BB-FOSTCDR

Standard Serial to Fiber Optic Converters Models FOSTCDR, FOSTCDR-INV www.advantech-bb.com PRODUCT FEATURES • Data rates up to 115.2 kbps • 4 km (2.5 mi) range • 10 to 30 VDC input voltage • Wide operating temperature • 2000V, 2-way isolation • Modbus ASCII/RTU compatible • EMI/RFI protection • TD, RD and Power LED's The FOSTCDRx line of fiber optic converters are suitable for standard industrial installations. These converters extend data communications up to 4 km (2.5 mi) and provide two-way optical isolation on the input and output lines. ORDERING INFORMATION MODEL NUMBER FOSTCDR SERIAL CONNECTOR Terminal Block FIBER CONNECTOR Multi-mode ST ISOLATION 2,000 V INVERTED FIBER STATE* - Model FOSTCDR industrial serial to multimode fiber optic converter, provides the most versatile connection possible between any asynchronous full or half-duplex serial equipment. In addition to direct point-to-point connectivity, it is capable operating in a multi-drop mode. This allows one serial device to communicate with up to 31 other devices around a fiber optic ring. Since the FOSTCDR supports mixed serial standards, you can replace other converters and isolators and add the EMI/RFI immunity inherent to fiber optic communications. FOSTCDR-INV Terminal Block Multi-mode ST 2,000 V  * Fiber is Off in the idle state. ACCESSORIES MDR-40-24 - DIN Rail Mount Power Supply 24VDC, 1.7 A output power DFMM-STST-1M - Multimode fiber patch cable ST-ST connectors An Automatic Send Data Control circuit controls the RS-422/485 driver chip, eliminating the requirement for special software. Easy to install and configure, it has an 8-position DIP switch to set up the RS-422/485 parameters and terminal blocks to connect serial signals and power. In RS-232 mode, it supports Transmit and Receive data. Handshaking signals are not passed through. Model FOSTCDR-INV features an “inverted fiber state” and is suitable for applications requiring the fiber optic light to be Off in the idle state. What is the difference between Model FOSTCDR and Model FOSTCDR-INV? The FOSTCDR keeps the light in the fiber turned On when no data is transmitted and the input signal is in the MARK state (idle). If light is lost or too low, the electrical signals go to the SPACE state. The input signal turns the light Off/On in step with the data. This model has an indicator for Transmit and Receive, if no light is received, the RD LED will come on, the RD output will be positive relative to GND (normally negative), and in RS-422 or RS-485 mode, no light will set the TD(A)- line high relative to TD(B)+. The usual voltage with light in the fiber and no signal sets the B line high relative to A (about 4.4 Volts DC no termination). The FOSTCDR-INV is the opposite. The fiber is Off in the idle state. All product specifications are subject to change without notice. FOSTCDR, FOSTCDR-INV_3017ds orders@advantech-bb.com support@advantech-bb.com Corporate Headquarters: 707 Dayton Road, PO Box 1040 Ottawa, IL 61350 USA 815-433-5100 Fax 433-5104 European Office: Westlink Commercial Park, Oranmore Co. Galway Ireland +353 91 792444 Fax +353 91 792445 Standard Serial to Fiber Optic Converters Models FOSTCDR, FOSTCDR-INV SPECIFICATIONS SERIAL TECHNOLOGY Data Rate RS-232 RS-422/485 RS-232: 115.2 Kbps maximum RS-422/485: 460.8 Kbps maximum Connector Terminal block (24 to 14 AWG) RS-232 TD, RD, GND Connector Terminal block (24 to 14 AWG) RS-485, 2-wire Data A(-), Data B(+), GND RS-422/485, 4-wire TDA(-), TDB(+), RDA(-), RDB(+), GND ISOLATION Rating 2KV RMS, 1 minute Lines Protected 2-way (input, output lines) Method Optical FIBER OPTIC TECHNOLOGY Type / Wavelength Multi-mode / 820 nm Output Power (-) 17 to (-) 10 dBm Receive Sensitivity (-) 25.4 dBm to (-) 24 dBm Cable 62.5/125 micro-meter Connector ST Data Rate 9.6 to 115.2 kbps Maximum Distance 4 km (2.5 mi) Idle State Transmitter light ON POWER Source External Input Voltage 10 to 30 VDC Consumption 1.7 Watts Connector Terminal block (24 to 14 AWG) INDUSTRIAL BUS Modbus ASCII/RTU MECHANICAL LED Indicators Serial TD, RD, Power Dimensions 10.6 x 7.9 x 2.5 cm (4.3 x 2.3 x 0.95 in) Enclosure 35mm DIN mount, plastic Weight 182 g (0.4 lbs) ENVIRONMENTAL Operating Temperature -40 to +80 °C (-40 to +176 °F) Storage Temperature -40 to +85 °C (-40 to +185 °F) Operating Humidity 0 to 95% non-condensing APPROVALS / CERTIFICATIONS - FOSTCDR cULus Recognized, File Number: E222870 FCC Part 15, CISPR, EN 55022 + AC:2011 Class A Emissions CE EN 61000-6-1 Generic Standards for Residential, Commercial and Light-Industrial Environments EN 61000-4-2 Electro-Static Discharge (ESD) EN 61000-4-3 +A1 +A2 +IS1 Radiated Field Immunity (RFI) EN 61000-4-4 Electrical Fast Transients-Burst Immunity (EFT) EN 61000-4-6 Conducted Immunity APPROVALS / CERTIFICATIONS - FOSTCDR-INV UL 508, File Number: E222870 FCC Part 15, CISPR, EN 55022 + AC:2011 Class A Emissions CE MTBF FOSTCDR 2187303 hours FOSTCDR-INV 2187303 hours Calculation Method MIL 217F Parts Count Reliability Prediction MECHANICAL DIAGRAM - Model FOSTCDR orders@advantech-bb.com support@advantech-bb.com Corporate Headquarters: 707 Dayton Road, PO Box 1040 Ottawa, IL 61350 USA 815-433-5100 Fax 433-5104 European Office: Westlink Commercial Park, Oranmore Co. Galway Ireland +353 91 792444 Fax +353 91 792445