BB-WSD2C06010

Wzzard™ Mesh Wireless Sensors – for Industrial Applications BB-WSD2x series www.advantech.com PRODUCT FEATURES + Ultra-low power 802.15.4e SmartMesh® IP technology + Communicates with SmartSwarm-342 gateway via scalable and reliable wireless mesh networks + Connect to most any industry standard sensors + Rugged, IP67 rated, fiber reinforced polyester PBT enclosure + MQTT and JSON IoT protocol to application platform + Sensor interface cable and antenna included + UL Listed C1/D2 for hazardous locations (conduit models only) Wireless Connectivity Where You Need It The Wzzard™ intelligent wireless sensor platform creates a complete, quick and easy connectivity stack between your sensors and application – on your network or the Internet. The platform uses Wzzard mesh sensor edge nodes and a wireless 802.15.4e SmartMesh IP network to transmit sensor data to a SmartSwarm Gateway. The gateway can connect to the Internet via wired connections or cellular data networks and communicate with application platforms using the MQTT IoT protocol and JSON data formats. Wzzard mesh wireless sensor nodes can accommodate virtually any industry-standard external sensors. Connections can be made via M12 connector or conduit fitting. The nodes provide a wide variety of sensor interface options, including general purpose analog input, digital input/output and thermocouple. All nodes contain an internal temperature sensor. Secure, Reliable and Highly Scalable Wireless Networking The 802.15.4e Wzzard platform uses mesh networking and timesynchronized channel hopping to provide up to 99.999% connectivity, even in the most demanding RF environments. New nodes may be added at any time and the SmartMesh IP network will dynamically self-configure as new nodes are added or removed. Easy Configuration and Installation Configuration of the Wzzard sensor platform is easy via the SmartSwarm Gateway. Nodes can be configured with scaling information, eng. units, friendly names, geo-location and other descriptive information. The platform simplifies physical installation, too. Nodes can be attached to any surface via mounting ear flanges and screws or the embedded magnetic base. Magnetic mount is convenient for RF link location determination or other purposes. (Permanent use of the magnetic mount is not approved for UL installations.) The IP67 rated, fiber reinforced polyester PBT housing makes the units deployable in any industrial or commercial environment. Intelligence at the Network Edge The Wzzard wireless platform places intelligence at the network edge. The Wzzard mesh wireless sensor nodes can be configured to communicate data only when specified threshold or alert levels are exceeded. When reporting, they can associate useful information like geo-location, device name and uptime. This eliminates unnecessary network traffic, eases the processing burden on upstream resources and cuts the cost of cellular data plans when the gateway is using the cellular data network. Thanks to low-power wireless technology and programmable time synchronization, the Wzzard mesh wireless sensor nodes can operate for many years on battery power. SPECIFICATIONS POWER Internal (2) 3.6V 2400 mAH Lithium Thionyl Chloride AA Batteries Battery Life Optional External Input Voltage SENSOR POWER OUT Switched Vbat Switched Vref MECHANICAL >5 years – based on 1 min. sensor sampling and reporting Connection Options Sensors External Antenna (included) Mounting Options Enclosure Weight TECHNOLOGY Wireless Protocols LED ENVIRONMENTAL Installation 10-30 VDC @ 40mA peak Battery Power – Turned on at time of measurement (20 mA max) 3.3V (+/- 0.1%) – Turned on at time of measurement (20 mA max) Conduit (UL Type 3 outdoor approved): 12.7mm (0.5 in) - includes (1) one sensor interface cable - 8-pin 26-gauge wire harness, 1.8 m (6 ft) (Model# BB-WSCACO-6) M12 connector (Not UL rated for outdoor installations.) Analog Input (0 -10 VDC, 0 - 20 mA, 4 - 20 mA) Digital Input (0 - 48 VDC) Digital Input Frequency 1-1K Hz (accuracy +/- 1 Hz) Digital Input Counter Integrated Temperature Thermocouple (J, K, N, R, S, T, B, E) Digital Output, Sinking, up to 100mA @ 30VDC RP-SMA, Omni-directional, 3.8 dBi, 2.4 GHz (included) Dimensions: 194 mm (7.64 in) (4) Mounting Ears, M5 (#10) screws (UL approved option) Magnetic Mounting (via internal enclosure magnet) Pull Force 2.13 kg (4.7 lb) Note: Magnetic mounting (all models) not rated for UL installations. IP67 rated fiber reinforced polyester PBT 0.34 kg (0.75 lb) 802.15.4e, SmartMesh IP MQTT, JSON Network Connectivity Indoor/Outdoor Note: M12 models are rated for outdoor use (except in UL installations). Operating Temperature -40 to +80 °C (-40 to +176 °F) Storage Temperature -40 to +85 °C (-40 to +185 °F) Operating Humidity 0 to 95% Non-condensing WIRELESS SECURITY Device Authentication 128-bit, AES-based Encryption – with multiple keys Message Integrity Check (MIC) Synchronized Key Changeovers Customized Key Rotation All product specifications are subject to change without notice. BB-WSD2x_WzzardWirelessSensorNodes-Ind_4019ds Advantech B+B SmartWorx, 707 Dayton Road, PO Box 1040 Ottawa, IL 61350 USA 1 (800)346-3119/Toll Free | orders@advantech-bb.com | support@advantech-bb.com Wzzard™ Mesh Wireless Sensors – for Industrial Applications BB-WSD2x series ORDERING INFORMATION MODEL NUMBER DESCRIPTION BB-WSD2C21150 Industrial Cooler/HVAC Node CONNECTOR INCLUDES 2 Analog Inputs, 1 Digital Input, 1 Digital Output, 2 Thermocouples, Conduit 2 Thermistors, Internal Temperature BB-WSD2C06010 Industrial Digital Input Node Conduit 6 Digital Inputs, Internal Temperature BB-WSD2C31010 Industrial Power Monitor Node Conduit 3 Analog Inputs, 1 Digital Input, Internal Temperature Indoor / Outdoor, w/ mounting ear installation BB-WSD2M06010 Industrial Digital Input Node M12 6 Digital Inputs, Internal Temperature No (M12 connector not UL.) BB-WSD2M31010 Industrial Power Monitor Node M12 3 Analog Inputs, 1 Digital Input, Internal Temperature No (M12 connector not UL.) M12 2 Analog Inputs, Vbat measurement, 1 Digital Input, Internal Temperature, No (M12 connector not UL.) Switched Vbat Power Out (2 sec.) 12 Analog Inputs, Vref measurement, 1 Digital Input, Internal Temperature, No (M12 connector not UL.) Switched 3.3V Power Out (100 ms) BB-WSD2M3101P2K Industrial Power Monitor Node BB-WSD2M3101R100 Industrial Power Monitor Node M12 UL LISTED C1/D2 Indoor / Outdoor, w/ mounting ear installation (pending) ACCESSORIES - sold separately MODEL NUMBER BB-ACH2-DBAT-DP002 BB-ZXTMT BB-WSCACO-6 BB-WSCAM12-6 BB-JC10F50-V BB-JC24S250-V BB-JC36S500-V BB-WCD-TM2M BB-WTJ-10-36-TT BB-HS-104T2505402 BB-WSDCBL-ACL-2 BB-T9602-3-A-1-G2 DESCRIPTION Antenna - dipole, 2.4/5 GHz, 2dBi, RPSMA, rubber duck, hinged (Replacement; 1 included with all nodes.) Kit - Zlinx™ Xtreme conduit cable gland & hub Sensor interface cable, 8-pin 26-gauge wire harness, 1.8m (6ft) (Replacement; 1 included with conduit nodes.) Cable - M12 pigtail, 8-pin, 1.8 m (6 ft) Sensor - 50A clamp-on AC current, 0-5VDC Out Sensor - 250A clamp-on AC current, 0-5VDC Out Sensor - 500A clamp-on AC current, 0-5VDC Out Thermistor cable Sensor - J-type thermocouple, #10 mounting hole, ungrounded Sensor - low power vibration/temperature sensor, 250mV/g M12 signal conditioning cable for model# BB-HS-104T2505402 Sensor cable - temperature/humidity, 1.8 m (6 ft) COMPATIBLE NODES All Industrial Nodes All Conduit Nodes All Conduit Nodes All M12 Nodes All Analog Input Nodes All Analog Input Nodes All Analog Input Nodes BB-WSD2C21150 BB-WSD2C21150 BB-WSD2M3101P2K BB-WSD2M3101P2K BB-WSD2M3101R100 MECHANICAL DIAGRAM Units = [Millimeters] Inches Advantech B+B SmartWorx, 707 Dayton Road, PO Box 1040 Ottawa, IL 61350 USA (800)346-3119/Toll Free | orders@advantech-bb.com | support@advantech-bb.com Wzzard™ Mesh Wireless Sensors – for Industrial Applications BB-WSD2x series SENSOR INTERFACE SPECIFICATIONS DIGITAL INPUTS Voltage Range VIL VIH Pull-up Current Type Isolation RATE/FREQUENCY INPUTS Frequency COUNTER INPUT Counter Inputs Channels ANALOG INPUTS Analog Inputs Input Range Resolution Input Load Resistance Accuracy Variance THERMOCOUPLE INPUT Types Supported Accuracy 0-48 VDC 0.4 V, maximum 2.5 V, minimum 65 uA Sinking input (NPN) None Performs a 1 second measurement at each measurement/publish interval Digital input frequency: 1 - 1KHz (accuracy +/- 1 Hz) Uses falling edge or rising edge – based on Invert Enabled Setting 1 Actively counts either falling edge (Invert Enabled) or rising edge (Invert Disabled) Can use a multiplier to convert to a unit type or count Shared with digital inputs Rolls over at 999999.9 2 or 3 (model dependent) 0-10 VDC, 0-20 mA (software selectable) 0.3 mV/1.3 uA 59 K Ohms +/-25mV +/-0.05 mA J, K, N, R, S, T, B, E THERMOCOUPLE Type B Type E Type J Type K Type N Type R Type S Type T Resolution Accuracy Variance THERMISTOR INPUT Type Supported Temperature Range Resolution Accuracy Accuracy Variance DIGITAL OUTPUTS Voltage Range Output Type Output Current Protection Isolation Temperature Range +95 to +1798 °C -200 to +1000 °C -210 to +1200 °C -200 to +1372 °C -200 to +1300 °C -50 to +1768 °C -50 to +1768 °C -200 to +400 °C Ambient Temperature Worst Case RSS Error Probe Error B Type @ +25 °C 9.4 °C 0.5% of T, 0.25% of T B Type @ -40 to +85 °C 47.1 °C 0.5% of T, 0.25% of T C Type @ +25 °C 1.4 °C 1.7 °C, 1 °C C Type @ -40 to +85 °C 5.2 °C 1.7 °C, 1 °C J Type @ +25 °C 1.5 °C 2.2 °C, 1.1 °C J Type @ -40 to +85 °C 5.9 °C 2.2 °C, 1.1 °C K Type @ +25 °C 1.8 °C 2.2 °C, 1.1 °C K Type @ -40 to +85 °C 7.3 °C 2.2 °C, 1.1 °C N Type @ +25 °C 2.3 °C 2.2 °C, 1.1 °C N Type @ -40 to +85 °C 10.3 °C 2.2 °C, 1.1 °C R Type @ +25 °C 5.4 °C 1.5 °C, 0.6 °C R Type @ -40 to +85 °C 26.0 °C 1.5 °C, 0.6 °C S Type @ +25 °C 6.7 °C 1.5 °C, 0.6 °C S Type @ -40 to +85 °C 33.0 °C 1.5 °C, 0.6 °C T Type @ +25 °C 1.7 °C 1 °C, 0.5 °C T Type @ -40 to +85 °C 7.2 °C 1 °C, 0.5 °C 0.0078 °C 0.20% of full-scale reading (0.25%, maximum) 10K NTC -40 to +85 °C 0.01 °C THERMISTOR Typ. Error Worst Case Error 853 ppm (0.1 °C) 4103 ppm Maximum +/- 0.5 °C over -40 to +85 °C temperature range Worst Case RSS Error 2101 ppm Probe Error n/a 0-30 VDC Open drain Not to be less than 100 mA Current limit protection None Advantech B+B SmartWorx, 707 Dayton Road, PO Box 1040 Ottawa, IL 61350 USA (800)346-3119/Toll Free | orders@advantech-bb.com | support@advantech-bb.com Wzzard™ Mesh Wireless Sensors – for Industrial Applications BB-WSD2x series INTEGRATED SENSORS TEMPERATURE Offset Slope Error CONDITIONS Temperature Offset Error @ 25 °C - SMARTMESH IP 802.15.4E RADIO SPECIFICATIONS PARAMETER Frequency Band Number of Channels Channel Separation Channel Clear Frequency Modulation Raw Data Rate Range Receiver Sensitivity Output Power CONDITIONS MINIMUM TYPICAL +/- 0.25 +/- 0.033 TYPICAL UNITS °C °C / °C MINIMUM 2.400 TYPICAL MAXIMUM 2.4835 UNITS GHz Where k = 11 to 25, as defined by IEEE 802.4.15 IEEE 802.15.4 Direct Sequence Spread Spectrum (DSSS) 25 °C, 50% RH, +2dBi Omni-Directional Antenna, Antenna 2m above ground Indoor Outdoor Packet Data Error Rate (PER) = 1% P.E.R. = 50% Delivered to a 50 Ω load 15 5 2405 + 5*(k-11) MHz MHz 250 kbps 100 300 m m dBm dBm dBm -93 -95 8 THIONYL CHLORIDE LITHIUM BATTERIES (2 supplied with product) CHARACTERISTICS Temperature Range Nominal Capacity Nominal Voltage Diameter Height CONDITIONS -40 to +85 °C 2.4 Ah 3.6 V 14.5mm 50.5mm *Potential Hazard: Do not recharge, crush, disassemble or heat above 100 °C (212 °F). APPROVALS, DIRECTIVES, STANDARDS (WSD2M31010, WSD2C21150, WSD2C31010) CE - DIRECTIVES 2014/35/EU 2014/53/EU 2011/65/EU 2012/19/EU CE - EMC ETSI EN 300 328 v2.1.1 ETSI EN 301 489-1 v2.1.1 ETSI EN 301 489-17 v3.2.0 EN 55032+AC, Class A EN 55024 CE - SAFETY EN/IEC 61010-1 (3rd ed.) EN/IEC 61010-2-201 (1st ed.) CE - RF EXPOSURE EN 62479 Low Voltage Directive (LVD) Radio Equipment Directive (RED) Reduction of Hazardous Substances Directive (RoHS) Waste Electrical and Electronic Equipment Directive (WEEE) EMC & Radio Spectrum Matters (ERM) Wideband Transmission Systems, 2.4 GHz ISM Band Applied in accordance with the specific requirements of: EMC and Radio Spectrum Matters: Broadband Data Systems Information Technology Equipment (ITE) - RF Emissions Information Technology Equipment (ITE) - Immunity Characteristics - Limits and Methods of Measurement Safety requirements for electrical equipment for measurement, control, and laboratory use (general requirements). Particular requirements for control equipment Assessment of compliance of low power electronics and electrical equipment with basic restrictions related to human exposure to electromagnetic fields (10 MHz to 300 GHz) ENVIRONMENTAL IEC 60068-2-6 Sine Vibration: 4G, 10-500 Hz, 0.06 in. displacement IEC 60068-2-27 Mechanical Shock: 50G, 11ms, 18 pulses FCC, IC FCC Part 15 Class A, FCC Part 15.247 ICES-003 ITE Emissions for Canada UL (All models w/ mounting ear installation; M12 model indoors only.) UL/CSA Class 1/Division 2, Groups A, B, C, D (Conduit Models Only) Advantech B+B SmartWorx, 707 Dayton Road, PO Box 1040 Ottawa, IL 61350 USA (800)346-3119/Toll Free | orders@advantech-bb.com | support@advantech-bb.com