User Manual
PCE-5026
LGA1155
Intel® Core™i7/i5/i3/Pentium®
PICMG 1.3 System Host Board
with DDR3 / SATA2.0 / USB2.0 /
Single GbE LAN
Copyright
The documentation and the software included with this product are copyrighted 2012
by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right
to make improvements in the products described in this manual at any time without
notice. No part of this manual may be reproduced, copied, translated or transmitted
in any form or by any means without the prior written permission of Advantech Co.,
Ltd. Information provided in this manual is intended to be accurate and reliable. However, Advantech Co., Ltd. assumes no responsibility for its use, nor for any infringements of the rights of third parties, which may result from its use.
Acknowledgements
AMIBIOS is a trademark of American Megatrends Inc.
Intel®, Intel® Core™ i7/i5/i3, Pentium® and Xeon® are trademarks of Intel® Corporation.
Nuvoton is a trademark of Nuvoton Technology Corp.
All other product names or trademarks are the properties of their respective owners.
Product Warranty (2 years)
Advantech warrants to you, the original purchaser, that each of its products will be
free from defects in materials and workmanship for two years from the date of purchase.
This warranty does not apply to any products which have been repaired or altered by
persons other than repair personnel authorized by Advantech, or which have been
subject to misuse, abuse, accident or improper installation. Advantech assumes no
liability under the terms of this warranty as a consequence of such events.
Because of Advantech’s high quality-control standards and rigorous testing, most of
our customers never need to use our repair service. If an Advantech product is defective, it will be repaired or replaced at no charge during the warranty period. For outof-warranty repairs, you will be billed according to the cost of replacement materials,
service time and freight. Please consult your dealer for more details.
If you think you have a defective product, follow these steps:
1. Collect all the information about the problem encountered. (For example, CPU
speed, Advantech products used, other hardware and software used, etc.) Note
anything abnormal and list any onscreen messages you get when the problem
occurs.
2. Call your dealer and describe the problem. Please have your manual, product,
and any helpful information readily available.
3. If your product is diagnosed as defective, obtain an RMA (return merchandise
authorization) number from your dealer. This allows us to process your return
more quickly.
4. Carefully pack the defective product, a fully-completed Repair and Replacement
Order Card and a photocopy proof of purchase date (such as your sales receipt)
in a shippable container. A product returned without proof of the purchase date
is not eligible for warranty service.
5. Write the RMA number visibly on the outside of the package and ship it prepaid
to your dealer.
PCE-5026 User Manual
Part No. 2006502610
Edition 1
Printed in China
October 2012
ii
Declaration of Conformity
FCC Class A
Note: This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in
which case the user will be required to correct the interference at his own expense.
Caution! There is a danger of a new battery exploding if it is incorrectly installed.
Do not attempt to recharge, force open, or heat the battery. Replace the
battery only with the same or equivalent type recommended by the manufacturer. Discard used batteries according to the manufacturer's
instructions.
A Message to the Customer
Advantech Customer Services
Each and every Advantech product is built to the most exacting specifications to
ensure reliable performance in the harsh and demanding conditions typical of industrial environments. Whether your new Advantech equipment is destined for the laboratory or the factory floor, you can be assured that your product will provide the
reliability and ease of operation for which the name Advantech has come to be
known.
Your satisfaction is our primary concern. Here is a guide to Advantech’s customer
services. To ensure you get the full benefit of our services, please follow the instructions below carefully.
Technical Support
We want you to get the maximum performance from your products. So if you run into
technical difficulties, we are here to help. For the most frequently asked questions,
you can easily find answers in your product documentation. These answers are normally a lot more detailed than the ones we can give over the phone.
So please consult this manual first. If you still cannot find the answer, gather all the
information or questions that apply to your problem, and with the product close at
hand, call your dealer. Our dealers are well trained and ready to give you the support
you need to get the most from your Advantech products. In fact, most problems
reported are minor and are able to be easily solved over the phone.
In addition, free technical support is available from Advantech engineers every business day. We are always ready to give advice on application requirements or specific
information on the installation and operation of any of our products.
iii
PCE-5026 User Manual
Memory Compatibility
PCE-5026 Compatible Memory
Brand
Capacity Speed Type ECC Vendor PN
Memory
Advantech PN
1GB
1066
DDR3 N
TS128MLK64V1U
SEC K4B1G0846G‐BCH9
96D3‐1G1066NN‐TR
2GB
1066
DDR3 N
TS256MLK64V1U
SEC K4B1G0846G‐BCH9
96D3‐2G1066NN‐TR
1GB
1333
DDR3 N
TS128MLK64V3U
ELPIDA EDJ1108BFBG‐DJ‐F
96D3‐1G1333NN‐TR
Transcend 2GB
1333
DDR3 N
TS256MLK64V3U
SEC K4B1G0846G‐BCH9
96D3‐2G1333NN‐TR4
4GB
1600
DDR3 N
TS512MLK64V6N
MICRON IUM22 D9PFJ
N/A
2GB
1600
DDR3 N
TS256MLK64V6N
MICRON IRM72 D9PFJ
N/A
8GB
1600
DDR3 N
TS1GLK64V6H
Micron IZD27 D9PBC 512x8
N/A
1GB
1066
DDR3 N
78.01GC3.420
ELPIDA J1108BDBG‐DJ‐F (128x8)
96D3‐1G1066NN‐AP
2GB
1066
DDR3 N
78.A1GC3.421
ELPIDA J1108BDBG‐DJ‐F (128x8)
96D3‐2G1066NN‐AP
4GB
1066
DDR3 N
78.B1GDJ.AF1
HYNIX H5TQ2G83BFR‐H9C
N/A
DDR3 N
78.01GC6.AF0
1GB
Apacer
Kingston
1333
1333
H5TQ1G83DFR‐H9C
96D3‐1G1333NN‐AP1
H5TQ1G83TFR‐H9C
2GB
1333
DDR3 N
78.A1GDE.4200C
ELPIDA J2108BCSE‐DJ‐F
96D3‐2G1333NN‐AP2
2GB
1333
DDR3 N
78.A1GDE.AF00C
Hynix H5TQ2G838FR(256x8)
96D3‐2G1333NN‐AP1
4GB
1333
DDR3 N
78.B1GDE.AF1
HYNIX H5TQ2G83BFR‐H9C
96D3‐4G1333NN‐AP
8GB
1333
DDR3 N
78.C1GEP.4210C
ELPIDA J4208BASE‐DJ‐F 512x8
96D3‐8G1333NN‐AP
8GB
1600
DDR3 N
78.C1GET.ATF0C
Micron 2FD27 D9PCP (512x8)
96D3‐8G1600NN‐APL
4GB
1333
DDR3 N
KVR1333D3N9/4G
KINGSTON
D2568JENCPGD9U(512x64)
N/A
2GB
1600
DDR3 N
D3US56081XH12AA
SEC 113 HCK0 K4B2G0846C 256x8
N/A
4GB
1600
DDR3 N
D3US56082XH12AA
SEC 113 HCK0 K4B2G0846C 256x8
N/A
8GB
1600
DDR3 N
XQ16B8N8GS‐9‐AV
SEC K4B4G0846B (512x8)
N/A
DSL
ATP
Specification Comparison
Part Number
PCH
Memory
PCE-5026VG-00A1E
H61
Non-ECC PCE-5BXX
PCE-5026 User Manual
Backplane
LAN VGA DVI-D
COM
SATA USB
Raid iAMT
2.0
2.0
1
2
4
iv
Yes
Optional
10
N/A
N/A
Processor Support
PN
PCE-5026VG-00A1E
Processor
Core i7-3770
Yes
Core i7-2600
Yes
Core i5-3550S
Yes
Core i5-2400
Yes
Core i3-3220
Yes
Core i3-2120
Yes
Pentium G2120
Yes
Pentium G850
Yes
Celeron G540
Yes
Backplane Support Matrix Table
Backplane
Model
PCE-5026VG-00A1E
Note!
PCE-5XXX
PCE-7XXX
Yes
-
If PCE-5026 is used on different backplanes which have different PCIe
configurations the message below will be displayed the first time the unit
is powered on. The user has to turn off AC power and then turn it back
on for PCIe re-configuration.
Caution! PCIe configuration error! Please turn off AC power before re-configuration.
v
PCE-5026 User Manual
Initial Inspection
Before you begin installing your motherboard, please make sure that the following
materials have been shipped:
1 PCE-5026 PICMG 1.3 System Host Board
1 PCE-5026 startup manual
1 CD with utility
2 Serial ATA HDD data cable
2 Serial ATA HDD power cable
1 COM + printer ports cable kit
1 4-port USB cable kit
Keyboard and mouse Y cable
1 jumper package
1 warranty card
P/N: 1700003194
P/N: 1703150102
P/N: 1701260305
P/N: 1700008461
P/N: 1700060202
P/N: 9689000068
If any of these items are missing or damaged, contact your distributor or sales representative immediately. We have carefully inspected the PCE-5026 mechanically and
electrically before shipment. It should be free of marks and scratches and in perfect
working order upon receipt. As you unpack the PCE-5026, check it for signs of shipping damage. (For example, damaged box, scratches, dents, etc.) If it is damaged or
it fails to meet the specifications, notify our service department or your local sales
representative immediately. Also notify the carrier. Retain the shipping carton and
packing material for inspection by the carrier. After inspection, we will make arrangements to repair or replace the unit.
PCE-5026 User Manual
vi
Contents
Chapter
1
Hardware Configuration......................1
1.1
1.2
1.3
1.9
1.10
1.11
1.12
1.13
Introduction ............................................................................................... 2
Features & Benefits................................................................................... 2
Specifications ............................................................................................ 3
1.3.1 System .......................................................................................... 3
1.3.2 Memory ......................................................................................... 3
1.3.3 Input/Output .................................................................................. 3
1.3.4 Graphics........................................................................................ 3
1.3.5 Ethernet LAN ................................................................................ 4
1.3.6 Industrial Features ........................................................................ 4
1.3.7 Mechanical and Environmental Specifications.............................. 4
Jumpers and Connectors .......................................................................... 4
Table 1.1: Jumper List ................................................................. 4
Table 1.2: Connectors ................................................................. 5
Board Layout: Jumper and Connector Locations...................................... 6
Figure 1.1 Jumper and Connector Locations............................... 6
Block Diagram........................................................................................... 7
Figure 1.2 PCE-5026 Block Diagram........................................... 7
Safety Precautions .................................................................................... 7
Jumper Settings ........................................................................................ 8
1.8.1 How to Set Jumpers...................................................................... 8
1.8.2 BIOS CMOS (JCMOS1)................................................................ 8
Table 1.3: Clear BIOS CMOS/Data (JCMOS1) ........................... 8
1.8.3 Watchdog Timer Output (JWDT1) ................................................ 9
Table 1.4: Watchdog Timer Output (JWDT1) .............................. 9
Table 1.5: H/W Monitor Alarm (JOBS1) ..................................... 9
System Memory ...................................................................................... 10
Memory Installation Procedures.............................................................. 10
Cache Memory........................................................................................ 10
Processor Installation.............................................................................. 10
Processor Cooler Installation .................................................................. 12
2
Connecting Peripherals ....................13
2.1
2.2
2.3
2.4
2.5
2.6
2.7
2.8
Introduction ............................................................................................. 14
Parallel Port (LPT1)................................................................................. 14
USB Ports (USB12, USB34, USB5, USB6) ............................................ 14
VGA Connectors (VGA1) ........................................................................ 15
Serial Ports (COMD1 & COM2) .............................................................. 15
PS/2 Keyboard and Mouse Connector (KBMS1/KBMS2)....................... 16
CPU Fan Connector (CPUFAN1)............................................................ 16
Front Panel Connectors (JFP1, JFP2 & JFP3) ....................................... 17
2.8.1 ATX Soft Power Switch (JFP1) ................................................... 17
2.8.2 Reset Connector (JFP1) ............................................................. 17
2.8.3 HDD LED Connector (JFP2)....................................................... 17
2.8.4 External speaker (JFP2) ............................................................. 18
2.8.5 Power LED and Keyboard Lock (JFP3) ...................................... 18
Table 2.1: PS/2 or ATX Power Supply LED Status ................... 18
H/W Monitor/Watchdog Timer/Infrared ................................................... 18
2.9.1 H/W Monitor Alarm (JOBS1)....................................................... 19
2.9.2 Watchdog Timer (JWDT1) .......................................................... 19
2.9.3 Infrared Interface (JIR1).............................................................. 19
LAN Port (LAN1) ..................................................................................... 19
Table 2.2: LAN LED Indicators .................................................. 19
1.4
1.5
1.6
1.7
1.8
Chapter
2.9
2.10
vii
PCE-5026 User Manual
2.11
2.15
2.16
High Definition Audio Module Interface (HDAUD1) ................................ 20
Figure 2.1 Jumper and connector locations of PCA-AUDIOHDA1E ..................................................................... 21
GPIO Header (GPIO1)............................................................................ 22
Case Open Connector (JCASE1) ........................................................... 22
Front Panel LAN Indicator Connector (LANLED1).................................. 23
Table 2.3: LAN LED Indicators.................................................. 23
Serial ATA Interface (SATA1~SATA4).................................................... 24
LPC Extension Interface (LPC1)............................................................. 24
3
AMI BIOS Setup................................. 25
3.1
Introduction ............................................................................................. 26
Figure 3.1 Setup Program Initial Screen ................................... 26
Entering Setup ........................................................................................ 27
3.2.1 Main Setup.................................................................................. 27
Figure 3.2 Main Setup Screen................................................... 27
3.2.2 Advanced BIOS Features Setup................................................. 28
Figure 3.3 Advanced BIOS Features Setup Screen.................. 28
Figure 3.4 Advantech BIOS Update V1.3.................................. 29
Figure 3.5 PCI Subsystem Settings........................................... 30
Figure 3.6 PCI Express Settings ............................................... 31
Figure 3.7 ACPI Settings ........................................................... 32
Figure 3.8 Trust Computing....................................................... 33
Figure 3.9 S5 RTC Configuration .............................................. 34
Figure 3.10CPU Configuration ................................................... 34
Figure 3.11SATA Configuration.................................................. 35
Figure 3.12Intel Trusted Execution Technology Configuration... 36
Figure 3.13USB Configuration.................................................... 37
Figure 3.14Smart Settings.......................................................... 38
Figure 3.15Super I/O Configuration............................................ 38
Figure 3.16Serial Port 1 Configuration ....................................... 39
Figure 3.17Serial Port 2 Configuration ....................................... 39
Figure 3.18Parallel Configuration ............................................... 40
Figure 3.19PC Health Status...................................................... 41
Figure 3.20CPU PPM Configuration........................................... 42
3.2.3 Chipset........................................................................................ 43
Figure 3.21Chipset ..................................................................... 43
Figure 3.22PCH I/O Configuration.............................................. 43
Figure 3.23PCI Express Configuration ....................................... 44
Figure 3.24USB Configuration.................................................... 45
Figure 3.25PCH Azalia Configuration......................................... 46
Figure 3.26System Agent (SA) Configuration ............................ 47
Figure 3.27Graphics Configuration............................................. 48
Figure 3.28NB PCIe Configuration ............................................. 49
Figure 3.29Memory Information ................................................. 50
3.2.4 Boot ............................................................................................ 50
Figure 3.30 Boot ......................................................................... 50
3.2.5 Security....................................................................................... 51
Figure 3.31Security .................................................................... 51
3.2.6 Save & Exit ................................................................................. 52
Figure 3.32Save & Exit............................................................... 52
2.12
2.13
2.14
Chapter
3.2
Chapter
4
Chipset Software Installation Utility 55
4.1
4.2
4.3
Before You Begin.................................................................................... 56
Introduction ............................................................................................. 56
Windows® XP / Windows® 7 Driver Setup............................................. 57
PCE-5026 User Manual
viii
Chapter
5
Integrated Graphic Device Setup .....59
5.1
5.2
Introduction ............................................................................................. 60
Windows XP/Windows 7 Driver Setup .................................................... 60
6
LAN Configuration.............................61
6.1
6.2
6.3
6.4
Introduction ............................................................................................. 62
Features .................................................................................................. 62
Installation ............................................................................................... 62
Win XP /Win 7 Driver Setup (LAN).......................................................... 62
7
Intel ME ...............................................63
7.1
7.2
Introduction ............................................................................................. 64
Installation ............................................................................................... 64
Appendix A
Programming the Watchdog Timer..65
A.1
Introduction ............................................................................................. 66
A.1.1 Watchdog Timer Overview.......................................................... 66
A.1.2 Programming the Watchdog Timer ............................................. 66
Table A.1: Watchdog Timer Registers ....................................... 67
A.1.3 Example Program ....................................................................... 68
Appendix B
I/O Pin Assignments..........................73
B.1
Parallel Port Connector (LPT1) ............................................................... 74
Table B.1: Parallel port Connector (LPT1)................................. 74
VGA Connector (VGA1) .......................................................................... 74
Table B.2: VGA Connector (VGA1) ........................................... 74
RS-232 Seral Port (COMD1)................................................................... 75
Table B.3: COM Connector (COMD1) ....................................... 75
RS-232 Serial Port (COM2) .................................................................... 75
Table B.4: RS-232 Serial Port (COM2)...................................... 75
USB 2.0 Header (USB12 & USB34) ....................................................... 76
Table B.5: USB Header (USB12 & USB34)............................... 76
PS/2 Keyboard/Mouse Connector (KBMS1) ........................................... 76
Table B.6: PS/2 Keyboard/Mouse Connector (KBMS1) ............ 76
External Keyboard Connector (KBMS2) ................................................. 77
Table B.7: External Keyboard Connector (KBMS2)................... 77
CPU Fan Power Connector (CPUFAN1) ................................................ 77
Table B.8: CPU Fan Power Connector (CPUFAN1).................. 77
Power LED and Keyboard Lock Connector (JFP3 / PWR_LED & KEY
LOCK) ..................................................................................................... 77
Table B.9: Power LED and Keyboard Lock Connector (JFP3 /
PWR_LED & KEY LOCK)......................................... 77
External Speaker Connector (JFP2 / SPEAKER) ................................... 78
Table B.10:External Speaker Connector (JFP2 / SPEAKER)..... 78
Reset Connector (JFP1 / RESET) .......................................................... 78
Table B.11:Reset Connector (JFP1 / RESET)............................ 78
HDD LED (JFP2 / HDDLED)................................................................... 78
Table B.12:HDD LED (JFP2 / HDDLED) .................................... 78
ATX Soft Power Switch (JFP1 / PWR_SW) ............................................ 79
Table B.13:ATX Soft Power Switch (JFP1 / PWR_SW) ............. 79
Hi-definition Audio Link Connector (HDAUD1)........................................ 79
Chapter
Chapter
B.2
B.3
B.4
B.5
B.6
B.7
B.8
B.9
B.10
B.11
B.12
B.13
B.14
ix
PCE-5026 User Manual
B.15
B.16
B.17
B.18
B.19
B.20
B.21
B.22
Table B.14:Hi-Definition Audio Link Connector (HDAUD1) ........ 79
SM Bus Connector (JFP2 / SNMP)......................................................... 79
Table B.15:SM Bus Connector (JFP2 / SNMP) .......................... 79
LAN1 LED Connector (LANLED1) .......................................................... 80
Table B.16:LAN1 LED Connector (LANLED1) ........................... 80
GPIO Header (GPIO1)............................................................................ 80
Table B.17:GPIO Header (GPIO1) ............................................. 80
Fixed I/O Ranges Decoded by Intel PCH ............................................... 81
Table B.18:Fixed I/O Ranges Decoded by PCH......................... 81
System I/O Ports..................................................................................... 83
Table B.19:System I/O Ports ...................................................... 83
Interrupt Assignments ............................................................................. 83
Table B.20:Interrupt Assignments .............................................. 83
1 MB Memory Map.................................................................................. 84
Table B.21:1 MB Memory Map ................................................... 84
PCI Bus Map........................................................................................... 84
Table B.22:PCI Bus Map ............................................................ 84
Appendix C
Programming the GPIO .................... 85
C.1
C.2
C.3
Supported GPIO Register ....................................................................... 86
GPIO Registers....................................................................................... 86
GPIO Example Program-1 ...................................................................... 86
PCE-5026 User Manual
x
Chapter
1
Hardware
Configuration
1
1.1 Introduction
PCE-5026, id a PICMG 1.3 full size form-factor system host board, designed with an
Intel® H61 PCH for industrial applications needing high computing power and strong
I/O capability. PCE-5026 features either Intel® 22nm or 32nm manufacturing technology processors: Intel® Core™ i7/i5/i3 and Pentium® LGA1155. It comes with integrated memory and graphic controllers, supporting DDR3 1066/1333/1600* DRAM
up to 16 GB (8GB per DIMM). Within advanced silicon technology, PCE-5026 is suitable for power hungry industrial computing applications.
PCE-5026 has excellent 3D graphics processing capability and provides strong 2D
transcoding power with an embedded Intel® HD Graphics processor. With the
embedded graphics controller, there is no additional cost for discrete graphics cards.
Moreover, it also reduces system power consumption and thermal output.
PCE-5026 also has rich I/O interfaces and supports Advantech PCE-5BXX backplanes to offer various expansions such as PCI, PCI-X and PCIe interfaces. PCE5026 provides four SATA 2.0, ten USB 2.0 and two RS-232 ports for general industrial applications. With flexible I/O interfaces and powerful graphics capability, PCE5026 is an excellent, cost effective graphics or I/O oriented hardware platform.
Accompanied by outstanding performance and exceptional features, PCE-5026 is
the ideal computing solution for most industrial applications.
Note!
PCE-5026 supports PCE-5Bxx series backplane.
1.2 Features & Benefits
Features
Benefits
PCE-5026 supports Intel 3rd and 2nd
generation processors
Intel’s 3rd and 2nd generation Core i7/i5/i3/Pentium processor with quad/dual-core computing
power brings quantum-leap performance improvements.
PCE-5026 supports DDR3 1066/1333/
1600* SDRAM up to 16GB (8GB per
To provide higher memory data transmitting and
DIMM).
processing efficiency, bringing higher system per*DDR3 1600 is supported by Intel Gener- formance.
ation 3 CPU.
PCE-5026 provides one PCIe x16 to
backplane.
PCE-5026 supports up to 19 PCE-5BXX series
backplanes.
To reduce customer S/W development effort with
Fully supports Advantech SUSI APIs and more reliable S/W quality, also provides valueUtilities.
added utilities such as system monitor and
Embedded Security ID.
Internal USB type A connector
PCE-5026 User Manual
PCE-5026 supports 2 USB 2.0 type A connectors
for USB key lock or dongles to enhance system
security.
2
1.3.1 System
Note!
PCE-5026 does NOT support PATA(IDE) interface.
1.3.2 Memory
RAM:
– PCE-5026: Up to 16 GB (8GB per DIMM) in two 240-pin DIMM sockets. Supports dual-channel DDR3 1066/1333/1600* MHz SDRAM WITHOUT ECC
function.
Note!
Wrong memory configuration may cause no boot or system instability
problems.
Only Intel generation 3 CPU can support up to DDR3 1600.
1.3.3 Input/Output
Backplane Support:
Backplane Support Matrix Table:
Model
Backplane
PCE-5026VG-00A1E
PCE-5BXX
PCI bus: Four PCI masters to the backplane, 32-bit, 33 MHz PCI 2.2 compliant.
Enhanced parallel port: This EPP/SPP/ECP port can be configured for LPT1,
LPT2, LPT3 or disabled. A standard DB-25 female is connector provided.
Serial ports: Two RS-232 serial ports
PS/2 keyboard and mouse connector: One 6-pin mini-DIN connector is
located on the mounting bracket for easy connection to a PS/2 keyboard and
mouse via the Y-cable included in the package.
USB port: Supports 10 USB 2.0 ports with transfer rate of up to 480 Mbps.
(6 ports are on the CPU card and 4 ports are on the backplane)
1.3.4 Graphics
Controller: Intel® HD Graphics controller is embedded in Intel processor.
Display memory: Shared memory is subject to operating system (Please install
2 GB or above memory for basic system configuration).
CRT: Up to 2048 x 1536 resolution, 400 MHz RAMDAC.
PCI express x16 slot on the backplane: A discrete graphics card can be
installed in the PCI-E x16 slot for stronger 2D/3D graphic capability.
3
PCE-5026 User Manual
Hardware Configuration
CPU: LGA1155-socket Core i7/i5/i3 and Pentium processors
L2 Cache: Please refer to CPU specifications for detailed information.
BIOS: AMI SPI BIOS (64 Mb SPI)
System Chipset: Intel H61
SATA hard disk drive interface: Four SATA 2.0(300MB/s) ports, can be
enabled or disabled in BIOS menu.
Chapter 1
1.3 Specifications
1.3.5 Ethernet LAN
Supports single 10/100/1000 Mbps Ethernet port via the dedicated PCI Express
x1 bus which provides 500 MB/s data transmission rate.
Controller: LAN 1: Intel® 82579V
1.3.6 Industrial Features
Watchdog timer: To generate a system reset. The watchdog timer is programmable, with each unit equal to one second or one minute (255 levels).
1.3.7 Mechanical and Environmental Specifications
Operating temperature: 0 ~ 60° C (32 ~ 140° F, Depending on CPU)
Storage temperature: -40 ~ 85° C (-40 ~ 185° F)
Humidity: 20 ~ 95% non-condensing
Power supply voltage: +12 V, +5 V, +3.3 V, +5 VSB
Power consumption: Processor: Intel Core i7-3770; Memory: DDR3 1333
8 GB x 2
Voltage +12 V
+5 V
+3.3 V
+5 VSB
Current 5.87 A
0.89 A
1.96 A
0.21 A
Board size: 338.58 mm (L) x 126.39 mm (W) (13.3" x 4.98")
Board weight: 0.490 kg
1.4 Jumpers and Connectors
Connectors on the PCE-5026 system host board link it to external devices such as
hard disk drives and a keyboard. In addition, the board has a number of jumpers
used to configure the system for your application.
The tables below list the function of each of the board jumpers and connectors. Later
sections in this chapter give instructions on setting jumpers. Chapter 2 gives instructions for connecting external devices to the motherboard.
Table 1.1: Jumper List
Label
Function
JCMOS1
CMOS clear
JWDT1
Watchdog Reset
JOBS1
HW Monitor Alarm
PCE-5026 User Manual
4
Label
Function
Parallel port, supports SPP/EPP/ECP mode
LAN1
Intel 82579V for all SKUs
VGA1
D-SUB connector
KBMS1
PS/2 keyboard and mouse connector
KBMS2
External keyboard/mouse connector
COMD1
9-pin D-SUB connector
COM2
Serial port: COM2; RS-232 (9-pin Box Header)
JIR1
Infrared connector
Power LED
JFP3
(Keyboard Lock and
Power LED)
Suspend: Fast flash (ATX/AT)
JFP2
External speaker / SATA HDD LED connector
JFP1
Power Switch / Reset connector
JCASE1
Case Open
System On: ON (ATX/AT)
System Off: OFF (AT)
System Off: Slow flash (ATX)
CPUFAN1
CPU FAN connector (4-pin)
LANLED1
LAN1/2 LED extension connector
HDAUD1
HD audio extension module connector
USB12
USB port 0, 1
USB34
USB port 2, 3
USB5
USB port 4
USB6
USB port 5
SATA1
Serial ATA1
SATA2
Serial ATA2
SATA3
Serial ATA3
SATA4
Serial ATA4
CPU1
CPU Socket
DIMMA1
Memory connector channel A
DIMMB1
Memory connector channel B
GPIO1
GPIO pin header (SMD pitch-2.0 mm)
LPC1
COM port module expansion pin-header
5
PCE-5026 User Manual
Hardware Configuration
LPT1
Chapter 1
Table 1.2: Connectors
1.5 Board Layout: Jumper and Connector
Locations
CPU FAN1
JFP1 ¥3
DIMMB1
DIMMA1
DVI1
optional SATA1~4
USB12
USB34 USB5
JERP1
USB6
LANLED1
LPT1
COM2
COMD1
LAN1
VGA1
KBMS1
CPU1
HD
AUDIO1
1
JCMOS1
SPI_CN1
GPIO1
LPC1
JCASE1
JIR1+JOBS1+JWDT1
Figure 1.1 Jumper and Connector Locations
PCE-5026 User Manual
6
KBMS2
Chapter 1
1.6 Block Diagram
Hardware Configuration
Figure 1.2 PCE-5026 Block Diagram
1.7 Safety Precautions
Warning! Always completely disconnect the power cord from your chassis whenever you work with the hardware. Do not make connections while the
power is on. Sensitive electronic components can be damaged by sudden power surges. Only experienced electronics personnel should open
the PC chassis.
Caution! Always ground yourself to remove any static charge before touching the
motherboard. Modern electronic devices are very sensitive to static
electrical discharges. As a safety precaution, use a grounding wrist
strap at all times. Place all electronic components on a static-dissipative
surface or in a static-shielded bag when they are not in the chassis.
Caution! The computer is provided with a battery-powered real-time clock. There
is a danger of explosion if battery is incorrectly replaced. Replace only
with same or equivalent type recommended by the manufacturer. Discard used batteries according to manufacturer's instructions.
Caution! There is a danger of a new battery exploding if it is incorrectly installed.
Do not attempt to recharge, force open or heat the battery. Replace the
battery only with the same or equivalent type recommended by the manufacturer. Discard used batteries according to the manufacturer’s
instructions.
7
PCE-5026 User Manual
1.8 Jumper Settings
This section provides instructions on how to configure your motherboard by setting
the jumpers. It also includes the motherboard’s default settings and your options for
each jumper.
1.8.1 How to Set Jumpers
You can configure your motherboard to match the needs of your application by setting the jumpers. A jumper is a metal bridge that closes an electrical circuit. It consists
of two metal pins and a small metal clip (often protected by a plastic cover) that slides
over the pins to connect them. To “close” (or turn ON) a jumper, you connect the pins
with the clip. To “open” (or turn OFF) a jumper, you remove the clip. Sometimes a
jumper consists of a set of three pins, labeled 1, 2 and 3. In this case you connect
either pins 1 and 2, or 2 and 3. A pair of needle-nose pliers may be useful when setting jumpers.
1.8.2 BIOS CMOS (JCMOS1)
The PCE-5026 CPU card contains a jumper that can erase BIOS CMOS resetting
data about the system BIOS information. Normally this jumper should be set with
pins 1-2 closed. If you want to reset data, set JCMOS1 to 2-3 closed for just a few
seconds, and then move the jumper back to 1-2 closed. This procedure will reset the
CMOS to its last status or default setting.
Table 1.3: Clear BIOS CMOS/Data (JCMOS1)
Function
Jumper Setting
1
*Keep BIOS CMOS data
1-2 closed
Clear BIOS CMOS data
2-3 closed
* default setting
JCMOS1
PCE-5026 User Manual
8
The PCE-5026 contains a watchdog timer that will reset the CPU in the event the
CPU stops processing. This feature means the PCE-5026 will recover from a software failure or an EMI problem. The JWDT1 jumper settings control the outcome of
what the computer will do in the event the watchdog timer is triggered.
Table 1.4: Watchdog Timer Output (JWDT1)
Function
Jumper Setting
Hardware Configuration
1
* Reset
2-3 closed
*default setting
Table 1.5: H/W Monitor Alarm (JOBS1)
Function
Chapter 1
1.8.3 Watchdog Timer Output (JWDT1)
Jumper Setting
1
Enabled
2
1-2 closed
1
Disabled
2
1-2 opened
(JOBS1) is a 2-pin connector for enabling/disabling alarm while the on-board security
event is active.
9
PCE-5026 User Manual
1.9 System Memory
PCE-5026 has two 240-pin memory sockets for Non-ECC DDR3 1066/1333/1600*
memory modules with maximum capacity of 16 GB. (Maximum 8 GB for each DIMM)
Note!
PCE-5026 does NOT support registered DIMMs (RDIMMs).
1.10 Memory Installation Procedures
To install DIMMs, first make sure the two handles of the DIMM socket are in the
“open” position; e.g., the handles lean outward. Slowly slide the DIMM module along
the plastic guides on both ends of the socket. Then press the DIMM module right
down into the socket, until you hear a click. This is when the two handles have automatically locked the memory module into the correct position of the DIMM socket. To
remove the memory module, just push both handles outward, and the memory module will be ejected by the mechanism in the socket.
1.11 Cache Memory
Intel CPU supports L3 cache. Please refer to the Intel CPU data sheet for detailed
information.
1.12 Processor Installation
Warning! Without a fan or heat sink, the processor will overheat and cause damage to both the processor and the system host board computer. To
install a processor, first turn off your system.
The PCE-5026 is designed for Intel® LGA 1155 socket processors.
1. Pull the bar beside the processor socket outward and lift it.
PCE-5026 User Manual
10
Remove the socket protection cap.
3.
Align the cuts on the processor with the edges of the socket.
4.
Replace the socket cap; lower the retainer bar and clip it shut.
PCE-5026 User Manual
Hardware Configuration
11
Chapter 1
2.
5.
Finished processor installation.
1.13 Processor Cooler Installation
Purchasing PCE-5026's proprietary CPU cooler (P/N: 1960047831N001) from
Advantech is a must. Other brand CPU coolers are NOT compatible with PCE-5026.
Advantech offers a specially designed CPU cooler for PCE-5026 for better heat dissipation efficiency and enhancing rigidity of the CPU card: part number
1960047831N001. Buy it only for the PCE-5026 CPU card since it is NOT compatible
with other brand CPU coolers (it is also not compatible with Intel boxed CPU cooler).
Please install P/N 1960047831N001 CPU cooler following these instructions:
Attach the CPU cooler on CPU card by fastening four screws of the
CPU cooler into the steel back-plate on the PCB.
Note the direction of CPU cooler; it must follow the diagram shown above.
Installing a CPU cooler in the wrong direction may cause poor heat
dissipation that could damage the CPU card.
PCE-5026 User Manual
12
Chapter
2
Connecting
Peripherals
2
2.1 Introduction
You can access most of the connectors from the top of the board. If you have a number of cards installed, you may need to partially remove the card to make all the connections.
2.2 Parallel Port (LPT1)
LPT1
The parallel port is normally used to connect the motherboard to a printer. The PCE5026 includes an onboard parallel port, accessed through a 26-pin flat-cable connector, LPT1.
2.3 USB Ports (USB12, USB34, USB5, USB6)
The PCE-5026 provides up to 6 USB (Universal Serial Bus) on-board ports with complete Plug & Play and hot swap support for up to 127 external devices. These USB
ports comply with USB Specification 2.0, supporting transfer rates up to 480 Mbps
(USB2.0). The USB interface can be disabled in the system BIOS setup.
USB1,2
USB3,4 USB5
PCE-5026 User Manual
14
USB6
Chapter 2
2.4 VGA Connectors (VGA1)
This CPU card has VGA outputs that can drive conventional CRT displays. VGA1 is a
standard 15-pin D-SUB connector commonly used for VGA.
2.5 Serial Ports (COMD1 & COM2)
COM2
COMD1
The PCE-5026 offers two serial ports. These ports can connect to serial devices,
such as a communication network device.
The IRQ and address ranges for both ports are fixed. However, if you want to disable
the port or change these parameters later, you can do this in the system BIOS setup.
15
PCE-5026 User Manual
Connecting Peripherals
VGA1
2.6 PS/2 Keyboard and Mouse Connector (KBMS1/
KBMS2)
KBMS1
KBMS2
Two on-board 6-pin mini-DIN connectors (KBMS1) provide connection to PS/2 keyboard and mouse by the Y-cable (1700060202) in the package.
The on-board KBMS2 pin header provides connection to the front panel PS/2 keyboard and mouse connector of the chassis.
2.7 CPU Fan Connector (CPUFAN1)
This connector supports cooling fans of 500 mA (6 W) or less, and it also supports
smart fan control when using 4-pin or 3-pin cooler.
CPUFAN1
PCE-5026 User Manual
16
There are several external switches to monitor and control the PCE-5026.
JFP1~3
If your computer case is equipped with an ATX power supply, you should connect the
power on/off button on your computer case to JFP1. This connection enables you to
turn your computer on and off.
JFP1
JFP2
JFP3
PWR_SW
Reset
HDD LED
SNMP
Speaker
PWR_LED & Key Lock
2.8.2 Reset Connector (JFP1)
Many computer cases offer the convenience of a reset button. Connect the wire from
the reset button.
JFP1
JFP2
JFP3
PWR_SW
Reset
HDD LED
SNMP
Speaker
PWR_LED & Key Lock
2.8.3 HDD LED Connector (JFP2)
You can connect an LED to connector JFP2 to indicate when the HDD is active.
JFP1
JFP2
JFP3
17
PWR_SW
Reset
HDD LED
SNMP
Speaker
PWR_LED & Key Lock
PCE-5026 User Manual
Connecting Peripherals
2.8.1 ATX Soft Power Switch (JFP1)
Chapter 2
2.8 Front Panel Connectors (JFP1, JFP2 & JFP3)
2.8.4 External speaker (JFP2)
JFP2 is a 4-pin connector for an external speaker. The PCE-5026 provides an
onboard buzzer as an alternative to an external speaker. To enable the buzzer, set
pins 3 and 4 as closed.
JFP1
JFP2
PWR_SW
Reset
HDD LED
SNMP
Speaker
JFP3
PWR_LED & Key Lock
2.8.5 Power LED and Keyboard Lock (JFP3)
JFP3 is a 5-pin connector for the power LED. Refer to Appendix B for detailed information on the pin assignments. If a PS/2 or ATX power supply is used, the system’s
power LED status will be indicated as shown below:
Table 2.1: PS/2 or ATX Power Supply LED Status
Power mode
LED (PS/2 power)
LED (ATX power)
System On
On
On
System Suspend
Flashes
Flashes
System Off
Off
Off
JFP1
JFP2
PWR_SW
Reset
HDD LED
SNMP
Speaker
JFP3
PWR_LED & Key Lock
2.9 H/W Monitor/Watchdog Timer/Infrared
JIR1+JOBS+JWDT1
JWDT1 JOBS1
J
JIR1
PCE-5026 User Manual
18
Chapter 2
2.9.1 H/W Monitor Alarm (JOBS1)
This 2-pin header is for enabling/disabling H/W monitor alarm function.
Closed: Enables OBS Alarm
Open: Disables OBS Alarm
2.9.2 Watchdog Timer (JWDT1)
Connecting Peripherals
This is for setting action trigger by watchdog timer.
1-2 Pin Close: No Action
2-3 Pin Close: System Reset
2.9.3 Infrared Interface (JIR1)
This is a 5-pin header for an infrared device.
Note!
Please refer to Figure 3.17 to change COM2 device mode in BIOS
menu before using IR device.
2.10 LAN Port (LAN1)
LAN1
LED1 LED2
The PCE-5026 is equipped with one or two high-performance 1000 Mbps Ethernet
LANs. They are supported by all major network operating systems. The RJ-45 jacks
on the rear plate provide convenient connectivity.
Table 2.2: LAN LED Indicators
LAN Mode
1000Mbps Link On
LED1
LED2
Green On
On
1000Mbps Active
Green on
Flash
1000Mbps Link Off
Off
Off
100Mbps Link On
Orange On
On
100Mbps Active
Orange On
Flash
19
PCE-5026 User Manual
Table 2.2: LAN LED Indicators
100Mbps Link Off
Off
Off
10Mbps Link On
Off
On
10Mbps Active
Off
Flash
10Mbps Link Off
Off
Off
2.11 High Definition Audio Module Interface
(HDAUD1)
HDAUD1
This HDAUD1 pin header is the connection interface to Advantech's 7.1 channel high
definition audio module.
Note!
Advantech 7.1 channel high-definition audio module: PCA-AUDIOHDA1E.
PCE-5026 User Manual
20
Chapter 2
Connect CDIN1 with the CD/DVD drive's
CD-in connector with the audio line included
in the CD/DVD drive accessory
i
Connect HDAUD1
to the HDAUD1
pinheader on the
CPU card with the
HD audio cable
(PN:1701120251)
Figure 2.1 Jumper and connector locations of PCA-AUDIO-HDA1E
Note!
Please remove the yellow jumper cap on the CPU card's HDAUD1 pinheader before connecting the HD audio cable to it.
21
PCE-5026 User Manual
Connecting Peripherals
Connect CN1 with
the power supply's
4-pin power
connector
2.12 GPIO Header (GPIO1)
GPIO1
Provides 10-Pin pin header for 8-bit Digital I/O usage. Refer to Appendix B for
detailed information on the pin assignments and programming guide in Appendix C.
2.13 Case Open Connector (JCASE1)
JCASE1
The 2-pin case open connector is for chassis with a case open sensor. When the
case is open, the buzzer on motherboard will beep.
PCE-5026 User Manual
22
Chapter 2
2.14 Front Panel LAN Indicator Connector
(LANLED1)
Table 2.3: LAN LED Indicators
LED1
LED2
1000Mbps Link On
Green On
On
1000Mbps Active
Green on
Flash
1000Mbps Link Off
Off
Off
100Mbps Link On
Orange On
On
100Mbps Active
Orange On
Flash
100Mbps Link Off
Off
Off
10Mbps Link On
Off
On
10Mbps Active
Off
Flash
10Mbps Link Off
Off
Off
LANLED1
23
PCE-5026 User Manual
Connecting Peripherals
LAN Mode
2.15 Serial ATA Interface (SATA1~SATA4)
SATA1~4
The PCE-5026 features high performance serial ATA interface (4* 300MB/s) which
eases cabling to hard drivers or CD/DVD drivers with long cables.
Note!
We recommend plugging in CD/DVD drives on SATA3 and 4.
When you install Linux OS, we recommend you to set AHCI mode in
BIOS setting, otherwise the system may not recognize hard drives
(using IDE mode) during Linux OS installation.
2.16 LPC Extension Interface (LPC1)
LPC1
LPC1 is a 14-pin female pinheader for adopting for adopting Advantech LPC module.
PCE-5026 User Manual
24
Chapter
3
AMI BIOS Setup
3
3.1 Introduction
AMI BIOS has been integrated into motherboards for over a decade. In the past, people often referred to the AMI BIOS setup menu as BIOS, BIOS setup or CMOS setup.
With the AMI BIOS Setup program, you can modify BIOS settings and control the
special features of your computer. The Setup program uses a number of menus for
making changes and turning the special features on or off. This chapter describes the
basic navigation of the PCE-5026 setup screens.
Figure 3.1 Setup Program Initial Screen
PCE-5026 User Manual
26
Turn on the computer and activate BIOS as well. The setup program is triggered by
pressing “DEL” or “F2” key.
Note!
If the message disappears before you press the “DEL” or “F2” key,
please restart the computer and try it again.
When you first enter the BIOS Setup Utility, you will enter the Main setup screen. You
can always return to the Main setup screen by selecting the Main tab. There are two
Main Setup options. They are described in this section. The Main BIOS Setup screen
is shown below.
Figure 3.2 Main Setup Screen
The Main BIOS setup screen has two main frames. The left frame displays all the
options that can be configured. Grayed-out options cannot be configured; options in
blue can. The right frame displays the key legend.
Above the key legend is an area reserved for a text message. When an option is
selected in the left frame, it is highlighted in white. Often a text message will accompany it.
System Time / System Date
Use this option to change the system time and date. Highlight System Time or System Date using the keys. Enter new values through the keyboard. Press the
key or the keys to move between fields. The date must be entered in
MM/DD/YY format. The time must be entered in HH:MM:SS format.
27
PCE-5026 User Manual
AMI BIOS Setup
3.2.1 Main Setup
Chapter 3
3.2 Entering Setup
3.2.2 Advanced BIOS Features Setup
Select the Advanced tab from the PCE-5026 setup screen to enter the Advanced
BIOS Setup screen. You can select any of the items in the left frame of the screen,
such as CPU Configuration, to go to the sub menu for that item. You can display an
Advanced BIOS Setup option by highlighting it using the keys. All Advanced
BIOS Setup options are described in this section. The Advanced BIOS Setup screen
is shown below, and the sub menus are described on the following pages.
Figure 3.3 Advanced BIOS Features Setup Screen
PCE-5026 User Manual
28
Chapter 3
3.2.2.1 Advantech BIOS Update V1.3
AMI BIOS Setup
Figure 3.4 Advantech BIOS Update V1.3
You can update BIOS via USB storage device in FAT32 format.
Note!
BIOS file name must be UPDATE.BIN.
29
PCE-5026 User Manual
3.2.2.2 PCI Subsystem Settings
Figure 3.5 PCI Subsystem Settings
PCI 64-bit Resources Handing
Above 4G Decoding
Enable/Disable 64-bit capable devices to be decoded above 4G address space
(only if system supports 64-bit PCI decoding).
PCI Common Settings
PCI Latency Timer
Value to be programmed into PCI Latency Timer Register.
VGA Palette Snoop
Enables/Disables VGA palette registers snooping.
PCE-5026 User Manual
30
Chapter 3
AMI BIOS Setup
Figure 3.6 PCI Express Settings
Link Training Retry
Defines number of retry attempts software will take to retrain the link if previous
training attempt was unsuccessful.
Link Training Timeout
Defines number of micro-seconds software will wait before polling “Link Training” bit in link status register. Value range from 10 to 1000 uS.
31
PCE-5026 User Manual
3.2.2.3 ACPI Settings
Figure 3.7 ACPI Settings
Power Type
Choose the item that corresponds with your power supply type, ATX or AT.
Enable ACPI AUTO configuration
Enable or disable ACPI auto configuration
Enable Hibernation
Enable or disable Hibernate (OS/S4 Sleep State). This option may not be effective with some OSs.
Lock Legacy Resources
Enable or Disable Lock Legacy Resources.
PowerOn by Modem
Enable or Disable Power On by Modem
PCE-5026 User Manual
32
Chapter 3
3.2.2.4 Trust Computing
AMI BIOS Setup
Figure 3.8 Trust Computing
Security Device Support
Enable or disable BIOS support for security device. You can purchase Advantech’s TPM (Trust Platform Module), PCA-TPM-00A1E, for your security device.
33
PCE-5026 User Manual
3.2.2.5 S5 RTC Wake Setting
Figure 3.9 S5 RTC Configuration
Wake System with Fixed Time
Enable or disable system wake on alarm event, When enabled, system will
wake on the hr:min:sec specified.
3.2.2.6 CPU Configuration
Figure 3.10 CPU Configuration
PCE-5026 User Manual
34
3.2.2.7 SATA Configuration
Figure 3.11 SATA Configuration
35
PCE-5026 User Manual
AMI BIOS Setup
Active Processor Core
Use this to select how many processor cores you want to activate when you are
using a dual or quad core processor.
Limit CPUID Maximum
Setting this item to [Enable] allows legacy operating systems to boot even without support for CPUs with extended CPUID functions.
Execute Disable Bit
This item specifies the Execute Disable Bit Feature. The settings are Enabled
and Disabled. The Optimal and Fail-Safe default setting is Enabled. If Disabled
is selected, the BIOS forces the XD feature flag to always return to 0.
Intel Virtualization Technology
This feature is used to enable or disable the Intel Virtualization Technology (IVT)
extension. It allows multiple operating systems to run simultaneously on the
same system. It does this by creating virtual machines, each running its own x86
operating system.
Hardware Prefetcher
Hardware Prefetcher is a technique that fetches instructions and/or data from
memory into the CPU cache memory well before the CPU needs it, so that it can
improve the load-to-use latency. You may choose to enable or disable it.
Adjacent Cache Line Prefetch
The Adjacent Cache-Line Prefetch mechanism, like automatic hardware
prefetch, operates without programmer intervention. When enabled through the
BIOS, two 64-byte cache lines are fetched into a 128-byte sector, regardless of
whether the additional cache line has been requested or not. You may choose to
enable or disable it.
Chapter 3
SATA Controller(s)
Enable or disable SATA Device
SATA Mode
This can be configured as IDE and AHCI.
Note!
Some Operating systems request to install under AHCI mode. Please
consult local OS agent for detailed information. For example, Fedora 14/
15/16 should be installed under AHCI mode.
3.2.2.8 Intel Trusted Execution Technology Configuration
Figure 3.12 Intel Trusted Execution Technology Configuration
Intel Trusted Execution Technology Configuration
This enables or disables Intel® Trusted Execution Technology.
Note!
Hardware platform should support Trust Platform Module (TPM1.2) to
enable Intel Trusted Execution Technology.
Advantech TPM module P/N: PCA-TPM-00A1E
PCE-5026 User Manual
36
Chapter 3
3.2.2.9 USB Configuration
AMI BIOS Setup
Figure 3.13 USB Configuration
Legacy USB Support
This is for supporting USB devices under legacy OSs such as DOS. When
choosing “AUTO,” the system will automatically detect if any USB device is
plugged into the computer and enable USB legacy mode when a USB device is
plugged and disable USB legacy mode when no USB device is plugged.
EHCI Hand-off
This is a workaround for OSs without EHCI hand-off support. The EHCI ownership change should be claimed by EHCI driver.
USB Transfer Time-out
Allows you to select the USB transfer time-out value. [1, 5,10, 20 sec]
Device Reset Time-out
Allows you to select the USB device reset time-out value. [1, 5,10, 20 sec]
Device Power-up Delay
This item appears only when you set the Device power-up delay item to [manual].
37
PCE-5026 User Manual
3.2.2.10 Smart Settings
Figure 3.14 Smart Settings
Smart Self test
Run SMART Self Test on all HDDs during POST.
3.2.2.11 Super I/O Configuration
Figure 3.15 Super I/O Configuration
PCE-5026 User Manual
38
Chapter 3
AMI BIOS Setup
Figure 3.16 Serial Port 1 Configuration
Figure 3.17 Serial Port 2 Configuration
39
PCE-5026 User Manual
Figure 3.18 Parallel Configuration
Serial Port 1 -2 Configuration
“Enable” or “Disable” Serial Port
Note!
Only serial port 2 can be configured to IrDA or ASKIR mode via BIOS
setting menu.
Parallel Port Configuration
“Enable” or “Disable” Parallel Port
PCE-5026 User Manual
40
Chapter 3
3.2.2.12 H/W Monitor
AMI BIOS Setup
Figure 3.19 PC Health Status
Smart Fan Mode Configuration
Enable or disable Smart fan
Case Open Warning
Enable/Disable the Chassis Intrusion monitoring function. When enabled and
the case is opened, the speaker beeps.
CPU Warning Temperature
Use this to set the CPU warning temperature threshold. When the system
reaches the warning temperature, the speaker will beep.
ACPI Shutdown Temperature
Use this to set the ACPI shutdown temperature threshold. When the system
reaches the shutdown temperature, it will be automatically shut down by ACPI
OS to protect the system from overheating damage.
41
PCE-5026 User Manual
3.2.2.13 CPU PPM Configuration
Figure 3.20 CPU PPM Configuration
EIST
Enable/Disable Intel Speedstep
CPU C3 Report
Enable/Disable CPU C3 (ACPI C2) report to OS.
CPU C6 Report
Enable/Disable CPU C6 (ACPI C2) report to OS.
CPU C7 Report
Enable/Disable CPU C7 (ACPI C2) report to OS.
ACPI T State
Enable/Disable ACPI T state support
PCE-5026 User Manual
42
Chapter 3
3.2.3 Chipset
AMI BIOS Setup
Figure 3.21 Chipset
3.2.3.1 PCH-I/O Configuration
Figure 3.22 PCH I/O Configuration
LAN1 Controller
Enable or Disable LAN1 Controller.
43
PCE-5026 User Manual
LAN 1 Option-ROM
Enable or Disable LAN 1 boot option for legacy network devices.
Wake on LAN1 from S5
Enable or Disable LAN1 to wake the system. (The wake on LAN cannot be disabled if ME is on at Sx state).
High precision Timer
Enable or Disable High Precision Event Timer.
SLP_S4 Assertion Width
Select a minimum assertion width of the SLP_S4# signal.
Restore AC Power Loss
Power Off, power On or Last State to restore AC power loss
3.2.3.2 PCI Express Configuration
Figure 3.23 PCI Express Configuration
Subtractive Decode
Enable or disable PCI Express Subtractive Decode.
PCI Express Configuration
PCI Express Root Port 1 to 8 Setting.
PCE-5026 User Manual
44
Chapter 3
3.2.3.3 USB Configuration
AMI BIOS Setup
Figure 3.24 USB Configuration
EHCI1
Control the USB EHCI(USB2.0) functions. One EHCI controller must always be
enabled.
EHCI2
Control the USB EHCI(USB2.0) functions. One EHCI controller must always be
enabled.
USB Ports Per-port Disable Control
Control each of the USB ports disabling.
45
PCE-5026 User Manual
3.2.3.4 PCH Azalia Configuration
Figure 3.25 PCH Azalia Configuration
Azalia
Control detection of the Azalia device.
Disable=Azalia will be disabled
Enable=Azalia will be enabled
Auto=Azalia will be enabled if present, disabled otherwise.
PCE-5026 User Manual
46
Chapter 3
3.2.3.5 System Agent (SA) Configuration
AMI BIOS Setup
Figure 3.26 System Agent (SA) Configuration
VT-d
Check to enable VT-d function on MCH
47
PCE-5026 User Manual
3.2.3.6 Graphics Configuration
Figure 3.27 Graphics Configuration
Primary Display
Select which of IGFX/PEG/PCI Graphics device should be Primary display or
select SG for switchable Gfx.
Internal Graphics
Keep IGD enabled based on the setup options.
GTT Size
Select the GTT size.
Aperture Size
Select the aperture size.
DVMT Pre-Allocated
Select DVMT5.0 Pre-allocated (fixed) graphics memory size, up to 1024 M,
used by the internal graphics device.
DVMT Total Gfx Mem
Select 128 M, 256 M or MAX DVMT5.0 total graphics memory size used by the
internal graphics device.
Gfx Low Power Mode
This option is applicable for SFF only.
Primary IGFX Display
Select the video device which will be activated during POST. This has no effect
if external graphics present. Secondary boot display selection will appear based
on your selection. VGA modes will be supported only on primary display. Note:
DOS mode only supports either VGA or DVI single output.
PCE-5026 User Manual
48
Chapter 3
3.2.3.7 NB PCIe Configuration
AMI BIOS Setup
Figure 3.28 NB PCIe Configuration
PEG0-Gen X
Configure auto, Gne1, Gen2, or Gen 3.
PEG0 ASPM
Control ASPM support for the PEG: Device 1 Function 0. This has no effect if
PEG is not the currently active device.
Enable PEG
Enable/Disable/Auto the PEG.
De-emphasis Control
Configure the De-emphasis control on PEG
49
PCE-5026 User Manual
3.2.3.8 Memory Configuration
Overview of detailed memory information.
Figure 3.29 Memory Information
3.2.4 Boot
Figure 3.30 Boot
PCE-5026 User Manual
50
3.2.5 Security
Figure 3.31 Security
Select Security Setup from the PCE-5026 Setup main BIOS setup menu. All Security
Setup options, such as password protection and virus protection are described in this
section. To access the sub menu for the following items, select the item and press
51
PCE-5026 User Manual
AMI BIOS Setup
Setup Prompt timeout
Number of seconds to wait for setup activation key.
Bootup NumLock State
Select the keyboard Numlock state.
Quiet Boot
Enable/Disable Quiet Boot option.
GateA20 Active
Upon request-GA20 can be disabled using BIOS services.
Always-do not allow disabling GA20; this option is useful when any RT code is
executed above 1 MB.
Option Rom Messages
Set display mode for option ROM.
INT19 Trap Response
Bios reaction on INT19 trapping via ROM option:
IMMEDATE-execute the trap right away
POSTPONED-execute the trap during legacy boot.
Boot Option Priorities
you can see the information of boot priority option of devices.
Hard Drive BBS Priorities
Set the order of the legacy devices in this group.
Chapter 3
3.2.6 Save & Exit
Figure 3.32 Save & Exit
Save changes and exit*
When you have completed system configuration, select this option to save your
changes, exit BIOS setup and boot into the OS so the new system configuration
parameters can take effect.
Discard changes and exit
Select this option to quit Setup without making any permanent changes to the system
configuration.
Save changes and Reset
When you have completed system configuration, select this option to save your
changes, exit BIOS setup and reboot into the computer so the new system configuration parameters can take effect.
Discard changes and Reset
Select this option to quit Setup and reset computer without making any permanent
changes to the system
configuration.
Save Changes
Select this option to save your changes.
Discard Changes
Select this option to discard your changes.
PCE-5026 User Manual
52
Chapter 3
Restore Defaults
Select this option to restore BIOS configuration to original.
Save as User Defaults
Select this option to save user configuration.
Restore User Defaults
Select this option to restore BIOS to user configuration.
*When you do some critical changes, the system will still reboot even you choose
“Save changes and exit.”
53
PCE-5026 User Manual
AMI BIOS Setup
Launch EFI Shell from file system device
This option allows you to attempt to launch the EFI Shell application (shellx64.efi)
from one of the available file system devices.
PCE-5026 User Manual
54
Chapter
4
Chipset Software
Installation Utility
4
4.1 Before You Begin
To facilitate the installation of the enhanced display drivers and utility software, read
the instructions in this chapter carefully. The drivers for the PCE-5026 are located on
the software installation CD. The driver in the folder of the driver CD will guide and
link you to the utilities and drivers under a Windows system. Updates are provided
via Service Packs from Microsoft®.
Note!
The files on the software installation CD are compressed. Do not
attempt to install the drivers by copying the files manually. You must use
the supplied SETUP program to install the drivers.
Before you begin, it is important to note that most display drivers need to have the
relevant software application already installed in the system prior to installing the
enhanced display drivers. In addition, many of the installation procedures assume
that you are familiar with both the relevant software applications and operating system commands. Review the relevant operating system commands and the pertinent
sections of your application software’s user manual before performing the installation.
4.2 Introduction
The Intel® Chipset Software Installation (CSI) utility installs the Windows INF files
that outline to the operating system how the chipset components will be configured.
This is needed for the proper functioning of the following features:
Core PCI PnP services
Serial ATA interface support
USB 1.1/2.0 support
Identification of Intel® chipset components in the Device Manager
Integrates superior video features. These include filtered sealing of 720 pixel
DVD content, and MPEG-2 motion compensation for software DVD
PCE-5026 User Manual
56
Insert the driver CD into your system’s CD-ROM drive. You can see the driver
folder items. Navigate to the “01-Chipset” folder and click “setup.exe” to complete the installation of the driver.
Note!
57
PCE-5026 User Manual
Chipset Software Installation Utility
Wrong driver installation may cause unexpected system instability.
The drivers on this CD support both Windows XP 32-bit /64-bit and Windows 7 32-bit/64-bit.
Chapter 4
4.3 Windows® XP / Windows® 7 Driver Setup
PCE-5026 User Manual
58
Chapter
5
5
Integrated Graphic
Device Setup
5.1 Introduction
The Intel® LGA1155 CPUs have integrated graphics controllers. You need to install
the VGA driver to enable this function, which includes the following features:
Optimized integrated graphic solution: Intel Graphics Flexible Display Interface supports versatile display options and 32-bit 3D graphics engine. Dual
independent display, enhanced display modes for widescreen flat panels for
extend, twin, and clone dual display mode, and optimized 3D support deliver an
intensive and realistic visual experience.
5.2 Windows XP/Windows 7 Driver Setup
Note!
Before installing this driver, make sure the INF driver has been installed
on your system. See Chapter 4 for information on installing the INF
driver.
Insert the Advantech driver DVD into your system and navigate to folder named
“02_VGA” to choose proper operating system, then install driver by clicking
“setup.exe” or “install.exe.”
Note!
Wrong driver installation may cause unexpected system instability.
Intel VGA driver for Windows XP does not support Microsoft Direct X 10
and 11.
Only Intel Generation 3 CPUs (Ivybridge) support Microsoft Direct X11
in Windows 7.
PCE-5026 User Manual
60
Chapter
6
6
LAN Configuration
6.1 Introduction
PCE-5026 features single Gigabit Ethernet via dedicated Intel 82579V which offers
500 Mbps bandwidth, eliminating the bottleneck of network data flow and incorporating Gigabit Ethernet at 1000 Mbps.
6.2 Features
10, 100, 1000 BASE-T IEEE 802.3 specification conformance.
Jumbo Frames support (up to 9 kB)
Wake on LAN (WoL) support
6.3 Installation
Note!
Before installing the LAN drivers, make sure the Intel CSI utility has
been installed on your system. See Chapter 4 for information on installing the CSI utility.
The PCE-5026's Intel 82579V (LAN1) Gigabit integrated controllers support all major
network operating systems. However, the installation procedure varies from system
to system. Please find and use the section that provides the driver setup procedure
for the operating system you are using.
6.4 Win XP /Win 7 Driver Setup (LAN)
Insert the driver CD into your system’s CD-ROM drive. Navigate to the “03-LAN”
folder and click “Autorun.exe” to complete the installation of the driver.
Note!
Wrong driver installation may cause unexpected system instability.
PCE-5026 User Manual
62
Chapter
7
Intel ME
7
7.1 Introduction
The Intel® ME software components that need to be installed depend on the system's specific hardware and firmware features. The installer detects the system's
capabilities and installs the relevant drivers and applications.
7.2 Installation
Insert the driver CD into your system’s CD-ROM drive. Navigate to the “04-Intel ME”
folder and click “setup.exe” to complete the installation of the driver.
Note!
If the Intel® Management Engine (Intel® ME) driver has not been successfully installed, you may see an error on a “PCI Simple Communications Controller” in Device Manager.
PCE-5026 User Manual
64
Appendix
A
A
Programming the
Watchdog Timer
A.1 Introduction
The PCE-5026’s watchdog timer can be used to monitor system software operation
and take corrective action if the software fails to function within the programmed
period. This section describes the operation of the watchdog timer and how to program it.
A.1.1 Watchdog Timer Overview
The watchdog timer is built in to the NCT6776F super I/O controller. It provides the
following user programmable functions:
Can be enabled and disabled by user’s program
Timer can be set from 1 to 255 seconds or 1 to 255 minutes
Generates reset signal if the software fails to reset the timer before time-out
A.1.2 Programming the Watchdog Timer
The I/O port address of the watchdog timer is 2E (hex) and 2F (hex). 2E (hex) is the
address port. 2F (hex) is the data port. You must first write an address value into
address port 2E (hex), then write/read data to/from the assigned register through
data port 2F (hex).
PCE-5026 User Manual
66
Appendix A Programming the Watchdog Timer
Unlock
NCT6776F
Select register of
watchdog timer
Enable the function of
the watchdog timer
Use the function of
the watchdog timer
Lock
NCT6776F
Table A.1: Watchdog Timer Registers
Address of
register (2E)
Attribute
Read/Write
Value (2F)& description
87 (hex)
-----
Write this address to I/O address port 2E (hex) twice to
unlock the NCT6776F
07 (hex)
write
Write 08 (hex) to select register of watchdog timer.
write
Write 01 (hex) to enable the function of the watchdog
timer. Disabled is set as default.
write
Set seconds or minutes as units for the timer. Write 0 to
bit 3: set second as counting unit. [default]. Write 1 to bit
3: set minutes as counting unit
Write 1 to bit 4: Watchdog timer count mode is 1000
times faster.
If bit 3 is 0, the count mode is 1/1000 seconds mode. If
bit 3 is 1, the count mode is 1/1000 minutes mode.
30 (hex)
F5 (hex)
67
PCE-5026 User Manual
write
0: stop timer [default]
01~FF (hex): The amount of the count, in seconds or
minutes, depends on the value set in register F5 (hex).
This number decides how long the watchdog timer waits
for strobe before generating an interrupt or reset signal.
Writing a new value to this register can reset the timer to
count with the new value.
F7 (hex)
read/write
Bit 6: Write 1 to enable keyboard to reset the timer, 0 to
disable.[default]
Bit 5: Write 1 to generate a timeout signal immediately
and automatically return to 0. [default=0]
Bit 4: Read status of watchdog timer, 1 means timer is
“timeout”.
AA (hex)
-----
Write this address to I/O port 2E (hex) to lock the
NCT6776F.
F6 (hex)
A.1.3 Example Program
1. Enable watchdog timer and set 10 sec. as timeout interval
;----------------------------------------------------------Mov dx,2eh
; Unlock NCT6776F
Mov al,87h
Out dx,al
Out dx,al
;----------------------------------------------------------Mov al,07h
; Select registers of watchdog timer
Out
dx,al
Inc
dx
Mov
al,08h
Out
dx,al
;----------------------------------------------------------Dec dx
; Enable the function of watchdog timer
Mov
al,30h
Out
dx,al
Inc
dx
In
al,dx
Or
al,03h
Out
dx,al
;----------------------------------------------------------Dec dx
; Set second as counting unit
Mov
al,0f5h
Out
dx,al
Inc
dx
In
al,dx
And al,not 08h
Out
dx,al
;----------------------------------------------------------Dec dx
; Set timeout interval as 10 seconds and
start counting
PCE-5026 User Manual
68
2. Enable watchdog timer and set 5 minutes as timeout interval
;----------------------------------------------------------Mov dx,2eh
; Unlock NCT6776F
Mov al,87h
Out dx,al
Out dx,al
;----------------------------------------------------------Mov al,07h
; Select registers of watchdog timer
Out
dx,al
Inc
dx
In
al,dx
Or
al,08h
Out
dx,al
;----------------------------------------------------------Dec dx
; Enable the function of watchdog timer
Mov
al,30h
Out
dx,al
Inc
dx
Mov
al,03h
Out
dx,al
;----------------------------------------------------------Dec dx
; Set minute as counting unit
Mov
al,0f5h
Out
dx,al
Inc
dx
In
al,dx
Or
al,08h
Out
dx,al
;----------------------------------------------------------Dec dx
; Set timeout interval as 5 minutes and
start counting
Mov
al,0f6h
Out
dx,al
Inc
dx
Mov
al,5
; 5 minutes
Out
dx,al
69
PCE-5026 User Manual
Appendix A Programming the Watchdog Timer
Mov
al,0f6h
Out
dx,al
Inc
dx
Mov
al,10
; 10 seconds
Out
dx,al
;----------------------------------------------------------Dec dx
; Lock NCT6776F
Mov
al,0aah
Out
dx,al
;----------------------------------------------------------Dec dx
; Lock NCT6776F
Mov
al,0aah
Out
dx,al
3. Enable watchdog timer to be reset by mouse
;----------------------------------------------------------Mov dx,2eh
; Unlock NCT6776F
Mov al,87h
Out dx,al
Out dx,al
;----------------------------------------------------------Mov al,07h
; Select registers of watchdog timer
Out
dx,al
Inc
dx
Mov
al,08h
Out
dx,al
;----------------------------------------------------------Dec dx
; Enable the function of watchdog timer
Mov
al,30h
Out
dx,al
Inc
dx
In
al,dx
Or
al,03h
Out
dx,al
;----------------------------------------------------------Dec dx
; Enable watchdog timer to be reset by
mouse
Mov
al,0f7h
Out
dx,al
Inc
dx
In
al,dx
Or
al,80h
Out
dx,al
;----------------------------------------------------------Dec dx
; Lock NCT6776F
Mov
al,0aah
Out
dx,al
4. Enable watchdog timer to be reset by keyboard
;----------------------------------------------------------Mov dx,2eh
; Unlock NCT6776F
Mov al,87h
Out dx,al
Out dx,al
;----------------------------------------------------------PCE-5026 User Manual
70
5. Generate a time-out signal without timer counting
;----------------------------------------------------------Mov dx,2eh
; Unlock NCT6776F
Mov al,87h
Out dx,al
Out dx,al
;----------------------------------------------------------Mov al,07h
; Select registers of watchdog timer
Out
dx,al
Inc
dx
Mov
al,08h
Out
dx,al
;----------------------------------------------------------Dec dx
; Enable the function of watchdog timer
Mov
al,30h
Out
dx,al
Inc
dx
Mov
al,03h
Out
dx,al
;----------------------------------------------------------71
PCE-5026 User Manual
Appendix A Programming the Watchdog Timer
Mov al,07h
; Select registers of watchdog timer
Out
dx,al
Inc
dx
Mov
al,08h
Out
dx,al
;----------------------------------------------------------Dec dx
; Enable the function of watchdog timer
Mov
al,30h
Out
dx,al
Inc
dx
Mov
al,03h
Out
dx,al
;----------------------------------------------------------Dec dx
; Enables watchdog timer to be strobe
reset by keyboard
Mov
al,0f7h
Out
dx,al
Inc
dx
In
al,dx
Or
al,40h
Out
dx,al
;----------------------------------------------------------Dec dx
; Lock NCT6776F
Mov
al,0aah
Out
dx,al
Dec dx
; Generate a time-out signal
Mov
al,0f7h
Out
dx,al
;Write 1 to bit 5 of F7 register
Inc
dx
In
al,dx
Or
al,20h
Out
dx,al
;----------------------------------------------------------Dec dx
; Lock NCT6776F
Mov
al,0aah
Out
dx,al
PCE-5026 User Manual
72
Appendix
B
B
I/O Pin Assignments
B.1 Parallel Port Connector (LPT1)
25 23
3 1
26 24
4 2
Table B.1: Parallel port Connector (LPT1)
Pin
Signal
Pin
Signal
1
STROBE*
2
AUTOFD*
3
D0
4
ERR
5
D1
6
INIT*
7
D2
8
SLCTINI*
9
D3
10
GND
11
D4
12
GND
13
D5
14
GND
15
D6
16
GND
17
D7
18
GND
19
ACK*
20
GND
21
BUSY
22
GND
23
PE
24
GND
25
SLCT
26
No pin
* low active
B.2 VGA Connector (VGA1)
5
1
10
6
15
11
Table B.2: VGA Connector (VGA1)
Pin
Signal
Pin
Signal
1
2
RED
9
VCC
GREEN
10
GND
3
BLUE
11
N/C
4
N/C
12
SDT
5
GND
13
H-SYNC
6
GND
14
V-SYNC
7
GND
15
SCK
8
GND
PCE-5026 User Manual
74
Appendix B I/O Pin Assignments
B.3 RS-232 Seral Port (COMD1)
Table B.3: COM Connector (COMD1)
Pin
Signal
1
DCD
2
SIN
3
SOUT
4
DTR
5
GND
6
DSR
7
RTS
8
CTS
9
RI
B.4 RS-232 Serial Port (COM2)
Table B.4: RS-232 Serial Port (COM2)
Pin
Signal
1
DCD
2
DSR
3
SIN
4
RTS
5
SOUT
6
CTS
7
DTR
8
RI
9
GND
75
PCE-5026 User Manual
B.5 USB 2.0 Header (USB12 & USB34)
Table B.5: USB Header (USB12 & USB34)
Pin
Signal
Pin
Signal
1
USB1_VCC5
6
USB2_D+
2
USB2_VCC5
7
GND
3
USB1_D-
8
GND
4
USB2_D-
9
No pin
5
USB1_D+
10
N/A
B.6 PS/2 Keyboard/Mouse Connector (KBMS1)
6
5
4
3
2
1
Table B.6: PS/2 Keyboard/Mouse Connector (KBMS1)
Pin
Signal
1
KB DATA
2
MS DATA
3
GND
4
VCC
5
KB CLOCK
6
MS CLOCK
PCE-5026 User Manual
76
6
5
4
3
2
1
Table B.7: External Keyboard Connector (KBMS2)
Pin
Signal
1
KBCLK
2
KBDAT
3
MSDAT
4
GND
5
MSVCC
6
MSCLK
B.8 CPU Fan Power Connector (CPUFAN1)
1
2
3
4
Table B.8: CPU Fan Power Connector (CPUFAN1)
Pin
Signal
1
GND
2
+12V
3
Detect
4
NC
B.9 Power LED and Keyboard Lock Connector
(JFP3 / PWR_LED & KEY LOCK)
Table B.9: Power LED and Keyboard Lock Connector (JFP3 / PWR_LED
& KEY LOCK)
Pin
Signal
1
LED power (+3.3 V)
2
NC
3
GND
4
KEYLOCK#
5
GND
77
PCE-5026 User Manual
Appendix B I/O Pin Assignments
B.7 External Keyboard Connector (KBMS2)
B.10 External Speaker Connector (JFP2 / SPEAKER)
Table B.10: External Speaker Connector (JFP2 / SPEAKER)
Pin
Signal
1
SPK_CN17P1
2
SPK_CN17P2
3
SPK_CN17P3
4
SPK_CN17P4
B.11 Reset Connector (JFP1 / RESET)
Table B.11: Reset Connector (JFP1 / RESET)
Pin
Signal
1
RESET #
2
GND
B.12 HDD LED (JFP2 / HDDLED)
Table B.12: HDD LED (JFP2 / HDDLED)
Pin
Signal
1
HDD LED
2
SATA LED
PCE-5026 User Manual
78
Table B.13: ATX Soft Power Switch (JFP1 / PWR_SW)
Pin
Signal
1
3.3V_SB
2
PWR-BTN
B.14 Hi-definition Audio Link Connector (HDAUD1)
Table B.14: Hi-Definition Audio Link Connector (HDAUD1)
Pin
Signal
Pin
Signal
1
ACZ_VCC
2
GND
3
ACZ_SYNC
4
ACZ_BITCLK
5
ACZ_SDOUT
6
ACZ_SDIN0
7
ACZ_SDIN1
8
ACZ_RST
9
ACZ_12V
10
GND
11
GND
12
N/A
B.15 SM Bus Connector (JFP2 / SNMP)
Table B.15: SM Bus Connector (JFP2 / SNMP)
Pin
Signal
1
SMB_DATA
2
SMB_CLK
79
PCE-5026 User Manual
Appendix B I/O Pin Assignments
B.13 ATX Soft Power Switch (JFP1 / PWR_SW)
B.16 LAN1 LED Connector (LANLED1)
1
3
5
7
9
2
4
6
8
Table B.16: LAN1 LED Connector (LANLED1)
Pin
Signal
1
#LAN1_ACT
2
N/A
3
V33_AUX
4
N/A
5
#LAN1_LINK1000
6
N/A
7
#LAN1_LINK100
8
N/A
9
V33_AUX
B.17 GPIO Header (GPIO1)
1
2
3
4
5
6
7
8
9
10
Table B.17: GPIO Header (GPIO1)
Pin
Signal
1
SIO_GPIO0
2
SIO_GPIO4
3
SIO_GPIO1
4
SIO_GPIO5
5
SIO_GPIO2
6
SIO_GPIO6
7
SIO_GPIO3
8
SIO_GPIO7
9
VCC_GPIO
10
GND
PCE-5026 User Manual
80
Table B.18: Fixed I/O Ranges Decoded by PCH
I/O Address
Read Target
Write Target
Internal Unit
00h-08h
DMA Controller
DMA Controller
DMA
09h-0Eh
RESERVED
DMA Controller
DMA
0Fh
DMA Controller
DMA Controller
DMA
10h-18h
DMA Controller
DMA Controller
DMA
19h-1Eh
RESERVED
DMA Controller
DMA
1Fh
DMA Controller
DMA Controller
DMA
20h-21h
Interrupt Controller
Interrupt Controller
Interrupt
24h-25h
Interrupt Controller
Interrupt Controller
Interrupt
28h-29h
Interrupt Controller
Interrupt Controller
Interrupt
2Ch-2Dh
Interrupt Controller
Interrupt Controller
Interrupt
2Eh-2Fh
LPC SIO
LPC SIO
Forwarded to LPC
30h-31h
Interrupt Controller
Interrupt Controller
Interrupt
34h-35h
Interrupt Controller
Interrupt Controller
Interrupt
38h-39h
Interrupt Controller
Interrupt Controller
Interrupt
3Ch-3Dh
Interrupt Controller
Interrupt Controller
Interrupt
40h-42h
Timer/Counter
Timer/Counter
PIT (8254)
43h
RESERVED
Timer/Counter
PIT
4Eh-4Fh
LPC SIO
LPC SIO
Forwarded to LPC
50h-52h
Timer/Counter
Timer/Counter
PIT
53h
RESERVED
Timer/Counter
PIT
60h
Microcontroller
Microcontroller
Forwarded to LPC
61h
NMI Controller
NMI Controller
Processor I/F
62h
Microcontroller
Microcontroller
Forwarded to LPC
64h
Microcontroller
Microcontroller
Forwarded to LPC
66h
Microcontroller
Microcontroller
Forwarded to LPC
70h
RESERVED
NMI and RTC ControlRTC
ler
71h
RTC Controller
RTC Controller
72h
RTC Controller
NMI and RTC ControlRTC
ler
73h
RTC Controller
RTC Controller
74h
RTC Controller
NMI and RTC ControlRTC
ler
75h
RTC Controller
RTC Controller
76h
RTC Controller
NMI and RTC ControlRTC
ler
77h
RTC Controller
RTC Controller
80h
DMA Controller, LPC, DMA Controller, LPC,
DMA
PCI, or PCIe
PCI, or PCIe
81h-83h
DMA Controller
DMA Controller
DMA
84h-86h
DMA Controller
DMA Controller and
LPC, PCI, or PCIe
DMA
87h
DMA Controller
DMA Controller
DMA
81
RTC
RTC
RTC
RTC
PCE-5026 User Manual
Appendix B I/O Pin Assignments
B.18 Fixed I/O Ranges Decoded by Intel PCH
88h
DMA Controller
DMA Controller and
LPC, PCI, or PCIe
DMA
89h-8Bh
DMA Controller
DMA Controller
DMA
8Ch-8Eh
DMA Controller
DMA Controller and
LPC, PCI, or PCIe
DMA
8Fh
DMA Controller
DMA Controller
DMA
90h-91h
DMA Controller
DMA Controller
DMA
92h
Reset Generator
Reset Generator
Processor I/F
93h-9Fh
DMA Controller
DMA Controller
DMA
A0h-A1h
Interrupt Controller
Interrupt Controller
Interrupt
A4h-A5h
Interrupt Controller
Interrupt Controller
Interrupt
A8h-A9h
Interrupt Controller
Interrupt Controller
Interrupt
ACh-Adh
Interrupt Controller
Interrupt Controller
Interrupt
B0h-B1h
Interrupt Controller
Interrupt Controller
Interrupt
B2h-B3h
Power Management
Power Management
Power Management
B4h-B5h
Interrupt Controller
Interrupt Controller
Interrupt
B8h-B9h
Interrupt Controller
Interrupt Controller
Interrupt
BCh-BDh
Interrupt Controller
Interrupt Controller
Interrupt
C0h-D1h
DMA Controller
DMA Controller
DMA
D2h-DDh
RESERVED
DMA Controller
DMA
DEh-DFh
DMA Controller
DMA Controller
DMA
F0h
FERR# / Interrupt
Controller
FERR# / Interrupt
Controller
Processor I/F
170h-177h
SATA Controller, PCI, SATA Controller, PCI,
SATA
or PCIe
or PCIe
1F0h-1F7h
SATA Controller, PCI, SATA Controller, PCI,
SATA
or PCIe
or PCIe
200h-207h
Gameport Low
Gameport Low
Forwarded to LPC
208h-20Fh
Gameport High
Gameport High
Forwarded to LPC
376h
SATA Controller, PCI, SATA Controller, PCI,
SATA
or PCIe
or PCIe
3F6h
SATA Controller, PCI, SATA Controller, PCI,
SATA
or PCIe
or PCIe
4D0h-4D1h
Interrupt Controller
Interrupt Controller
Interrupt
CF9h
Reset Generator
Reset Generator
Processor I/F
PCE-5026 User Manual
82
Table B.19: System I/O Ports
I/O Address(Hex)
Device
290h-29Fh
H/W Monitor
2F8h-2FFh
Communication Port (COM2)
378h-37Fh
ECP Printer Port(LPT1)
3B0h-3BBh
Graphics
3C0h-3DFh
Graphics
3F8h-3FFh
Communication Port (COM1)
400h-47Fh
PMBASE
500h-57Fh
GPIOBASE
600h-67Fh
PCA-COM485 Module I/O used
778h-77Fh
ECP Printer Port(LPT1)
C80h-C9Fh
Communication port (COM3-6) for PCA-COM232 module
CA0h-CBFh
Communication port (COM8-11) for PCA-COM485 module
B.20 Interrupt Assignments
Table B.20: Interrupt Assignments
Interrupt#
Interrupt source
NMI
Parity error detected
IRQ0
System timer
IRQ1
Standard 101/102-key or Microsoft Natural PS/2 keyboard
IRQ2
Interrupt from controller 2 (cascade)
IRQ3
Communication port (COM2)
IRQ4
Communication port (COM1)
IRQ5
Available
IRQ6
Available
IRQ7
LPT1
IRQ8
System COMS/Real-time clock
IRQ9
SCI IRQ
IRQ10
Communication port (COM3-6) for PCA-COM232 module
IRQ11
Communication port (COM8-11) for PCA-COM485 module
IRQ12
PS/2 mouse
IRQ13
Numeric data processor
IRQ14
Available
IRQ15
Available
83
PCE-5026 User Manual
Appendix B I/O Pin Assignments
B.19 System I/O Ports
B.21 1 MB Memory Map
Table B.21: 1 MB Memory Map
Address Range
Device
E8000h - FFFFFh
BIOS
D0000h - E7FFFh
Unused
C0000h - CFFFFh
VGA BIOS
A0000h - BFFFFh
Video Memory
00000h - 9FFFFh
Base memory
B.22 PCI Bus Map
Table B.22: PCI Bus Map
Signal
IDSEL
INT#PIN
GNT
REQ
PCI Slot 1
AD31
INT B, C, D, A
GNT A
REQ A
PCI Slot 2
AD30
INT C, D, A, B
GNT B
REQ B
PCI Slot 3
AD29
INT D, A, B, C
GNT C
REQ C
PCI Slot 4
AD28
INT A, B, C, D
GNT D
REQ D
PCE-5026 User Manual
84
Appendix
C
C
Programming the
GPIO
C.1 Supported GPIO Register
Below are the detailed descriptions of the GPIO addresses and programming sample.
C.2 GPIO Registers
Bank
Offset Description
09h
30h
Write 1 to bit 7 to enable GPIO
E0h
GPIO I/O Register
When set to a '1', respective GPIO port is programmed as an input port.
When set to a '0', respective GPIO port is programmed as an output port.
E1h
GPIO Data Redister
If a port is programmed to be an output port, then
its respective bit can be read/written.
If a port is programmed to be an input port, then its
respective bit can only be read.
E2h
GPIO Inversion Register
When set to a '1', the incoming/outgoing port value
is inverted.
When set to a '0', the incoming/outgoing port value
is the same as in data register.
07h
07h
07h
C.3 GPIO Example Program-1
-----------------------------------------------Enter the extended function mode, interruptible double-write
-----------------------------------------------MOV DX,2EH
MOV AL,87H
OUT DX,AL
OUT DX,AL
-------------------------------------------------------------Configure
logical
device,
configuration
register
CRE0,CRE1,CRE2
-------------------------------------------------------------MOV DX,2EH
MOV AL,09H
OUT DX,AC
DEC DX
MOV AL,30H
OUT DX,AL
INC DX
IN AL,DX
OR AL,10000000B
PCE-5026 User Manual
86
87
PCE-5026 User Manual
Appendix C Programming the GPIO
DEC DX
MOV AL,07H
OUT DX,AL
INC DX
MOV AL,07H ; Select logical device 7
OUT DX,AL ;
DEC DX
MOV AL,E0H
OUT DX,AL
INC DX
MOV AL,00H ; 1:Input 0:output for GPIO respective
OUT DX,AL
DEC DX
MOV AL,E2H ;
OUT DX,AL
INC DX
MOV AL,00H
;Set GPIO is normal not inverter
OUT DX,AL;
DEC DX
MOV AL,E1H
OUT DX,AL
INC DX
MOV AL,??H ; Put the output value into AL
OUT DX,AL
-----------------------------------------Exit extended function mode |
-----------------------------------------MOV DX,2EH
MOV AL,AAH
OUT DX,AL
www.advantech.com
Please verify specifications before quoting. This guide is intended for reference
purposes only.
All product specifications are subject to change without notice.
No part of this publication may be reproduced in any form or by any means,
electronic, photocopying, recording or otherwise, without prior written permission of the publisher.
All brand and product names are trademarks or registered trademarks of their
respective companies.
© Advantech Co., Ltd. 2012
工商网监
湘ICP备2023018690号
