MASWSS0201TR

MASWSS0201 GaAs Broadband 75 Ohm Default-On, SPDT Terminated Switch DC - 2.5 GHz Features             Functional Schematic Ideal for CATV, DTV, DVR, STB Applications Default-On in Unpowered State (RFC-RF1 Path) Broadband Performance: DC-2.5 GHz Low Insertion Loss: 1.1 dB at 1 GHz High Isolation: > 60dB @ 100MHz Single Control Operation Power Handling: > 20 dBm P1dB Lead-Free 3 mm 12-lead PQFN Package 100% Matte Tin Plating over Copper Halogen-Free ―Green‖ Mold Compound RoHS* Compliant and 260°C Reflow Compatible Configurable for Non-terminated Operation GND M/A-COM’s MASWSS0201 is a broadband GaAs PHEMT MMIC SPDT terminated switch in a low cost, lead-free 3 mm 12-lead PQFN package. The MASWSS0201 is ideally suited for applications where an unpowered on state is critical in a single control line SPDT terminated switch. The unpowered condition is the same as the VC = 0 condition. This part can also be configured as a reflective switch with minimal impact to the RF performance. RF1 RF2 Term 1 Term 2 GND GND GND Pin Name Description 1 N/C No Connection 2 RF1 Package MASWSS0201SMB Sample Test Board (Includes 5 Samples) 1. Reference Application Note M513 for reel size information. GND Pin No. 1 3000 piece reel N/C Pin Configuration 2 The MASWSS0201 is fabricated using a 0.5 micron gate length GaAs E/D PHEMT process. The process features full passivation for performance and reliability. MASWSS0201TR-3000 GND VC The MASWSS0201 delivers high isolation, low insertion loss and high linearity up to 2.5 GHz. Part Number RFC N/C Description Ordering Information Rev. V1 RF Port 1 3 3 Term 1 GND Termination 1 Ground 4 GND Ground 5 N/C No Connection 6 GND Ground 3 7 Term 2 GND Termination 2 Ground 8 RF2 RF Port 2 9 VC Control 10 GND Ground 11 RFC RF Input 12 GND 13 Paddle Ground 4 RF and DC Ground 2. M/A-COM recommends that all unused (N/C) pins be connected to ground. All data on this datasheet was taken with N/C pins connected to ground. 3. Terminated grounds require DC blocking capacitors; see application schematic. 4. The exposed pad centered on the package bottom must be connected to RF and DC ground. * Restrictions on Hazardous Substances, European Union Directive 2002/95/EC. 1 M/A-COM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice. Visit www.macom.com for additional data sheets and product information. For further information and support please visit: https://www.macom.com/support MASWSS0201 GaAs Broadband 75 Ohm Default-On, SPDT Terminated Switch DC - 2.5 GHz Rev. V1 Electrical Specifications: TA = 25°C, Z0 = 75 , VC = 0 V/3 V, PIN = 0 dBm 5 Parameter Test Conditions Units Min. Typ. Max. Insertion Loss RFC to RF1 (VC = 0V) 100 MHz 1.0 GHz 2.0 GHz dB dB dB — — — 0.9 1.0 1.3 1.75 1.85 — Insertion Loss RFC to RF2 (VC = 3V) 100 MHz 1.0 GHz 2.0 GHz dB dB dB — — — 1.0 1.2 1.5 1.65 1.85 — Isolation 100 MHz 1.0 GHz 2.0 GHz (RFC - RF1) 2.0 GHz (RFC - RF2) dB dB dB dB 60 40 — — 65 45 38 43 — — — — Return Loss DC - 2.0 GHz dB — 25 — IIP2 (VC = 0V / 3V / 5V) Two Tone, +5 dBm/Tone, 10 MHz Spacing 100 MHz 1.0 GHz dBm dBm — — 54 / 51 / 53 72 / 70 / 70 — — IIP3 (VC = 0V / 3V / 5V) Two Tone, +5 dBm/Tone, 10 MHz Spacing 100 MHz 1.0 GHz dBm dBm — — 38 / 38 / 39 41 / 44 / 44 — — Input P1dB (VC = 0V / 3V / 5V) 100 MHz 1.0 GHz dBm dBm — — 21 / 21 / 22 29 / 28 / 29 — — T-rise T-fall 10% to 90% RF 90% to 10% RF µS nS — — 1.4 12 — — Ton Toff 50% control to 90% RF 50% control to 10% RF µS nS — — 1.6 12 — — Transients — mV — 550 — Control Current VC = 3V µA — 250 500 5. Electrical specifications apply to terminated configuration only. Absolute Maximum Ratings 6,7 Truth Table 8,9,10 Parameter Absolute Maximum Control VC RFC-RF1 RFC-RF2 Input Power @ 100 MHz +22 dBm 0 On Off Input Power @ 1 GHz +29 dBm 1 Off On Operating Voltage +8.5 volts Operating Temperature -40°C to +85°C Storage Temperature -65°C to +150°C 8. External DC blocking capacitors are required on all RF ports. 9. 0 = 0 ± 0.1 V, 1 = +2.9 V to +5 V. 10. The unpowered on state is the same as VC=0. 6. Exceeding any one or combination of these limits may cause permanent damage to this device. 7. M/A-COM does not recommend sustained operation near these survivability limits. 2 M/A-COM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice. Visit www.macom.com for additional data sheets and product information. For further information and support please visit: https://www.macom.com/support MASWSS0201 GaAs Broadband 75 Ohm Default-On, SPDT Terminated Switch DC - 2.5 GHz Rev. V1 Typical Performance Curves: TA = 25°C, Z0 = 75  Components per Application Schematic Insertion Loss RFC Return Loss 0 0.0 RFC to RF1 (Vc=0V) RFC to RF1 (Vc=0V) -0.5 RFC to RF2 (Vc=3V) -10 RFC to RF2 (Vc=3V) -1.0 -20 -1.5 -30 -2.0 -40 -2.5 -50 -3.0 0.0 0.5 1.0 1.5 2.0 2.5 0.0 3.0 0.5 1.0 1.5 2.0 2.5 3.0 Frequency (GHz) Frequency (GHz) Isolation (Below 200 MHz) RF1 Return Loss -40 0 RF1 to RFC (Vc=0V) RFC to RF1 (Vc=3V) -50 RF1 Terminated (Vc=3V) -10 RFC to RF2 (Vc=0V) -60 -20 -70 -30 -80 -40 -50 -90 25 50 75 100 125 150 175 200 225 0.0 250 0.5 1.0 1.5 2.0 2.5 3.0 2.5 3.0 Frequency (GHz) Frequency (MHz) Isolation (Above 200 MHz) RF2 Return Loss 0 -20 RF2 to RFC (Vc=3V) RFC to RF1 (Vc=3V) -30 -40 -20 -50 -30 -60 -40 -70 0.0 RF2 Terminated (Vc=0V) -10 RFC to RF2 (Vc=0V) -50 0.5 1.0 1.5 2.0 Frequency (GHz) 2.5 3.0 0.0 0.5 1.0 1.5 2.0 Frequency (GHz) 3 M/A-COM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice. Visit www.macom.com for additional data sheets and product information. For further information and support please visit: https://www.macom.com/support MASWSS0201 GaAs Broadband 75 Ohm Default-On, SPDT Terminated Switch DC - 2.5 GHz Rev. V1 Lead-Free 3 mm 12-lead PQFN† † Reference Application Note M538 for lead-free solder reflow recommendations. Meets JEDEC moisture sensitivity level 1 requirements. Application Schematic 11,12 C1-C5=10000 pf C6=100 pf Qualification Qualified to M/A-COM specification REL-201, Process Flow –2. Handling Procedures Please observe the following precautions to avoid damage: Static Sensitivity Gallium Arsenide Integrated Circuits are sensitive to electrostatic discharge (ESD) and can be damaged by static electricity. Proper ESD control techniques should be used when handling these devices. M/A-COM’s AN3007 Application Note outlines a method for ESD sensitivity mitigation. It can be found at the Tech/Apps section of the MACOM.COM website. 11. Non-connected pins (P1 and P5) are shown connected to ground as recommended. All data on this datasheet was taken with N/C pins connected to ground. 12. Application schematic shown is for terminated configuration. For non-terminated operation Term 1 and Term 2 ground pins are left open. See application section for data in unterminated configuration. 4 M/A-COM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice. Visit www.macom.com for additional data sheets and product information. For further information and support please visit: https://www.macom.com/support MASWSS0201 GaAs Broadband 75 Ohm Default-On, SPDT Terminated Switch DC - 2.5 GHz Rev. V1 Application Section Typical Performance Curves: TA = 25°C, Z0 = 75  Unterminated Configuration (Term 1&2 GND pins open) Insertion Loss RFC Return Loss 0 0.0 RFC to RF1 (Vc=0V) RFC to RF1 (Vc=0V) -0.5 RFC to RF2 (Vc=3V) -10 RFC to RF2 (Vc=3V) -1.0 -20 -1.5 -30 -2.0 -40 -2.5 -50 -3.0 0.0 0.5 1.0 1.5 2.0 2.5 0.0 3.0 0.5 1.0 1.5 2.0 2.5 3.0 2.5 3.0 2.5 3.0 Frequency (GHz) Frequency (GHz) RF1 Return Loss Isolation (Below 200 MHz) 0 -40 RFC to RF1 (Vc=3V) -50 -10 RFC to RF2 (Vc=0V) RF1 to RFC (Vc=0V) RF1 Unterminated (Vc=3V) -60 -20 -70 -30 -80 -40 -90 25 50 75 100 125 150 175 200 225 250 -50 0.0 0.5 1.0 Frequency (MHz) 1.5 2.0 Frequency (GHz) RF2 Return Loss Isolation (Above 200 MHz) 0 -20 RFC to RF1 (Vc=3V) -30 RF2 Unterminated (Vc=0V) -40 -20 -50 -30 -60 -40 -70 0.0 RF2 to RFC (Vc=3V) -10 RFC to RF2 (Vc=0V) -50 0.5 1.0 1.5 2.0 Frequency (GHz) 2.5 3.0 0.0 0.5 1.0 1.5 2.0 Frequency (GHz) 5 M/A-COM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice. Visit www.macom.com for additional data sheets and product information. For further information and support please visit: https://www.macom.com/support MASWSS0201 GaAs Broadband 75 Ohm Default-On, SPDT Terminated Switch DC - 2.5 GHz Rev. V1 Application Section Application Schematic – Unterminated Configuration C1-C3 = 10000 pf C4 = 100 pf GND C3 RFC GND VC GND C4 RF1 RF2 C2 C1 N/C N/C GND GND GND 6 M/A-COM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice. Visit www.macom.com for additional data sheets and product information. For further information and support please visit: https://www.macom.com/support MASWSS0201 GaAs Broadband 75 Ohm Default-On, SPDT Terminated Switch DC - 2.5 GHz Rev. V1 M/A-COM Technology Solutions Inc. All rights reserved. Information in this document is provided in connection with M/A-COM Technology Solutions Inc ("MACOM") products. These materials are provided by MACOM as a service to its customers and may be used for informational purposes only. Except as provided in MACOM's Terms and Conditions of Sale for such products or in any separate agreement related to this document, MACOM assumes no liability whatsoever. MACOM assumes no responsibility for errors or omissions in these materials. MACOM may make changes to specifications and product descriptions at any time, without notice. MACOM makes no commitment to update the information and shall have no responsibility whatsoever for conflicts or incompatibilities arising from future changes to its specifications and product descriptions. No license, express or implied, by estoppels or otherwise, to any intellectual property rights is granted by this document. THESE MATERIALS ARE PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, RELATING TO SALE AND/OR USE OF MACOM PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, CONSEQUENTIAL OR INCIDENTAL DAMAGES, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. MACOM FURTHER DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. MACOM SHALL NOT BE LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS, WHICH MAY RESULT FROM THE USE OF THESE MATERIALS. 7 MACOM products are not intended for use in medical, lifesaving or life sustaining applications. MACOM customers using or selling MACOM products for use in such applications do so at their own risk and agree to fully indemnify MACOM for any damages resulting from such improper use or sale. M/A-COM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice. Visit www.macom.com for additional data sheets and product information. For further information and support please visit: https://www.macom.com/support