AM15EW-11015SH22-NZ

Series AM15EW-NZ 15 Watt | DC-DC Converter FEATURES: • • • • Efficiency up to 85% Ultra-wide 4:1 Input range Continuous short circuit protection Operating Temperature: -40oC to +85oC • • • • On/Off Remote Control Over Voltage & Over Current Protection Input / Output Isolation 2250VDC Input Under Voltage Lockout Models Single output Model Input Voltage (V) Output Voltage (V) Output Current max (mA) Max Capacitive Load (uF) Isolation (VDC) Efficiency (%) AM15EW-11003SH22-NZ 40-160 3.3 4000 2250 5400 82 AM15EW-11005SH22-NZ 40-160 5 3000 2250 5400 84 AM15EW-11012SH22-NZ # 40-160 12 1250 2250 1000 84 AM15EW-11015SH22-NZ 40-160 15 1000 2250 820 85 AM15EW-11024SH22-NZ # 40-160 24 625 2250 270 85 Add suffix “-K” for optional heat sink *Add suffix “-ST” for optional screw terminal bottom plate or “-STD” for optional DIN Rail screw terminal bottom plate and reverse voltage protection. **Add suffix “-K” for optional heatsink, “-K-ST” for optional heatsink and screw terminal bottom plate or “-K-STD” for optional heatsink and DIN Rail screw terminal bottom plate and reverse voltage protection. NOTE: All specifications in this datasheet are measured at an ambient temperature of 25°C, humidity1000 2000 110Vin 2250V Isolation, I/O, 100KHz/0.1V Maximum Units VDC VDC MOhm pF Output Specifications Parameters Voltage accuracy Over voltage protection Over current protection Short Circuit protection Short circuit restart Line voltage regulation Load voltage regulation Temperature coefficient Ripple & Noise Voltage adjustment range Transient recovery time Transient recovery deviation www.aimtec.com F 051e R13.E REV: 07/22/A Conditions Typical Maximum Units 210 % % % of Io ±3 Zener Diode Clamp 120 Hiccup, Continuous Auto-Recovery Full load, LL-HL 0-100% load for 2250V instead models; 5-100% load others ±0.5 ±1 ±0.03 100 ±10 500 20MHz Bandwidth 25% load step change 25% load step change Tel: +1 514 620 2722 1 of 7 ±5 % of Vin % %/oC mV p-p % µS % Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM15EW-NZ 15 Watt | DC-DC Converter General Specifications Parameters Switching frequency Operating temperature Storage temperature Maximum case temperature Cooling Humidity Case material Dimensions (L x W x H) Weight MTBF Maximum soldering temperature Conditions Typical 100% load See derating curve 300 Maximum Units 105 KHz o C oC oC -40 to +85 -55 to +125 Free air convection 95 % RH Aluminum Alloy PCB mountable without heatsink 2.00 x 1.00 x 0.46 inches; 50.80 x 25.40 x 11.80mm Optional packages See dimensions drawing Pin mountable without heatsink 26 (2250VDC Isolated models) Pin mountable with heatsink 34 (2250VDC Isolated models) -ST option without heatsink 48 (2250VDC Isolated models) g -ST option with heatsink 56 (2250VDC Isolated models) -STD option without heatsink 68 (2250VDC Isolated models) -STD option with heatsink 76 (2250VDC Isolated models) o >1,000,000 hours (MIL-HDBK -217F, Ground Benign, t=+25 C) oC 1.5mm from case for 10 sec 300 Environmental Specifications Parameters Vibration (110 Vin/2250VDC isolation) IEC61373 car body 1 B mold Safety Specifications Parameters CE, EN62368-1; cULus UL62368-1 (# 110V input 12V, 24V output models only) EN 55022, class B (with the recommended EMC circuit) IEC61000-4-2, Contact ±6KV (110Vin 2250V Isolation), Criteria B IEC61000-4-3, 10V/m, Criteria A IEC61000-4-4, ±4KV (110Vin 2250V Isolation), Criteria B IEC61000-4-5, ±2KV, Criteria B, (with the recommended EMC circuit) IEC61000-4-6, 10 Vrms (2250 VDC Isolated models) Criteria A Design to meet IEC/EN/UL 60950-1, EN50155 IEC/EN/UL 62368 approved (AM15EW-11012SH22-NZ & AM15EW-11024SH22-NZ models only) Pin Out Specifications Dimensions 10.16 (0.40) 6 3 Bottom View 4.10 (0.16) 11.80 (0.47) www.aimtec.com F 051e R13.E REV: 07/22/A Tel: +1 514 620 2722 2 of 7 5 2 4 20.32 (0.80) 2.54 (0.10) 1 15.24 (0.60) DIA 1.00 (0.04) 2.54 (0.10) 50.80 (2.00) 7.62 5.08 (0.30) (0.20) Single On/Off Control -Vin +Vin -Vout Trim +Vout 25.40 (1.00) Pin 1 2 3 4 5 6 10.16 (0.40) Standards 10.16 (0.40) Approvals 15.24 (0.60) Notes: All dimensions are typical in millimeters (inches). Pin diameter Tolerance ±0.10 (±0.004) Case Tolerance ±0.50 (±0.02) Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM15EW-NZ 15 Watt | DC-DC Converter Pin Out Specifications 16.50 (0.65) Optional -K heatsink Pin 1 2 3 4 5 6 4.10 (0.16) Side view 2.94 (0.12) DIA 1.00 (0.04) 10.16 (0.40) 10.56 (0.42) 6 7.62 5.08 (0.30) (0.20) 3 Bottom View 5 10.16 (0.40) 2 1 15.54 (0.61) Single On/Off Control -Vin +Vin -Vout Trim +Vout 20.32 (0.80) 2.94 (0.12) 4 15.54 (0.61) Notes: All dimensions are typical in millimeters (inches). Pin diameter Tolerance: ±0.10 (±0.004) Case Tolerance: ±0.50 (±0.02) Dimensions with -ST options Pin Out Specifications 76.00 (2.99) 61.60 (2.43) LED light 2 6 Top view 3 23.00 (0.91) 31.50 (1.24) 1 5 Pin Single 1 2 3 4 5 6 On/Off Control -Vin +Vin + Vout Trim - Vout 4 8.80 (0.35) Side view 21.20 (0.84) Dimensions: mm (inch) Case Tolerance:± 0.50 (0.02) Wire gauge: 24-12AWG www.aimtec.com F 051e R13.E REV: 07/22/A Tel: +1 514 620 2722 3 of 7 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM15EW-NZ 15 Watt | DC-DC Converter Dimensions with -STD options Pin Out Specifications 76.00 (2.99) 61.60 (2.43) LED light 6 Top view 2 23.00 (0.91) 31.50 (1.24) 1 5 3 Pin Single 1 2 3 4 5 6 On/Off Control -Vin +Vin + Vout Trim - Vout 4 9.80 (0.39) Ø3.30 Ø0.13 25.80 (1.02) Side view Dimensions: mm (inch) Case Tolerance:± 1.00 (0.04) Wire gauge: 24-12AWG Dimensions with heatsink and -ST options Pin Out Specifications 76.00 (2.99) 61.60 (2.43) LED light 2 6 Top view 3 Single 1 2 3 4 5 6 On/Off Control -Vin +Vin + Vout Trim - Vout 23.00 (0.91) 31.50 (1.24) 1 Pin 5 4 21.20 (0.84) Side view 8.80 (0.35) 25.30 (1.00) Dimensions: mm (inch) Case Tolerance:± 0.50 (0.02) Wire gauge: 24-12AWG www.aimtec.com F 051e R13.E REV: 07/22/A Tel: +1 514 620 2722 4 of 7 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM15EW-NZ 15 Watt | DC-DC Converter Dimensions with heatsink and -STD options Pin Out Specifications 76.00 (2.99) 61.60 (2.43) LED light 6 Top view 2 5 3 Single 1 2 3 4 5 6 On/Off Control -Vin +Vin + Vout Trim - Vout 23.00 (0.91) 31.50 (1.24) 1 Pin 4 9.80 (0.39) Ø3.30 Ø0.13 25.80 (1.02) 29.90 (1.18) Side view Dimensions: mm (inch) Case Tolerance:± 0.50 (0.02) Wire gauge: 24-12AWG Trimming Output voltage can be externally trimmed by utilizing the methods as shown below Fixed Resistor Variable Potentiometer Leave open if not used. www.aimtec.com F 051e R13.E REV: 07/22/A Tel: +1 514 620 2722 5 of 7 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM15EW-NZ 15 Watt | DC-DC Converter AM15EW-11003SH22-NZ Trim down % 1 2 3 4 5 6 7 8 9 10 Vout (VDC) 3.267 3.234 3.201 3.168 3.135 3.102 3.069 3.036 3.003 2.97 Rt down (KΩ) 210.002 103.334 72.327 54.213 42.335 31.667 25.963 21.505 16.884 14.124 Trim up % 1 2 3 4 5 6 7 8 9 10 Vout (VDC) 3.333 3.366 3.399 3.432 3.465 3.498 3.531 3.564 3.597 3.63 Rt up (KΩ) 369.179 96.88 59.466 41.454 28.235 22.058 17.6 14.23 10.837 8.857 2 3 4 5 6 7 8 9 10 AM15EW-11005SH22-NZ Trim down % 1 Vout (VDC) 4.95 4.9 4.85 4.8 4.75 4.7 4.65 4.6 4.55 4.5 Rt down (KΩ) 105.181 52.154 31.997 21.378 14.823 10.373 7.155 4.719 2.811 1.277 Trim up % 1 2 3 4 5 6 7 8 9 10 Vout (VDC) 5.05 5.1 5.15 5.2 5.25 5.3 5.35 5.4 5.45 5.5 Rt up (KΩ) 176.356 71.279 41.974 28.2 20.198 14.967 11.281 8.544 6.43 4.749 2 3 4 5 6 7 8 9 10 AM15EW-11012SH22-NZ Trim down % 1 Vout (VDC) 11.88 11.76 11.64 11.52 11.4 11.28 11.16 11.04 10.92 10.8 Rt down (KΩ) 496.092 301.452 212.527 161.585 128.573 105.442 88.332 75.164 64.716 56.223 Trim up % 1 2 3 4 5 6 7 8 9 10 Vout (VDC) 12.12 12.24 12.36 12.48 12.6 12.72 12.84 12.96 13.08 13.2 Rt up (KΩ) 706.435 158.92 83.879 54.075 38.077 28.095 21.274 16.317 12.552 9.595 2 3 4 5 6 7 8 9 10 AM15EW-11015SH22-NZ Trim down % 1 Vout (VDC) 14.85 14.7 14.55 14.4 14.25 14.1 13.95 13.8 13.65 13.5 Rt down (KΩ) 974.008 517.391 346.387 256.863 201.789 164.487 137.551 117.187 101.251 88.44 Trim up % 1 2 3 4 5 6 7 8 9 10 Vout (VDC) 15.15 15.3 15.45 15.6 15.75 15.9 16.05 16.2 16.35 16.5 Rt up (KΩ) 283.713 117.996 70.541 48.045 34.918 26.315 20.242 15.725 12.235 9.456 2 3 4 5 6 7 8 9 10 AM15EW-11024SH22-NZ Trim down % 1 Vout (VDC) 23.76 23.52 23.28 23.04 22.8 22.56 22.32 22.08 21.84 21.6 Rt down (KΩ) 1286.2 792.123 565.867 436.104 351.954 292.963 249.316 215.714 189.047 167.37 Trim up % 1 2 3 4 5 6 7 8 9 10 Vout (VDC) 24.24 24.48 24.72 24.96 25.2 25.44 25.68 25.92 26.16 26.4 Rt up (KΩ) 816.889 179.914 94.338 60.464 42.307 30.988 23.257 17.64 13.376 10.027 www.aimtec.com F 051e R13.E REV: 07/22/A Tel: +1 514 620 2722 6 of 7 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM15EW-NZ 15 Watt | DC-DC Converter Derating 110Vin 2250V Isolation Free Air Convection 65 ºC Output Power (%) 100 without heatsink 71ºC with heatsink 80 60 Safe Operating Area 40 20 0 - 20 - 40 0 20 40 65 71 60 80 85 100 Ambient Temperature º C EMC recommended filter 110Vin 2250V Isolation CY1 1nF/400VAC LCM1 15mH LCM2 15mH +Vin -Vin C2 C1 220nF/250V 100µF/200V C3 220nF/250V +Vo CY3 C4 CY4 DC-DC Converter C5 -Vo CY2 1nF/400VAC CY3 & CY4 1nF / 400V C4 Vout C5 10-47 µF / 250V 3.3V & 5V 12V & 15V 24V 470 µF 220 µF 100 µF NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the date manufactured. 3. Mechanical drawings and specifications are for reference only. 4. All specifications are measured at an ambient temperature of 25°C, humidity