AQD-D4U16E21-SE

288Pin DDR4 2133 ECC UDIMM 16GB Based on 1Gx8 AQD-D4U16E21-SE Advantech AQD-D4U16E21-SE Datasheet Rev. 1.0 2015-09-11 1 288Pin DDR4 2133 ECC UDIMM 16GB Based on 1Gx8 AQD-D4U16E21-SE Description Pin Identification DDR4 ECC U-DIMMs are high-speed and low power Symbol A0–A16 BA0, BA1 BG0, BG1 RAS_n CAS_n WE_n CS0_n, CS1_n CKE0, CKE1 memory modules that use 1Gx8bits DDR4 SDRAM in FBGA package and a 4K-bit serial EEPROM on a 288-pin printed circuit board. DDR4 ECC U-DIMMs are dual In-Line memory modules and are intended for mounting into 288-pin edge connector sockets. The synchronous design allows precise cycle control with the use of system clock. Data I/O transactions are ODT0, ODT1 possible on both edges of DQS. The large range of ACT_n DQ0–DQ63 CB0–CB7 operation frequencies and programmable latencies allow the same device to be useful for a variety of high bandwidth and high performance memory system DM_n/DBI_n/ applications. DQS0_t–DQS8_t Features  RoHS compliant  JEDEC standard 1.2V ± 0.06V power supply  VDDQ=1.2V ± 0.06V  Clock Freq: 1067MHZ for 2133Mb/s/Pin.  Programmable CAS Latency: 10,11,12,13,14,15,16  Programmable Additive Latency (Posted /CAS): DQS0_c–DQS8_c CK0_t, CK1_t CK0_c, CK1_c PARITY VDD 0,CL-2 or CL-1 clock  VREFCA Programmable /CAS Write Latency (CWL) VSS = 11, 14(DDR4-2133) VDDSPD  8 bit pre-fetch  Burst Length: 8, 4 with tCCD = 4 which does not allow SCL seamless read or write SDA  Bi-directional Differential Data-Strobe  On Die Termination with ODT pin SA0–SA2  Serial presence detect with EEPROM  On DIMM Thermal Sensor  Asynchronous reset ALERT_n VPP RESET_n EVENT_n VTT RFU NC 2 Function SDRAM address bus SDRAM bank select SDRAM bank group select SDRAM row address strobe SDRAM column address strobe SDRAM write enable DIMM Rank Select Lines SDRAM clock enable lines SDRAM on-die termination control lines SDRAM activate DIMM memory data bus DIMM ECC check bits Input data mask and data bus inversion SDRAM data strobes (positive line of differential pair) SDRAM data strobes (negative line of differential pair) SDRAM clocks (positive line of differential pair) SDRAM clocks (negative line of differential pair) SDRAM parity input SDRAM I/O and core power supply SDRAM command/address reference supply Power supply return (ground) Serial SPD EEPROM positive power supply 2 I C serial bus clock for EEPROM 2 I C serial bus data line for EEPROM 2 I C slave address select for EEPROM SDRAM ALERT_n SDRAM Supply Set DRAMs to a Known State SPD signals a thermal event has occurred SDRAM I/O termination supply Reserved for future use No Connection 288Pin DDR4 2133 ECC UDIMM 16GB Based on 1Gx8 AQD-D4U16E21-SE Dimensions (Unit: millimeter) Note: 1. Tolerances on all dimensions +/-0.15mm unless otherwise specified. 3 288Pin DDR4 2133 ECC UDIMM 16GB Based on 1Gx8 AQD-D4U16E21-SE Pin Assignments Pin No Pin Name Pin No Pin Name Pin No Pin Name Pin No Pin Name Pin No Pin Name Pin No Pin Name Pin No Pin Name Pin No Pin Name 01 NC 37 VSS 73 VDD 109 145 NC 181 DQ29 217 VDD 253 DQ41 02 VSS 38 DQ24 74 CK0_t 110 146 VREFCA 182 VSS 218 CK1_t 254 VSS 03 DQ4 39 75 CK0_c 111 147 VSS 183 DQ25 219 CK1_c 255 DQS5_c 04 VSS 40 76 VDD 112 VSS 148 DQ5 184 VSS 220 VDD 256 DQS5_t 05 06 41 42 77 78 VTT EVENT_n 113 114 DQ46 VSS 149 150 VSS DQ1 185 186 DQS3_c DQS3_t 221 222 VTT PARITY 257 258 VSS DQ47 43 DQ30 79 A0 115 DQ42 151 VSS 187 VSS 223 VDD 259 VSS 08 09 10 11 12 DQ0 VSS DM0_n/ DBI0_n, NC NC VSS DQ6 VSS DQ2 VSS DM3_n/ DBI3_n, NC NC VSS VSS DM5_n/ DBI5_n, NC NC 44 45 46 47 48 VSS DQ26 VSS CB4/ NC VSS 80 81 82 83 84 VDD BA0 RAS_n/A16 VDD CS0_n 116 117 118 119 120 152 153 154 155 156 DQS0_c DQS0_t VSS DQ7 VSS 188 189 190 191 192 DQ31 VSS DQ27 VSS CB5, NC 224 225 226 227 228 BA1 A10/AP VDD RFU WE_n/A14 260 261 262 263 264 DQ43 VSS DQ53 VSS DQ49 13 VSS 49 CB0/ NC 85 VDD 121 157 DQ3 193 VSS 229 VDD 265 VSS 14 DQ12 50 86 158 VSS 194 CB1, NC 230 NC 266 DQS6_c 15 VSS 51 16 17 52 53 19 20 21 22 23 DQ8 VSS DMI_n/ DBI1_n, NC NC VSS DQ14 VSS DQ10 55 56 57 58 59 VSS DM8_n/ DBI8_n, NC NC VSS CB6/ DBI8_n, NC VSS CB2/ NC VSS RESET_n VDD VSS DQ52 VSS DQ48 VSS DM6_n/ DBI6_n, NC NC 24 VSS 60 25 26 DQ20 VSS 27 28 07 18 29 CAS_n/A15 122 87 ODT0 123 VSS 159 DQ13 195 VSS 231 VDD 267 DQS6_t 88 89 VDD CS1_n 124 125 DQ54 VSS 160 161 VSS DQ9 196 197 DQS8_c DQS8_t 232 233 A13 VDD 268 269 VSS DQS5 90 VDD 126 DQ50 162 VSS 198 VSS 234 NC 270 VSS 91 92 93 94 95 ODT1 VDD NC VSS DQ36 127 128 129 130 131 163 164 165 166 167 DQS1_c DQS1_t VSS DQ15 VSS 199 200 201 202 203 CB7, NC VSS CB3, NC VSS CKE1 235 236 237 238 239 NC VDD NC SA2 VSS 271 272 273 274 275 DQ51 VSS DQ61 VSS DQ57 CKE0 96 VSS 132 168 DQ11 204 VDD 240 DQ37 276 VSS 61 62 VDD ACT_n 97 98 133 134 169 170 VSS DQ21 205 206 RFU VDD 241 242 VSS DQ33 277 278 DQS7_c DQS7_t DQ16 63 BG0 99 135 DQ62 171 VSS 207 BG1 243 VSS 279 VSS VSS DM2_n/ DBI2_n, NC NC VSS DQ22 VSS DQ18 VSS DQ28 64 VDD 100 DQ32 VSS DM4_n/ DBI4_n, NC NC VSS DQ60 VSS DQ56 VSS DM7_n/ DBI7_n, NC NC VSS 136 VSS 172 DQ17 208 ALERT_n 244 DQS4_c 280 DQ63 65 A12/BC_n 101 VSS 137 DQ58 173 VSS 209 VDD 245 DQS4_t 281 VSS 282 283 284 285 286 287 288 DQ59 VSS VDDSPD SDA VPP VPP VPP 54 30 66 A9 102 DQ38 138 VSS 174 DQS2_c 210 A11 246 VSS 31 67 VDD 103 VSS 139 SA0 175 DQS2_t 211 A7 247 DQ39 32 68 A8 104 DQ34 140 SA1 176 VSS 212 VDD 248 VSS 33 69 A6 105 VSS 141 SCL 177 DQ23 213 A5 249 DQ35 34 70 VDD 106 DQ44 142 VPP 178 VSS 214 A4 250 VSS 35 71 A3 107 VSS 143 VPP 179 DQ19 215 VDD 251 DQ45 36 72 A1 108 DQ40 144 RFU 180 VSS 216 A2 252 VSS Note: 1. VPP is 2.5V DC. 2. Pin 230 is defined as NC for UDIMMs, RDIMMs and LRDIMMs. Pin 230 is defined as SAVE_n for NVDIMMs. 3. Pins 1 and 145 are defined as NC for UDIMMs, RDIMMs and LRDIMMs. Pins 1 and 145 are defined as 12V for Hybrid /NVDIMM 4. The 5th VPP is required on all modules and DIMMs. 4 288Pin DDR4 2133 ECC UDIMM 16GB Based on 1Gx8 AQD-D4U16E21-SE Block Diagram 16GB, 2Gx72 Module(2 Rank x8) This technical information is based on industry standard data and tests believed to be reliable. However, Transcend makes no warranties, either expressed or implied, as to its accuracy and assume no liability in connection with the use of this product. Transcend reserves the right to make changes in specifications at any time without prior notice. 5 288Pin DDR4 2133 ECC UDIMM 16GB Based on 1Gx8 AQD-D4U16E21-SE Operating Temperature Condition Parameter Symbol Rating Unit Note Operating Temperature TOPER 0 to 85 C 1,2 Note: Operating Temperature is the ambient temperature. At 0 - 85C, operation temperature range is the temperature which all DRAM specification will be supported. Absolute Maximum DC Ratings Parameter Symbol Value Unit Note Voltage on VDD relative to Vss VDD -0.3 ~ 1.5 V 1 Voltage on VDDQ pin relative to Vss VDDQ -0.3 ~ 1.5 V 1 Voltage on VPP pin relative to Vss VPP -0.3 ~ 3.0 V 3 Voltage on any pin relative to Vss VIN, VOUT -0.3 ~ 1.5 V 1 Storage temperature TSTG -55~+100 C 1,2 Note: Stress greater than those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. Storage Temperature is the ambient temperature. VPP must be equal or greater than VDD/VDDQ at all times. AC & DC Operating Conditions Recommended DC operating conditions (SSTL –1.5) Rating Parameter Symbol Min Typ. Unit Note s V V V 1, 2 1, 2 3 Max Supply voltage VDD 1.14 1.2 1.26 Supply voltage for Output VDDQ 1.14 1.2 1.26 Wordline supply voltage VPP 2.375 2.5 2.75 Note: Under all conditions VDDQ must be less than or equal to VDD. VDDQ tracks with VDD, AC parameters are measured with VDD and VDDQ tied together. DC bandwidth is limited to 20MHz Single-ended AC & DC input levels for Command and Address DDR4-1600/1866/2133 Parameter Symbol Unit Note Min Max I/O Reference Voltage (CMD/ADD) VREFCA(DC) 0.49*VDD 0.51*VDD V 1,2 DC Input Logic High VIH.CA(DC) VREFCA+0.075 VDD V DC Input Logic Low VIL.CA(DC) VSS VREFCA-0.075 V AC Input Logic High VIH.CA(AC) VREF+0.1 Note 1 V AC Input Logic Low VIL.CA(AC) Note 1 VREF-0.1 V Note: The AC peak noise on VREFCA may not allow VREFCA to deviate from VREFCA(DC) by more than ± 1% VDD (for reference: approx. ± 12mV) For reference: approx. VDD/2 ± 12mV 6 288Pin DDR4 2133 ECC UDIMM 16GB Based on 1Gx8 AQD-D4U16E21-SE Differential AC and DC Input Levels DDR4-1600/1866/2133 Parameter Symbol Unit Note Min Max differential input high DC VIHdiff(DC) +0.150 NOTE 3 V 1 differential input low DC VILdiff(DC) NOTE 3 -0.150 V 1 differential input high AC VIHdiff(AC) 2 x (VIH(AC) - VREF) NOTE 3 V 2 differential input low AC VILdiff(AC) NOTE 3 2 x (VIL(AC) -VREF) V 2 Note: Used to define a differential signal slew-rate. For CK_t - CK_c use VIH.CA/VIL.CA(AC) of ADD/CMD and VREFCA; These values are not defined; however, the differential signals CK_t - CK_c, need to be within the respective limits (VIH.CA(DC) max, VIL.CA(DC)min) for single-ended signals as well as the limitations for overshoot and undershoot. Single-ended AC & DC output levels Parameter Symbol DDR4-1600/1866/2133 Unit Note DC output high measurement level VOH(DC) 1.1 x VDDQ V DC output mid measurement level VOM(DC) 0.8 x VDDQ V DC output low measurement level VOL(DC) 0.5 x VDDQ V AC output high measurement level VOH(AC) (0.7 + 0.15) x VDDQ V 1 AC output low measurement level VOL(AC) (0.7 - 0.15) x VDDQ V 1 Note: The swing of ± 0.15 × VDDQ is based on approximately 50% of the static single-ended output peak-to-peak swing with a driver impedance of RZQ/7Ω and an effective test load of 50Ω to VTT = VDDQ. Differential AC & DC output levels Parameter Symbol DDR4-1600/1866/2133 Unit Note AC differential output high VOHdiff(AC) +0.3 x VDDQ V 1 measurement level AC differential output low VOLdiff(AC) -0.3 x VDDQ V 1 measurement level Note: The swing of ± 0.3 × VDDQ is based on approximately 50% of the static differential output peak-to-peak swing with a driver impedance of RZQ/7Ω and an effective test load of 50Ω to VTT = VDDQ at each of the differential outputs. Temperature Sensor With SPD EEPROM Operating Conditions Parameter/Condition Symbol Supply voltage Input low voltage: logic 0; all inputs Input high voltage: logic 1; all inputs Output low voltage: 3mA sink current VDDSPD > 2V Input leakage current: (SCL, SDA) VIN = VDDSPD or VSSSPD Output leakage current: VOUT = VDDSPD or VSSSPD, SDA in High-Z 7 VDDSPD VIL VIH VOL ILI ILO Min Nom Max Units VDDSPD x 0.3 VDDSPD + 0.5 0.4 +/- 5 +/- 5 V V V V uA uA 2.5 -0.5 VDDSPD x 0.7 288Pin DDR4 2133 ECC UDIMM 16GB Based on 1Gx8 AQD-D4U16E21-SE IDD Specification parameters Definition (IDD values are for full operating range of Voltage and Temperature) 16GB, 2Gx72 Module (2 Rank x8) Parameter Symbol DDR4 2133 CL15 IDD Max. IPP Max. Unit Operating One bank Active-Precharge current; tCK = tCK(IDD), tRC = IDD0 / IPP0 513 63 mA IDD1 / IPP1 648 63 mA IDD2P / IPP2P 288 54 mA IDD2Q / IPP2Q 378 54 mA /CS is HIGH; Other control and address bus inputs are SWITCHING; Data bus inputs are SWITCHING IDD2N / IPP2N 396 54 mA Active power - down current; All banks open; tCK = tCK(IDD); CKE is IDD3P / IPP3P 378 54 mA IDD3N / IPP3N 522 54 mA IDD4R / IPP4R 1125 54 mA IDD4W / IPP4W 954 54 mA IDD5B / IPP5B 2169 189 mA IDD6N / IPP6N 414 72 mA IDD7 / IPP7 1728 99 mA tRC(IDD), tRAS = tRASmin(IDD); CKE is HIGH, /CS is HIGH between valid commands;Address bus inputs are SWITCHING; Data bus inputs are SWITCHING Operating One bank Active-read-Precharge current; IOUT = 0mA; BL = 8, CL = CL(IDD), AL = 0; tCK = tCK(IDD), tRC = tRC (IDD), tRAS = tRASmin(IDD), tRCD = tRCD(IDD); CKE is HIGH, /CS is HIGH between valid commands; Address bus inputs are SWITCHING; Data pattern is same as IDD4W Precharge power-down current; All banks idle; tCK = tCK(IDD); CKE is LOW; Other control and address bus inputs are STABLE; Data bus inputs are FLOATING Precharge quiet standby current; All banks idle; tCK = tCK(IDD); CKE is HIGH, /CS is HIGH; Other control and address bus inputs are STABLE; Data bus inputs are FLOATING Precharge standby current; All banks idle; tCK = tCK(IDD); CKE is HIGH, LOW; Other control and address bus inputs are STABLE; Data bus inputs are FLOATING Active standby current; All banks open; tCK = tCK(IDD), tRAS = tRASmax(IDD), tRP = tRP(IDD); CKE is HIGH, /CS is HIGH between valid commands; Other control and address bus inputs are SWITCHING; Data bus inputs are SWITCHING Operating burst read current; All banks open, Continuous burst reads, IOUT = 0mA; BL = 4, CL = CL(IDD), AL = 0; tCK = tCK(IDD), tRAS = tRASmax(IDD), tRP = tRP(IDD); CKE is HIGH, /CS is HIGH between valid commands; Address bus inputs are SWITCHING; Data pattern is same as IDD4W Operating burst write current; All banks open, Continuous burst writes; BL = 8, CL = CL(IDD), AL = 0; tCK = tCK(IDD), tRAS = tRASmax(IDD), tRP = tRP(IDD); CKE is HIGH, /CS is HIGH between valid commands; Address bus inputs are SWITCHING; Data bus inputs are SWITCHING IDD4R Burst refresh current; tCK = tCK(IDD); Refresh command at every tRFC(IDD) interval; CKE is HIGH, /CS is HIGH between valid commands; Other control and address bus inputs are SWITCHING; Data bus inputs are SWITCHING Self refresh current; CK and /CK at 0V; CKE ≒ 0.2V; Other control and address bus inputs are FLOATING; Data bus inputs are FLOATING Operating bank interleave read current; All bank interleaving reads, IOUT = 0mA; BL = 8, CL = CL(IDD), AL = tRCD(IDD)-1*tCK(IDD); tCK = tCK(IDD), Trc = tRC(IDD), tRRD = tRRD(IDD), tRCD = 1*tCK(IDD); CKE is HIGH, CS is HIGH between valid commands;Address bus inputs are STABLE during DESELECTs; Data pattern is same as IDD4R; Note: Module IDD was calculated on the specific brand DRAM(2Xnm) component IDD and can be differently measured according to DQ loading capacitor. 8 288Pin DDR4 2133 ECC UDIMM 16GB Based on 1Gx8 AQD-D4U16E21-SE Timing Parameters & Specifications Speed Parameter Symbol Average Clock Period tCK CK high-level width tCH CK low-level width tCL DQS_t,DQS_c to DQ skew, per group, per tDQSQ(total) access DQS_t,DQS_c to DQ Skew deterministic, per tDQSQ(dj) group, per access DDR4 2133 Unit Min 0.938 0.48 0.48 Max