BB-LDVDSV2-1587

LDVDSV2-1587_2313DS Page 1 Model LDVDSV2-1587 Advanced OBDII Data Streamer ™ The B&B Electronics AutoTap OBDII Data Streamer Model LDVDSV2 connects your PC, driver terminal, Java-enabled phone, or other on-board computing device to the OBDII diagnostic bus of light and medium duty vehicles. It enables the retrieval of the most commonly used parameters of value in telematics and fleet management applications. The LDVDSV2 provides a simple operational protocol to communicate to the OBDII bus. It provides a common interface and deterministic response time for all vehicles. The complete Command and Response protocol is published on B&B’s website www.rvdstreamer.com. OBDII Y-Cable J1708 Light or Medium Duty Car or Truck On-Board Computer w/GPS & Wireless Supported Vehicles The OBDII Streamer supports any 1996 or newer vehicles that comply with the SAE’s J1979 OBDII specification. Supported Protocols  SAE J1850 VPW  SAE J1850 PWM  SAE J2284/ ISO 15765 (CAN)  ISO 9141-2  ISO 14230-4 (KWP2000) Supported Parameters  Vehicle Identification Number  Vehicle Speed - Monitor aggressive driving  Engine Speed - Monitor idle time and engine abuse  Throttle Position  Odometer/Distance Traveled - Monitor trip distance and HOS  Instantaneous Fuel Rate in Gallons per Hour  Total Fuel - Monitor MPG & Protect against theft  Ignition status – Track Idle time  Battery Voltage – Watch for charging system failures  PTO Status - Automatically figure fuel tax savings  Diagnostic Trouble Codes  MIL Status  Emissions Readiness Monitors - Check remotely if vehicles are ready for emissions certification  Brake Switch Status and Seatbelt Fastened available on most Ford & GM trucks/vans  Other parameters available on a custom basis LDVDSV2-1587_2313DS Page 2 Additional Features  Outputs OBDII data in a J1708 data format  Ignition-On Signal Output  Status LED’s for vehicle connection and power Red Green Red Actual State LED LED LED (Power) (Activity) (Debug) 1 On On Off Normal operation 2 On SB Off Detecting vehicle 3 Off FB Off Database version mismatch Customer Description 4 5 6 7 Off Off Off Off SB VSB Off On Off VSB Off FB 8 Off Off FB Error with EMM code Normal operation Detecting vehicle Database needs to be updated Update in progress Device asleep Device unpowered Firmware needs to be updated Update System Manager 9 Off Off FB EMM checking CRC of Images Wait 10 seconds if state does not change see 8 10 Off SB FB Error writing/reading to/from flash during update Restart update of current component Update in progress Device asleep Device unpowered Error FPGA Image Invalid LED state descriptions:  On (LED_ON): lit, solid  Off (LED_OFF): unlit  FB (LED_FAST): Alternating on-off; 125ms on, 125ms off  SB (LED_SLOW): Alternating on-off; .5 sec on, .5 sec off  VSB (LED_VERY_SLOW): Alternating on-off; .25 sec on, 2 sec off      Automatic low power mode senses when vehicle speed & engine speed is zero. Automatic disconnect when technician scan tool is connected (Requires separate OBDII Y-Cable) Proprietary vehicle detection algorithm and embedded database lets the same hardware work on all compliant vehicles Wide Operating Temperature: -40 to 85 ºC (-40 to 185 ºF) Low Power Consumption: 2W in Operating Mode; 0.15W in Automatic Sleep Mode (Key Off) LDVDSV2-1587_2313DS Available Form Factors External Box Vehicle Bus Connection: DB15 female Pin 1 ISO9141 K/ Pins 4, 5: J1850-, J1850+ Pin 6, 7 Ground Pin 9 Vehicle unswitched Vbat Pin 10 ISO9141 L Pin 11 Vehicle Vbat to external scan tool Pin 12 CAN Low Pin 13 CAN High RS-232 Connection: DB9 female, DCE Pin 1 Optional Vbat Power in or VBat power out (2 separate build options) Pin 3 J1708Pin 7 Ground Pin 8 J1708+ Dimensions: 4.1 x 1.7 x 0.8 in (104.1 x 43.2 x 20.3 mm) Operating Voltage Range: 8 to 30 VDC Calculated MTBF: 111,440 Hours Page 3 LDVDSV2-1587_2313DS EMC Testing Radiated RF Interference: Load Dump and Transient Protection ESD Immunity Page 4 SAE J1113/41 SAE J1113/11 SAE J1113/13 Environmental Testing Temperature Test: Ten (10) temperature cycles as follows with unit operating normally 1. Room (25ºC) to Tmin in 15 minutes. 2. Soak at Tmin 1 Hour with power removed from unit 3. Start unit at Tmin, confirm successful start by executing a command/response. Power-down unit. Maintain unit un-powered for one minute between power-ups. 4. Repeat Step 3 three times 5. Start unit at Tmin and ramp Tmin to Tmax in 30 minutes 6. Operate at Tmax for 1 hour 7. Ramp Tmax to Tmin in 15 minutes 8. Repeat steps 1 through 7 nine times for a total of 10 cycles: a. 5 cycles at Vmin input b. 5 cycles at Vmax input Vibration Test: IEC 60068-2-6 10 sweeps of 10 to 500 to 10Hz at rate 0.5 oct/min. each axis. Level to be 10 to 36Hz, 0.06 in DA 36 to 500Hz, 4g’s Unit must remain operational during and after the test. Shock Test: IEC 60068-2-27 18 to 50g’s, 11ms, ½ sine pulses, 3 each direction each axis Unit must remain operational during and after the test. Drop Test: IEC 60068-2-32 10 Freefall drops from 1 meter onto concrete surface. Drop 1 time one each face (6), 1 on a corner and the 3 edges of this corner. The drop unit shall return to normal operation without physical damage.