96LEDK-A057VG70NX2

G057VN01 V2 ■ Preliminary Specification □ Final Specification Module 5.7 Inch Color TFT-LCD Model Name G057VN01 V2 Customer Date Approved by Date 2011/05/05 O nl y /2 01 Prepared by 1/ Checked & Approved by 7/ 6 Debbie Chiu 2011/05/05 General Display Business Division / AU Optronics corporation AU O C on f id e nt ia lF or PR O M AT E Note: This Specification is subject to change without notice. In te rn al U se Daniel PY Tsai G057VN01 V2 Ver. 0.1 1/22 G057VN01 V2 Contents 1. Operating Precautions .................................................................................... 4 2. General Description ........................................................................................ 5 2.1 Display Characteristics .......................................................................................................... 5 2.2 Optical Characteristics........................................................................................................... 6 3. Functional Block Diagram .............................................................................. 8 4. Absolute Maximum Ratings............................................................................ 9 4.1 Absolute Ratings.................................................................................................................... 9 4.2 Absolute Ratings of Environment .......................................................................................... 9 5. Electrical Characteristics.............................................................................. 10 5.1 TFT-LCD Driving .................................................................................................................. 10 5.2 Backlight Unit Driving........................................................................................................... 11 6. Signal Characteristic..................................................................................... 12 1/ 7/ 6 6.1 Pixel Format Image.............................................................................................................. 12 6.2 Scanning Direction............................................................................................................... 12 6.3 The Input Data Format......................................................................................................... 13 6.4 TFT- LCD Interface Signal Description................................................................................ 14 6.5 TFT- LCD Interface Timing................................................................................................... 15 6.6 LED Backlight Unit Interface Signal Description................................................................. 16 01 6.7 Power ON/OFF Sequence................................................................................................... 16 /2 7. Connector & Pin Assignment ....................................................................... 17 U se O nl y 7.1 TFT- LCD Signal (CN1): LCD Connector............................................................................ 17 7.2 LED Backlight Unit (CN2): Backlight Connector................................................................. 17 7.3 PIN 1 definition of CN1 and CN2 ........................................................................................ 18 E In te rn al 8. Reliability Test Criteria ................................................................................. 18 9. Mechanical Characteristics .......................................................................... 20 10. Label and Packaging................................................................................... 21 M AT 10.1 Shipping Label (on the rear side of TFT-LCD display) ..................................................... 21 10.2 Carton Package................................................................................................................. 21 PR O 11 Safety ............................................................................................................ 22 AU O C on f id e nt ia lF or 11.1 Keen Edge Requirements ................................................................................................. 22 11.2 Materials ............................................................................................................................. 22 11.3 Capacitors .......................................................................................................................... 22 11.4 National Test Lab Requirement ......................................................................................... 22 G057VN01 V2 Ver. 0.1 2/22 G057VN01 V2 Record of Revision Version and Date Page Old description All First edition preliminary specifications Remark AU O C on f id e nt ia lF or PR O M AT E In te rn al U se O nl y /2 01 1/ 7/ 6 0.1, May, 05, 2011 New Description G057VN01 V2 Ver. 0.1 3/22 G057VN01 V2 1. Operating Precautions AU O C on f id e nt ia lF or PR O M AT E In te rn al U se O nl y /2 01 1/ 7/ 6 1) Display area (Polarizer) of TFT-LCD Module is easily to be damaged, please be cautious and not to scratch it. 2) Be sure to power off your machine before connecting or disconnecting your signal cable to TFT-LCD Module. 3) Wipe off water drop on display area immediately. Long contact with water may cause discoloration or spots. 4) When the panel surface is soiled, wipe it with absorbent cotton or soft cloth. 5) Display area (Glass) of TFT-LCD Module may be broken or cracked if bump Module against hard object. 6) To avoid ESD (Electro Static Discharde) damage, be sure to ground yourself before handling TFT-LCD Module. 7) Do not open nor modify the TFT-LCD module assembly. 8) Do not press the reflector sheet at the back of the module to any direction. 9) In case if TFT-LCD module has to be put back into the packing container slot after it was taken out from the container, do not press the center of the LED Reflector edge. Instead, press at the far ends of the LED Reflector edge softly. Otherwise the TFT-LCD Module may be damaged. 10) When inserting or removing of your signal cable to TFT-LCD Module, be sure not to apply abnormal force (rotate, tilt…etc.) to the Connector of the TFT-LCD Module. 11) TFT-LCD Module is not allowed to be twisted & bent even force is added on module in a very short time. Please design your display product well to avoid external force applying to module by end-user directly. 12) Small amount of materials without flammability grade are used in the TFT-LCD module. The TFT-LCD module should be supplied by power complied with requirements of Limited Power Source (IEC60950 or UL1950), or be applied exemption. 13) Severe temperature condition may result in different luminance, response time. 14) Continuous operating TFT-LCD Module under high temperature environment may accelerate LED light bar exhaustion and reduce luminance dramatically. 15) The data on this specification sheet is applicable when TFT-LCD module is placed in landscape position. 16) Continuous displaying fixed pattern may induce image sticking. It’s recommended to use screen saver or moving content periodically if fixed pattern is displayed on the screen. G057VN01 V2 Ver. 0.1 4/22 G057VN01 V2 2. General Description G057VN01 V2 is designed for industrial display applications with VGA (640 x RGB x 480) resolution and 262k colors (RGB 6-bits). It is composed of a TFT-LCD panel, driver ICs, control and power supply circuits board and backlight unit including LED driver circuit. G057VN01 V2 offers CMOS interface for display signal input. 2.1 Display Characteristics The following items are G057VN01 V2 characteristics summary at 25 (Room Temperature). Items Unit Specifications Active Area mm 115.2(H) x 86.4(V) Screen Diagonal inch 5.7 Pixels H x V 640 x 3(RGB) x 480 Pixel Pitch mm 0.18 x 0.18 Pixel Arrangement R.G.B. Vertical Stripe Display Mode TN, Normally White Volt 3.3 typ. Typical Power Consumption Watt TBD Grams TBD 7/ 1/ 01 144.0(H)x 104.6(V) x 12.3(D) (typ.) y mm nl Physical Size /2 Weight 6 Nominal Input Voltage VDD CMOS 6-bit Parallel RGB Surface Treatment Anti-Glare, Hardness 3H U se O Electrical Interface In te rn al Support Color The most suitable view angle 12 o’clock PR O M AT E Temperature Range Operating Storage (Non-Operating) 262K colors o -30 to +85 -30 to +85 RoHS Compliance AU O C on f id e nt ia lF or RoHS Compliance C C o G057VN01 V2 Ver. 0.1 5/22 
vengdistac 1
with50cm G057VN01 V2 2.2 Optical Characteristics The optical characteristics are measured under stable conditions at 25 Uniformity % Contrast Ratio msec Response Time msec msec Viewing Angle Rising 1.3 500 800 15 - 20 Note 4 - 10 15 Note 5 - Falling Rising + Falling 25 35 70 80 - Horizontal CR = 10 (Right) (Left) 70 degree degree Vertical CR = 10 (Upper) (Lower) 60 80 70 60 White x 70 Red y Green x TBD TBD TBD TBD TBD TBD TBD TBD /2 TBD nl y TBD O se - TBD TBD 50 Note 1, 2, 3 Note 6 TBD TBD TBD TBD - rn al U % TBD TBD Note 1 - TBD TBD Green y - TBD TBD Remark - TBD TBD Red x - - degree degree Blue y Note 1: Measurement method Pattern Generator, Power Supply, Digital Voltmeter, Luminance meter (SR_3 or equivalent) M < 1 lux or Environment Center PR O Test Point AT E Aperture In te Equipment - 700 5 Points Blue x Color Gamut Max. 525 White y Color / Chromaticity Coordinates (CIE 1931) Typ. 6 cd/m2 Min. 7/ White Luminance Conditions VLED =12V, DPWM =100% (center point) 1/ Unit 01 Item (Room Temperature). ia lF LCD Module nt equivalent id e on f C O AU SR_3 or measuring distance Module Driving Equipment G057VN01 V2 Ver. 0.1 6/22 G057VN01 V2 Note 2: Definition of 5 points position (Display active area: 115.2mm(W) x 86.4mm(H)) W W /4 W /4 W /4 W /4 H /4 1 2 H /4 3 H H /4 4 5 H /4 Note 3: The luminance uniformity of 5 points is defined by dividing the maximum luminance value by the minimum luminance value at full white condition. 7/ 1/ Minimum Brightness of five points 6 Maximum Brightness of five points δW5 = /2 01 Note 4: Definition of contrast ratio (CR): y Brightness @ “White” state nl Contrast ratio (CR) = U se O Brightness @ “Black” state rn al Note 5: Definition of response time: In te The output signals of photo detector are measured when the input signals are changed from “White” to “Black” (falling time) E and from “Black” to “White” (rising time), respectively. The response time interval definition is between 10% and 90% of PR O M AT amplitude. Please refer to the figure as below. Tf Tr O C response on f id e Optical AU ia nt 100 90 lF or % White Black White 10 0 G057VN01 V2 Ver. 0.1 7/22 Viewngalsthm eurntofcasri# G057VN01 V2 Note 6: Definition of viewing angle 10, at the screen center, over 180° horizontal and 180° vertical range. The 180° horizontal (θL, θR) and 180° vertical (ΦH, ΦL) range are illustrated as following figure. 3. Functional Block Diagram AU O C on f id e nt ia lF or PR O M AT E In te rn al U se O nl y /2 01 1/ 7/ 6 The following diagram shows the functional block of the G057VN01 V2 color TFT/LCD module. G057VN01 V2 Ver. 0.1 8/22 Bulbshode39/anocdes3 G057VN01 V2 4. Absolute Maximum Ratings 4.1 Absolute Ratings Symbo Min Max Unit Remark Logic/LCD Drive Voltage VDD -0.3 +3.6 Volt Ta= 25 C LCD Input Signal Voltage VIN -0.3 +3.6 Volt Ta= 25oC LED BLU Drive Voltage VLED 0 23 Volt Ta= 25oC VPWM 0 8 Volt Ta= 25 C Symbol Min Max Unit Remark TOP -30 +85 ℃ Note 1, 2 TST -30 +85 Item LED Dimming Input Voltage High o o 4.2 Absolute Ratings of Environment HOP Storage Temperature Storage Humidity HST 95 5 %RH Note 1, 2 Note 1 ℃ 95 %RH Note 1 tion. 1/ Note 1: Maximum Wet- 5 6 Operation Humidity 7/ Operating Temperature 01 Item AU O C on f id e nt ia lF or PR O M AT E In te rn al U se O nl y /2 Note 2: Only operation is guaranteed. Optical performance should be evaluated at 25 only. G057VN01 V2 Ver. 0.1 9/22 G057VN01 V2 5. Electrical Characteristics 5.1 TFT-LCD Driving 5.1.1 Power Specification Symbol Parameter Min Typ Max Units 3.0 3.3 3.6 Volt VDD Logic/LCD Drive Voltage IDD VDD Current - 140 155 mA Irush LCD Inrush Current - - 1.5 A PDD VDD Power - TBD TBD Watt Allowable Logic/LCD Drive Ripple Voltage - - 100 mVp-p VDDrp Remark All Black Pattern (VDD=3.3V, at 60Hz) Note 1 All Black Pattern (VDD=3.3V, at 60Hz) All Black Pattern (VDD=3.3V, at 60Hz) Q3 AO6402 1 47K 7/ 1/ se 0.01uF/25V AT 1K U S VR1 R2 In te SW MAG-SPST E 2 SW1 rn al C3 +12.0V (LCD Module Input) Q3 AO6402 G 1K C1 1uF/16V VCC O D1 D2 D5 D6 R2 VDD nl y G R1 47K (High to Low) Control Signal F1 S 01 D6 D5 D2 D1 /2 +3.3V 6 Note 1: Measurement condition: or PR O M C2 1uF/25V 3.3V AU O C on f id e nt ia lF 90% 0V 10% 0.5ms VDD rising time G057VN01 V2 Ver. 0.1 10/22 4(Ro G057VN01 V2 5.1.2 Signal Electrical Characteristics Input signals shall be low or Hi-Z state when VDD is off. Parameter Logic Input Voltage for Display Signals Input Voltage for RL/UD Symbol Min. Typ. Max. Unit High VIH 0.7VDD - VDD Volt Low VIL 0 - 0.3VDD Volt High VIH 0.7VDD - VDD Volt Low VIL 0 - 0.3VDD Volt 5.2 Backlight Unit Driving 5.2.1 Parameter guideline for LED Following characteristics are measured under stable condition using a LED driving board at 25 Min Typ Max Units 20 Volt Input Voltage 9 12 ILED Input Current - TBD Inrush Current - TBD 2.0 FPWM Dimming Frequency 200 DPWM Dimming duty cycle 1 Off Control Voltage - 3.3 rn al 50000 Volt Volt 30K Hz 100 % 5.5 Volt - 0.8 Volt - - Hrs om Temperature) Remark VLED =12V, DPWM =100% VLED =12V, DPWM =100% VLED =12V, DPWM =100% Note 1,2 Note 3, 4 Note 5, 6 E Operating Life A 0.2 U 2 In te On Control Voltage VLED On/Off - O - 5.5 se Dimming control Voltage Low 3.3 W 01 Dimming control Voltage High VPWM DIM 1.5 /2 IrushLED - y Power Consumption nl PLED A 6 VLED 7/ Parameter 1/ Symbol Remarks PR O M (PWM High: ON and PWM Low: OFF) AT Note 1: PWM dimming function can be operated by PWM signal. PWM duty cycle can adjust white Luminance. Note 2: PWM signal can not be floating and pull-down to ground when waiting. On/Off) must be turned on late than VLED and PWM Signal. or Note 3: Enable (VLED ia lF Note 4: Enable (VLED On/Off) must be turned off early than VLED and PWM Signal. nt Note 5: If G057VN01 V2 module is driven by high current or at high ambient temperature & humidity condition. The id e operating life will be reduced. on f Note 6: Operating life means brightness goes down to 50% initial brightness. Minimum operating life time is estimated data. AU O C Note 7: See Section 6.6 for LED Backlight Unit Interface Signal Description G057VN01 V2 Ver. 0.1 11/22 G057VN01 V2 6. Signal Characteristic 6.1 Pixel Format Image 01 1/ 7/ 6 Following figure shows the relationship between input signal and LCD pixel format. /2 6.2 Scanning Direction AU O C on f id e nt ia lF or PR O M AT E In te rn al U se O nl y The following figures show the image seen from the front view. The arrow indicates the direction of scan. Note 1: TFT-LCD interface signal description is shown in section 6.4. G057VN01 V2 Ver. 0.1 12/22 G057VN01 V2 6.3 The Input Data Format This product displays 262,144 colors in terms of the 64 grey levels on RGB respectively. The following table demonstrates AU O C on f id e nt ia lF or PR O M AT E In te rn al U se O nl y /2 01 1/ 7/ 6 the display of input data. G057VN01 V2 Ver. 0.1 13/22 G057VN01 V2 AU O C on f id e nt ia lF or PR O M AT E In te rn al U se O nl y /2 01 1/ 7/ 6 6.4 TFT- LCD Interface Signal Description Note 1: “Low” stands for 0V. “High” stands for 3.3V. “NC” stands for ”No Connection”. G057VN01 V2 Ver. 0.1 14/22 G057VN01 V2 6.5 TFT- LCD Interface Timing 6.5.1 Timing Characteristics DE mode only Signal Symbol Min. Typ. Max. Unit Remark 1/ TCLOCK 23.9 25.2 34.2 MHz Note1 Period TH 770 800 1000 Active THD TCLOCK Note1 Blanking THB 130 160 360 Period TV 516 525 570 Active TVD TLINE Note1 Blanking TVB Clock frequency (DOTCLK) Horizontal Section Vertical Section Note 1: Recommended frame rate is 60 Hz. 640 480 36 45 90 6.5.2 Input Timing Diagram Input Timing Definition ( DE Mode) 7/ 6 TCLOCK /2 01 1/ DOTCLK Pixel 3 Pixel N-1 y Pixel 2 nl Pixel 1 O Invaild Data Pixel N Invaild Data Pixel 1 DE rn al U se Input Data THB In te THD M AT E TH PR O DE TVB TV AU O C on f id e nt ia lF or TVD G057VN01 V2 Ver. 0.1 15/22 G057VN01 V2 6.6 LED Backlight Unit Interface Signal Description Pin # Symbol Pin Description 2 VLED 12V input 1 VLED 3 GND 5 PWM DIM 4 12V input Ground GND 6 Ground 1~100% PWM dimming LED On/Off 0V-Off; 3.3~5V/NC-On Note 1: “NC” stands for ”No Connection” 6.7 Power ON/OFF Sequence VDD power, LCD interface signals and backlight on/off sequence are shown in the following chart. Signals from any system rn al U se O nl y /2 01 1/ 7/ 6 shall be Hi-Z state or low level when VDD is off. O C on f id e nt ia lF or PR O M AT E In te Power ON/OFF sequence timing AU ON/OFF sequence should be applied to avoid abnormal function in the display. Please make sure to turn off the power when you plug the cable into the input connector or pull the cable out of the connector. G057VN01 V2 Ver. 0.1 16/22 G057VN01 V2 7. Connector & Pin Assignment 7.1 TFT- LCD Signal (CN1): LCD Connector Manufacturer Starconn 089H33-000100-G2-R, compatible with Connector Model Number IMSA-9637S-33Y902 & ELCO 08-6210--033-340-800+ Pin# Symbol Pin# Symbol Pin# Symbol 1 GND 12 GND 23 B3 NC 14 G1 25 B5 5 GND 16 G3 27 7 R1 6 15 R0 8 9 G2 17 G4 18 R2 R3 24 G5 26 GND 28 VDD R/L GND 30 32 B0 R4 21 B1 11 R5 22 B2 31 VDD U/D NC 33 GND /2 10 DE 29 19 20 B4 6 NC G0 7/ 4 3 13 1/ DOTCLK 01 2 nl O se JST rn al U Manufacturer y 7.2 LED Backlight Unit (CN2): Backlight Connector SM06B-SRKS-G-TB In te Connector Model Number E compatible with JST SM06B-SRSS-TB (LS) (SN) JST SHR-06V-BKHF-B or compatible Symbol Pin # Symbol 1 VLED 4 GND VLED 5 PWM DIM GND 6 LED ON/OFF lF Pin # or PR O M AT Mating Connecter Model Number ia 2 AU O C on f id e nt 3 G057VN01 V2 Ver. 0.1 17/22 ,h3ousHr 40:/9% G057VN01 V2 7.3 PIN 1 definition of CN1 and CN2 1/ 7/ 6 (Rear side of TFT-LCD) nl y /2 01 8. Reliability Test Criteria Required Condition -30℃,300 hours AT PR O M Note 2 85℃/1 Hr (min.), power on/off per 5 minutes, repeat 5 times Hot Start Test -30℃/1 Hr (min.), power on/off per 5 minutes, repeat 5 times or Cold Start Test lF Shock Test (Non-Operating) Note 2 Note 2 50G,20ms,Half-sine wave, (±X, ±Y, ±Z) Note 2 1.5G, 10~200~10Hz, Sine wave, 30mins/axis, 3 direction (X, Y, Z) Note 2 ia nt id e on f C O Note 2 -20℃/30 min ,60℃/30 min ,100cycles Thermal Shock Test AU Note 2 E 85 Low Temperature Storage Note 2 In te -3 High Temperature Storage Note 2 rn al 85 Low Temperature Operation Attitude Test U High Temperature Operation ESD Note 2 se Temperature Humidity Bias Vibration Test (Non-Operating) Remark O Items Contact Discharge: ±8KV, 150pF(330Ω) 1sec, 8 points, 25 times/point Air Discharge: ±15KV, 150pF(330Ω) 1sec, 8 points, 25 times/point Operating: 14,000 ft, Ramp: 2000 ft/min, 8hrs Non-operating: 40,000 ft, Ramp: 2000 ft/min, 24hrs Note 1,2 Note 2 G057VN01 V2 Ver. 0.1 18/22 G057VN01 V2 Note1: According to EN61000-4-2 ESD class B criteria, some performance degradation is allowed. TFT-LCD module Note2: To inspect TFT-LCD module after reliability test, please store it at room temperature and room humidity for 24 id e nt ia lF or PR O M AT E In te rn al U se O nl y /2 01 1/ 7/ 6 hours at least in advance. on f
The reliability test is performed only to examine the TFT-LCD module capability. C
Each test is done by new TFT-LCD module. Don’t use the same TFT-LCD module repeatedly for reliability test. O
Water condensation is not allowed for each test items. AU
is self-recoverable, no data lost and no hardware failures after test. G057VN01 V2 Ver. 0.1 19/22 O U on f C or lF ia nt id e M PR O 9. Mechanical Characteristics A E AT rn al In te se U y nl O 6 7/ 1/ 01 /2 20/22 G057VN01 V2 Ver. 0.1 G057VN01 V2 G057VN01 V2 10. Label and Packaging 10.1 Shipping Label (on the rear side of TFT-LCD display) 10.2 Carton Package Max. capacity: 60 pieces TFT-LCD module per carton Max. weight: 12.95 kg per carton AU O C on f id e nt ia lF or PR O M AT E In te rn al U se O nl y /2 01 1/ 7/ 6 Outside dimension of carton: 520(L)mm* 340(W)mm* 250(H)mm G057VN01 V2 Ver. 0.1 21/22 G057VN01 V2 11 Safety 11.1 Keen Edge Requirements There will be no keen edges or corners on the display assembly that could cause injury. 11.2 Materials 11.2.1 Toxicity There will be no carcinogenic materials used anywhere in the TFT-LCD module. If toxic materials are used, they will be reviewed and approved by the responsible AUO toxicologist. 11.2.2 Flammability All components including electrical components that do not meet the flammability grade UL94-V1 in the TFT-LCD Module will complete the flammability rating exception approval process. The printed circuit board will be made from material rated 94-V1 or better. The actual UL flammability rating will be printed on the printed circuit board. 7/ 6 11.3 Capacitors 01 1/ If any polarized capacitors are used in the TFT-LCD module, provisions will be made to keep them from being inserted nl y /2 backwards. se O 11.4 National Test Lab Requirement U The TFT-LCD Module will satisfy all requirements for compliance to UL 60950 (U.S.A. Information Technology AU O C on f id e nt ia lF or PR O M AT E In te rn al Equipment). G057VN01 V2 Ver. 0.1 22/22