AM15T-2415DZ

Click on Series name for product info on aimtec.com Series AM15T-Z 15Watt | DC-DC Converter FEATURES: • • • • • • • • • • Wide Input Range 2:1 1600 Vdc Isolation Efficiency up to 91% Soft Start Remote On/Off Function No Minimum Load Required -40ºC to +85ºC Operating Temperature Range Short Circuit & Over Voltage Protection DIP 24 Package Low No Load Input Current Models Single output Model Input Voltage (V) Output Voltage (V) Output Current max (mA) Isolation (VDC) Maximum Capacitive load (µF) Efficiency (%) 9-18 9-18 9-18 9-18 18-36 18-36 18-36 18-36 36-75 36-75 36-75 36-75 3.3 5.1 12 15 3.3 5.1 12 15 3.3 5.1 12 15 4000 3000 1250 1000 4000 3000 1250 1000 4000 3000 1250 1000 1600 1600 1600 1600 1600 1600 1600 1600 1600 1600 1600 1600 4700 3300 600 400 4700 3300 600 400 4700 3300 600 400 86 89 89 90 87 89 90 91 86 88 89 89 Input Voltage (V) Output Voltage (V) Output Current max (mA) Isolation (VDC) Maximum Capacitive load (µF) Efficiency (%) 9-18 9-18 9-18 18-36 18-36 18-36 36-75 36-75 36-75 ±5 ±12 ±15 ±5 ±12 ±15 ±5 ±12 ±15 ±1500 ±625 ±500 ±1500 ±625 ±500 ±1500 ±625 ±500 1600 1600 1600 1600 1600 1600 1600 1600 1600 ±1500 ±288 ±200 ±1500 ±288 ±200 ±1500 ±288 ±200 86 90 90 86 90 90 86 89 90 AM15T-1203SZ AM15T-12051SZ AM15T-1212SZ AM15T-1215SZ AM15T-2403SZ AM15T-24051SZ AM15T-2412SZ AM15T-2415SZ AM15T-4803SZ AM15T-48051SZ AM15T-4812SZ AM15T-4815SZ Models Dual output Model AM15T-1205DZ AM15T-1212DZ AM15T-1215DZ AM15T-2405DZ AM15T-2412DZ AM15T-2415DZ AM15T-4805DZ AM15T-4812DZ AM15T-4815DZ NOTE: All specifications in this datasheet are measured at an ambient temperature of 25°C, humidity1000 2000 Output Specifications Parameters Conditions Typical Voltage accuracy Voltage balance 1st output 25-100% load, 2nd output 100% load Single, HL-LL Line voltage regulation Dual, HL-LL Single, 0% Load to 100% load Load voltage regulation Dual, 0% to 100% load, balance load Zener diode clamp, 3.3Vout 3.9 Zener diode clamp, 5.1Vout 6.2 Zener diode clamp, 12Vout 15 Over voltage protection Zener diode clamp, 15Vout 18 Zener diode clamp, ±5Vout ±6.2 Zener diode clamp, ±12Vout ±15 Zener diode clamp, ±15Vout ±18 Over current protection Full Load 150 Short Circuit protection Continuous Short circuit restart Auto recovery Ripple & Noise* 20MHz Bandwidth * Measured with a 1µF ceramic capacitor General Specifications Parameters Switching frequency Operating temperature Storage temperature Max Case temperature Temperature coefficient Derating Cooling Humidity Case material Potting material Weight Dimensions (L x W x H) MTBF Manual soldering temperature www.aimtec.com F 051e R12.B Rev: 08/21/A Conditions Typical Full Load with Derating above 60ºC 250 to 330 -40 to +85 -55 to +125 105 ±0.02 2.5 Free air convection Above 60ºC KHz °C °C °C %/°C %/°C 95 % RH Nickel-coated Copper UL94V-0 rated 20.0 g Tolerance ±0.5 mm or ±0.02 inches 1.25 x 0.8 x 0.4inches 31.8 x 20.3 x 10.2mm > 460 000 hrs (MIL-HDBK -217F, Ground Benign, t=+25°C) °C 1.5mm from case for 10sec 260 Tel: +1 514 620 2722 2 of 3 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM15T-Z 15Watt | DC-DC Converter Safety Specifications Parameters CE Designed to meet IEC/EN/UL60950-1, 62368-1 EN55032 Class A IEC61000-4-2, Perf. Criteria B IEC61000-4-3, Perf. Criteria A IEC61000-4-4, Perf. Criteria B (requires 2 external cap 330uF/100V or 1 cap 680 uF/100V for parallel connection) IEC61000-4-5, Perf. Criteria B (requires 2 external cap 330uF/100V or 1 cap 680 uF/100V for parallel connection) IEC61000-4-6, Perf. Criteria A IEC61000-4-8, Perf. Criteria A Pin Out Specifications Dimensions 1 2 3 9 11 14 16 22 23 Remote On/Off -V Input -V Input No Pin N.C. +V Output -V Output +V Input +V Input Remote On/Off -V Input -V Input Common -V Output +V Output Common +V Input +V Input 22.86 (0.9) 31.80 (1.25) 4.42 (0.17) 1 2 3 Stand off Ø1.00 (0.04) 9 11 Bottom View 23 22 5.01 (0.19) Dual 20.30 (0.8) Single 3.00 (0.12) 0.50 (0.02) Pin 15.24 (0.6) Standards 16 2.54 (0.1) 14 5.08 (0.2) 10.20 (0.4) Agency Approval All dimensions are typical: millimeters (inches) Pin Diameter: 0.50 ± 0.05 (0.02 ± 0.002) Pin Pitch tolerance: ± 0.35 (±0.014) Case tolerance: ± 0.5 (±0.02) Stand off tolerance: ± 0.1 (±0.004) Derating Free Air Convection 60º C Output Power (%) 100 80 Safe Operating Area 60 40 30 20 0 - 40 - 20 0 20 40 60 80 85 100 Ambient Temperature º C NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the date manufactured. 3. Mechanical drawings and specifications are for reference only. 4. All specifications are measured at an ambient temperature of 25°C, humidity