AM20EW-2424S-NZ

Series AM20EW-NZ 20 Watt | DC-DC Converter FEATURES:50 • • • • • Efficiency up to 90% Ultra-wide 4:1 Input range No-load consumption ≤0.15W Over Current protection Input under voltage lockout • • • • • On/Off Remote Control Over Voltage Protection I/Output Isolation 1500, 2250 & 3000VDC Operating Temperature: -40oC to +85oC Continuous Short Circuit protection Models Single output Input Voltage (V) Max Input Current Full/No load (mA) Output Voltage (V) Output Current max (mA) Isolation (VDC) Max Capacitive Load (uF) Efficiency (%) AM20EW-2403S-NZ AM20EW-2405S-NZ AM20EW-2409S-NZ AM20EW-2412S-NZ AM20EW-2415S-NZ AM20EW-2424S-NZ AM20EW-4803S-NZ AM20EW-4805S-NZ AM20EW-4809S-NZ AM20EW-4812S-NZ AM20EW-4815S-NZ AM20EW-4824S-NZ AM20EW-11005S-NZ ⨳ AM20EW-11012S-NZ ⨳ AM20EW-11015S-NZ ⨳ AM20EW-11024S-NZ ⨳ 9-36 9-36 9-36 9-36 9-36 9-36 18-75 18-75 18-75 18-75 18-75 18-75 40-160 40-160 40-160 40-160 818/45 993/45 941/10 941/10 941/10 941/10 409/25 497/25 485/9 485/9 485/9 485/9 212/20 212/20 212/20 212/20 3.3 5 9 12 15 24 3.3 5 9 12 15 24 5 12 15 24 5000 4000 2222 1667 1333 834 5000 4000 2222 1667 1333 834 4000 1667 1333 833 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 10000 10000 4700 1600 1000 500 10000 10000 4700 1600 1000 500 4020 1600 1000 470 86 90 89 89 90 90 86 90 89 89 90 90 89 88 88 88 AM20EW-11003SH22-NZ AM20EW-11005SH22-NZ AM20EW-11012SH22-NZ AM20EW-11015SH22-NZ AM20EW-11024SH22-NZ 40-160 40-160 40-160 40-160 40-160 188/20 222/20 219/8 219/8 219/8 3.3 5 12 15 24 5000 4000 1667 1333 833 2250 2250 2250 2250 2250 10000 10000 1600 1000 470 82 84 85 86 86 AM20EW-2403SH30-NZ AM20EW-2405SH30-NZ AM20EW-2409SH30-NZ AM20EW-2412SH30-NZ AM20EW-2415SH30-NZ AM20EW-2418SH30-NZ AM20EW-2424SH30-NZ AM20EW-4803SH30-NZ AM20EW-4805SH30-NZ AM20EW-4812SH30-NZ AM20EW-4815SH30-NZ AM20EW-4824SH30-NZ 9-36 9-36 9-36 9-36 9-36 9-36 9-36 18-75 18-75 18-75 18-75 18-75 818/45 958/45 967/12 967/12 967/12 969/20 967/12 409/25 484/25 484/8 484/8 484/8 3.3 5 9 12 15 18 24 3.3 5 12 15 24 5000 4000 2222 1667 1333 1111 834 5000 4000 1667 1333 834 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 10000 10000 4700 1600 1000 680 500 10000 10000 1600 1000 500 86 89 88 88 89 89 89 86 88 88 89 89 Input Voltage (V) Max Input current Full/No load (mA) Output Voltage (V) Output Current max (mA) Isolation (VDC) Max Capacitive Load(uF) 9-36 9-36 9-36 9-36 18-75 993/45 941/10 941/10 941/10 497/25 ±5 ±9 ±12 ±15 ±5 ±2000 ±1111 ±834 ±667 ±2000 1500 1500 1500 1500 1500 ±4800 ±1000 ±800 ±625 ±4800 Model Models Dual output Model AM20EW-2405D-NZ AM20EW-2409D-NZ AM20EW-2412D-NZ AM20EW-2415D-NZ AM20EW-4805D-NZ www.aimtec.com F 051e R13.H REV: 04/22/A Tel: +1 514 620 2722 1 of 15 Efficiency (Typ.) (%) 86 88 88 88 86 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM20EW-NZ 20 Watt | DC-DC Converter AM20EW-4812D-NZ AM20EW-4815D-NZ 18-75 18-75 485/9 485/9 ±12 ±15 ±834 ±667 1500 1500 ±800 ±625 88 89 AM20EW-11012DH30-NZ 40-160 217/8 ±12 ±833 3000 ±680 85 AM20EW-11015DH30-NZ 40-160 217/8 ±15 ±667 3000 ±470 86 AM20EW-11024DH30-NZ 40-160 217/8 ±24 ±417 3000 ±220 86 Add suffix “-K” for optional heatsink for metal cased models only. *Add suffix “-ST” for optional screw terminal bottom plate or “-STD” for optional DIN Rail screw terminal bottom plate and reverse voltage protection. Their minimum input voltage and startup voltage have to be increased by 1V. **Add suffix “-K-ST” for optional heatsink and screw terminal bottom plate(for metal cased models only) or “-K-STD” for optional heatsink and DIN Rail screw terminal bottom plate and reverse voltage protection(for metal cased models only). ***Models marked with ⨳ are not recommended for new designs. The optional "-K", "-ST", "-STD", "-K-ST" or "-K-STD" packages for models marked with ⨳ have been obsoleted. NOTE: All specifications in this datasheet are measured at an ambient temperature of 25°C, humidity1000 2000 2200 500 Units VDC VDC MOhm pF Output Specifications Parameters Voltage accuracy Balanced load Over voltage protection Over current protection Short Circuit protection Short circuit restart Line voltage regulation (single) Line voltage regulation (dual) Load voltage regulation (single) Load voltage regulation (dual) www.aimtec.com F 051e R13.H REV: 04/22/A Conditions 110Vin, 3000V isolation, positive output Others Typical ±1 ±1 ±0.5 Zener Diode Clamp 110 120 Continuous, hiccup Auto-Recovery Full load, LL-HL ±0.2 110Vin, 3000V isolation, positive output ±0.2 Full load, LL-HL ±0.5 5% to 100% load for 1500VDC models ±0.5 & 0% to 100% load for others 110Vin, 3000V isolation, positive output ±0.5 5% to 100% load ±0.5 Tel: +1 514 620 2722 2 of 15 Maximum ±2 ±3 ±1.5 160 210 Units % % % % of Io ±0.5 ±0.5 ±1 % of Vin ±1 % ±1 ±1.5 % % of Vin Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM20EW-NZ 20 Watt | DC-DC Converter Cross regulation Temperature coefficient Ripple & Noise Voltage adjustment range Transient recovery time Transient recovery deviation 50% 1st load, 10-100% 2nd load 20MHz Bandwidth, 5% to 100% load 25% load step change, 2250V/3000V isolation 25% load step change, others 25% load step change: 3.3, 5, ±5Vout 25% load step change: others ±5 ±3 ±5 ±0.03 100 ±10 500 800 ±8 ±5 % %/oC mV p-p % µS % General Specifications Parameters Switching frequency Operating temperature Storage temperature Maximum case temperature Cooling Humidity Case material Dimensions (L x W x H) Weight MTBF Maximum soldering temperature Conditions Typical 100% load, 24 & 48 Vin 100% load, 110Vin See derating curve 270 300 Maximum Units KHz o -40 to +85 C C o C o -55 to +125 105 Free air convection 95 % RH Plastic (UL94-V0) Aluminum Alloy 2 x 1 x 0.47 inches 50.8 x 25.4 x 11.8 mm 2.03 x 1.04 x 0.47 inches 51.5 x 26.5 x 12 mm See dimensions drawing 28 (110Vin, 1500VDC Isolated models) Pin mountable without heatsink 26 (Other metal case models) 24 (3000VDC Isolated models) 36 (110Vin, 1500VDC Isolated models) Pin mountable with heatsink 34 (Other metal case models) 32 (3000VDC Isolated models) 50 (110Vin, 1500VDC Isolated models) -ST option without heatsink 48 (Other metal case models) 46 (3000VDC Isolated models) g 58 (110Vin, 1500VDC Isolated models) -ST option with heatsink 56 (Other metal case models) 54 (3000VDC Isolated models) 70 (110Vin, 1500VDC Isolated models) -STD option without heatsink 68 (Other metal case models) 66 (3000VDC Isolated models) 78 (110Vin, 1500VDC Isolated models) -STD option with heatsink 76 (Other metal case models) 74 (3000VDC Isolated models) o >1,000,000 hours (MIL-HDBK -217F, Ground Benign, t=+25 C) o 1.5mm from case for 10 sec 300 C 24/48Vin, 3000VDC models Other models Aluminium case Plastic case Optional packages Environment Specification Test Parameters Test mode Acceleration Vibration Vibration (110 Vin/2250VDC isolation) Conditions 10-55Hz 10g, 30min, every axis tested IEC61373 car body 1 B mold Safety Specifications Parameters Agency approvals Standards www.aimtec.com F 051e R13.H REV: 04/22/A cULus (with exception of AM20EW-2418SH30-NZ & 110Vin models), CE (110Vin models only) EN 55032, Class B, with EMC recommended circuit EN 50121-3-2, 150kHz-500kHz 99dBuV, 30MHz-230MHz 40dBuV/m at 10m (110Vin, 2250VDC models approved with recommended cirucit) (24/48Vin, 1500VDC & 110Vin, 3000 VDC models meet with recommended cirucit) EN 55016-2-1, 500kHz-30MHz 93dBuV, 230MHz-1GHz 47dBuV/m at 10m (110Vin, 2250VDC models approved with recommended cirucit) (24/48Vin, 1500VDC & 110Vin, 3000 VDC models meet with recommended cirucit) Information technology Equipment IEC/UL 60950-1 Tel: +1 514 620 2722 3 of 15 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM20EW-NZ 20 Watt | DC-DC Converter Railway application Electrostatic Discharge Immunity RF, Electromagnetic Field Immunity Electrical Fast Transient / Burst Immunity Surge Immunity RF, Conducted Disturbance Immunity Voltage dips, Short Interruptions & Voltage variations Immunity EN50155 (110Vin, 2250VDC models compliant) (24/48Vin, 1500VDC and 110Vin, 3000 VDC models meet) IEC 61000-4-2, Contact ±6KV (110Vin 2250/3000VDC Isolation), Contact ±4KV (Others), Criteria B EN50121-3-2, Contact ±6KV/Air ±8KV(24/48Vin 1500VDC and 110Vin 2250/3000VDC Isolation), Criteria B IEC 61000-4-3, 20V/m(110Vin 3000VDC isolation), 10V/m(Others), Criteria A EN50121-3-2, 20V/m (24/48Vin 1500VDC & 110Vin 2250/3000VDC Isolation), Criteria A IEC 61000-4-4, ±4KV (110Vin 2250/3000 VDC Isolation), ±2KV (Others), Criteria B, with external filter EN50121-3-2, ±2KV (24/48Vin 1500VDC & 110Vin 2250/3000VDC Isolation), Criteria A IEC 61000-4-5, ±2KV, Criteria B, with external filter EN50121-3-2, L-L ±1KV (24/48Vin 1500VDC & 110Vin 2250/3000VDC Isolation), Criteria B IEC 61000-4-6, 10 Vrms (2250/3000 VDC Isolated models), 3Vrms (Others), Criteria A EN50121-3-2, 0.15MHz ~ 80MHz, 10 Vrms (24/48Vin 1500VDC & 110Vin 2250/3000VDC Isolation), Criteria B IEC 61000-4-29, 0-70%, Criteria B Pin Out Specifications 2 1 5 4 20.32 (0.80) 10.16 (0.40) Bottom View 10.16 (0.40) 3 15.24 (0.60) 2.54 (0.10) 7.62 5.08 (0.30)(0.20) 10.16 (0.40) 6 15.24 (0.60) Notes: All dimensions are typical in millimeters (inches). Pin diameter Tolerance ±0.10 (±0.014) Case Tolerance ±0.50 (±0.02) 4.10 (0.16) DIA 1.00 (0.04) 2.54 (0.10) 50.80 (2.00) Dual On/Off Control -Vin +Vin -Vout Common +Vout 25.40 (1.00) Single On/Off Control -Vin +Vin -Vout Trim +Vout 11.80 (0.47) Pin 1 2 3 4 5 6 Dimensions metal case Dimensions metal case for 110Vin 3000V isolation dual output models Bottom View 5 1 4 10.16 (0.40) 5.08 10.16 5.08 (0.20) (0.40) (0.20) 2.54 (0.10) F 051e R13.H REV: 04/22/A 4.10 (0.16) 25.40 (1.00) 11.80 (0.47) www.aimtec.com 2 10.16 (0.40) 6 3 DIA 1.00 (0.04) 2.54 (0.10) 45.72 (1.80) 2.54 (0.10) 50.80 (2.00) Notes: All dimensions are typical in millimeters (inches). Pin diameter Tolerance ±0.10 (±0.014) Case Tolerance ±0.50 (±0.02) Tel: +1 514 620 2722 4 of 15 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM20EW-NZ 20 Watt | DC-DC Converter 2.54 (0.10) Dimensions plastic case 51.50 (2.03) 2 1 15.24 (0.60) 10.16 (0.40) 4 15.24 (0.60) 20.32 (0.80) 12.00 (0.47) Notes: All dimensions are typical in millimeters (inches). Pin diameter Tolerance ±0.10 (±0.004) Case Tolerance ±0.50 (±0.02) 4.10 (0.16) DIA 1.00 (0.04) DIA 1.00 (0.04) 15.54 (0.61) 4 20.32 (0.80) 15.54 (0.61) Notes: All dimensions are typical in millimeters (inches). Pin diameter Tolerance: ±0.10 (±0.004) Case Tolerance: ±0.50 (±0.02) www.aimtec.com 4.10 (0.16) 6 3 2 Bottom View 5 1 4 2.94 (0.12) 1 5 5.08 5.08 (0.20) 10.16 (0.20) (0.40) Bottom View 2.94 (0.12) 2 10.16 (0.40) 3 10.16 (0.40) 5.08 7.62 (0.20) 10.56 (0.30) (0.42) 6 2.54 (0.10) 51.4 (2.02) 45.72 (1.80) 10.16 (0.40) 2.94 (0.12) DIA 1.00 (0.04) Side view 10.16 (0.40) Side view 16.50 (0.65) Optional -K heatsink for 110V 3000V isolation dual output models 4.10 (0.16) 16.50 (0.65) Optional -K heatsink F 051e R13.H REV: 04/22/A 5 Bottom View 10.16 (0.40) 3 2.54 (0.10) 26.50 (1.04) 5.08 7.62 (0.20) (0.30) 10.16 (0.40) 6 Notes: All dimensions are typical in millimeters (inches). Pin diameter Tolerance: ±0.10 (±0.004) Case Tolerance: ±0.50 (±0.02) Tel: +1 514 620 2722 5 of 15 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM20EW-NZ 20 Watt | DC-DC Converter Dimensions with -ST options Pin Out Specifications 76.00 (2.99) 61.60 (2.43) LED light 6 Top view 2 3 23.00 (0.91) 31.50 (1.24) 1 5 Pin Single Single 1 2 3 4 5 6 On/Off Control -Vin +Vin + Vout Trim - Vout On/Off Control -Vin +Vin + Vout Common - Vout 4 8.80 (0.35) Side view 21.20 (0.84) Dimensions: mm (inch) Case Tolerance:± 0.50 (0.02) Wire gauge: 24-12AWG Dimensions with -STD options Pin Out Specifications 76.00 (2.99) 61.60 (2.43) LED light 6 Top view 2 3 5 23.00 (0.91) 31.50 (1.24) 1 Pin Single Single 1 2 3 4 5 6 On/Off Control -Vin +Vin + Vout Trim - Vout On/Off Control -Vin +Vin + Vout Common - Vout 4 25.80 (1.02) Side view 9.80 (0.39) Ø3.30 Ø0.13 Dimensions: mm (inch) Case Tolerance:± 1.00 (0.04) Wire gauge: 24-12AWG www.aimtec.com F 051e R13.H REV: 04/22/A Tel: +1 514 620 2722 6 of 15 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM20EW-NZ 20 Watt | DC-DC Converter Dimensions with heatsink and -ST options Pin Out Specifications 76.00 (2.99) 61.60 (2.43) LED light 6 Top view 2 3 23.00 (0.91) 31.50 (1.24) 1 5 Pin Single Single 1 2 3 4 5 6 On/Off Control -Vin +Vin + Vout Trim - Vout On/Off Control -Vin +Vin + Vout Common - Vout 4 Dimensions: mm (inch) Case Tolerance:± 0.50 (0.02) Wire gauge: 24-12AWG 21.20 (0.84) 8.80 (0.35) 25.30 (1.00) Side view Dimensions with heatsink and -STD options Pin Out Specifications 76.00 (2.99) 61.60 (2.43) LED light 6 Top view 2 3 5 Single Single 1 2 3 4 5 6 On/Off Control -Vin +Vin + Vout Trim - Vout On/Off Control -Vin +Vin + Vout Common - Vout 23.00 (0.91) 31.50 (1.24) 1 Pin 4 25.80 (1.02) 29.90 (1.18) Side view 9.80 (0.39) Ø3.30 Ø0.13 Dimensions: mm (inch) Case Tolerance:± 0.50 (0.02) Wire gauge: 24-12AWG www.aimtec.com F 051e R13.H REV: 04/22/A Tel: +1 514 620 2722 7 of 15 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM20EW-NZ 20 Watt | DC-DC Converter Trimming Output voltage can be externally trimmed by utilizing the methods as shown below Fixed Resistor Variable Potentiometer Leave open if not used. AM20EW-xx03S-NZ, xx=24 or 48 Trim down % Vout (VDC) Rt down (KΩ) Trim up % Vout (VDC) Rt up (KΩ) 1 3.27 144.368 1 3.33 1283.554 2 3.23 87.896 2 3.37 146.232 3 3.2 60.680 3 3.4 72.087 4 3.17 44.663 4 3.43 45.176 5 3.14 34.112 5 3.47 31.267 6 3.1 26.636 6 3.5 22.770 7 3.07 21.063 7 3.53 17.042 8 3.04 16.748 8 3.56 12.918 9 3 13.308 9 3.6 9.808 10 2.97 10.502 10 3.63 7.378 2 3.234 90.296 2 3.366 148.632 3 3.201 63.080 3 3.399 74.487 4 3.168 47.063 4 3.432 47.576 5 3.135 36.512 5 3.465 33.667 6 3.102 29.036 6 3.498 25.170 7 3.069 23.463 7 3.531 19.442 8 3.036 19.148 8 3.564 15.318 9 3.003 15.708 9 3.597 12.208 10 2.97 12.902 10 3.63 9.778 AM20EW-11003SH22-NZ Trim down % Vout (VDC) Rt down (KΩ) Trim up % Vout (VDC) Rt up (KΩ) 1 3.267 146.768 1 3.333 1285.954 AM20EW-xx05S-NZ, xx=24 or 48 Trim down % 1 2 3 4 5 6 7 8 9 10 Vout (VDC) Rt down (KΩ) Trim up % 4.95 105.18 1 4.9 52.153 2 4.85 31.996 3 4.8 21.377 4 4.75 14.822 5 4.7 10.372 6 4.65 7.154 7 4.6 4.719 8 4.55 2.811 9 4.5 1.276 10 Vout (VDC) 5.05 5.1 5.15 5.2 5.25 5.3 5.35 5.4 5.45 5.5 Rt up (KΩ) 176.356 71.279 41.973 28.2 20.197 14.967 11.281 8.543 6.43 4.749 AM20EW-11005S-NZ Trim down % 1 2 3 4 5 6 7 8 9 10 Vout (VDC) Rt down (KΩ) Trim up % 4.95 96.08 1 4.9 49.349 2 4.85 30.67 3 4.8 20.616 4 4.75 14.333 5 4.7 10.034 6 4.65 6.909 7 4.6 4.533 8 4.55 2.667 9 4.5 1.162 10 5.05 205.698 5.1 76.406 5.15 44.023 5.2 29.296 5.25 20.879 5.3 15.431 5.35 11.617 5.4 8.798 5.45 6.63 5.5 4.91 Vout (VDC) Rt up (KΩ) www.aimtec.com F 051e R13.H REV: 04/22/A Tel: +1 514 620 2722 8 of 15 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM20EW-NZ 20 Watt | DC-DC Converter AM20EW-11005SH22-NZ Trim down % Vout (VDC) Rt down (KΩ) Trim up % Vout (VDC) Rt up (KΩ) 1 4.95 105.181 1 5.05 176.356 2 4.9 52.154 2 5.1 71.279 3 4.85 31.997 3 5.15 41.974 4 4.8 21.378 4 5.2 28.2 5 4.75 14.823 5 5.25 20.198 6 4.7 10.373 6 5.3 14.967 7 4.65 7.155 7 5.35 11.281 8 4.6 4.719 8 5.4 8.544 9 4.55 2.811 9 5.45 6.43 10 4.5 1.277 10 5.5 4.749 3 8.73 139.156 3 9.27 64.147 4 8.64 102.145 4 9.36 42.357 5 8.55 78.924 5 9.45 29.974 6 8.46 62.996 6 9.54 21.989 7 8.37 51.392 7 9.63 16.412 8 8.28 42.562 8 9.72 12.296 9 8.19 35.616 9 9.81 9.134 10 8.1 30.011 10 9.9 6.628 AM20EW-xx09S-NZ, xx=24 or 48 Trim down % Vout (VDC) Rt down (KΩ) Trim up % Vout (VDC) Rt up (KΩ) 1 8.91 375.532 1 9.09 314.531 2 8.82 207.429 2 9.18 112.638 AM20EW-xx12S-NZ, xx=24 or 48 Trim down % Vout (VDC) Rt down (KΩ) 1 11.88 496.091 2 11.76 301.451 3 11.64 212.527 4 11.52 161.585 5 11.4 128.573 6 11.28 105.441 7 11.16 88.332 8 11.04 75.163 9 10.92 64.715 10 10.8 56.223 Trim up % Vout (VDC) Rt up (KΩ) 1 12.12 706.435 2 12.24 158.92 3 12.36 83.878 4 12.48 54.074 5 12.6 38.076 6 12.72 28.095 7 12.84 21.274 8 12.96 16.316 9 13.08 12.551 10 13.2 9.594 AM20EW-11012S-NZ Trim down % Vout (VDC) 1 11.88 2 11.76 3 11.64 4 11.52 5 11.4 6 11.28 7 11.16 8 11.04 9 10.92 10 10.8 Rt down (KΩ) Trim up % Vout (VDC) Rt up (KΩ) 505.529 1 12.12 614.769 303.041 2 12.24 150.097 211.851 3 12.36 78.994 159.978 4 12.48 50.198 126.504 5 12.6 34.607 103.114 6 12.72 24.832 85.849 7 12.84 18.13 72.581 8 12.96 13.249 62.066 9 13.08 9.536 53.527 10 13.2 6.616 2 3 4 5 6 7 8 9 10 AM20EW-11012SH22-NZ Trim down % Vout (VDC) 1 11.88 11.76 11.64 11.52 11.4 11.28 11.16 11.04 10.92 10.8 Rt down (KΩ) Trim up % Vout (VDC) 496.092 1 12.12 301.452 2 12.24 212.527 3 12.36 161.585 4 12.48 128.573 5 12.6 105.442 6 12.72 88.332 7 12.84 75.164 8 12.96 64.716 9 13.08 56.223 10 13.2 Rt up (KΩ) 706.435 158.92 83.879 54.075 38.077 28.095 21.274 16.317 12.552 9.595 AM20EW-xx15S-NZ, xx=24 or 48 Trim down % 1 2 3 4 5 6 7 8 9 10 Vout (VDC) Rt down (KΩ) Trim up % 14.85 634.883 1 14.7 400.637 2 14.55 288.513 3 14.4 222.758 4 14.25 179.536 5 14.1 148.959 6 13.95 126.187 7 13.8 108.568 8 13.65 94.532 9 13.5 83.086 10 Vout (VDC) 15.15 15.3 15.45 15.6 15.75 15.9 16.05 16.2 16.35 16.5 Rt up (KΩ) 1460.098 192.573 96.641 61.354 43.016 31.781 24.191 18.72 14.59 11.361 www.aimtec.com F 051e R13.H REV: 04/22/A Tel: +1 514 620 2722 9 of 15 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM20EW-NZ 20 Watt | DC-DC Converter AM20EW-11015S-NZ Trim down % Vout (VDC) Rt down (KΩ) Trim up % Vout (VDC) Rt up (KΩ) 1 14.85 570.165 1 15.15 3208.668 2 14.7 371.335 2 15.3 231.297 3 14.55 271.179 3 15.45 104.85 4 14.4 210.846 4 15.6 63.553 5 14.25 170.524 5 15.75 43.061 6 14.1 141.673 6 15.9 30.815 7 13.95 120.008 7 16.05 22.672 8 13.8 103.142 8 16.2 16.865 9 13.65 89.638 9 16.35 12.516 10 13.5 78.584 10 16.5 9.136 2 14.7 517.391 2 15.3 117.996 3 14.55 346.387 3 15.45 70.541 4 14.4 256.863 4 15.6 48.045 5 14.25 201.789 5 15.75 34.918 6 14.1 164.487 6 15.9 26.315 7 13.95 137.551 7 16.05 20.242 8 13.8 117.187 8 16.2 15.725 9 13.65 101.251 9 16.35 12.235 10 13.5 88.44 10 16.5 9.456 AM20EW-11015SH22-NZ Trim down % Vout (VDC) Rt down (KΩ) Trim up % Vout (VDC) Rt up (KΩ) 1 14.85 974.008 1 15.15 283.713 AM20EW-2418SH30-NZ Trim down % Vout (VDC) Rt down (KΩ) 1 17.82 846.143 2 17.64 527.851 3 17.46 378.438 4 17.28 291.68 5 17.1 234.996 6 16.92 195.059 7 16.74 165.403 8 16.56 142.511 9 16.38 124.305 10 16.2 109.479 Trim up % Vout (VDC) Rt up (KΩ) 1 18.18 1064.151 2 18.36 185.231 3 18.54 94.388 4 18.72 59.784 5 18.9 41.54 6 19.08 30.271 7 19.26 22.62 8 19.44 17.085 9 19.62 12.895 10 19.8 9.613 AM20EW-xx24S-NZ, xx=24 or 48 Trim down % Vout (VDC) 1 23.76 2 23.52 3 23.28 4 23.04 5 22.8 6 22.56 7 22.32 8 22.08 9 21.84 10 21.6 Rt down (KΩ) Trim up % Vout (VDC) Rt up (KΩ) 1038.047 1 24.24 816.889 638.015 2 24.48 179.913 455.256 3 24.72 94.338 350.553 4 24.96 60.463 282.702 5 25.2 42.306 235.158 6 25.44 30.987 199.992 7 25.68 23.256 172.928 8 25.92 17.64 151.453 9 26.16 13.375 134 10 26.4 10.027 2 3 4 5 6 7 8 9 10 AM20EW-11024S-NZ Trim down % Vout (VDC) 1 23.76 23.52 23.28 23.04 22.8 22.56 22.32 22.08 21.84 21.6 Rt down (KΩ) Trim up % Vout (VDC) 1135.537 1 24.24 730.699 2 24.48 532.922 3 24.72 415.701 4 24.96 338.146 5 25.2 283.038 6 25.44 241.862 7 25.68 209.929 8 25.92 184.441 9 26.16 163.624 10 26.4 Rt up (KΩ) 2871.219 219.961 106.182 66.054 45.551 33.104 24.745 18.744 14.226 10.703 AM20EW-11024SH22-NZ Trim down % 1 2 3 4 5 6 7 8 9 10 Vout (VDC) Rt down (KΩ) Trim up % 23.76 1286.2 1 23.52 792.123 2 23.28 565.867 3 23.04 436.104 4 22.8 351.954 5 22.56 292.963 6 22.32 249.316 7 22.08 215.714 8 21.84 189.047 9 21.6 167.37 10 Vout (VDC) 24.24 24.48 24.72 24.96 25.2 25.44 25.68 25.92 26.16 26.4 Rt up (KΩ) 816.889 179.914 94.338 60.464 42.307 30.988 23.257 17.64 13.376 10.027 www.aimtec.com F 051e R13.H REV: 04/22/A Tel: +1 514 620 2722 10 of 15 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM20EW-NZ 20 Watt | DC-DC Converter Derating AM20EW-11005SH22-NZ Free Air Convection Free Air Convection 55°C 40-66 Vin Without heatsink 100 100 65°C 120-160 Vin Without heatsink 60 Safe Operating Area 40 20 65°C 66-120Vin Without heatsink Output Power (%) 70°C 120-160 Vin With heatsink 80 80 60 Safe Operating Area 40 20 0 - 20 - 40 0 20 40 55 65 70 60 0 80 85 100 - 20 - 40 Ambient Temperature º C 0 20 40 65 71 60 80 85 100 Ambient Temperature º C AM20EW-11003SH22-NZ AM20EW-110xxDH30-NZ Free Air Convection Free Air Convection 71ºC With heatsink Without heatsink 100 100 80 120-160Vin Without heatsink 60 Safe Operating Area 40 With heatsink Output Power (%) Output Power (%) 40-120Vin Without heatsink 80 Safe Operating Area 60 40 20 20 0 - 40 - 20 0 20 40 65 71 60 0 80 85 100 - 40 - 20 0 20 40 65 71 60 80 85 100 Ambient Temperature º C Ambient Temperature º C Others Free Air Convection 71 º C without heat sink 100 Output Power (%) Output Power (%) 71°C 66-120Vin With heatsink 60°C 40-66 Vin With heatsink 75º C with heat sink 80 Safe Operating Area 60 40 20 0 - 40 - 20 0 20 40 60 80 85 100 Ambient Temperature º C www.aimtec.com F 051e R13.H REV: 04/22/A Tel: +1 514 620 2722 11 of 15 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM20EW-NZ 20 Watt | DC-DC Converter Typical application circuit + Vin FUSE + Cin DC Vin FUSE Cin 24 Vin 48 Vin - 100 µF / 50V 100 µF / 100V 110Vin 2A Slow blow 10µF - 47µF +Vout + Cout + DC Cout DC - Vin - Vin - Vout + Vout + Vin Cin - Vout Model + Vin + DC - Vin FUSE +Vout + Vout + Vin - Vout Single Vout Cout Dual Vout Cout 3.5 / 5V 9V 12 / 15V 24V 3.5 / 5V 12 / 15V 24V 470µF / 16V 220µF / 16V 220µF / 25V 100µF / 50V 470µF / 16V 220µF / 25V 100µF / 50V ±5V ±9V ±12V / ±15V 220µF / 16V 100µF / 16V 100µF / 25V ±12V / ±15V ±24V 220µF / 25V 100µF / 50V Common + Cout - Vout EMC recommended circuit for 24 & 48V input 1500VDC isolation models CY1 1nF/2KV LDM 4.7uH / 3.1A FUSE + Vin + Vin + C3 330uF/ 50V C2 C1 - Vin + - Vin + Vin + Vin + C1 C3 330uF/ 50V C2 - Vin EMC - Vout EMI + DC - Vin +Vout + Vout + C4 DC Common - Vout + Common C5 - Vout CY2 1nF/2KV C1/C3 C2 C4/C5 24 Vin 48 Vin 330 µF / 50V 330 µF / 100V 1 µF / 50V 1 µF / 100V Refer to Cout in typical application circuit F 051e R13.H REV: 04/22/A C4 - Vout Model www.aimtec.com + CY1 1nF/2KV LDM 4.7uH / 3.1A FUSE DC CY2 1nF/2KV EMI EMC DC +Vout + Vout Tel: +1 514 620 2722 12 of 15 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM20EW-NZ 20 Watt | DC-DC Converter EMC recommended circuit for 110V input 1500VDC isolation models CY1 1nF/2KV FUSE + Vin - Vin AMFW72-0.41NZ PE C1 100uF/ 200V + +Vout + Vout + Vin DC DC - Vin - Vout - Vout CY2 1nF/2KV EMC recommended circuit with EN60950 compliant for 110Vin 2250VDC Isolation LCM2 0.53mH (TN150P-RH 12.7*12.7*7.9) LCM1 Aimtec AMFC22-1NZ + Vin C1 100uF/ 200V - Vin + C2 0.22uF /250V CY1 1000pF/ 400VAC C3 0.22uF/2 50V CY2 1000pF/400VAC PE Vout Cout 3.3V/5V 12V/15V 24V 470 µF 220 µF 100 µF CY3 1000pF/400VAC C4 10~47uF Low ESR +Vout + Vout + Vin DC DC - Vin Cout - Vout - Vout CY4 1000pF/400VAC EMC recommended circuit with EN50155 compliant for 110Vin 2250VDC Isolation CY1 1000pF/400VAC 2A Slow blow type FUSE + Vin - Vin + Vin AMFW72-0.41NZ PE C1 100uF/ 200V + C2 10~47uF /250V Low ESR DC - Vin +Vout + Vout DC - Vout Cout - Vout CY2 1000pF/400VAC Vout Cout 3.3V/5V 9V/12V/15V 18V/24V 470 µF 220 µF 100 µF www.aimtec.com F 051e R13.H REV: 04/22/A Tel: +1 514 620 2722 13 of 15 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM20EW-NZ 20 Watt | DC-DC Converter EMC recommended circuit for 24 & 48V input 3000VDC isolation models LCM 6.8mH FUSE + Vin C1 + C2 CY1 1nF/3KV + Vin C3 C4 - Vin + DC - Vin EMI EMC C1 C2 & C3 C4 24 Vin 48 Vin 1000 µF / 50V 680 µF / 100V 1 µF / 50V 1 µF / 100V 330 µF / 50V 330 µF / 100V Vout Cout 470 µF 220 µF 100 µF DC Cout - Vout - Vout CY2 1nF/3KV Model 3.3V/5V 9V/12V/15V 18V/24V +Vout + Vout EMC recommended circuit with EN60950 compliant for 110V input 3000VDC isolation models CY1 1000pF/400VAC 2A Slow blow type FUSE + Vin - Vin + Vin AMFW72-0.41NZ PE C1 100uF/ 200V + C2 47uF /200V Low ESR DC - Vin +Vout + Vout DC - Vout Cout - Vout CY2 1000pF/400VAC Vout ±12 Vout ±15 & ±24 Vout www.aimtec.com F 051e R13.H REV: 04/22/A Cout 220uF/25V 100uF/35V Tel: +1 514 620 2722 14 of 15 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM20EW-NZ 20 Watt | DC-DC Converter EMC recommended circuit with EN50155 compliant for 110V input 3000VDC isolation models LCM1 30mH + Vin - Vin C1 100uF/ 200V + C2 0.22uF /250V C3 0.22uF/2 50V Vout ±12 Vout ±15 & ±24 Vout CY1 1000pF/ 400VAC CY2 1000pF/400VAC PE CY3 2200pF/400VAC LCM2 30mH + Vin C4 47uF/ 200V DC - Vin +Vout + Vout DC - Vout Cout - Vout CY4 2200pF/400VAC Cout 220uF/25V 100uF/35V NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the date manufactured. 3. Mechanical drawings and specifications are for reference only. 4. All specifications are measured at an ambient temperature of 25°C, humidity