Agamem Microelectronics Inc.
PRELIMINARY ■ DESCRIPTION
AA51880
SERVO MOTOR CONTROLLER
The AA51880 is a BJT integrated circuit using in servo motor control applications. The built-in voltage regulator provides the AA51880 with extremely stable output voltage. It also incorporates a linear one-shot and pulse-width demodulator for improved positional accuracy. ■ FEATURES • Built-in voltage regulator. • Larger driving capability. • Internal output NPN power transistor. • Adjustable dead band range control. • Incorporates a protection circuit for "H-Bridge" driving configuration. • Small outline package. ■ APPLICATIONS • Servo motor control. • Radio controlled car, boat, and airplane. • IA products (such as air-condition). • Remote positioning. ■ BLOCK DIAGRAM
Note: Pin no. is for AA51880C/AA51880F; please refer to “PIN DESCRIPTION” for other package type.
©Copyright Agamem Microelectronics Inc.
1
www.agamem.com.tw
2008/4/22
AGAMEM MICROELECTRONICS INCOPERATION RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. AGAMEM DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCTS OR CIRCUIT DESRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS.
Agamem Microelectronics Inc.
PRELIMINARY ■ PIN DESCRIPTION
AA51880
SERVO MOTOR CONTROLLER
PIN NO. SSOP16 DIP14 1 2 3 5 6 7 8 9 10 11 4,12,13 14 1 3 6 8 7 12 9 10 5 4
PIN NAME RT EXP1 OUT1 OUT2 EXP2 CST NC VREG VCC RDB GND Timing Resistor
FUNCTION
External PNP Transistor 1 output Output Driver 1 Output Driver 2 External PNP Transistor 2 output Stretcher capacitor No Connection Regulated Voltage output Power supply pin Error pulse output Ground pin
2 www.agamem.com.tw 2008/4/22
©Copyright Agamem Microelectronics Inc.
AGAMEM MICROELECTRONICS INCOPERATION RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. AGAMEM DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCTS OR CIRCUIT DESRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS.
Agamem Microelectronics Inc.
PRELIMINARY PIN NO. SSOP16 DIP14 14 15 16 2 11 13 VIN POT CT Input signal Servo position voltage Timing Capacitor
AA51880
SERVO MOTOR CONTROLLER
PIN NAME
FUNCTION
■ ABSOLUTE MAXIMUM RATINGS
Ta=25℃
SYMBOL PARAMETER Vcc Pd Tstg Supply voltage Power dissipation Storage temperature range
RATINGS 4.8~7 300 -25~+125
UNIT V mW ℃
■ ELECTRICAL CHARACTERISTICS
Ta=25℃, Vcc=4.8V
SYMBOL ICC VOL VOH IPNP VREG IREG
PARAMETER Operating current Output voltage "L" Output voltage "H"
TEST CONDITIONS When output is OFF When output is ON Load resistor 20Ω Load resistor 240Ω
LIMITS UNIT MIN TYP MAX 5 8 mA 3.5 30 2.3 4 25 0.1 2.45 28 0.2 2.6 mA V V mA V mA
External PNP transistor Load resistor 240Ω drive current Regulator output voltage Regulator output current Load capacitor 0.1uF Load resistor 500Ω
©Copyright Agamem Microelectronics Inc.
3
www.agamem.com.tw
2008/4/22
AGAMEM MICROELECTRONICS INCOPERATION RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. AGAMEM DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCTS OR CIRCUIT DESRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS.
Agamem Microelectronics Inc.
PRELIMINARY ■ FUNCTIONAL DESCRIPTION (1) Voltage Regulator
AA51880
SERVO MOTOR CONTROLLER
This circuit is composed of a band gap circuit, and outputs a 2.45-volt temperature compensated reference voltage. This reference voltage is stabilized when the supply voltage is variable. (2) Saw tooth wave & One-Shot Generator Connect a capacitor to CT pin will generate a triangular wave by constant current charging. A typical value is 0.1uF. The constant current is determined by a resistor connected to RT pin. A typical capacitor of approximately 0.1uF should be connected in parallel with the resistor to increase stability. (3) Servo Position & Over-Time logic This circuitry consists of a pulse width comparator, which compares the servo position detection signal (POT pin) from the one-shot timer (CT pin) whose period depends on the resistance of a potentiometer connected to the servo's drive shaft. This feedback is what provides the stability for the control circuitry. (4) Pulse Stretcher The difference between the servo control signal and the feedback signal is the error signal. This error signal is used to toggle the direction the current flows through the servo. The function of this pulse stretcher is to “stretch” the small error signal long enough and increases the duty cycle to the motor for it can maintain sufficient holding force. The circuit also implements a “dead band” function that prevents servo jitter and hunting. This is a range over which differences between the input and reference signals will not cause servo operation. When the signal differences exceed this “dead band” range, drive to the motor occurs. servo’s drive shaft. The dead band will change according to the value of resistor connected to the RDB pin. (5) Directional Logic Control The comparator circuit compares pulses from the servo control input (VIN pin) and the voltage controlled pulse generator and provides either a positive or a negative output depending on whether the signal pulse width is larger or smaller than the position generator’s output pulse (POT pin). Application of this error voltage to the motor driver circuit causes the motor to turn in a direction that will minimize the error until both pulse widths are the same. (6) PWM Control This signal generated by directional logic control block is used to control a flip-flop that toggles the direction the current flows through the motor. The outputs of the flip-flop drive an H-Bridge output driver block that handles the high current going through the motor. This blocks output will be turned on or off with each input pulse based on the status of the directional logic. The
©Copyright Agamem Microelectronics Inc. 4 www.agamem.com.tw 2008/4/22
AGAMEM MICROELECTRONICS INCOPERATION RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. AGAMEM DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCTS OR CIRCUIT DESRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS.
Agamem Microelectronics Inc.
PRELIMINARY
AA51880
SERVO MOTOR CONTROLLER
PWM drive techniques provide the benefits of reduced power dissipation, improved servo motor performance and positively affect system efficiency. (7) Output driver The output driver controls the servo current direction. For light load application, the servo can be connected with OUT1 and OUT2 pin only. For heavy load application, the EXP1 and EXP2 pin will be connected to the base of the external PNP transistor. It drives in an H-bridge configuration (The sink NPN drivers are built inside the chip). ■ TYPICAL APPLICATION EXAMPLE
A. Mini-Servo Application (No external drivers needed) VCC
10 EXP1 2
C8 103pF
OUT1 3 VIN 14 OUT2 EXP2 5 6
VR1 5KΩ
VREG 9 RT 1 CT 16 POT 15 RDB CST GND GND GND 11 R3 1KΩ C3 0.1uF C1 0.1uF C2 0.1uF 7 4 12 13 R1 470KΩ
R7 1KΩ
R2 20KΩ
R4 150KΩ C4 0.22uF C5 4.7uF
©Copyright Agamem Microelectronics Inc.
5
www.agamem.com.tw
2008/4/22
AGAMEM MICROELECTRONICS INCOPERATION RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. AGAMEM DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCTS OR CIRCUIT DESRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS.
Agamem Microelectronics Inc.
PRELIMINARY
B. Half H-Bridge application using two external PNP drivers
AA51880
SERVO MOTOR CONTROLLER
C. Full H-Bridge application using two PNPs and two NPNs
©Copyright Agamem Microelectronics Inc.
6
www.agamem.com.tw
2008/4/22
AGAMEM MICROELECTRONICS INCOPERATION RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. AGAMEM DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCTS OR CIRCUIT DESRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS.
Agamem Microelectronics Inc.
PRELIMINARY
AA51880
SERVO MOTOR CONTROLLER
D. Full H-Bridge application using two PMOSs and two NMOSs
Note: Pin no. is for AA51880C, please refer to “PIN DESCRIPTION” for other package type.
■ ORDERING INFORMATION ORDER NO. AA51880C PACKAGE SSOP 16L PACKING TAPE & REEL Q’TY 2,500ea MARK CHART
AA51880 XXXX C AA51880 XXXX F AA51880 XXXXP
AA51880F
SSOP 16L(FD)
TAPE & REEL
2,500ea
AA51880P
DIP 14L
TUBE
7
25ea
©Copyright Agamem Microelectronics Inc.
www.agamem.com.tw
2008/4/22
AGAMEM MICROELECTRONICS INCOPERATION RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. AGAMEM DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCTS OR CIRCUIT DESRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS.
Agamem Microelectronics Inc.
PRELIMINARY ■ PACKAGE DIMENSIONS
AA51880
SERVO MOTOR CONTROLLER
16-pin Plastic SSOP
C
theta
12°(4X)
D
e DIMENSIONS IN MILLIMETERS MIN NOM MAX 1.35 0.10 --0.20 0.19 4.80 5.80 3.80 --0.40 --0° 1.60 --1.45 0.25 --------0.64 ------1.75 0.25 --0.30 0.25 5.00 6.20 4.00 --1.27 0.10 8°
b
SYMBOLS A A1 A2 b C D E E1 e L y theta
DIMENSIONS IN INCHES MIN NOM MAX 0.053 0.004 --0.008 0.007 0.189 0.228 0.150 --0.016 --0° 0.064 --0.057 0.010 --------0.025 ------0.069 0.010 --0.012 0.010 0.197 0.244 0.157 --0.050 0.004 8°
NOTE 1. PACKAGE BODY SIZES EXCLUDE MOLD FLASH PROTRUSIONS OR GATE BURRS 2. DIMENSION L IS MEASURED IN GAGE PLANE 3. TOLERANCE +/- 0.1 mm UNLESS OTHERWISE SPECIFIED 4. CONTROLLING DIMENSION IS MILLIMETER. CONVERTED INCH DIMENSIONS ARE NOT NECESSARILY EXACT. 5. FOLLOWED FROM JEDEC MO-137
©Copyright Agamem Microelectronics Inc.
8
www.agamem.com.tw
2008/4/22
AGAMEM MICROELECTRONICS INCOPERATION RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. AGAMEM DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCTS OR CIRCUIT DESRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS.
Agamem Microelectronics Inc.
PRELIMINARY
AA51880
SERVO MOTOR CONTROLLER
©Copyright Agamem Microelectronics Inc.
9
www.agamem.com.tw
2008/4/22
AGAMEM MICROELECTRONICS INCOPERATION RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. AGAMEM DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCTS OR CIRCUIT DESRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS.
Agamem Microelectronics Inc.
PRELIMINARY
AA51880
SERVO MOTOR CONTROLLER
14-pin DIP
SYMBOLS A A1 A2 D E E1 L eB θ
。
MIN. --0.015 0.125 0.735 0.245 0.115 0.335 0
NOR. ----0.130 0.750 0.250 0.130 0.355 7
MAX. 0.210 --0.135 0.775 0.255 0.150 0.375 15
0.300 BSC.
UNIT : INCH
NOTES: 1. JEDEC OUTLINE : MS-001 AA 2. “D”, “E1” DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.010 INCH. 3. eB IS MEASURED AT THE LEAD TIPS WITH THE LEADS UNCONSTRAINED. 4. POINTED OR ROUNDED LEAD TIPS ARE PREFERRED TO EASE INSERTION. 5. DISTANCE BETWEEN LEADS INCLUDING DAM BAR PROTRUSIONS TO BE 0.005 INCH MININUM. DATUM PLANE “H” COINCIDENT WITH THE BOTTOM OF LEAD WHERE LEAD EXITS BODY.
■ NOTES ON USE • The application circuit examples explain typical applications of the products, and do not guarantee the success of any specific mass-production design. • Application circuit diagrams and circuit constants contained herein are shown as examples of standard use and operation. Please pay careful attention to the peripheral conditions when designing circuits and deciding upon circuit constants in the set. • Take account of common impedance when designing the earth line on a printed wiring board.
©Copyright Agamem Microelectronics Inc.
10
www.agamem.com.tw
2008/4/22
AGAMEM MICROELECTRONICS INCOPERATION RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. AGAMEM DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCTS OR CIRCUIT DESRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS.
很抱歉,暂时无法提供与“AA51880C”相匹配的价格&库存,您可以联系我们找货
免费人工找货