AM1LO-0305SH421

Click on Series name for product info on aimtec.com Series AM1LO 1 Watt | DC-DC Converter FEATURES: • I/O Isolation 4200VDC • Operating temperature -40oC to + 105oC • Rated working voltage 250Vrms/400VDC • • • SMD open frame package Efficiency up to 78% High MTBF of over 7Mh Models Single output Model AM1LO-0303SH421 AM1LO-0305SH421 AM1LO-0503SH421 AM1LO-0505SH421 Input Voltage (V) Output Voltage (V) 2.97-3.63 2.97-3.63 4.5-5.5 4.5-5.5 3.3 5 3.3 5 Input Voltage (V) Output Voltage (V) 2.97-3.63 2.97-3.63 4.5-5.5 4.5-5.5 ±3.3 ±5 ±3.3 ±5 Output Current Max | Min (mA) 303 200 303 200 30 20 30 20 Input Current Full | No Load (mA) 416 404 274 264 Isolation (VDC) Max Capacitive Load (uF) Efficiency (%) 4200 4200 4200 4200 220 220 220 220 73 75 73 76 Isolation (VDC) Max Capacitive Load (uF) Efficiency (%) 4200 4200 4200 4200 ±100 ±100 ±100 ±100 75 78 75 78 50 50 40 40 Models Dual output Model AM1LO-0303DH421 AM1LO-0305DH421 AM1LO-0503DH421 AM1LO-0505DH421 Output Current Max | Min (mA) ±151 ±100 ±151 ±100 ±15 ±10 ±15 ±10 Input Current Full | No Load (mA) 404 389 267 257 50 50 40 40 NOTE: 1. Add suffix “TR” to a part number when ordering in tape and reel package. NOTE: 2. All specifications in this datasheet are measured at an ambient temperature of 25°C, humidity1000 25 Output Specifications Parameters Voltage accuracy Short Circuit protection Line voltage regulation Load voltage regulation Temperature coefficient www.aimtec.com F 051e R12.I Conditions Typical Maximum Units ±1.2 ±15 ±12 % of Vin See tolerance chart Momentary, 0.5s For ±1% of Vin 3.3V output 10% - 100% load 5V output 100% load Tel: +1 514 620 2722 1 of 6 ±0.03 % %/oC Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM1LO 1 Watt | DC-DC Converter Single output 20MHz Bandwidth Dual output *Ripple and Noise measured with a 10uF EC and 0.1uF CC. ±150 ±120 Ripple & Noise* mV p-p General Specifications Parameters Conditions Switching frequency Operating temperature Storage temperature Cooling Humidity Base material Typical Maximum Units 50-80 With derating above +100 KHz oC oC -40 to +105 -55 to +125 Free air convection (30-65LFM) Non-Condensing 95 Non-conductive black plastic (UL94-V0) Single output models 1.52 Dual output models 1.80 0.50 x 0.44 x 0.27 inches Single output models x 6.85 mm 0.60 x 0.44 x 0.27 inches Dual output models x 6.85 mm >7Mhrs (MIL-HDBK -217F, Ground Benign, t=+25oC) 10 sec max 245 Weight Dimensions (L x W x H) MTBF Reflow temperature % RH g 12.70 x 11.20 15.24 x 11.20 oC Environmental Specifications Parameters Vibration Test mode Per MIL-STD-810F Safety Specifications Parameters CE, UL, IEC/EN/UL60950-1 & IEC/EN/UL62368-1 EMI - Conducted and radiated emission EN55032, class B (with the recommended EMI circuit) Electrostatic Discharge Immunity IEC 61000-4-2: Criteria A RF, Electromagnetic Field Immunity IEC 61000-4-3: Criteria A Electrical Fast Transient/Burst Immunity IEC 61000-4-4: Criteria A (with the recommended EMC circuit) Surge Immunity IEC 61000-4-5: Criteria A (with the recommended EMC circuit) RF, Conducted Disturbance Immunity IEC 61000-4-6: Criteria A Power frequency Magnetic Field Immunity IEC 61000-4-8: Criteria A Standards Pin Single 1 2 4 5 8 - V Input + V Input -V Output +V Output N.C. Dimensions Single output models 6.85 (0.27) Pin Out Specifications 0.25 (0.01) 5.24 (0.21) Approval 9.70 (0.38) 2.54 (0.10) 0.75 (0.03) 12.70 (0.50) 5 9.50 (0.37) 11.20 (0.44) 1 1.00 (0.04) All dimensions are in mm (inch) Pin Tolerance: ±0.25mm (0.01inch) Case Tolerance: ±0.50mm (0.02inch) 4 2 5.08 (0.20) 1.25 (0.05) 12.00 (0.47) 8 Solder pad dimensions www.aimtec.com F 051e R12.I Tel: +1 514 620 2722 2 of 6 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM1LO 1 Watt | DC-DC Converter Pin Out Specifications 1 2 4 5 7 10 - V Input + V Input Common -V Output +V Output N.C. Dual output models 0.25 (0.01) 5.42 (0.21) Dual 6.85 (0.27) Pin Dimensions 9.70 (0.38) 2.54 (0.10) 0.75 (0.03) 15.24 (0.60) 7 9.50 (0.37) 11.20 (0.44) 1 4 2 5 5.08 1.00 All dimensions are in mm (inch) Pin Tolerance: ±0.25mm (0.01inch) Case Tolerance: ±0.50mm (0.02inch) (0.20) (0.04) Conducted/Radiated Emmissons 1.25 (0.05) 12.00 (0.47) 10 Solder pad dimensions Single Output EMI Recommended Circuit (Class B) L +V output +V input C1 DC/DC Converter Load C1 22 µF / 10V -V input L 6.8 µH -V output EMC Recommended Circuit +Vout +Vin C1 330 µF / 50V DC/DC Converter + C1 TVS TVS 9V Load -Vin -Vout www.aimtec.com F 051e R12.I Tel: +1 514 620 2722 3 of 6 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM1LO 1 Watt | DC-DC Converter Input Reflected Ripple Current Test Circuit L1 12 µH Vin + Test Point Vo + + C1 47 µF Vin - Aimtec DC - DC Converter RL ( Full Load ) Vo - - * Tested at full load and nominal input C1 – ESR