AM20CW-2424S-NZ

Series AM20CW-NZ 20 Watt | DC-DC Converter FEATURES: • Wide 4:1 Input Voltage Range • High efficiency up to 90% • 1500 VDC Isolation • Over Current Protection • No load consumption ≤ 0.12W • • • • • Operating Temperature -40ºC to +85ºC Output Over Voltage protection Continuous Short Circuit Protection Input Under Voltage Protection Remote On/Off control Models Single output Model AM20CW-2403S-NZ AM20CW-2405S-NZ AM20CW-2412S-NZ AM20CW-2415S-NZ AM20CW-2424S-NZ AM20CW-4803S-NZ AM20CW-4805S-NZ AM20CW-4812S-NZ AM20CW-4815S-NZ AM20CW-4824S-NZ Input Voltage (V) Output Voltage (V) Output Current max (A) Isolation (VDC) Max Capacitive Load (uF) Efficiency Typ. (%) 9-36 9-36 9-36 9-36 9-36 18-75 18-75 18-75 18-75 18-75 3.3 5 12 15 24 3.3 5 12 15 24 5 4 1.667 1.333 0.833 5 4 1.667 1.333 0.833 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 10000 10000 1600 1000 500 10000 10000 1600 1000 500 88 90 90 91 91 88 90 91 91 91 Input Voltage (V) Output Voltage (V) Output Current max (A) Isolation (VDC) Max Capacitive Load (uF) Efficiency Typ. (%) 1500 1500 1500 1500 1500 1500 1500 1500 2000 800 600 300 2000 800 600 300 87 90 90 89 86 90 90 90 Models Dual output Model AM20CW-2405D-NZ 9-36 ±5 AM20CW-2412D-NZ 9-36 ±12 AM20CW-2415D-NZ 9-36 ±15 AM20CW-2424D-NZ 9-36 ±24 AM20CW-4805D-NZ 18-75 ±5 AM20CW-4812D-NZ 18-75 ±12 AM20CW-4815D-NZ 18-75 ±15 AM20CW-4824D-NZ 18-75 ±24 *Add suffix “-K” for optional heatsink(Single output models only) ±2 ±0.833 ±0.667 ±0.417 ±2 ±0.833 ±0.667 ±0.417 NOTE: All specifications in this datasheet are measured at an ambient temperature of 25°C, humidity1000 2000 VDC 9 18 VDC 10 Isolation Specifications Parameters Tested I/O voltage Resistance Capacitance Maximum Units VDC MOhm pF Output Specifications Parameters Voltage accuracy Over voltage protection Over current protection Short Circuit protection Short circuit restart Line voltage regulation Load voltage regulation Cross Regulation Voltage adjustment Temperature coefficient Ripple & Noise Transient recovery time Transient recovery deviation Conditions Typical Maximum Units ±3 ±3 % Single output 0% to 100% load Dual output 5%-100% load ±1 ±1 110-160 150 Continuous Auto-Recovery Single output, Full load, LL to HL ±0.2 1st output ±0.2 Dual output, Full load, LL to HL 2nd output ±0.4 5% to 100% load ±0.5 50% at 1st output, 10-100% at 2nd output Single output 100% load Single output, 20MHz, 5-100% load 50 Dual output, 20MHz, 5-100% load 100 25% load step change 300 3.3/5VDC single output, 25% load step change ±5 ±5VDC dual output, 25% load step change ±3 Others, 25% load step change ±3 % of Vout % of Iout ±0.5 ±0.5 ±1 ±1 ±5 ±10 ±0.03 100 200 500 ±8 ±8 ±5 % of Vin % % %Vout %/oC mV p-p µs % General Specifications Parameters Switching frequency Operating temperature Storage temperature Maximum case temperature Cooling Humidity Case material Weight Dimensions (L x W x H) MTBF www.aimtec.com F 051e R3 REV:04/22/A Conditions Typical 3.3/5VDC single output, 100% load Others, 100% load 3.3/5VDC single output with derating curve Others with derating curve -55 to +125 Maximum 300 270 Units KHz -40 to +95 -40 to +105 105 o C o C C o Free air convection 95 % RH Aluminum Alloy Pin mountable: 15 g With optional -K Pin mountable: 20 Pin mountable: 1.00 x 1.00 x 0.46 inches 25.40 x 25.40 x 11.70 mm With optional -K Pin mountable: 1.00 x 1.00 x 0.64 inches 25.40 x 25.40 x 16.20 mm o >1,000,000 hours (MIL-HDBK -217F, Ground Benign, t=+25 C) Tel: +1 514 620 2722 2 of 7 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM20CW-NZ 20 Watt | DC-DC Converter Maximum soldering temperature 1.5mm from case for 10 sec 300 o C Environmental Specifications Parameters Test mode Acceleration Vibration 10-150Hz 5G, every axis tested Safety Specifications Parameters Approval cULus(with exception of the dual output models), CE Information technology Equipment IEC/EN/UL 62368-1 EMI - Conducted and radiated emission EN 55032, class B (with the recommended EMC circuit) Electrostatic Discharge Immunity IEC 61000-4-2, Contact ±4KV, Criteria B RF, Electromagnetic Field Immunity IEC 61000-4-3, 10V/m, Criteria A Electrical Fast Transient / Burst Immunity IEC 61000-4-4, ±2KV, Criteria B (with the recommended EMC circuit) Surge Immunity IEC 61000-4-5, ±2KV, Criteria B (with the recommended EMC circuit) RF, Conducted Disturbance Immunity IEC 61000-4-6, 3 Vrms, Criteria A Standards Pin Out Specifications Pin 1 2 3 4 5 6 Dual +V Input -V Input On/Off Control +V Output Common -V Output Pin Single +V Input -V Input On/Off Control +V Output Trim -V Output 1 2 3 4 5 6 Dimensions Bottom View Top View 2.54 (0.10) 10.16 (0.40) 25.40 (1.00) 10.16 (0.40) 5 20.32 (0.80) 25.40 (1.00) 4 2.54 (0.10) 6 +V Output Trim/ -V Output Common +V -V Input Input CTRL 1 Side View 2.54 (0.10) 10.16 (0.40) 2 3 5.08 7.62 (0.20) (0.30) 2.54 (0.10) www.aimtec.com F 051e R3 REV:04/22/A ᴓ 1.00 (0.39) 4.10 (0.16) 11.70 (0.46) Printed Face Notes: Dimensions mm (inch) Case Tolerance ±0.50 (±0.02) Pin Diameter 1.0 ± 0.10 (0.04 ± 0.004) Tel: +1 514 620 2722 3 of 7 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM20CW-NZ 20 Watt | DC-DC Converter Heatsink Option: AM20CW-NZ-K Bottom View Top View 10.16 (0.40) 2.54 (0.10) Pin 1 25.40 (1.00) 10.16 (0.40) 5 4 2.54 (0.10) 6 20.32 (0.80) 25.40 (1.00) +V Output Trim -V Output +V Input 1 2.54 (0.10) 10.16 (0.40) 2 3 5.08 7.62 (0.20) (0.30) Notes: 11.7 (0.46) 16.2 (0.64) Side View -V Input CTRL 2.54 (0.10) Dimensions mm (inch) Case Tolerance ±0.50 (±0.02) Pin Diameter 1.0 ± 0.10 (0.04 ± 0.004) 1.00 (0.39) Derating 3.3V & 5V single output models Other single output models Free Air Convection Free Air Convection 65 ºC without heat sink 70ºC with heat sink 80 Safe Operating Area 60 100 Output Power (%) Output Power (%) 100 40 20 75ºC with heat sink 80 Safe Operating Area 60 40 20 0 -40 71 ºC without heat sink -20 0 20 40 65 70 60 80 95 100 0 -40 Ambient Temperature º C www.aimtec.com F 051e R3 REV:04/22/A -20 0 20 40 60 71 75 80 105 100 Ambient Temperature º C Tel: +1 514 620 2722 4 of 7 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM20CW-NZ 20 Watt | DC-DC Converter ±5V dual output model Other Dual output models Free Air Convection Free Air Convection 100 Output Power (%) Output Power (%) 100 80 Safe Operating Area 60 40 20 80 Safe Operating Area 60 40 20 0 -20 - 40 0 20 40 85 80 60 0 105 100 -20 - 40 Ambient Temperature º C 0 20 40 60 71 80 105 100 Ambient Temperature º C 24V output model Free Air Convection 71 ºC without heat sink 75oC with heat sink Output Power (%) 100 85oC with 100 LFM 80 89oC with 200 LFM Safe Operating Area 60 92oC with 400 LFM 40 20 0 -20 -40 0 20 40 60 71 75 85 92 89 80 105 100 Ambient Temperature º C Typical Application Circuit Single + Vin + Vout + Vin + C1 - Vin DC DC - Vin +Vout + C1 C2 C2 - Vout + Vin + C1 - Vin www.aimtec.com F 051e R3 REV:04/22/A DC - Vin + Vout DC - Vout Single 3.3/5/12/15V output Single 24V output 100µF 100µF 47µF - Vout Dual + Vin Model + + +Vout C2 Common C3 Model 24V input dual output 48V input dual output C1 100µF 10 - 47µF C2 10µF C3 10µF - Vout Tel: +1 514 620 2722 5 of 7 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM20CW-NZ 20 Watt | DC-DC Converter Recommended EMC Circuit CY1 1nF/2KV FUSE LDM + Vin + Vout + Vin + C0 + C1 C2 DC C3 DC +Vout + Cout - Vin - Vin - Vout - Vout CY2 1nF/2KV Model 24V input single output 48V input single output C0, C3 330µF/50V 330µF/100V C1, C2 4.7µF/50V 4.7µF/100V LDM 2.2µH/4A 2.2µH/2A Cout Refer to typical circuit C2 Model 24V input dual output 48V input dual output C0, C3 330µF/50V 330µF/100V C1, C2 4.7µF/50V 4.7µF/100V LDM 4.7µH Cout Refer to typical circuit C2 Trimming Output voltage can be externally trimmed by utilizing the methods as shown below Fixed Resistor Variable Potentiometer Leave open if not used. www.aimtec.com F 051e R3 REV:04/22/A Tel: +1 514 620 2722 6 of 7 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM20CW-NZ 20 Watt | DC-DC Converter 3.3V Output Trim down % Vout (VDC) Rt down (KΩ) Trim up % Vout (VDC) Rt up (KΩ) 1 3.267 138.598 1 3.333 1795.815 2 3.234 83.989 2 3.366 149.446 3 3.201 57.383 3 3.399 71.134 4 3.168 41.637 4 3.432 43.348 5 3.135 31.229 5 3.465 29.116 6 3.102 23.837 6 3.498 20.466 7 3.069 18.316 7 3.531 14.652 8 3.036 14.037 8 3.564 10.475 9 3.003 10.621 9 3.597 7.330 10 2.97 7.833 10 3.63 4.876 5V Output Trim down % Vout (VDC) Rt down (KΩ) Trim up % Vout (VDC) Rt up (KΩ) 1 4.95 89.996 1 5.05 238.676 2 4.9 47.446 2 5.1 81.473 3 4.85 29.793 3 5.15 46.044 4 4.8 20.131 4 5.2 30.398 5 4.75 14.036 5 5.25 21.581 6 4.7 9.840 6 5.3 15.923 7 4.65 6.775 7 5.35 11.985 8 4.6 4.439 8 5.4 9.085 9 4.55 2.598 9 5.45 6.861 10 4.5 1.111 10 5.5 5.101 12V Output Trim down % Vout (VDC) Rt down (KΩ) Trim up % Vout (VDC) Rt up (KΩ) 1 11.88 493.692 1 12.12 704.035 2 11.76 299.052 2 12.24 156.520 3 11.64 210.127 3 12.36 81.479 4 11.52 159.185 4 12.48 51.675 5 11.4 126.173 5 12.6 35.677 6 11.28 103.042 6 12.72 25.695 7 11.16 85.932 7 12.84 18.874 8 11.04 72.764 8 12.96 13.917 9 10.92 62.316 9 13.08 10.152 10 10.8 53.823 10 13.2 7.195 15V Output Trim down % Vout (VDC) Rt down (KΩ) Trim up % Vout (VDC) Rt up (KΩ) 1 14.85 632.483 1 15.15 1457.699 2 14.7 398.237 2 15.3 190.174 3 14.55 286.114 3 15.45 94.242 4 14.4 220.359 4 15.6 58.954 5 14.25 177.137 5 15.75 40.616 6 14.1 146.560 6 15.9 29.381 7 13.95 123.787 7 16.05 21.791 8 13.8 106.169 8 16.2 16.321 9 13.65 92.132 9 16.35 12.190 10 13.5 80.687 10 16.5 8.961 24V Output Trim down % Vout (VDC) Rt down (KΩ) Trim up % Vout (VDC) Rt up (KΩ) 1 23.76 1284.000 1 24.24 814.689 2 23.52 789.923 2 24.48 177.714 3 23.28 563.667 3 24.72 92.138 4 23.04 433.904 4 24.96 58.264 5 22.8 349.754 5 25.2 40.107 6 22.56 290.763 6 25.44 28.788 7 22.32 247.115 7 25.68 21.057 8 22.08 213.514 8 25.92 15.440 9 21.84 186.847 9 26.16 11.176 10 21.6 165.170 10 26.4 7.827 NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the date manufactured. 3. Mechanical drawings and specifications are for reference only. 4. All specifications are measured at an ambient temperature of 25°C, humidity