AM20EW-4812D-NZ-STD

Series AM20EW-NZ 20 Watt | DC-DC Converter FEATURES:50 • • • • • Efficiency up to 90% Ultra-wide 4:1 Input range No-load consumption ≤0.15W Over Current protection Input under voltage lockout • • • • • On/Off Remote Control Over Voltage Protection I/Output Isolation 1500, 2250 & 3000VDC Operating Temperature: -40oC to +85oC Continuous Short Circuit protection Models Single output Input Voltage (V) Max Input Current Full/No load (mA) Output Voltage (V) Output Current max (mA) Isolation (VDC) Max Capacitive Load (uF) Efficiency (%) AM20EW-2403S-NZ AM20EW-2405S-NZ AM20EW-2409S-NZ AM20EW-2412S-NZ AM20EW-2415S-NZ AM20EW-2424S-NZ AM20EW-4803S-NZ AM20EW-4805S-NZ AM20EW-4809S-NZ AM20EW-4812S-NZ AM20EW-4815S-NZ AM20EW-4824S-NZ AM20EW-11005S-NZ ⨳ ※ AM20EW-11012S-NZ ⨳ ※ AM20EW-11015S-NZ ⨳ ※ AM20EW-11024S-NZ ⨳ ※ 9-36 9-36 9-36 9-36 9-36 9-36 18-75 18-75 18-75 18-75 18-75 18-75 40-160 40-160 40-160 40-160 818/45 993/45 941/10 941/10 941/10 941/10 409/25 497/25 485/9 485/9 485/9 485/9 212/20 212/20 212/20 212/20 3.3 5 9 12 15 24 3.3 5 9 12 15 24 5 12 15 24 5000 4000 2222 1667 1333 834 5000 4000 2222 1667 1333 834 4000 1667 1333 833 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 10000 10000 4700 1600 1000 500 10000 10000 4700 1600 1000 500 4020 1600 1000 470 86 90 89 89 90 90 86 90 89 89 90 90 89 88 88 88 AM20EW-11003SH22-NZ ※ AM20EW-11005SH22-NZ ※ AM20EW-11012SH22-NZ ※ AM20EW-11015SH22-NZ ※ AM20EW-11024SH22-NZ 40-160 40-160 40-160 40-160 40-160 188/20 222/20 219/8 219/8 219/8 3.3 5 12 15 24 5000 4000 1667 1333 833 2250 2250 2250 2250 2250 10000 10000 1600 1000 470 82 84 85 86 86 AM20EW-2403SH30-NZ AM20EW-2405SH30-NZ AM20EW-2409SH30-NZ AM20EW-2412SH30-NZ AM20EW-2415SH30-NZ AM20EW-2418SH30-NZ ※ AM20EW-2424SH30-NZ AM20EW-4803SH30-NZ AM20EW-4805SH30-NZ AM20EW-4812SH30-NZ AM20EW-4815SH30-NZ AM20EW-4824SH30-NZ 9-36 9-36 9-36 9-36 9-36 9-36 9-36 18-75 18-75 18-75 18-75 18-75 818/45 958/45 967/12 967/12 967/12 969/20 967/12 409/25 484/25 484/8 484/8 484/8 3.3 5 9 12 15 18 24 3.3 5 12 15 24 5000 4000 2222 1667 1333 1111 834 5000 4000 1667 1333 834 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 10000 10000 4700 1600 1000 680 500 10000 10000 1600 1000 500 86 89 88 88 89 89 89 86 88 88 89 89 Output Voltage (V) Output Current max (mA) Isolation (VDC) Max Capacitive Load(uF) ±5 ±9 ±12 ±15 ±2000 ±1111 ±834 ±667 1500 1500 1500 1500 ±4800 ±1000 ±800 ±625 Model Models Dual output Model AM20EW-2405D-NZ AM20EW-2409D-NZ AM20EW-2412D-NZ AM20EW-2415D-NZ www.aimtec.com F 051e R13.H REV: 07/22/A Input Voltage (V) 9-36 9-36 9-36 9-36 Max Input current Full/No load (mA) 993/45 941/10 941/10 941/10 Tel: +1 514 620 2722 1 of 15 Efficiency (Typ.) (%) 86 88 88 88 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM20EW-NZ 20 Watt | DC-DC Converter AM20EW-4805D-NZ AM20EW-4812D-NZ AM20EW-4815D-NZ 18-75 18-75 18-75 497/25 485/9 485/9 ±5 ±12 ±15 ±2000 ±834 ±667 1500 1500 1500 ±4800 ±800 ±625 86 88 89 40-160 217/8 ±12 ±833 3000 ±680 85 AM20EW-11012DH30-NZ ※ 40-160 217/8 ±15 ±667 3000 ±470 86 AM20EW-11015DH30-NZ ※ 40-160 217/8 ±24 ±417 3000 ±220 86 AM20EW-11024DH30-NZ ※ Add suffix “-K” for optional heatsink for metal cased models only. *Add suffix “-ST” for optional screw terminal bottom plate or “-STD” for optional DIN Rail screw terminal bottom plate and reverse voltage protection. Their minimum input voltage and startup voltage have to be increased by 1V. **Add suffix “-K-ST” for optional heatsink and screw terminal bottom plate(for metal cased models only) or “-K-STD” for optional heatsink and DIN Rail screw terminal bottom plate and reverse voltage protection(for metal cased models only). ***Models marked with ⨳ are not recommended for new designs. The optional "-K", "-ST", "-STD", "-K-ST" or "-K-STD" packages for models marked with ⨳ have been obsoleted. NOTE: All specifications in this datasheet are measured at an ambient temperature of 25°C, humidity1000 2000 2200 500 Units VDC VDC MOhm pF Output Specifications Parameters Voltage accuracy Balanced load Over voltage protection Over current protection Short Circuit protection Short circuit restart Line voltage regulation (single) Line voltage regulation (dual) Load voltage regulation (single) Load voltage regulation (dual) www.aimtec.com F 051e R13.H REV: 07/22/A Conditions 110Vin, 3000V isolation, positive output Others Typical ±1 ±1 ±0.5 Zener Diode Clamp 110 120 Continuous, hiccup Auto-Recovery Full load, LL-HL ±0.2 110Vin, 3000V isolation, positive output ±0.2 Full load, LL-HL ±0.5 5% to 100% load for 1500VDC models ±0.5 & 0% to 100% load for others 110Vin, 3000V isolation, positive output ±0.5 Tel: +1 514 620 2722 2 of 15 Maximum ±2 ±3 ±1.5 160 210 Units % % % % of Io ±0.5 ±0.5 ±1 % of Vin ±1 % ±1 % % of Vin Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM20EW-NZ 20 Watt | DC-DC Converter Cross regulation Temperature coefficient Ripple & Noise Voltage adjustment range Transient recovery time Transient recovery deviation 5% to 100% load 50% 1st load, 10-100% 2nd load ±0.5 20MHz Bandwidth, 5% to 100% load 25% load step change, 2250V/3000V isolation 25% load step change, others 25% load step change: 3.3, 5, ±5Vout 25% load step change: others ±5 ±3 ±1.5 ±5 ±0.03 100 ±10 500 800 ±8 ±5 % %/oC mV p-p % µS % General Specifications Parameters Switching frequency Operating temperature Storage temperature Maximum case temperature Cooling Humidity Case material Dimensions (L x W x H) Weight MTBF Maximum soldering temperature Conditions Typical 100% load, 24 & 48 Vin 100% load, 110Vin See derating curve 270 300 Maximum Units KHz oC -40 to +85 oC -55 to +125 105 oC Free air convection 95 % RH Plastic (UL94-V0) Aluminum Alloy 2 x 1 x 0.47 inches 50.8 x 25.4 x 11.8 mm 2.03 x 1.04 x 0.47 inches 51.5 x 26.5 x 12 mm See dimensions drawing 28 (110Vin, 1500VDC Isolated models) Pin mountable without heatsink 26 (Other metal case models) 24 (3000VDC Isolated models) 36 (110Vin, 1500VDC Isolated models) Pin mountable with heatsink 34 (Other metal case models) 32 (3000VDC Isolated models) 50 (110Vin, 1500VDC Isolated models) -ST option without heatsink 48 (Other metal case models) 46 (3000VDC Isolated models) g 58 (110Vin, 1500VDC Isolated models) -ST option with heatsink 56 (Other metal case models) 54 (3000VDC Isolated models) 70 (110Vin, 1500VDC Isolated models) -STD option without heatsink 68 (Other metal case models) 66 (3000VDC Isolated models) 78 (110Vin, 1500VDC Isolated models) -STD option with heatsink 76 (Other metal case models) 74 (3000VDC Isolated models) o >1,000,000 hours (MIL-HDBK -217F, Ground Benign, t=+25 C) oC 1.5mm from case for 10 sec 300 24/48Vin, 3000VDC models Other models Aluminium case Plastic case Optional packages Environment Specification Test Parameters Test mode Acceleration Vibration Vibration (110 Vin/2250VDC isolation) Conditions 10-55Hz 10g, 30min, every axis tested IEC61373 car body 1 B mold Safety Specifications Parameters Agency approvals Standards www.aimtec.com F 051e R13.H REV: 07/22/A cULus UL 62368-1 (with exception of models marked with ※), CE (With exception of 110Vin 3000VDC isolation models) EN 55032, Class B, with EMC recommended circuit EN 50121-3-2, 150kHz-500kHz 99dBuV, 30MHz-230MHz 40dBuV/m at 10m (110Vin, 2250VDC models approved with recommended cirucit) (24/48Vin, 1500VDC & 110Vin, 3000 VDC models meet with recommended cirucit) EN 55016-2-1, 500kHz-30MHz 93dBuV, 230MHz-1GHz 47dBuV/m at 10m (110Vin, 2250VDC models approved with recommended cirucit) (24/48Vin, 1500VDC & 110Vin, 3000 VDC models meet with recommended cirucit) Tel: +1 514 620 2722 3 of 15 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM20EW-NZ 20 Watt | DC-DC Converter Information technology Equipment Railway application Electrostatic Discharge Immunity RF, Electromagnetic Field Immunity Electrical Fast Transient / Burst Immunity Surge Immunity RF, Conducted Disturbance Immunity Voltage dips, Short Interruptions & Voltage variations Immunity IEC/UL 60950-1 EN50155 (110Vin, 2250VDC models compliant) (24/48Vin, 1500VDC and 110Vin, 3000 VDC models meet) IEC 61000-4-2, Contact ±6KV (110Vin 2250/3000VDC Isolation), Contact ±4KV (Others), Criteria B EN50121-3-2, Contact ±6KV/Air ±8KV(24/48Vin 1500VDC and 110Vin 2250/3000VDC Isolation), Criteria B IEC 61000-4-3, 20V/m(110Vin 3000VDC isolation), 10V/m(Others), Criteria A EN50121-3-2, 20V/m (24/48Vin 1500VDC & 110Vin 2250/3000VDC Isolation), Criteria A IEC 61000-4-4, ±4KV (110Vin 2250/3000 VDC Isolation), ±2KV (Others), Criteria B, with external filter EN50121-3-2, ±2KV (24/48Vin 1500VDC & 110Vin 2250/3000VDC Isolation), Criteria A IEC 61000-4-5, ±2KV, Criteria B, with external filter EN50121-3-2, L-L ±1KV (24/48Vin 1500VDC & 110Vin 2250/3000VDC Isolation), Criteria B IEC 61000-4-6, 10 Vrms (2250/3000 VDC Isolated models), 3Vrms (Others), Criteria A EN50121-3-2, 0.15MHz ~ 80MHz, 10 Vrms (24/48Vin 1500VDC & 110Vin 2250/3000VDC Isolation), Criteria B IEC 61000-4-29, 0-70%, Criteria B Pin Out Specifications 2 1 15.24 (0.60) 4 20.32 (0.80) 10.16 (0.40) 5 15.24 (0.60) Notes: All dimensions are typical in millimeters (inches). Pin diameter Tolerance ±0.10 (±0.014) Case Tolerance ±0.50 (±0.02) 4.10 (0.16) DIA 1.00 (0.04) Bottom View 10.16 (0.40) 3 2.54 (0.10) 7.62 5.08 (0.30)(0.20) 10.16 (0.40) 6 2.54 (0.10) 50.80 (2.00) Dual On/Off Control -Vin +Vin -Vout Common +Vout 25.40 (1.00) Single On/Off Control -Vin +Vin -Vout Trim +Vout 11.80 (0.47) Pin 1 2 3 4 5 6 Dimensions metal case Dimensions metal case for 110Vin 3000V isolation dual output models Bottom View 5 1 4 10.16 (0.40) 5.08 10.16 5.08 (0.20) (0.40) (0.20) 2.54 (0.10) F 051e R13.H REV: 07/22/A 4.10 (0.16) 25.40 (1.00) 11.80 (0.47) www.aimtec.com 2 10.16 (0.40) 6 3 DIA 1.00 (0.04) 2.54 (0.10) 45.72 (1.80) 2.54 (0.10) 50.80 (2.00) Notes: All dimensions are typical in millimeters (inches). Pin diameter Tolerance ±0.10 (±0.014) Case Tolerance ±0.50 (±0.02) Tel: +1 514 620 2722 4 of 15 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM20EW-NZ 20 Watt | DC-DC Converter 2.54 (0.10) Dimensions plastic case 51.50 (2.03) 5 Bottom View 1 10.16 (0.40) 2 15.24 (0.60) 4 15.24 (0.60) 20.32 (0.80) 12.00 (0.47) Notes: All dimensions are typical in millimeters (inches). Pin diameter Tolerance ±0.10 (±0.004) Case Tolerance ±0.50 (±0.02) 4.10 (0.16) DIA 1.00 (0.04) DIA 1.00 (0.04) 15.54 (0.61) 10.16 (0.40) 1 4 20.32 (0.80) 15.54 (0.61) Notes: All dimensions are typical in millimeters (inches). Pin diameter Tolerance: ±0.10 (±0.004) Case Tolerance: ±0.50 (±0.02) www.aimtec.com 4.10 (0.16) 6 3 2 Bottom View 5 1 4 2.94 (0.12) 5 5.08 5.08 (0.20) 10.16 (0.20) (0.40) Bottom View 2 2.94 (0.12) 3 10.16 (0.40) 5.08 7.62 (0.20) 10.56 (0.30) (0.42) 6 2.54 (0.10) 51.4 (2.02) 45.72 (1.80) 10.16 (0.40) 2.94 (0.12) DIA 1.00 (0.04) Side view 10.16 (0.40) Side view 16.50 (0.65) Optional -K heatsink for 110V 3000V isolation dual output models 4.10 (0.16) 16.50 (0.65) Optional -K heatsink F 051e R13.H REV: 07/22/A 10.16 (0.40) 3 2.54 (0.10) 26.50 (1.04) 5.08 7.62 (0.20) (0.30) 10.16 (0.40) 6 Notes: All dimensions are typical in millimeters (inches). Pin diameter Tolerance: ±0.10 (±0.004) Case Tolerance: ±0.50 (±0.02) Tel: +1 514 620 2722 5 of 15 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM20EW-NZ 20 Watt | DC-DC Converter Dimensions with -ST options Pin Out Specifications 76.00 (2.99) 61.60 (2.43) LED light 6 Top view 2 3 23.00 (0.91) 31.50 (1.24) 1 5 Pin Single Single 1 2 3 4 5 6 On/Off Control -Vin +Vin + Vout Trim - Vout On/Off Control -Vin +Vin + Vout Common - Vout 4 8.80 (0.35) Side view 21.20 (0.84) Dimensions: mm (inch) Case Tolerance:± 0.50 (0.02) Wire gauge: 24-12AWG Dimensions with -STD options Pin Out Specifications 76.00 (2.99) 61.60 (2.43) LED light 6 Top view 2 3 5 23.00 (0.91) 31.50 (1.24) 1 Pin Single Single 1 2 3 4 5 6 On/Off Control -Vin +Vin + Vout Trim - Vout On/Off Control -Vin +Vin + Vout Common - Vout 4 25.80 (1.02) Side view 9.80 (0.39) Ø3.30 Ø0.13 Dimensions: mm (inch) Case Tolerance:± 1.00 (0.04) Wire gauge: 24-12AWG www.aimtec.com F 051e R13.H REV: 07/22/A Tel: +1 514 620 2722 6 of 15 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM20EW-NZ 20 Watt | DC-DC Converter Dimensions with heatsink and -ST options Pin Out Specifications 76.00 (2.99) 61.60 (2.43) LED light 6 Top view 2 3 23.00 (0.91) 31.50 (1.24) 1 5 Pin Single Single 1 2 3 4 5 6 On/Off Control -Vin +Vin + Vout Trim - Vout On/Off Control -Vin +Vin + Vout Common - Vout 4 25.30 (1.00) Dimensions: mm (inch) Case Tolerance:± 0.50 (0.02) Wire gauge: 24-12AWG 8.80 (0.35) 21.20 (0.84) Side view Dimensions with heatsink and -STD options Pin Out Specifications 76.00 (2.99) 61.60 (2.43) LED light 6 Top view 2 3 5 Single Single 1 2 3 4 5 6 On/Off Control -Vin +Vin + Vout Trim - Vout On/Off Control -Vin +Vin + Vout Common - Vout 23.00 (0.91) 31.50 (1.24) 1 Pin 4 25.80 (1.02) 29.90 (1.18) Side view 9.80 (0.39) Ø3.30 Ø0.13 Dimensions: mm (inch) Case Tolerance:± 0.50 (0.02) Wire gauge: 24-12AWG www.aimtec.com F 051e R13.H REV: 07/22/A Tel: +1 514 620 2722 7 of 15 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM20EW-NZ 20 Watt | DC-DC Converter Trimming Output voltage can be externally trimmed by utilizing the methods as shown below Fixed Resistor Variable Potentiometer Leave open if not used. AM20EW-xx03S-NZ, xx=24 or 48 Trim down % 1 2 3 4 5 6 7 8 9 10 3.27 3.23 3.2 3.17 3.14 3.1 3.07 3.04 3 2.97 Rt down (KΩ) Trim up % 124.138 1 73.217 2 53.983 3 41.497 4 32.737 5 24.449 6 19.839 7 16.148 8 12.236 9 9.856 10 Vout (VDC) Rt up (KΩ) 3.33 -556.59 3.37 194.738 3.4 89.364 3.43 55.05 3.47 34.131 3.5 25.35 3.53 19.357 3.56 15.006 3.6 10.773 3.63 8.367 Vout (VDC) AM20EW-11003SH22-NZ Trim down % Vout (VDC) 1 3.267 2 3.234 3 3.201 4 3.168 5 3.135 6 3.102 7 3.069 8 3.036 9 3.003 10 2.97 Rt down (KΩ) Trim up % Vout (VDC) 210.002 1 3.333 103.334 2 3.366 72.327 3 3.399 54.213 4 3.432 42.335 5 3.465 31.667 6 3.498 25.963 7 3.531 21.505 8 3.564 16.884 9 3.597 14.124 10 3.63 Rt up (KΩ) 369.179 96.88 59.466 41.454 28.235 22.058 17.6 14.23 10.837 8.857 AM20EW-xx05S-NZ, xx=24 or 48 Trim down % Vout (VDC) 1 4.95 2 4.9 3 4.85 4 4.8 5 4.75 6 4.7 7 4.65 8 4.6 9 4.55 10 4.5 Rt down (KΩ) 105.18 52.153 31.996 21.377 14.822 10.372 7.154 4.719 2.811 1.276 Trim up % Vout (VDC) 1 5.05 2 5.1 3 5.15 4 5.2 5 5.25 6 5.3 7 5.35 8 5.4 9 5.45 10 5.5 Rt up (KΩ) 176.356 71.279 41.973 28.2 20.197 14.967 11.281 8.543 6.43 4.749 AM20EW-11005S-NZ Trim down % Vout (VDC) 1 4.95 2 4.9 3 4.85 4 4.8 5 4.75 6 4.7 7 4.65 8 4.6 9 4.55 10 4.5 Rt down (KΩ) 96.08 49.349 30.67 20.616 14.333 10.034 6.909 4.533 2.667 1.162 Trim up % Vout (VDC) 1 5.05 2 5.1 3 5.15 4 5.2 5 5.25 6 5.3 7 5.35 8 5.4 9 5.45 10 5.5 Rt up (KΩ) 205.698 76.406 44.023 29.296 20.879 15.431 11.617 8.798 6.63 4.91 www.aimtec.com F 051e R13.H REV: 07/22/A Tel: +1 514 620 2722 8 of 15 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM20EW-NZ 20 Watt | DC-DC Converter AM20EW-11005SH22-NZ Trim down % 1 2 3 4 5 6 7 8 9 10 4.95 4.9 4.85 4.8 4.75 4.7 4.65 4.6 4.55 4.5 Rt down (KΩ) 105.181 52.154 31.997 21.378 14.823 10.373 7.155 4.719 2.811 1.277 Trim up % Vout (VDC) Rt up (KΩ) 1 5.05 176.356 2 5.1 71.279 3 5.15 41.974 4 5.2 28.2 5 5.25 20.198 6 5.3 14.967 7 5.35 11.281 8 5.4 8.544 9 5.45 6.43 10 5.5 4.749 Vout (VDC) AM20EW-xx09S-NZ, xx=24 or 48 Trim down % 1 2 3 4 5 6 7 8 9 10 Vout (VDC) Rt down (KΩ) Trim up % 8.91 375.532 1 8.82 207.429 2 8.73 139.156 3 8.64 102.145 4 8.55 78.924 5 8.46 62.996 6 8.37 51.392 7 8.28 42.562 8 8.19 35.616 9 8.1 30.011 10 Vout (VDC) 9.09 9.18 9.27 9.36 9.45 9.54 9.63 9.72 9.81 9.9 Rt up (KΩ) 314.531 112.638 64.147 42.357 29.974 21.989 16.412 12.296 9.134 6.628 AM20EW-xx12S-NZ, xx=24 or 48 Trim down % 1 2 3 4 5 6 7 8 9 10 Vout (VDC) Rt down (KΩ) 11.88 496.091 11.76 301.451 11.64 212.527 11.52 161.585 11.4 128.573 11.28 105.441 11.16 88.332 11.04 75.163 10.92 64.715 10.8 56.223 Trim up % 1 2 3 4 5 6 7 8 9 10 Vout (VDC) Rt up (KΩ) 12.12 706.435 12.24 158.92 12.36 83.878 12.48 54.074 12.6 38.076 12.72 28.095 12.84 21.274 12.96 16.316 13.08 12.551 13.2 9.594 AM20EW-11012S-NZ Trim down % 1 2 3 4 5 6 7 8 9 10 11.88 11.76 11.64 11.52 11.4 11.28 11.16 11.04 10.92 10.8 Rt down (KΩ) Trim up % 505.529 1 303.041 2 211.851 3 159.978 4 126.504 5 103.114 6 85.849 7 72.581 8 62.066 9 53.527 10 Vout (VDC) Rt up (KΩ) 12.12 614.769 12.24 150.097 12.36 78.994 12.48 50.198 12.6 34.607 12.72 24.832 12.84 18.13 12.96 13.249 13.08 9.536 13.2 6.616 Vout (VDC) AM20EW-11012SH22-NZ Trim down % Vout (VDC) 1 11.88 2 11.76 3 11.64 4 11.52 5 11.4 6 11.28 7 11.16 8 11.04 9 10.92 10 10.8 Rt down (KΩ) Trim up % Vout (VDC) 496.092 1 12.12 301.452 2 12.24 212.527 3 12.36 161.585 4 12.48 128.573 5 12.6 105.442 6 12.72 88.332 7 12.84 75.164 8 12.96 64.716 9 13.08 56.223 10 13.2 Rt up (KΩ) 706.435 158.92 83.879 54.075 38.077 28.095 21.274 16.317 12.552 9.595 AM20EW-xx15S-NZ, xx=24 or 48 Trim down % Vout (VDC) 1 14.85 2 14.7 3 14.55 4 14.4 5 14.25 6 14.1 7 13.95 8 13.8 9 13.65 10 13.5 Rt down (KΩ) 634.883 400.637 288.513 222.758 179.536 148.959 126.187 108.568 94.532 83.086 Trim up % 1 2 3 4 5 6 7 8 9 10 Vout (VDC) 15.15 15.3 15.45 15.6 15.75 15.9 16.05 16.2 16.35 16.5 Rt up (KΩ) 1460.098 192.573 96.641 61.354 43.016 31.781 24.191 18.72 14.59 11.361 www.aimtec.com F 051e R13.H REV: 07/22/A Tel: +1 514 620 2722 9 of 15 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM20EW-NZ 20 Watt | DC-DC Converter AM20EW-11015S-NZ Trim down % 1 2 3 4 5 6 7 8 9 10 14.85 14.7 14.55 14.4 14.25 14.1 13.95 13.8 13.65 13.5 Rt down (KΩ) 570.165 371.335 271.179 210.846 170.524 141.673 120.008 103.142 89.638 78.584 Trim up % Vout (VDC) Rt up (KΩ) 1 15.15 3208.668 2 15.3 231.297 3 15.45 104.85 4 15.6 63.553 5 15.75 43.061 6 15.9 30.815 7 16.05 22.672 8 16.2 16.865 9 16.35 12.516 10 16.5 9.136 Vout (VDC) AM20EW-11015SH22-NZ Trim down % 1 2 3 4 5 6 7 8 9 10 Vout (VDC) Rt down (KΩ) Trim up % 14.85 974.008 1 14.7 517.391 2 14.55 346.387 3 14.4 256.863 4 14.25 201.789 5 14.1 164.487 6 13.95 137.551 7 13.8 117.187 8 13.65 101.251 9 13.5 88.44 10 Vout (VDC) 15.15 15.3 15.45 15.6 15.75 15.9 16.05 16.2 16.35 16.5 Rt up (KΩ) 283.713 117.996 70.541 48.045 34.918 26.315 20.242 15.725 12.235 9.456 AM20EW-2418SH30-NZ Trim down % 1 2 3 4 5 6 7 8 9 10 Vout (VDC) Rt down (KΩ) 17.82 846.143 17.64 527.851 17.46 378.438 17.28 291.68 17.1 234.996 16.92 195.059 16.74 165.403 16.56 142.511 16.38 124.305 16.2 109.479 Trim up % 1 2 3 4 5 6 7 8 9 10 Vout (VDC) Rt up (KΩ) 18.18 1064.151 18.36 185.231 18.54 94.388 18.72 59.784 18.9 41.54 19.08 30.271 19.26 22.62 19.44 17.085 19.62 12.895 19.8 9.613 AM20EW-xx24S-NZ, xx=24 or 48 Trim down % 1 2 3 4 5 6 7 8 9 10 23.76 23.52 23.28 23.04 22.8 22.56 22.32 22.08 21.84 21.6 Rt down (KΩ) Trim up % 1038.047 1 638.015 2 455.256 3 350.553 4 282.702 5 235.158 6 199.992 7 172.928 8 151.453 9 134 10 Vout (VDC) Rt up (KΩ) 24.24 816.889 24.48 179.913 24.72 94.338 24.96 60.463 25.2 42.306 25.44 30.987 25.68 23.256 25.92 17.64 26.16 13.375 26.4 10.027 Vout (VDC) AM20EW-11024S-NZ Trim down % Vout (VDC) 1 23.76 2 23.52 3 23.28 4 23.04 5 22.8 6 22.56 7 22.32 8 22.08 9 21.84 10 21.6 Rt down (KΩ) Trim up % Vout (VDC) 1135.537 1 24.24 730.699 2 24.48 532.922 3 24.72 415.701 4 24.96 338.146 5 25.2 283.038 6 25.44 241.862 7 25.68 209.929 8 25.92 184.441 9 26.16 163.624 10 26.4 Rt up (KΩ) 2871.219 219.961 106.182 66.054 45.551 33.104 24.745 18.744 14.226 10.703 AM20EW-11024SH22-NZ Trim down % Vout (VDC) 1 23.76 2 23.52 3 23.28 4 23.04 5 22.8 6 22.56 7 22.32 8 22.08 9 21.84 10 21.6 Rt down (KΩ) 1286.2 792.123 565.867 436.104 351.954 292.963 249.316 215.714 189.047 167.37 Trim up % 1 2 3 4 5 6 7 8 9 10 Vout (VDC) 24.24 24.48 24.72 24.96 25.2 25.44 25.68 25.92 26.16 26.4 Rt up (KΩ) 816.889 179.914 94.338 60.464 42.307 30.988 23.257 17.64 13.376 10.027 www.aimtec.com F 051e R13.H REV: 07/22/A Tel: +1 514 620 2722 10 of 15 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM20EW-NZ 20 Watt | DC-DC Converter Derating AM20EW-11005SH22-NZ Free Air Convection Free Air Convection 55°C 40-66 Vin Without heatsink 71°C 66-120Vin With heatsink 60°C 40-66 Vin With heatsink 65°C 120-160 Vin Without heatsink 60 Safe Operating Area 40 20 65°C 66-120Vin Without heatsink Output Power (%) 70°C 120-160 Vin With heatsink 80 80 60 Safe Operating Area 40 20 0 - 20 - 40 0 20 40 55 65 70 60 0 80 85 100 - 20 - 40 Ambient Temperature º C 0 20 40 65 71 60 80 85 100 Ambient Temperature º C AM20EW-11003SH22-NZ AM20EW-110xxDH30-NZ Free Air Convection Free Air Convection 71ºC With heatsink Without heatsink 100 100 80 120-160Vin Without heatsink 60 Safe Operating Area 40 With heatsink Output Power (%) Output Power (%) 40-120Vin Without heatsink 80 Safe Operating Area 60 40 20 20 0 0 - 40 - 20 0 20 40 65 71 60 80 85 100 - 40 - 20 0 20 40 65 71 60 80 85 100 Ambient Temperature º C Ambient Temperature º C Others Free Air Convection 71 º C without heat sink 100 75º C with heat sink Output Power (%) Output Power (%) 100 100 80 Safe Operating Area 60 40 20 0 - 40 - 20 0 20 40 60 80 85 100 Ambient Temperature º C www.aimtec.com F 051e R13.H REV: 07/22/A Tel: +1 514 620 2722 11 of 15 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM20EW-NZ 20 Watt | DC-DC Converter Typical application circuit + Vin FUSE + Cin DC FUSE +Vout + Vout + Vin + Vin + DC + Vout + Vin Cout + Cin DC DC Cout Vin - Vin Model FUSE Cin 24 Vin 48 Vin - 100 µF / 50V 100 µF / 100V 110Vin 2A Slow blow 10µF - 47µF - Vin - Vin - Vout - Vout +Vout + - Vout Single Vout Cout Dual Vout Cout 3.5 / 5V 9V 12 / 15V 24V 3.5 / 5V 12 / 15V 24V 470µF / 16V 220µF / 16V 220µF / 25V 100µF / 50V 470µF / 16V 220µF / 25V 100µF / 50V ±5V ±9V ±12V / ±15V 220µF / 16V 100µF / 16V 100µF / 25V ±12V / ±15V ±24V 220µF / 25V 100µF / 50V Common + Cout - Vout EMC recommended circuit for 24 & 48V input 1500VDC isolation models CY1 1nF/2KV LDM 4.7uH / 3.1A FUSE + Vin + Vin + C3 330uF/ 50V C2 C1 + DC - Vin - Vin + C4 - Vout - Vout CY1 1nF/2KV LDM 4.7uH / 3.1A FUSE DC CY2 1nF/2KV EMI EMC +Vout + Vout + Vin + Vin +Vout + Vout + C4 + C1 C3 330uF/ 50V C2 + DC - Vin - Vin EMC EMI DC Common - Vout C1/C3 C2 C4/C5 24 Vin 48 Vin 330 µF / 50V 330 µF / 100V 1 µF / 50V 1 µF / 100V Refer to Cout in typical application circuit F 051e R13.H REV: 07/22/A C5 - Vout CY2 1nF/2KV Model www.aimtec.com Common + Tel: +1 514 620 2722 12 of 15 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM20EW-NZ 20 Watt | DC-DC Converter EMC recommended circuit for 110V input 1500VDC isolation models CY1 1nF/2KV FUSE + Vin - Vin AMFW72-0.41NZ C1 100uF/ 200V +Vout + Vout + Vin + DC DC - Vin PE - Vout - Vout CY2 1nF/2KV EMC recommended circuit with EN60950 compliant for 110Vin 2250VDC Isolation LCM2 0.53mH (TN150P-RH 12.7*12.7*7.9) LCM1 Aimtec AMFC22-1NZ + Vin C1 100uF/ 200V - Vin + C2 0.22uF /250V CY1 1000pF/ 400VAC C3 0.22uF/2 50V CY2 1000pF/400VAC PE Vout CY3 1000pF/400VAC C4 10~47uF Low ESR +Vout + Vout + Vin DC DC - Vin Cout - Vout - Vout CY4 1000pF/400VAC Cout 3.3V/5V 12V/15V 24V 470 µF 220 µF 100 µF EMC recommended circuit with EN50155 compliant for 110Vin 2250VDC Isolation CY1 1000pF/400VAC 2A Slow blow type FUSE + Vin - Vin + Vin AMFW72-0.41NZ PE C1 100uF/ 200V + C2 10~47uF /250V Low ESR DC - Vin +Vout + Vout DC - Vout Cout - Vout CY2 1000pF/400VAC Vout Cout 3.3V/5V 9V/12V/15V 18V/24V 470 µF 220 µF 100 µF www.aimtec.com F 051e R13.H REV: 07/22/A Tel: +1 514 620 2722 13 of 15 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM20EW-NZ 20 Watt | DC-DC Converter EMC recommended circuit for 24 & 48V input 3000VDC isolation models LCM 6.8mH FUSE + Vin CY1 1nF/3KV + Vin + + C2 C1 C3 C4 - Vin DC - Vin Model C1 C2 & C3 C4 24 Vin 48 Vin 1000 µF / 50V 680 µF / 100V 1 µF / 50V 1 µF / 100V 330 µF / 50V 330 µF / 100V Vout Cout 3.3V/5V 9V/12V/15V 18V/24V 470 µF 220 µF 100 µF DC Cout - Vout - Vout CY2 1nF/3KV EMI EMC +Vout + Vout EMC recommended circuit with EN60950 compliant for 110V input 3000VDC isolation models CY1 1000pF/400VAC 2A Slow blow type FUSE + Vin - Vin + Vin AMFW72-0.41NZ PE C1 100uF/ 200V + C2 47uF /200V Low ESR DC - Vin +Vout + Vout DC - Vout Cout - Vout CY2 1000pF/400VAC Vout ±12 Vout ±15 & ±24 Vout www.aimtec.com F 051e R13.H REV: 07/22/A Cout 220uF/25V 100uF/35V Tel: +1 514 620 2722 14 of 15 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM20EW-NZ 20 Watt | DC-DC Converter EMC recommended circuit with EN50155 compliant for 110V input 3000VDC isolation models LCM1 30mH + Vin - Vin C1 100uF/ 200V + C2 0.22uF /250V C3 0.22uF/2 50V Vout ±12 Vout ±15 & ±24 Vout CY1 1000pF/ 400VAC CY2 1000pF/400VAC PE CY3 2200pF/400VAC LCM2 30mH + Vin C4 47uF/ 200V DC - Vin +Vout + Vout DC - Vout Cout - Vout CY4 2200pF/400VAC Cout 220uF/25V 100uF/35V NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the date manufactured. 3. Mechanical drawings and specifications are for reference only. 4. All specifications are measured at an ambient temperature of 25°C, humidity