AM10CW-2405D-NZ

Series AM10CW-NZ 10 Watt | DC-DC Converter FEATURES: • • • • • Wide 4:1 Input Voltage Range High efficiency up to 88% 1500 VDC Isolation Over Current Protection No load consumption ≤ 0.12W • • • • • Operating Temperature -40ºC to +85ºC Output Over Voltage protection Continuous Short Circuit Protection Input Under Voltage Protection Remote On/Off control Models Single output Model Input Voltage (V) Output Voltage (V) Output Current max (A) AM10CW-2403S-NZ 9-36 3.3 2.4 AM10CW-2405S-NZ 9-36 5 2 AM10CW-2409S-NZ 9-36 9 1.11 AM10CW-2412S-NZ 9-36 12 0.83 AM10CW-2415S-NZ 9-36 15 0.66 AM10CW-2424S-NZ 9-36 24 0.41 AM10CW-4803S-NZ* 18-75 3.3 2.4 AM10CW-4805S-NZ* 18-75 5 2 AM10CW-4812S-NZ* 18-75 12 0.83 AM10CW-4815S-NZ* 18-75 15 0.66 AM10CW-4824S-NZ* 18-75 24 0.41 *Need an input capacitor in order to meet CISPR32 / EN55032 Class A. Isolation (VDC) Max Capacitive Load (uF) Efficiency (%) 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 2200 2200 680 470 330 100 2200 2200 470 330 100 78 83 85 86 86 88 79 83 87 87 88 Isolation (VDC) Max Capacitive Load (uF) Efficiency (%) Models Dual output Model Input Voltage (V) Output Voltage (V) Output Current max (A) AM10CW-2405D-NZ* 9-36 ±5 ±1 1500 ±1000 83 AM10CW-2409D-NZ 9-36 ±9 ±0.55 1500 ±680 86 AM10CW-2412D-NZ* 9-36 ±12 ±0.41 1500 ±470 87 AM10CW-2415D-NZ 9-36 ±15 ±0.33 1500 ±330 87 AM10CW-2424D-NZ* 9-36 ±24 ±0.2 1500 ±100 87 AM10CW-4805D-NZ* 18-75 ±5 ±1 1500 ±1000 83 AM10CW-4812D-NZ* 18-75 ±12 ±0.41 1500 ±470 87 AM10CW-4815D-NZ* 18-75 ±15 ±0.33 1500 ±330 87 AM10CW-4824D-NZ* 18-75 ±24 ±0.2 1500 ±100 87 Add suffix “-ST” for optional screw terminal bottom plate or “-STD” for optional DIN Rail screw terminal bottom plate and input reverse polarity protection. Due to the input reverse polarity protection, models with “-ST” and “-STD” option will have their minimum input and start-up voltage increased by 1VDC and efficiency decreased by 2%. *Need an input capacitor in order to meet CISPR32 / EN55032 Class A. NOTE: All specifications in this datasheet are measured at an ambient temperature of 25°C, humidity1,000,000 hours (MIL-HDBK -217F, Ground Benign, t=+25 C) oC Maximum soldering temperature 1.5mm from case for 10 sec 300 * Switching frequency reduces at 0% to 50% load for better efficiency. Environmental Specifications Parameters Vibration www.aimtec.com F 051e R17 REV: 09/23/A Test mode Acceleration 10-150Hz 5G, 90min along all axles Tel: +1 514 620 2722 2 of 5 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM10CW-NZ 10 Watt | DC-DC Converter Safety Specifications Parameters Approval CE, UL IEC/EN/UL60950-1 EN 55032, class A EN 55032, class B (with the recommended EMC circuit EMI part) Electrostatic Discharge Immunity IEC 61000-4-2, Contact ±4KV, Criteria B RF, Electromagnetic Field Immunity IEC 61000-4-3, 10V/m, Criteria A Electrical Fast Transient / Burst Immunity IEC 61000-4-4, ±2KV, Criteria B (with the recommended EMC circuit EMS part) Surge Immunity IEC 61000-4-5, ±2KV, Criteria B (with the recommended EMC circuit EMS part) RF, Conducted Disturbance Immunity IEC 61000-4-6, 3 Vrms, Criteria A Voltage dips, Short Interruptions & IEC 61000-4-29: 0-70%, Criteria B Voltage variations Immunity Standards Derating Free Air Convection 65 ºC 3.3, 5V & ±5V models Output Power (%) 100 71ºC Other models 80 60 Safe Operating Area 40 20 0 - 40 - 20 0 20 40 65 71 60 80 85 100 Ambient Temperature º C Dimensions Pin Out Specifications Bottom View 2.54 (0.10) Top View 25.40 (1.00) 10.16 2.54 (0.40) (0.10) 10.16 (0.40) 5 4 20.32 (0.80) 25.40 (1.00) +V Output +V Input 2.54 (0.10) 1 Side View 10.16 (0.40) 6 -V Output Pin 1 2 3 4 5 6 Single +V Input -V Input On/Off Control +V Output No pin -V Output Dual +V Input -V Input On/Off Control +V Output Common -V Output -V Input CTRL 2 3 5.08 7.62 (0.20) (0.30) 11.70 (0.46) 4.10 (0.16) Printed Face 2.54 (0.10) www.aimtec.com F 051e R17 REV: 09/23/A ᴓ 1.00 (0.39) Dimensions mm (inch) Case Tolerance ±0.50 (±0.02) Pin Diameter 1.0 ± 0.10 (0.04 ± 0.004) Tel: +1 514 620 2722 3 of 5 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM10CW-NZ 10 Watt | DC-DC Converter Dimensions with -ST options Pin Out Specifications 76.00 (2.99) Pin 61.60 (2.43) 1 2 3 4 5 6 LED light 31.50 (1.24) 2 Top view 3 23.00 (0.91) 4 1 5 Single On/Off Control -V Input +V Input -V Output No pin +V Output Dual On/Off Control -V Input +V Input -V Output Common +V Output 6 Ø3.30 Ø0.13 Dimensions: mm (inch) Case Tolerance:± 0.50 (0.02) Wire gauge: 24-12AWG Torque Tightening: Max 0.4N*m 8.80 (0.35) 21.20 (0.84) Side view Dimensions with -STD options Pin Out Specifications 76.00 (2.99) Pin 61.60 (2.43) LED light Top view 3 5 8.80 (0.35) 22.2 (0.87) Side view www.aimtec.com F 051e R17 REV: 09/23/A Dual On/Off Control -V Input +V Input -V Output Common +V Output 6 25.8±1 (1.02±0.04) 31.50 (1.24) 2 Single On/Off Control -V Input +V Input -V Output No Connection +V Output 23.00 (0.91) 4 1 1 2 3 4 5 6 Tel: +1 514 620 2722 4 of 5 Dimensions: mm (inch) Case Tolerance:± 0.50 (0.02) Wire gauge: 24-12AWG Mounting Rail: TS35 Torque Tightening: Max 0.4N*m Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM10CW-NZ 10 Watt | DC-DC Converter Typical application circuits Single Dual Vin+ Vo+ Vin+ Cin + 10uF + Vin- Vo+ + 10uF Com + 10uF Vo- + Cin Vo- Vin- 24V input 100μF Cin 48V input 10-47μF Recommended EMC Circuits For EMS test For EMI test LDM1 4.7μH FUSE + Vin CY1 1nF/2KV + MOV + Vin + C2 C1 C3 - Vin DC - Vin A +Vout + Vout DC - Vout 10μF -Vout CY2 1nF/2KV B MOV C1/C3 C2 24V input S20K30 330µF/50V 1µF/50V 48V input S14K60 330µF/100V 1µF/100V NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the date manufactured. 3. Mechanical drawings and specifications are for reference only. 4. All specifications are measured at an ambient temperature of 25°C, humidity