AM30EW-2424S-NZ

Series AM30EW-NZ 30 Watt | DC-DC Converter FEATURES: • • • • • Efficiency up to 90% Ultra-wide 4:1 Input range No-load consumption ≤0.14W Operating Temperature: -40oC to +75oC Input under voltage lockout • • • • • On/Off Remote Control Over Voltage Protection I/Output Isolation 1500VDC Over Current protection Continuous Short Circuit protection Models Single output Model AM30EW-2403S-NZ AM30EW-2405S-NZ AM30EW-2409S-NZ AM30EW-2412S-NZ AM30EW-2415S-NZ AM30EW-2424S-NZ AM30EW-4803S-NZ AM30EW-4805S-NZ AM30EW-4812S-NZ AM30EW-4815S-NZ AM30EW-4824S-NZ Input Voltage (VDC) Max Input current Full/No load (mA) Output Voltage (VDC) Output Current max (mA) Isolation (VDC) Max Capacitive Load(uF) Efficiency (%) 9-36‡ 9-36‡ 9-36‡ 9-36‡ 9-36‡ 9-36‡ 18-75 18-75 18-75 18-75 18-75 993/100 1453/100 1488/12 1488/12 1488/12 1488/12 485/30 726/35 744/10 744/10 744/10 3.3 5 9 12 15 24 3.3 5 12 15 24 6000 6000 3333 2500 2000 1250 6000 6000 2500 2000 1250 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 10000 10000 4700 2700 1680 680 10000 10000 2700 1680 680 85 88 88 90 90 90 87 88 89 89 89 Input Voltage (VDC) Max Input current Full/No load (mA) Output Voltage (VDC) Output Current max (mA) Isolation (VDC) Max Capacitive Load(uF) Efficiency (%) Dual output Model AM30EW-2405D-NZ 9-36‡ 1453/100 ±5 ±3000 1500 2000 86 AM30EW-2412D-NZ 9-36‡ 1488/12 ±12 ±1250 1500 1250 89 AM30EW-2415D-NZ 9-36‡ 1488/12 ±15 ±1000 1500 680 89 AM30EW-2424D-NZ 9-36‡ 1488/12 ±24 ±625 1500 470 89 AM30EW-4805D-NZ 18-75 726/35 ±5 ±3000 1500 2000 86 AM30EW-4812D-NZ 18-75 744/10 ±12 ±1250 1500 1250 88 AM30EW-4815D-NZ 18-75 744/10 ±15 ±1000 1500 680 88 ‡ At Input range 9-18VDC output power will be rated at 80%. *Add suffix “-ST” for optional screw terminal bottom plate or “-STD” for optional DIN Rail screw terminal bottom plate. **Add suffix “-K” for optional heatsink, “-K-ST” for optional heatsink and screw terminal bottom plate or “-K-STD” for optional heatsink and DIN Rail screw terminal bottom plate. NOTE: All specifications in this datasheet are measured at an ambient temperature of 25°C, humidity1000 2000 Maximum Units VDC MOhm pF Output Specifications Parameters Voltage accuracy Over voltage protection Over current protection Short Circuit protection Short circuit restart Line voltage regulation Load voltage regulation Conditions Typical Maximum Units ±3 160 190 % % % of Io ±1 Zener Diode Clamp 110 110 Continuous, hiccup Auto-Recovery Positive output ±0.2 Full load, LL-HL Negative output ±0.5 Positive output ±0.5 0% to 100% load Negative output ±0.5 ±0.5 ±1 ±1 ±1.5 ±0.03 100 150 ±10 500 ±8 ±5 Temperature coefficient Single output Dual output 20MHz Bandwidth, 100% load Ripple & Noise Voltage adjustment range Transient recovery time Transient recovery deviation 50 50 25% load step change 25% load step change: 3.3, 5, ±5Vout 25% load step change: others 300 ±5 ±3 % of Vin % %/oC mV p-p % µS % General Specifications Parameters Switching frequency Operating temperature Storage temperature Maximum case temperature Cooling Humidity Case material Weight Dimensions (L x W x H) MTBF Maximum soldering temperature Conditions Typical 100% load See derating curve 300 Maximum Units 100 KHz oC oC oC -40 to +80 -55 to +125 Free air convection 95 % RH Aluminum Alloy Pin mountable 26 With optional -ST mounting plate: 48 With optional -STD mounting plate: 68 g With optional -K Pin mountable 34 With optional -ST-K mounting plate: 56 With optional -STD-K mounting plate: 76 Pin mountable 2.00 x 1.00 x 0.46 inches 50.80 x 25.40 x 11.80 mm With optional -ST mounting plate: 2.99 x 1.24 x 0.84 inches 76.00 x 31.50 x 21.20 mm With optional -STD mounting plate: 2.99 x 1.24 x 1.00 inches 76.00 x 31.50 x 25.30 mm With optional -K Pin mountable 2.02 x 1.03 x 0.65 inches 51.40 x 26.20 x 16.50 mm With optional -ST-K mounting plate: 2.99 x 1.24 x 1.02 inches 76.00 x 31.50 x 25.80 mm With optional -STD-K mounting plate: 2.99 x 1.24 x 1.18 inches 76.00 x 31.50 x 29.90 mm o >1,000,000 hours (MIL-HDBK -217F, Ground Benign, t=+25 C) oC 1.5mm from case for 10 sec 300 Environment Specification Test Vibration www.aimtec.com F 051e R13.C REV:05/21/A Parameters Test mode Acceleration Conditions 10-55Hz 10g, 30min, every axis tested Tel: +1 514 620 2722 2 of 10 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM30EW-NZ 30 Watt | DC-DC Converter Safety Specifications Parameters Approval Standards EN62368-1 , UL60950-1 with exception of the dual output models CISPR32/EN 55032, Class A(Bare component), Class B, with EMC recommended circuit Electrostatic Discharge Immunity IEC 61000-4-2, Contact ±4KV, Criteria B RF, Electromagnetic Field Immunity IEC 61000-4-3, 10V/m, Criteria A IEC 61000-4-4, ±2KV, Criteria B, with external filter Electrical Fast Transient / Single output Burst Immunity Dual output IEC 61000-4-4, ±2KV, Criteria B, with external filter Single output IEC 61000-4-5, ±2KV, Criteria B, with external filter Surge Immunity Dual output IEC 61000-4-5, ±2KV, Criteria B, with external filter IEC 61000-4-6, 3Vrms, Criteria A RF, Conducted Disturbance Single output Immunity Dual output IEC 61000-4-6, 10Vrms, Criteria A Pin Out Specifications 50.80 (2.00) 2 5 7.62 (0.30) 2.54 (0.10) 25.40 (1.00) 6 3 Top View 1 4 45.72 (1.80) 2.54 10.16 (0.10) (0.40) 5.08 (0.20) Bottom View 10.16 2.54 (0.40) (0.10) Dimensions Pin 1 2 3 4 5 6 Single On/Off Control -Vin +Vin Trim -Vout +Vout Dual On/Off Control -Vin +Vin -Vout Common +Vout 11.80 (0.47) Printed Face Note: Unit: mm (inch) General tolerances: ±0.50 (±0.02) Side View 4.10 (0.16) 1.00 (0.04) Heatsink Option: AM30EW-NZ-K Top View 51.40 (2.02) 6 10.16 (0.40) 3 2 5 10.16 (0.40) 7.62 (0.30) 26.20 (1.03) 2.54 (0.10) 5.08 (0.20) Bottom View 1 4 16.50 (0.65) 45.72 (1.80) Note: Unit: mm (inch) General tolerances: ±0.50 (±0.02) 1.00 (0.04) www.aimtec.com F 051e R13.C REV:05/21/A 4.10 (0.16) Side View Tel: +1 514 620 2722 3 of 10 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM30EW-NZ 30 Watt | DC-DC Converter Screw Terminal Option: AM30EW-NZ-ST 76.00 (2.99) 61.60 (2.43) 23.00 (0.91) Ø3.30 31.50 (1.24) Pin Out Specifications 1 2 3 4 5 6 Top View Pin Single Dual 1 2 3 4 5 6 On/Off Control -Vin +Vin Trim - Vout + Vout On/Off Control -Vin +Vin - Vout Common + Vout Side View 8.80 (0.35) 21.20 (0.84) Ø3.30 Note: Unit: mm (inch) Wire range: 24-12 AWG Tightening torque: Max 0.4 N*m General tolerances: ±0.50 (±0.02) Screw Terminal with Heatsink Option: AM30EW-NZ-K-ST Top View 76.00 (2.99) 61.60 (2.43) 23.00 (0.91) 31.50 (1.24) Ø3.30 1 2 3 4 5 6 www.aimtec.com F 051e R13.C REV:05/21/A Side View 8.80 (0.35) 25.30 (1.00) 21.20 (0.84) Ø3.30 Tel: +1 514 620 2722 4 of 10 Note: Unit: mm (inch) Wire range: 24-12 AWG Tightening torque: Max 0.4 N*m General tolerances: ±0.50 (±0.02) Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM30EW-NZ 30 Watt | DC-DC Converter DIN-RAIL Option: AM30EW-NZ-K-STD 76.00 (2.99) 61.60 (2.43) 23.00 (0.91) Ø3.30 31.50 (1.24) Pin Out Specifications 1 2 3 4 5 6 Top View Pin Single Dual 1 2 3 4 5 6 On/Off Control -Vin +Vin Trim - Vout + Vout On/Off Control -Vin +Vin - Vout Common + Vout Side View 9.80 (0.39) 22.20 (0.87) 25.80 (1.00) Ø3.30 Note: Unit: mm (inch) Mounting rail: TS35 Wire range: 24-12 AWG Tightening torque: Max 0.4 N*m General tolerances: ±0.50 (±0.02) DIN-RAIL with heatsink Option: AM30EW-NZ-K-STD Top View 76.00 (2.99) 61.60 (2.43) 23.00 (0.91) 31.50 (1.24) Ø3.30 1 2 3 4 5 6 www.aimtec.com F 051e R13.C REV:05/21/A Side View 9.80 (0.39) 25.80 (1.00) 25.80 (1.00) 22.20 (0.87) Ø3.30 Tel: +1 514 620 2722 5 of 10 Note: Unit: mm (inch) Mounting rail: TS35 Wire range: 24-12 AWG Tightening torque: Max 0.4 N*m General tolerances: ±0.50 (±0.02) Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM30EW-NZ 30 Watt | DC-DC Converter Derating Single output: 3.3V/5VDC output Single output: 9V/12V/15V/24VDC output Free Air Convection Free Air Convection Without heatsink Without heatsink 100 With heatsink Output Power (%) Output Power (%) 100 With heatsink 80 Safe Operating Area 60 40 Safe Operating Area 60 40 20 20 0 0 - 40 80 - 20 0 20 40 50 55 60 80 - 40 100 - 20 0 20 40 50 60 80 100 Ambient Temperature º C Ambient Temperature º C Dual output: Free Air Convection Without heatsink Output Power (%) 100 With heatsink 80 Safe Operating Area 60 40 20 0 - 40 - 20 0 20 40 50 55 60 80 100 Ambient Temperature º C NOTE: With operations at 12V nominal input (9-18VDC) the output power will be rated at 80% only. Typical application circuit Single output models + Vin + Vin C1 100uF Vin www.aimtec.com F 051e R13.C REV:05/21/A + DC +Vout + Vout + DC C2 - Vin - Vout Tel: +1 514 620 2722 6 of 10 - Vout Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM30EW-NZ 30 Watt | DC-DC Converter Dual output models + Vin C1 100uF C2, C3 + C2 + DC DC Common + - Vin - Vin Model +Vout + Vout + Vin C3 - Vout Single output models 3.3V/5V/9V Vout 12V/15V/24V Vout 220µF 100µF - Vout Dual output models ±5V/±12V/±15V Vout ±24V Vout 220µF 100µF EMC recommended external filter Single output models CY1 1nF/2KV LCM 1mH FUSE + Vin + + MOV C1 +Vout + Vout + Vin C2 DC DC C3 - Vin - Vin - Vout C4 - Vout CY2 1nF/2KV Model FUSE MOV C1 C2 C3 C4 www.aimtec.com F 051e R13.C REV:05/21/A 24V Vin 48V Vin Choose based on actual input current S20K30 S14K60 680µF/50V 330µF/100V 4.7µF/50V 2.2µF/100V 330µF/50V 330µF/100V Refer to the C2 in typical application circuit Tel: +1 514 620 2722 7 of 10 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM30EW-NZ 30 Watt | DC-DC Converter Dual output models CY1 2.2nF/400VAC FUSE + Vin + MOV C1 + C5 + C2 LDM 3.3uH C3 DC DC C4 Common + - Vin - Vin +Vout + Vout + Vin - Vout C6 - Vout CY2 2.2nF/400VAC Model FUSE MOV C1 C2, C3 C4 C5 24V Vin 48V Vin Choose based on actual input current S20K30 S14K60 680µF/50V 330µF/100V 2.2µF/50V 2.2µF/100V 330µF/50V 330µF/100V Refer to the C2 in typical application circuit Trimming Output voltage can be externally trimmed by utilizing the methods as shown below Fixed Resistor Variable Potentiometer Leave open if not used. www.aimtec.com F 051e R13.C REV:05/21/A Tel: +1 514 620 2722 8 of 10 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM30EW-NZ 30 Watt | DC-DC Converter AM30EW-xx03S-NZ Trim down % 1 Vout (VDC) 3.267 Rt down (KΩ) 193.344 Trim up % 1 Vout (VDC) 3.333 Rt up (KΩ) 305.949 2 3.234 106.818 2 3.366 102.749 3 3.201 70.696 3 3.399 57.886 4 3.168 50.870 4 3.432 38.180 5 3.135 38.341 5 3.465 27.104 6 3.102 29.708 6 3.498 20.007 7 3.069 23.397 7 3.531 15.072 8 3.036 18.583 8 3.564 11.442 9 3.003 14.790 9 3.597 8.658 10 2.97 11.724 10 3.63 6.457 AM30EW-xx05S-NZ Trim down % 1 Vout (VDC) 4.95 Rt down (KΩ) 105.181 Trim up % 1 Vout (VDC) 5.05 Rt up (KΩ) 176.356 2 4.9 52.154 2 5.1 71.279 3 4.85 31.997 3 5.15 41.974 4 4.8 21.378 4 5.2 28.200 5 4.75 14.823 5 5.25 20.198 6 4.7 10.373 6 5.3 14.967 7 4.65 7.155 7 5.35 11.281 8 4.6 4.719 8 5.4 8.544 9 4.55 2.811 9 5.45 6.430 10 4.5 1.277 10 5.5 4.749 AM30EW-xx09S-NZ Trim down % 1 Vout (VDC) 8.91 Rt down (KΩ) 375.533 Trim up % 1 Vout (VDC) 9.09 Rt up (KΩ) 314.532 2 8.82 207.430 2 9.18 112.639 3 8.73 139.157 3 9.27 64.148 4 8.64 102.145 4 9.36 42.357 5 8.55 78.924 5 9.45 29.975 6 8.46 62.997 6 9.54 21.990 7 8.37 51.393 7 9.63 16.412 8 8.28 42.562 8 9.72 12.297 9 8.19 35.617 9 9.81 9.134 10 8.1 30.011 10 9.9 6.629 AM30EW-xx12S-NZ Trim down % 1 Vout (VDC) 11.88 Rt down (KΩ) 496.092 Trim up % 1 Vout (VDC) 12.12 Rt up (KΩ) 706.435 2 11.76 301.452 2 12.24 158.920 3 11.64 212.527 3 12.36 83.879 4 11.52 161.585 4 12.48 54.075 5 11.4 128.573 5 12.6 38.077 6 11.28 105.442 6 12.72 28.095 7 11.16 88.332 7 12.84 21.274 8 11.04 75.164 8 12.96 16.317 9 10.92 64.716 9 13.08 12.552 10 10.8 56.223 10 13.2 9.595 AM30EW-xx15S-NZ Trim down % 1 Vout (VDC) 14.85 Rt down (KΩ) 634.883 Trim up % 1 Vout (VDC) 15.15 Rt up (KΩ) 1460.099 2 14.7 400.637 2 15.3 192.574 3 14.55 288.514 3 15.45 96.642 4 14.4 222.759 4 15.6 61.354 5 14.25 179.537 5 15.75 43.016 6 14.1 148.960 6 15.9 31.781 7 13.95 126.187 7 16.05 24.191 8 13.8 108.569 8 16.2 18.721 9 13.65 94.532 9 16.35 14.590 10 13.5 83.087 10 16.5 11.361 www.aimtec.com F 051e R13.C REV:05/21/A Tel: +1 514 620 2722 9 of 10 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM30EW-NZ 30 Watt | DC-DC Converter AM30EW-xx24S-NZ, xx=24 or 48 Trim down % 1 2 Vout (VDC) 23.76 23.52 Rt down (KΩ) 1286.200 792.123 Trim up % 1 2 Vout (VDC) 24.24 24.48 Rt up (KΩ) 816.889 179.914 3 23.28 565.867 3 24.72 94.338 4 23.04 436.104 4 24.96 60.464 5 22.8 351.954 5 25.2 42.307 6 22.56 292.963 6 25.44 30.988 7 22.32 249.315 7 25.68 23.257 8 22.08 215.714 8 25.92 17.640 9 21.84 189.047 9 26.16 13.376 10 21.6 167.370 10 26.4 10.027 NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the date manufactured. 3. Mechanical drawings and specifications are for reference only. 4. All specifications are measured at an ambient temperature of 25°C, humidity