MAAM-010513-TR0500

MAAM-010513 Amplifier, Driver 40.5 - 43.5 GHz Rev. V5 Features       Functional Schematic Gain: 23 dB P1dB: 23 dBm OIP3: 32 dBm Variable Gain with Adjustable Bias Lead-Free 5 mm Laminate Package RoHS* Compliant and 260°C Reflow Compatible Description The MAAM-010513 is a 3-stage driver amplifier with excellent return losses, in a 5 mm laminate package allowing easy assembly. This amplifier product is fully matched to 50 ohms on both the input and output. It can be used as a driver amplifier stage in transmit chains or as an LO buffer amplifier. It is ideally suited for 42 GHz band point-to-point radios. Each device is 100% RF tested to ensure performance compliance. The part is fabricated using an efficient pHEMT process. Pin Configuration1 Ordering Information Part Number Package Pin No. Function Pin No. Function MAAM-010513-000000 Bulk Quantity 1 RFIN 7 RFOUT MAAM-010513-TR0200 200 Piece Reel 2 VG1 8 VD3 MAAM-010513-TR0500 500 Piece Reel 3 VG2 9 VD2 MAAM-010513-001SMB Sample Evaluation Board 4 VG3 10 VD1 5 No Connection 11 No Connection 6 No Connection 12 No Connection Paddle2 Ground 1. MACOM recommends connecting unused package pins to ground. 2. The exposed pad centered on the package bottom must be connected to RF and DC ground.  Restrictions on Hazardous Substances, European Union Directive 2002/95/EC. 1 M/A-COM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice. Visit www.macom.com for additional data sheets and product information. For further information and support please visit: https://www.macom.com/support MAAM-010513 Amplifier, Driver 40.5 - 43.5 GHz Rev. V5 Electrical Specifications: Freq: 40.5 - 43.5 GHz, TA = 25°C, VD = 4 V, ID1 = ID2 = 100 mA, ID3 = 200 mA Parameter Units Min. Typ. Max. Small Signal Gain dB 19 23 27 Input Return Loss dB - 12 - Output Return Loss dB - 15 - Reverse isolation dB - 50 - Output P1dB dBm - 23 - Output IP3 dBm 27 32 - Saturated Output Power dBm 21 25 - mA - 400 500 Quiescent Current 3 3. Adjust Vg between –1.0 and –0.1 V to achieve specified current. Typical 400 mA = 100 (ID1) + 100 (ID2) + 200 (ID3) Absolute Maximum Ratings 4,5,6 Handling Procedures Parameter Absolute Max. Drain Voltage +4.3 V Gate Bias Voltage -1.5V < Vg < 0V Input Power +10 dBm Junction Temperature7 150°C Operating Temperature -40°C to +85°C Storage Temperature -55°C to +150°C Please observe the following precautions to avoid damage: Static Sensitivity Gallium Arsenide Integrated Circuits are sensitive to electrostatic discharge (ESD) and can be damaged by static electricity. Proper ESD control techniques should be used when handling these Human Body Model Class 1B and Machine Model Class A devices. 4. Exceeding any one or combination of these limits may cause permanent damage to this device. 5. MACOM does not recommend sustained operation near these survivability limits. 6. Operating at nominal conditions with TJ ≤ 150°C will ensure MTTF > 1 x 106 hours. 7. Junction Temperature (TJ) = TC + Өjc * (V * I) Typical thermal resistance (Өjc) = 26° C/W. a) For TC = 25°C, TJ = 67°C @ 4 V, 400 mA b) For TC = 85°C, TJ = 127°C @ 4 V, 400 mA 2 M/A-COM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice. Visit www.macom.com for additional data sheets and product information. For further information and support please visit: https://www.macom.com/support MAAM-010513 Amplifier, Driver 40.5 - 43.5 GHz Rev. V5 Typical Performance Curves: VD = 4 V, ID1 = ID2 = 100 mA, ID3 = 200 mA, T A = 25°C Small Signal Gain Input Return Loss 40 0 30 -10 20 -20 +25°C -40°C +85°C 10 0 40.5 41.0 41.5 42.0 42.5 -30 43.0 43.5 -40 40.5 41.0 Frequency (GHz) 41.5 42.0 42.5 43.0 43.5 43.0 43.5 43.0 43.5 Frequency (GHz) Reverse Isolation Output Return Loss 0 -20 -30 -10 -40 -20 -50 -30 -60 -40 40.5 41.0 41.5 42.0 42.5 43.0 43.5 -70 40.5 41.0 Frequency (GHz) 60 34 57 32 54 30 51 28 48 41.5 42.0 42.5 C/I3 (Pout = 6 dBm SCL) 36 41.0 42.0 Frequency (GHz) Output IP3 (Pout = 6 dBm SCL) 26 40.5 41.5 42.5 Frequency (GHz) 43.0 43.5 45 40.5 41.0 41.5 42.0 42.5 Frequency (GHz) 3 M/A-COM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice. Visit www.macom.com for additional data sheets and product information. For further information and support please visit: https://www.macom.com/support MAAM-010513 Amplifier, Driver 40.5 - 43.5 GHz Rev. V5 Typical Performance Curves: VD = 4 V, ID1 = ID2 = 100 mA, ID3 = 200 mA, T A = 25°C Output P1dB Psat 28 30 26 28 24 26 22 24 +25°C -40°C +85°C 20 18 40.5 41.0 +25°C -40°C +85°C 22 41.5 42.0 42.5 Frequency (GHz) 43.0 43.5 20 40.5 41.0 41.5 42.0 42.5 43.0 Frequency (GHz) 4 M/A-COM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice. Visit www.macom.com for additional data sheets and product information. For further information and support please visit: https://www.macom.com/support 43.5 MAAM-010513 Amplifier, Driver 40.5 - 43.5 GHz Rev. V5 App Note [1] Biasing - It is recommended to bias the amplifier with Vd=4.0 V and IdTOTAL=400 mA. It is also recommended to use active biasing to keep the currents constant as the RF power and temperature vary; this gives the most reproducible results. Depending on the supply voltage available and the power dissipation constraints, the bias circuit may be a single transistor or a low power operational amplifier, with a low value resistor in series with the drain supply used to sense the current. The gate of the pHEMT is controlled to maintain correct drain current and thus drain voltage. The typical gate voltage needed to do this is -0.3 V. Typically the gate is protected with Silicon diodes to limit the applied voltage. Also, make sure to sequence the applied voltage to ensure negative gate bias is available before applying the positive drain supply. App Note [2] Bias Arrangement - Each DC pin (Vd and Vg) needs to have DC bypass capacitance (100pF/10nF/1uF) as close to the package as possible. Recommended Board Layout 5 M/A-COM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice. Visit www.macom.com for additional data sheets and product information. For further information and support please visit: https://www.macom.com/support MAAM-010513 Amplifier, Driver 40.5 - 43.5 GHz Rev. V5 Lead-Free 5 x 5 mm Laminate Package† Top View Side View Bottom View Recommended Substrate Footprint † Reference Application Note S2083 for lead-free solder reflow recommendations. Meets JEDEC moisture sensitivity level 3 requirements. 6 M/A-COM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice. Visit www.macom.com for additional data sheets and product information. For further information and support please visit: https://www.macom.com/support MAAM-010513 Amplifier, Driver 40.5 - 43.5 GHz Rev. V5 M/A-COM Technology Solutions Inc. All rights reserved. Information in this document is provided in connection with M/A-COM Technology Solutions Inc ("MACOM") products. These materials are provided by MACOM as a service to its customers and may be used for informational purposes only. Except as provided in MACOM's Terms and Conditions of Sale for such products or in any separate agreement related to this document, MACOM assumes no liability whatsoever. MACOM assumes no responsibility for errors or omissions in these materials. MACOM may make changes to specifications and product descriptions at any time, without notice. MACOM makes no commitment to update the information and shall have no responsibility whatsoever for conflicts or incompatibilities arising from future changes to its specifications and product descriptions. No license, express or implied, by estoppels or otherwise, to any intellectual property rights is granted by this document. THESE MATERIALS ARE PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, RELATING TO SALE AND/OR USE OF MACOM PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, CONSEQUENTIAL OR INCIDENTAL DAMAGES, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. MACOM FURTHER DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. MACOM SHALL NOT BE LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS, WHICH MAY RESULT FROM THE USE OF THESE MATERIALS. MACOM products are not intended for use in medical, lifesaving or life sustaining applications. MACOM customers using or selling MACOM products for use in such applications do so at their own risk and agree to fully indemnify MACOM for any damages resulting from such improper use or sale. 7 M/A-COM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice. Visit www.macom.com for additional data sheets and product information. For further information and support please visit: https://www.macom.com/support