTENDED SELF-TEST ROUTINE ( CAPTIVE ) READ LOG SECTOR WRITE LOG SECTOR ENABLE SMART OPERATIONS DISABLE SMART OPERATIONS RETURN SMART STATUS Enable/Disable Automatic OFFLINE D0h D1h D2h D3h D4h Page 18 of 23 LBA Low value 00h 01h 02h 7Fh 81h 82h D5h D6h D8h D9h DAh DBh Prodcut Specification 3.5 Host Protected Area Command Set The SSD supports the Host Protected Area command set which consists of ．READ NATIVE MAX ADDRESS ．SET MAX ADDRESS ．READ NATIVE MAX ADDRESS EXT ．SET MAX ADDRESS EXT The SSD supports the following optional commands. ．SET MAX SET PASSWORD ．SET MAX LOCK ．SET MAX FREEZE LOCK ．SET MAX UNLOCK 3.6 48-Bit Address Command Set The SSD supports the Host Protected Area command set, which consists of ．FLUSH CACHE EXT ．READ DMA EXT ．READ NATIVE MAX ADDRESS EXT ．READ SECTOR(S) EXT ．READ VERIFY SECTOR(S) EXT ．READ MULTIPLE EXT ．SET MAX ADDRESS EXT ．WRITE DMA EXT ．WRITE MULTIPLE EXT ．WRITE MULTIPLE FUA EXT ．WRITE SECTOR(S) EXT 3.7 Device Configuration Overlay Command Set The SSD supports the Device configuration Overlay command set, which consists of ．DEVICE CONFIGURATION FREEZE LOCK ．DEVICE CONFIGURATION IDENTITY ．DEVICE CONFIGURATION RESTORE ．DEVICE CONFIGURATION SET 3.8 General Purpose log Command Set The SSD supports the general purpose log command set, which consists of ．READ LOG EXT ．WRITE LOG EXT Product Specification Page 19 of 23 4 SATA Command Sets 4.1 SATA Command The SATA 3.0 Specification is a super set of the ATA/ATAPI-8 specification with regard to supported commands. The SSD supports the following features which are unique to the SATA 3.0 Specification. 4.1.1. Software Settings Preservation The SSD supports the SET FEATURES parameter to enable/disable the preservation of software settings. 4.1.2. Native Command Queuing The SSD supports the Native Command Queuing (NCQ) command set, which includes. ．READ FPDMA QUEUED ．WRITE FPDMA QUEUED Note: with a maximum queue depth equal to 32 Page 20 of 23 Prodcut Specification 5 References This document references standards defined by a variety of organizations as listed below. Table 16 Standards References Date Title Location Dec 2008 VCCI http://www.vcci.or.jp/vcci_e/general/jo in/index.html July 2007 ROHS Search for material description datasheet at http://intel.pcnalert.com July 2007 SFF-8144, 1.8” drive form factor http://www.sffcommittee.org February 2007 Serial ATA Revision 2.6 http://www.sata-io.org May 2006 SFF-8223, 2.5” Drive w/Serial Attachment Connector http://www.sffcommittee.org May 2005 SFF-8201, 2.5” drive form factor http://www.sffcommittee.org April 2004 ATA-7 Spec. Volume 1 http://www.t13.org/ Aug. 2009 ATA-8 Spec. Rev 2 http://www.t13.org/ International Electro Technical Commission EB61000 2008 4-2 Personnel Electrostatic Discharge Immunity 2008 4-3 Electromagnetic compatibility (EMC) 2004 4-4 Electromagnetic compatibility (EMC) 2005 4-5 Electromagnetic compatibility (EMC) 2008 4-6Electromagnetic compatibility (EMC) 2008 4-11 (Voltage variations) 2004 ENV 50204 (Radiated electromagnetic field from digital radio telephones) Product Specification http://www.iec.ch http://www.iec.ch Page 21 of 23 6 Terms and Acronyms This document incorporates many industry- and device-specific words use the following list to define a variety of terms and acronyms. Table 17 Glossary of Terms and Acronyms Term Definition ATA Advanced Technology Attachment ATAPI Advanced Technology Attachment Packet Interface BER Bit Error Rate, or percentage of bits that have errors relative to the total number of bits received BIOS Basic Input/Output System Chipset A term used to define a collection of integrated components required to make a PC function DIPM Device Initiated Power Management The ability of the device to request SATA link power state changes DMA Direct Memory Access DRAM Dynamic Random Access Memory EXT Extended FP First Party GB Giga-byte defined as 1X10 bytes HCI Host Controller Interface HCT Hardware Compatibility Test HDD Hard Disk Drive HIPM 9 Host Initiated Power Management The ability of the host to request SATA link power state changes Hot Plug A term used to describe the removal or insertion of a SATA hard drive when the system is powered on IOPS Input output operations per second LBA Logical Block Address LPM Link Power Management: the ability of the SATA link layer to enter one of two lower power consuming states, partial and slumber MB Mega-bytes defined as 1x10 bytes mSATA Mini-SATA MTBF Mean time between failure NCQ Native Command Queuing Page 22 of 23 6 Prodcut Specification The ability of the SATA hard drive to re-order commands in order to maximize the efficiency of gathering data from the platters NOP No operation NTFS NT file system OEM Original Equipment Manufacturer OS Operation System Port The point at which a SATA drive physically connected to the SATA controller RAID Redundant Array of Independent Disks RMS Root Mean Squared RPM Revolutions per Minute RTM Release to Manufacture SATA Serial ATA SFF Small Form Factor Self-Monitoring, Analysis and reporting Technology SMART An open standard for developing hard drive and software systems that automatically monitors a hard drive’s health and reports potential problems SSD Solid State Drive TBD To Be Determined WHQL Microsoft* Windows Hardware Quality Labs Write Cache A memory device within a hard drive, which is allocated for the temporary storage of data before that data is copied to its permanent storage location VCCI Voluntary Control Council for Interface Product Specification Page 23 of 23