AM2L-0505SH60-NZTR

Click on Series name for product info on aimtec.com Series AM2L-NZ Not Recommended For New Design 2 Watt | DC-DC Converter FEATURES: • • • • • • • Low Profile SMD 1000VDC & 6000VDC Isolation Industry Standard Pinout Unregulated Single & Dual Outputs MTBF>1,000,000 hours Operating temperature: -40°C to +85°C High Efficiency up to 85% Models Single output Model Input Voltage (V) AM2L-0505SH60-NZ AM2L-1205SH60-NZ ※ AM2L-1215SH60-NZ ※ AM2L-2405SH60-NZ ※ Output Voltage (V) 4.5-5.5 10.8-13.2 10.8-13.2 21.6-26.4 Output Current max(mA) 5 5 15 5 400 400 133 400 Isolation (VDC) Efficiency (%) 6000 6000 6000 6000 77 78 81 79 NOTE: All specifications in this datasheet are measured at an ambient temperature of 25°C, humidity1000 Output Specifications Parameters Voltage accuracy Short Circuit protection Short Circuit Restart Line voltage regulation Load voltage regulation (5 Vout) Load voltage regulation (12 Vout) Load voltage regulation (15 Vout) Temperature coefficient Ripple & Noise* Minimum Load Current** Conditions Typical See Tolerance Graph 6000VDC Continuous Maximum Units 1 % Sec ±5 For a 1% change of Vin From 10% load to 100% load At 100% load 20MHz Bandwidth Auto-Recovery ±1.2 12.8 6.8 6.3 ±0.03 150 10 % % %/oC mV p-p % of Max *Test ripple & noise by “Parallel Cable Method” as described in Application Note “Ripple and Noise Measurement of Brick & POL DC-DC Converters” available on Aimtec’s website www.aimtec.com **If the operating output current is less than 10% of maximum it is recommended to install a load resister in parallel with the load to ensure the actual load current meets the minimum load current requirement. General Specifications Parameters Switching frequency Operating temperature Storage temperature Maximum case temperature www.aimtec.com F 051e R12.S REV: 05/20/A Conditions Typical 100% load, nominal input 100 Maximum Units 100 KHz oC oC oC -40 to + 85 -55 to + 125 Tel: +1 514 620 2722 1 of 3 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM2L-NZ Not Recommended For New Design 2 Watt | DC-DC Converter Cooling Humidity Case material Weight Dimensions (L x W x H) MTBF Maximum Soldering Temperature Free Air Convection 95 % RH Plastic(UL94-V0) 6000VDC 3.8 g Single 6000VDC 0.94 x 0.79 x 0.32 inches 23.86 x 18.50 x 8.00mm >1,000, 000 hours (MIL-HDBK -217F, Ground Benign, t=+25ºC) oC 1.5mm from case for 10 seconds 260 Safety Specifications Parameters Agency approvals CE EN 60601-1-1; EN 60601-1-2 Standards Pin Out Specifications Pin Single 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 - V in No Pin No Pin No Pin No Pin No Pin NC NC +V out -V out No Pin No Pin No Pin No Pin No Pin +V in Typical Voltage Accuracy Characteristics Tolerance Envelope Graph +10% Typical Load Line +5% +2.5% Output Voltage -2.5% 10% -7.5% 50% Output Current(%) 100% NOTE: On dual output models Pin 5 and Pin 10 are connected internally together. Either Pin 5 or Pin 10, or both can be used as the -Vout NC: not connected Dimensions Side View 23.86 (0.94) Front View 8.00 7.50 (0.32) (0.30) A 3.04 (0.12) 13.10 (0.52) 2.54 (0.10) 2.00 (0.08) Top View 1.00 (0.04) 16 18.50 (0.73) A 10 9 0.50 (0.01) 18.50 13.70 (0.73) (0.54) 1 7 8 5.00º angle 1.35 ± 0.13 (0.05 ± 0.005) MAX 15.24 (0.60) Recommended Filter Circuit www.aimtec.com F 051e R12.S REV: 05/20/A Tel: +1 514 620 2722 2 of 3 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Not Recommended For New Design Series AM2L-NZ 2 Watt | DC-DC Converter L Single Output L +Vout + Vin + Cin + DC DC - Vin Cout - Vin If it is required to decrease the input/output ripple an “LC” filter network can be installed on the input and output of the converter (see above). It should be noted that the inductance and the resonant frequency of the “LC” filtering network should differ from the DC/DC converter switching frequency to avoid mutual interference. The capacitance of the outputfilter capacitor must not exceed the values in the Table below to avoid startup problems and ensure safe and reliable operation. It’s not recommended to connect any external capacitor in the application field whenoutput loading is less than 0.5 watt. External Capacitor Tables Input Capacitor (Cin) Vin (VDC) Cin (uF) 5 12 24 4.7 2.2 1 Output Capacitor (Cout) Single Vout (VDC) 5 15 Cout (uF) 10 1 Overload Protection The output circuit of these products has no protection against overload. It is recommended to install external overload protection in the form of a self-recovery fuse or a circuit breaker in series at the converter’s input. To achieve a high degree of output voltage regulation, over-voltage, and over-current protection it is suggested to use the AM2LV-NZ series as an alternative. NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the date manufactured. 3. Mechanical drawings and specifications are for reference only. 4. All specifications are measured at an ambient temperature of 25°C, humidity