AM15E-2412S-NZ

Click on Series name for product info on aimtec.com Series AM15E-NZ 15 Watt | DC-DC Converter FEATURES: • • • • • • • • • • Wide 2:1 input range High efficiency up to 90% Input Under Voltage lockout Over current, over voltage protection Remote On/Off Control Operating temperature -40°C to + 85°C Input / Output Isolation 1500VDC Continuous short circuit protection No load power consumption ≤0.12W Output voltage adjustment Models Single output Model Input Voltage (V) Max Input current FL/LL (mA) Output Voltage (V) Output Current max (A) Capacitive load, max (µF) Efficiency (%) 18-36 18-36 18-36 18-36 36-75 36-75 36-75 36-75 718/75 718/10 718/10 718/10 363/30 363/10 363/10 363/10 5 12 15 24 5 12 15 24 3 1.25 1 0.62 3 1.25 1 0.62 4700 1000 820 270 3300 1000 680 470 89 89 89 90 88 88 89 89 AM15E-2405S-NZ AM15E-2412S-NZ AM15E-2415S-NZ AM15E-2424S-NZ AM15E-4805S-NZ AM15E-4812S-NZ AM15E-4815S-NZ AM15E-4824S-NZ NOTE: All specifications in this datasheet are measured at an ambient temperature of 25°C, humidity 1,000,000 hrs (MIL-HDBK -217F, Ground Benign, t=+25oC) oC 1.5 mm from case 10 sec. 300 Environmental Specifications Parameters Vibration Test mode Acceleration 10-55Hz 10G, 30min one cycle, every axis tested Safety Specifications Parameters Approval Standards www.aimtec.com CE, UL IEC/EN/UL 60950-1 EN 55032, class A (without external components), class B (with the recommended EMC circuit) Electrostatic Discharge Immunity IEC 61000-4-2, Contact ±4KV, Criteria B RF, Electromagnetic Field Immunity IEC 61000-4-3, 10V/m, Criteria A Electrical Fast Transient / Burst Immunity IEC 61000-4-4, ±2KV, Criteria B (with the recommended EMC circuit) Surge Immunity IEC 61000-4-5, ±2KV, Criteria B (with the recommended EMC circuit) RF, Conducted Disturbance Immunity IEC 61000-4-6, 3 Vrms, Criteria A Voltage dips, Short Interruptions & Voltage IEC 61000-4-29: 0-70%, Criteria B variations Immunity Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 051e R2 REV: 03/20/A 2 of 5 North America only Series AM15E-NZ 15 Watt | DC-DC Converter Pin Out Specifications Dimensions: 10.16 (0.40) 6 7.62 5.08 (0.30) (0.20) 25.40 (1.00) Top View 10.16 2.54 (0.40) (0.10) Bottom View 3 2 5 1 4 15.24 (0.60) 15.24 (0.60) 20.32 (0.80) 2.54 10.16 (0.10) (0.40) 50.80 (2.00) Pin Single 1 2 3 4 5 6 On/Off Control -Vin +Vin - Vout Trim + Vout 11.80 (0.47) Printed Face Note: Unit: mm (inch) General tolerances: ±0.50 (±0.02) Side View 4.10 (0.16) 1.00 (0.04) Derating Free Air Convection Without heatsink Output Power (%) 100 80 Safe Operating Area 60 40 20 0 - 40 - 20 0 20 40 60 75 80 85 100 Ambient Temperature º C www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 051e R2 REV: 03/20/A 3 of 5 North America only Series AM15E-NZ 15 Watt | DC-DC Converter EMC recommended filter CY1 1nF/2KV L FUSE +VIN +V input +V output 4.7uH DC/DC Converter C1 + MOV C2 Load -V output - V input -VIN C3 CY2 1nF/2KV Model MOV C1 C2 C3 24 Vin S20K30 330 µF / 50V 1 µF / 50V 48 Vin S14K60 330 µF / 100V 1 µF / 100V 470µF for 5V output 220µF for 12/15V output 100 µF for 24V output Trimming Output voltage can be externally trimmed by utilizing the methods as shown below. Leave open if not used. Fixed Resistor Variable Potentiometer AM15E-xx05S-NZ, xx=24 or 48 Trim down % 1 Vout (VDC) Rt down (KΩ) Trim up % Vout (VDC) Rt up (KΩ) www.aimtec.com 4.95 105.181 2 4.9 52.154 3 4.85 31.997 4 4.8 21.378 5 4.75 14.823 6 4.7 10.373 7 4.65 7.155 8 4.6 4.719 9 4.55 2.811 10 4.5 1.277 1 5.05 2 5.1 3 5.15 4 5.2 5 5.25 6 5.3 7 5.35 8 5.4 9 5.45 10 5.5 176.356 71.279 41.973 28.2 20.197 14.967 11.281 8.543 6.430 4.749 Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 051e R2 REV: 03/20/A 4 of 5 North America only Series AM15E-NZ 15 Watt | DC-DC Converter AM15E-xx12S-NZ, xx=24 or 48 Trim down % 1 2 3 4 Vout (VDC) Rt down (KΩ) Trim up % Vout (VDC) 11.88 496.092 1 12.12 11.76 301.452 2 12.24 11.64 212.527 3 12.36 11.52 161.585 4 12.48 Rt up (KΩ) 706.435 158.92 83.879 54.075 38.077 14.85 2 14.7 3 14.55 4 14.4 634.883 400.637 288.514 1 15.15 2 15.3 1460.099 192.574 AM15E-xx15S-NZ, xx=24 or 48 Trim down % 1 Vout (VDC) Rt down (KΩ) Trim up % Vout (VDC) Rt up (KΩ) 5 6 7 8 9 10 11.4 11.28 128.573 105.442 5 6 12.6 12.72 11.16 88.332 7 12.84 11.04 75.164 8 12.96 10.92 64.716 9 13.08 10.8 56.223 10 13.2 28.095 21.274 16.317 12.552 9.595 5 14.25 6 14.1 7 13.95 8 13.8 9 13.65 10 13.5 222.759 179.537 148.96 126.187 108.569 94.532 83.087 3 15.45 4 15.6 5 15.75 6 15.9 7 16.05 8 16.2 9 16.35 10 16.5 96.642 61.354 43.016 31.781 24.191 18.721 14.59 11.361 AM15E-xx24S-NZ, xx=24 or 48 Trim down % 1 2 3 4 5 6 7 8 9 Vout (VDC) 23.76 23.52 23.28 23.04 22.8 22.56 22.32 22.08 21.84 Rt down (KΩ) 1286.2 792.123 565.867 436.104 351.954 292.963 249.315 215.714 189.047 Trim up % 1 2 3 4 5 6 7 8 9 Vout (VDC) 24.24 24.48 24.72 24.96 25.2 25.44 25.68 25.92 26.16 Rt up (KΩ) 816.889 179.914 94.338 60.464 42.307 30.988 23.257 17.64 13.376 10 21.6 167.37 10 26.4 10.027 NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the date manufactured. 3. Mechanical drawings and specifications are for reference only. 4. All specifications are measured at an ambient temperature of 25°C, humidity