AM6C-2415S-NZ

Series AM6C-NZ 6 Watt | DC-DC Converter FEATURES: • Wide input voltage range (2:1) • Efficiency up to 88% • Isolation voltage of 1500VDC • Input under voltage lockout • • • • Operating temperature: -40 ºC to +85 ºC No load consumption ≤ 0.12W Continuous Short Circuit Protection Over Current, Over Voltage Protection Models Single output Model Input Voltage (V) Output Voltage (V) Output Current max (mA) Isolation (VDC) Max Capacitive Load(uF) Efficiency (%) 9-18 9-18 18-36 18-36 18-36 18-36 18-36 5 12 3.3 5 12 15 24 1200 500 1500 1200 500 400 250 1500 1500 1500 1500 1500 1500 1500 1000 470 1800 1000 470 220 100 81 85 77 82 85 86 87 Input Voltage (V) Output Voltage (V) Output Current max (mA) Isolation (VDC) Max Capacitive Load(uF) Efficiency (%) AM6C-1205S-NZ AM6C-1212S-NZ AM6C-2403S-NZ AM6C-2405S-NZ AM6C-2412S-NZ AM6C-2415S-NZ AM6C-2424S-NZ Models Dual output Model AM6C-1205D-NZ‡ 9-18 ±5 ±600 1500 470 81 AM6C-1212D-NZ‡ 9-18 ±12 ±250 1500 100 85 AM6C-2405D-NZ‡ 18-36 ±5 ±600 1500 470 83 AM6C-2412D-NZ‡ 18-36 ±12 ±250 1500 100 87 AM6C-2415D-NZ‡ 18-36 ±15 ±200 1500 100 87 Only the model AM6C-2405S-NZ can add suffix “-ST” for optional screw terminal bottom plate or “-STD” for optional DIN Rail screw terminal bottom plate and reverse voltage protection. The optional package will be EOL by 30 Dec, 2020. *‡ - Reference the Safety table NOTE: All specifications in this datasheet are measured at an ambient temperature of 25°C, humidity1000 1000 Tel: +1 514 620 2722 1 of 5 Rated Units 1500 VDC MOhm pF Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM6C-NZ 6 Watt | DC-DC Converter Output Specifications Parameters Conditions Voltage accuracy Voltage balance (Dual Output Models) Cross Regulation (Dual Output Models) Over voltage protection Short Circuit protection Over current protection Line voltage regulation Load voltage regulation Temperature coefficient Ripple & Noise Transient recovery time Transient recovery deviation Balanced Load 50% load on one output – 10% to 100% load on second load LL-HL, full load 5% -100% load Full load 20MHz Bandwidth 25% load step change 25% load step change Typical Maximum Units ±2 ±1.5 ±3 % % ±5 % 110-160 Continuous, Auto recovery 110-190 ±1 ±1.5 ±0.03 75 500 ±5 % of Vout ±8 % of Iout % of Vin % %/oC mV p-p µs % General Specifications Parameters Switching frequency Operating temperature Storage temperature Maximum case temperature Cooling Humidity Case material Weight Dimensions (L x W x H) MTBF Maximum soldering temperature Conditions Typical 100% load With derating above 71ºC 300 Maximum Units 105 KHz o C o C o C 95 % RH -40 to +85 -55 to +125 Free convection Aluminum alloy Pin mountable 14 -ST option 36 g -STD option 56 Aluminum case 1 x 1 x 0.46 inches 25.40 x 25.40 x 11.70 mm Optional packages See dimensions drawing >1,000,000 hours (MIL-HDBK -217F, Ground Benign, t=+25oC) o 10sec, 1.5mm from case 300 C Environmental Specifications Parameters Test mode Acceleration Vibration 10-55Hz 10G, 30min one cycle, every axis tested Safety Specifications Parameters Approval Standards UL (models marked with ‡) Information Technology Equipment Electrostatic Discharge Immunity RF, Electromagnetic Field Immunity Electrical Fast Transient / Burst Immunity Surge Immunity RF, Conducted Disturbance Immunity Voltage dips, Short interruptions and Voltage Variations Immunity www.aimtec.com F 051e R13.D REV: 05/20/A UL60950-1 EN55022 Class B, with the recommended circuit below, EN55024 IEC 61000-4-2, Contact ±4KV, Criteria B IEC 61000-4-3, 10V/m, Criteria A IEC 61000-4-4, ±2KV, Criteria B, with the recommended circuit below IEC 61000-4-5, ±2KV, Criteria B, with the recommended circuit below IEC 61000-4-6, 3 Vrms, Criteria A IEC61000-4-29, 0-70%, Criteria B Tel: +1 514 620 2722 2 of 5 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM6C-NZ 6 Watt | DC-DC Converter Dimensions Pin Out Specifications Bottom View 2.54 (0.10) Top View 25.40 (1.00) 10.16 2.54 (0.40) (0.10) 10.16 (0.40) 4 20.32 (0.80) 25.40 (1.00) 3 +V -V Input Input 2.54 (0.10) 1 Side View 5 +V Output -V Output Common 10.16 (0.40) 2 Pin 1 2 3 4 5 Single +V Input -V Input +V Output No pin -V Output Dual +V Input -V Input +V Output Common -V Output 5.08 (0.20) 11.70 (0.46) Printed Face 1.00 (0.39) 4.10 (0.16) 2.54 (0.10) Notes: All dimensions are typical in millimeters (inches).
 Case Tolerance ±0.25 (±0.01) Pin diameter tolerance ±0.1 (±0.004) Pin height tolerance ±0.5 (±0.02) Dimensions with -ST options Pin Out Specifications 76.00 (2.99) Pin 61.60 (2.43) LED light 31.50 (1.24) 2 Top view 3 5 23.00 (0.91) 4 1 6 1 2 3 4 5 6 Single No Connection -V Input +V Input -V Output No Connection +V Output Dual No Connection -V Input +V Input -V Output Common +V Output Ø3.30 Ø0.13 8.80 (0.35) 21.20 (0.84) Side view Dimensions with -STD options Dimensions: mm (inch) Case Tolerance:± 0.50 (0.02) Wire gauge: 24-12AWG Torque Tightening: Max 0.4N*m Pin Out Specifications 76.00 (2.99) Pin 61.60 (2.43) LED light 31.50 (1.24) 2 Top view 3 5 23.00 (0.91) 4 1 6 8.80 (0.35) 21.20 (0.84) Side view www.aimtec.com F 051e R13.D REV: 05/20/A 1 2 3 4 5 6 Single No Connection -V Input +V Input -V Output No Connection +V Output Dual No Connection -V Input +V Input -V Output Common +V Output Dimensions: mm (inch) Case Tolerance:± 0.50 (0.02) Wire gauge: 24-12AWG Mounting Rail: TS35 Torque Tightening: Max 0.4N*m Tel: +1 514 620 2722 3 of 5 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM6C-NZ 6 Watt | DC-DC Converter Derating Free Air Convection 71º C Output Power (%) 100 80 Safe Operating Area 60 40 20 0 - 40 - 20 0 20 40 60 80 85 100 Ambient Temperature º C EMC recommended circuit 1nF/2KV LDM 4.7µH F1 +Vin MOV CY1 C1 +Vo C3 C2 DC-DC Converter -Vin -Vo CY2 1nF/2KV MOV C1 C2 C3 12V input 24V input S14K20 S20K30 1000µF/35V 1000µF/50V 1µF/50V 10µF/50V 48V input S14K60 330µF/100V 1µF/100V 10µF/100V NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the date manufactured. 3. Mechanical drawings and specifications are for reference only. 4. All specifications are measured at an ambient temperature of 25°C, humidity