AM20CW-2424D-NZ

Series AM20CW-NZ 20 Watt | DC-DC Converter FEATURES: • Wide 4:1 Input Voltage Range • High efficiency up to 90% • 1500 VDC Isolation • Over Current Protection • No load consumption ≤ 0.12W • • • • • Operating Temperature -40ºC to +85ºC Output Over Voltage protection Continuous Short Circuit Protection Input Under Voltage Protection Remote On/Off control Models Single output Model Input Voltage (V) Output Voltage (V) Output Current max (A) Isolation (VDC) Max Capacitive Load (uF) Efficiency Typ. (%) AM20CW-2403S-NZ 9-36 3.3 5 1500 10000 88 AM20CW-2405S-NZ 9-36 5 4 1500 10000 90 AM20CW-2412S-NZ 9-36 12 1.667 1500 1600 90 AM20CW-2415S-NZ 9-36 15 1.333 1500 1000 89 AM20CW-2424S-NZ 9-36 24 0.833 1500 500 91 AM20CW-4803S-NZ 18-75 3.3 5 1500 10000 88 AM20CW-4805S-NZ 18-75 5 4 1500 10000 90 AM20CW-4812S-NZ 18-75 12 1.667 1500 1600 91 AM20CW-4815S-NZ 18-75 15 1.333 1500 1000 91 AM20CW-4824S-NZ 18-75 24 0.833 1500 500 91 Add suffix “-ST” for optional screw terminal bottom plate or “-STD” for optional DIN Rail screw terminal bottom plate and reverse voltage protection. (Single output models only) *Add suffix “-K” for optional heatsink. (Single output models only) Models Dual output Model AM20CW-2405D-NZ AM20CW-2412D-NZ AM20CW-2415D-NZ AM20CW-2424D-NZ AM20CW-4805D-NZ AM20CW-4812D-NZ AM20CW-4815D-NZ AM20CW-4824D-NZ Input Voltage (V) Output Voltage (V) 9-36 9-36 9-36 9-36 18-75 18-75 18-75 18-75 Output Current max (A) Isolation (VDC) Max Capacitive Load (uF) Efficiency Typ. (%) ±2 ±0.833 ±0.667 ±0.417 ±2 ±0.833 ±0.667 ±0.417 1500 1500 1500 1500 1500 1500 1500 1500 2000 800 600 300 2000 800 600 300 87 90 90 89 86 90 90 90 ±5 ±12 ±15 ±24 ±5 ±12 ±15 ±24 NOTE: All specifications in this datasheet are measured at an ambient temperature of 25°C, humidity1000 2000 VDC 9 18 VDC 10 Isolation Specifications Parameters Tested I/O voltage Resistance Capacitance Maximum Units VDC MOhm pF Output Specifications Parameters Voltage accuracy Over voltage protection Over current protection Short circuit protection Short circuit restart Line voltage regulation Load voltage regulation Cross regulation Voltage adjustment Temperature coefficient Ripple & Noise Transient recovery time Transient recovery deviation Conditions Typical Maximum Units ±3 ±3 % Single output 0% to 100% load Dual output 5%-100% load ±1 ±1 110-160 150 Continuous Auto-Recovery Single output, Full load, LL to HL ±0.2 1st output ±0.2 Dual output, Full load, LL to HL 2nd output ±0.4 5% to 100% load ±0.5 50% at 1st output, 10-100% at 2nd output Single output 100% load Single output, 20MHz, 5-100% load 50 Dual output, 20MHz, 5-100% load 100 25% load step change 300 3.3/5VDC single output, 25% load step change ±5 ±5VDC dual output, 25% load step change ±3 Others, 25% load step change ±3 % of Vout % of Iout ±0.5 ±0.5 ±1 ±1 ±5 ±10 ±0.03 100 200 500 ±8 ±8 ±5 % of Vin % % %Vout %/oC mV p-p µs % General Specifications Parameters Switching frequency Operating temperature Storage temperature Maximum case temperature Cooling Humidity Case material Weight www.aimtec.com F 051e R3 REV:07/22/A Conditions Typical 3.3/5VDC single output, 100% load Others, 100% load 3.3/5VDC single output with derating curve Others with derating curve -55 to +125 Maximum 300 270 Units KHz -40 to +95 -40 to +105 oC oC 105 oC 95 % RH Free air convection Aluminum Alloy Pin mountable without heatsink Pin mountable with heatsink -ST option without heatsink -ST option with heatsink -STD option without heatsink -STD option with heatsink Tel: +1 514 620 2722 2 of 10 15 20 38 40 58 60 g Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM20CW-NZ 20 Watt | DC-DC Converter Pin mountable without heatsink 1.00 x 1.00 x 0.46 inches 25.40 x 25.40 x 11.70 mm Pin mountable with heatsink 1.00 x 1.00 x 0.64 inches 25.40 x 25.40 x 16.20 mm -ST option without heatsink 2.99 x 1.24 x 0.83 inches 76.00 x 31.50 x 21.20 mm -ST option with heatsink 2.99 x 1.24 x 0.99 inches 76.00 x 31.50 x 25.20 mm -STD option without heatsink 2.99 x 1.24 x 1.02 inches 76.00 x 31.50 x 25.80 mm -STD option with heatsink 2.99 x 1.24 x 1.17 inches 76.00 x 31.50 x 29.80 mm o >1,000,000 hours (MIL-HDBK -217F, Ground Benign, t=+25 C) oC 1.5mm from case for 10 sec 300 Dimensions (L x W x H) MTBF Maximum soldering temperature Environmental Specifications Parameters Test mode Acceleration Vibration 10-150Hz 5G, every axis tested Safety Specifications Parameters Approval cULus 62368-1 (with exception of the dual output models), CE Information technology Equipment IEC/EN/UL 62368-1 EMI - Conducted and radiated emission EN 55032, class B (with the recommended EMC circuit) Electrostatic Discharge Immunity IEC 61000-4-2, Contact ±4KV, Criteria B RF, Electromagnetic Field Immunity IEC 61000-4-3, 10V/m, Criteria A Electrical Fast Transient / Burst Immunity IEC 61000-4-4, ±2KV, Criteria B (with the recommended EMC circuit) Surge Immunity IEC 61000-4-5, ±2KV, Criteria B (with the recommended EMC circuit) RF, Conducted Disturbance Immunity IEC 61000-4-6, 3 Vrms, Criteria A Standards Pin Out Specifications Pin 1 2 3 4 5 6 Dual +V Input -V Input On/Off Control +V Output Common -V Output Pin Single +V Input -V Input On/Off Control +V Output Trim -V Output 1 2 3 4 5 6 Dimensions Bottom View 2.54 (0.10) Top View 25.40 (1.00) 10.16 (0.40) 10.16 (0.40) 5 20.32 (0.80) 25.40 (1.00) 4 2.54 (0.10) 6 +V Output Trim/ -V Output Common +V Input 1 Side View 2.54 (0.10) 10.16 (0.40) -V Input CTRL 2 3 5.08 7.62 (0.20) (0.30) 11.70 (0.46) Printed Face 2.54 (0.10) www.aimtec.com F 051e R3 REV:07/22/A ᴓ 1.00 (0.04) 4.10 (0.16) Notes: Dimensions mm (inch) Case Tolerance ±0.50 (±0.02) Pin Diameter 1.0 ± 0.10 (0.04 ± 0.004) Tel: +1 514 620 2722 3 of 10 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM20CW-NZ 20 Watt | DC-DC Converter Heatsink Option: AM20CW-NZ-K Bottom View 2.54 (0.10) Top View Pin 1 25.40 (1.00) 10.16 (0.40) 10.16 (0.40) 5 4 2.54 (0.10) 6 20.32 (0.80) 25.40 (1.00) +V Output Trim -V Output +V Input 2.54 (0.10) 1 11.7 (0.46) 16.2 (0.64) Side View 2.54 (0.10) 10.16 (0.40) -V Input CTRL 2 3 5.08 7.62 (0.20) (0.30) Notes: Dimensions mm (inch) Case Tolerance ±0.50 (±0.02) Pin Diameter 1.0 ± 0.10 (0.04 ± 0.004) 1.00 (0.04) Dimensions with -ST options Pin Out Specifications 76.00 (2.99) 61.60 (2.43) LED light 2 6 Top view 3 23.00 (0.91) 31.50 (1.24) 1 5 Pin Single 1 2 3 4 5 6 On/Off Control -Vin +Vin + Vout Trim - Vout 4 8.80 (0.35) Front view Dimensions: mm (inch) Case Tolerance:± 0.50 (0.02) Wire gauge: 24-12AWG 21.20 (0.84) Ø3.30 (Ø0.13) www.aimtec.com F 051e R3 REV:07/22/A Tel: +1 514 620 2722 4 of 10 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM20CW-NZ 20 Watt | DC-DC Converter Dimensions with -STD options Pin Out Specifications 76.00 (2.99) 61.60 (2.43) LED light 6 2 5 Top view 3 Single 1 2 3 4 5 6 On/Off Control -Vin +Vin + Vout Trim - Vout 23.00 (0.91) 31.50 (1.24) 1 Pin 9.80 (0.39) 4 25.80 (1.02) Front view Dimensions: mm (inch) Case Tolerance:± 1.00 (0.04) Wire gauge: 24-12AWG Dimensions with heatsink and -ST options Pin Out Specifications 76.00 (2.99) 61.60 (2.43) LED light 1 6 2 5 3 4 F 051e R3 REV:07/22/A On/Off Control -Vin +Vin + Vout Trim - Vout Dimensions: mm (inch) Case Tolerance:± 0.50 (0.02) Wire gauge: 24-12AWG 21.20 (0.84) Front view 8.80 (0.35) 25.20 (0.99) Ø3.30 (Ø0.13) www.aimtec.com Single 1 2 3 4 5 6 23.00 (0.91) 31.50 (1.24) Top view Pin Tel: +1 514 620 2722 5 of 10 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM20CW-NZ 20 Watt | DC-DC Converter Dimensions with heatsink and -STD options Pin Out Specifications 76.00 (2.99) 61.60 (2.43) LED light 2 5 3 4 Front view On/Off Control -Vin +Vin + Vout Trim - Vout 23.00 (0.91) 6 Single 1 2 3 4 5 6 25.80 (1.02) 9.80 (0.39) 1 29.80 (1.17) 31.50 (1.24) Top view Pin Dimensions: mm (inch) Case Tolerance:± 0.50 (0.02) Wire gauge: 24-12AWG Derating 3.3V & 5V single output models www.aimtec.com F 051e R3 REV:07/22/A Other single output models Tel: +1 514 620 2722 6 of 10 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM20CW-NZ 20 Watt | DC-DC Converter Free Air Convection Free Air Convection 71 ºC without heat sink 65 ºC without heat sink 70ºC with heat sink 80 Safe Operating Area 60 100 Output Power (%) Output Power (%) 100 40 -20 0 20 65 70 40 80 60 40 95 71 75 100 -40 -20 0 20 40 80 60 105 100 Ambient Temperature º C Ambient Temperature º C ±5V dual output model Other Dual output models Free Air Convection Free Air Convection 100 Output Power (%) 100 Output Power (%) Safe Operating Area 60 0 0 80 Safe Operating Area 60 40 80 Safe Operating Area 60 40 20 20 0 0 - 40 80 20 20 -40 75ºC with heat sink -20 0 20 40 85 80 60 105 100 - 40 -20 0 20 40 60 71 80 105 100 Ambient Temperature º C Ambient Temperature º C 24V output model Free Air Convection 71 ºC without heat sink 75oC with heat sink Output Power (%) 100 85oC with 100 LFM 80 89oC with 200 LFM Safe Operating Area 60 92oC with 400 LFM 40 20 0 71 75 -40 -20 0 20 40 60 85 92 89 80 105 100 Ambient Temperature º C www.aimtec.com F 051e R3 REV:07/22/A Tel: +1 514 620 2722 7 of 10 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM20CW-NZ 20 Watt | DC-DC Converter Typical Application Circuit Single + Vin + Vout + Vin +Vout + DC C1 - Vin DC - Vin Model + C1 C2 C2 - Vout Single 3.3/5/12/15V output Single 24V output 100µF 100µF 47µF - Vout Dual + Vin + Vout + Vin +Vout + + DC C1 - Vin - Vin 24V input dual output 48V input dual output C1 100µF 10 - 47µF C2 DC + Model Common C3 - Vout C2 10µF C3 10µF - Vout Recommended EMC Circuit CY1 1nF/2KV FUSE LDM + Vin + Vout + Vin + C0 + C1 DC C2 DC C3 +Vout + Cout - Vin - Vin - Vout - Vout CY2 1nF/2KV Model 24V input single output 48V input single output C0, C3 330µF/50V 330µF/100V C1, C2 4.7µF/50V 4.7µF/100V LDM 2.2µH/4A 2.2µH/2A Cout Refer to typical circuit C2 Model 24V input dual output 48V input dual output C0, C3 330µF/50V 330µF/100V C1, C2 4.7µF/50V 4.7µF/100V LDM 4.7µH Cout Refer to typical circuit C2 Trimming Output voltage can be externally trimmed by utilizing the methods as shown below www.aimtec.com F 051e R3 REV:07/22/A Tel: +1 514 620 2722 8 of 10 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM20CW-NZ 20 Watt | DC-DC Converter Fixed Resistor Variable Potentiometer Leave open if not used. www.aimtec.com F 051e R3 REV:07/22/A Tel: +1 514 620 2722 9 of 10 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM20CW-NZ 20 Watt | DC-DC Converter 3.3V Output Trim down % Vout (VDC) Rt down (KΩ) Trim up % Vout (VDC) Rt up (KΩ) 1 3.267 149.795 1 3.333 891.884 2 3.234 89.213 2 3.366 136.200 3 3.201 60.517 3 3.399 67.476 4 3.168 43.778 4 3.432 41.703 5 3.135 32.811 5 3.465 28.202 6 3.102 25.070 6 3.498 19.894 7 3.069 19.314 7 3.531 14.266 8 3.036 14.866 8 3.564 10.202 9 3.003 11.325 9 3.597 7.128 10 2.97 8.441 10 3.63 4.723 5V Output Trim down % Vout (VDC) Rt down (KΩ) Trim up % Vout (VDC) Rt up (KΩ) 2 3 4 5 6 7 8 9 10 4.95 89.996 1 5.05 238.676 4.9 47.446 2 5.1 81.473 4.85 29.793 3 5.15 46.044 4.8 20.131 4 5.2 30.398 4.75 14.036 5 5.25 21.581 4.7 9.840 6 5.3 15.923 4.65 6.775 7 5.35 11.985 4.6 4.439 8 5.4 9.085 4.55 2.598 9 5.45 6.861 4.5 1.111 10 5.5 5.101 12V Output Trim down % Vout (VDC) Rt down (KΩ) Trim up % Vout (VDC) Rt up (KΩ) 1 11.88 493.692 1 12.12 704.035 2 11.76 299.052 2 12.24 156.520 3 11.64 210.127 3 12.36 81.479 4 11.52 159.185 4 12.48 51.675 6 11.28 103.042 6 12.72 25.695 7 11.16 85.932 7 12.84 18.874 8 11.04 72.764 8 12.96 13.917 9 10.92 62.316 9 13.08 10.152 10 15V Output Trim down % Vout (VDC) Rt down (KΩ) Trim up % Vout (VDC) Rt up (KΩ) 1 14.85 632.483 1 15.15 1457.699 3 14.55 286.114 3 15.45 94.242 8 14.7 398.237 2 15.3 190.174 14.4 220.359 4 15.6 58.954 24V Output Trim down % Vout (VDC) Rt down (KΩ) Trim up % Vout (VDC) Rt up (KΩ) 1 23.76 1284.000 1 24.24 814.689 2 23.52 789.923 2 24.48 177.714 3 23.28 563.667 3 24.72 92.138 4 23.04 433.904 4 24.96 58.264 1 2 4 5 11.4 126.173 5 12.6 35.677 5 14.25 177.137 5 15.75 40.616 5 22.8 349.754 5 25.2 40.107 6 10.8 53.823 10 13.2 7.195 7 13.95 123.787 7 16.05 21.791 13.8 106.169 8 16.2 16.321 9 13.65 92.132 9 16.35 12.190 10 14.1 146.560 6 15.9 29.381 6 22.56 290.763 6 25.44 28.788 7 22.32 247.115 7 25.68 21.057 8 22.08 213.514 8 25.92 15.440 9 21.84 186.847 9 26.16 11.176 10 13.5 80.687 10 16.5 8.961 21.6 165.170 10 26.4 7.827 NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the date manufactured. 3. Mechanical drawings and specifications are for reference only. 4. All specifications are measured at an ambient temperature of 25°C, humidity