AM6T-0512D-NZ

Series AM6T-NZ 6 Watt | DC-DC Converter FEATURES: • • • • Wide 2:1 input range Over Voltage Protection High efficiency up to 87% Low Ripple and Noise • Operating temperature -40oC to + 85oC • Input / Output isolation 1500 VDC • Continuous short circuit protection Models Single output Model AM6T-0505S-NZ AM6T-0512S-NZ AM6T-0515S-NZ AM6T-0524S-NZ AM6T-1203S-NZ AM6T-1205S-NZ AM6T-1212S-NZ AM6T-1215S-NZ AM6T-1224S-NZ AM6T-2403S-NZ AM6T-2405S-NZ AM6T-2412S-NZ AM6T-2415S-NZ AM6T-2424S-NZ AM6T-4803S-NZ AM6T-4805S-NZ AM6T-4812S-NZ AM6T-4815S-NZ AM6T-4824S-NZ Input Voltage (V) Output Voltage (V) Output Current max(mA) Isolation (VDC) Efficiency (%) 4.5-9 4.5-9 4.5-9 4.5-9 9-18 9-18 9-18 9-18 9-18 18-36 18-36 18-36 18-36 18-36 36-75 36-75 36-75 36-75 36-75 5 12 15 24 3.3 5 12 15 24 3.3 5 12 15 24 3.3 5 12 15 24 1200 500 400 250 1500 1200 500 400 250 1500 1200 500 400 250 1500 1200 500 400 250 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 78 84 84 84 75 80 84 85 85 78 82 85 86 86 79 83 87 88 87 Input Voltage (V) Output Voltage (V) Output Current max (mA) Isolation (VDC) Efficiency (%) 4.5-9 4.5-9 4.5-9 4.5-9 9-18 9-18 9-18 9-18 18-36 18-36 18-36 18-36 36-75 36-75 36-75 36-75 ±5 ±12 ±15 ±24 ±5 ±12 ±15 ±24 ±5 ±12 ±15 ±24 ±5 ±12 ±15 ±24 ±600 ±250 ±200 ±125 ±600 ±250 ±200 ±125 ±600 ±250 ±200 ±125 ±600 ±250 ±200 ±125 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 78 84 84 84 80 84 85 84 83 86 87 85 83 87 85 85 Models Dual output Model AM6T-0505D-NZ AM6T-0512D-NZ AM6T-0515D-NZ AM6T-0524D-NZ AM6T-1205D-NZ AM6T-1212D-NZ AM6T-1215D-NZ AM6T-1224D-NZ AM6T-2405D-NZ AM6T-2412D-NZ AM6T-2415D-NZ AM6T-2424D-NZ AM6T-4805D-NZ AM6T-4812D-NZ AM6T-4815D-NZ AM6T-4824D-NZ NOTE: All specifications in this datasheet are measured at an ambient temperature of 25°C, humidity 1000 1000 Conditions Typical Maximum Units VDC VDC MOhm pF Output Specifications Parameters Voltage accuracy 5 Vin Vo1, 5% to 100% Load 5 Vin Vo2, 5% to 100% Load Other models, 5% to 100% Load Short Circuit protection Short circuit restart Line voltage regulation Load voltage regulation Cross Regulation (dual) Temperature coefficient Transient Recovery Time Transient Response Deviation Ripple& Noise Over Voltage Protection Over current protection Maximum Units ±2 ±3 ±3 % ±1 ±1 ±1 Continuous Auto-recovery ±0.2 ±0.5 Vo1, Full Load, LL-HL Vo2, Full Load, LL-HL 5 Vin Vo1, 5% to 100% Load 5 Vin Vo2, 5% to 100% Load Other models Vo1, 5% to 100% Load Other models Vo1, 5% to 100% Load Vo1 50% load, Vo2 10-100% load ±0.5 ±1 ±1 ±1.5 ±1 ±1.5 ±5 ±0.5 ±0.5 ±0.03 300 ±5 ±3 25% load step 3.3V, 5V, ±5Vout, 25% load step Others, 25% load step 5% to 100% Load % % % %/oC µsec 140 500 ±8 ±5 100 110 to 160 190 mVp-p %Vout %Iout Conditions Typical Maximum Units 100% load Derating above +71 300 % General Specifications Parameters Switching frequency* Operating temperature Storage temperature Max Case temperature Cooling Humidity Case material Weight Dimensions (L x W x H) MTBF -40 to +85 -55 to +125 100 KHz oC oC o C Free air convection 95 Black Anodized Aluminum % 12 g 1.26 x 0.79 x 0.42inches (32.00 x 20.00 x 10.80mm) >1 000 000 hrs (MIL-HDBK -217F, Ground Benign, t=+25oC) *Bellow 50% load the switching frequency decreases with the decrease of the load. Environment Specifications Test Parameters Conditions Vibration Test mode Acceleration 10-150Hz 5g, 30min, every axis tested www.aimtec.com F 051e R6.A REV/12/19/A Tel: +1 514 620 2722 2 of 4 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM6T-NZ 6 Watt | DC-DC Converter Safety Specifications Parameters Designed to meet IEC/UL 60950-1 CISPR32 / EN55032, Class A (without external components)(Except 5Vin model), Class B (with recommended EMC circuit part B)(5Vin model with recommended circuit) IEC61000-4-2, Contact ±4KV, Criteria B Standards Electrostatic Discharge Immunity RF, Electromagnetic Field Immunity IEC61000-4-3, 10V/m, Criteria A Electrical Fast Transient/Burst Immunity IEC61000-4-4, ±2KV, Criteria B, (with recommended EMC circuit part A) Surge Immunity IEC61000-4-5, L-L ±2KV, Criteria B, (with recommended EMC circuit part A) RF, Conducted Disturbance Immunity IEC61000-4-6, 3Vrms, Criteria A EMC - Radiated & Conducted emission Pin Out Specifications Dimensions 32.00 (1.26) 1500VDC -V Input -V Input Common -V Output +V Output Common +V Input +V Input 3 9 11 15.24 (0.60) -V Input -V Input No pin N.C. +V Output -V Output +V Input +V Input 20.00 (0.79) Dual Bottom View 23 22 16 2.54 (0.10) Printed Face 14 5.08 (0.20) Built-in Stand-offs to ease PCB cleaning 4.10 (0.16) 0.50 (0.02) 2 3 9 11 14 16 22 23 2 Single 10.30 (0.40) Pin 0.50 (0.02) Recommended Circuit For Ripple & Noise reduction Single Output +V output + V input + V input Cin Dual Output +V output + + DC DC Cin Cout - V input -V output + Cout + - V input DC DC Common + Cout -V output External Capacitor Tables Vin (VDC) Cin (uF) Cout (uF) 5/12/24 48 100 10 ~ 47 10 10 www.aimtec.com F 051e R6.A REV/12/19/A Tel: +1 514 620 2722 3 of 4 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM6T-NZ 6 Watt | DC-DC Converter Recommended EMC Circuit + Vin +Vout LDM 4.7µH FUSE C3 MOV CY2 C1 + Cout C2 + DC DC - Vin Model CY1 B A MOV 12 Vin S14K20 24 Vin S20K30 48 Vin S14K60 Note: Fuse is user selectable Part A for EMS, part B for EMI. - Vout C1 C2 C3 CY1/CY2 1µF / 50V 1µF / 50V 1µF / 100V 100µF / 35V 100µF / 50V 100µF / 100V 1000µF / 35V 1000µF / 50V 680µF / 100V 1nF/2KV Recommended EMC Circuit for 5V input model + Vin +Vout CY2 2.2nF/2KV FUSE + 10µF + 2200μF/ 35V 4.7μF/ 50V - Vin 100μF/ 35V LCM 2.2mH CY1 Or 2.2nF/2KV AMFC22-3NZ B A 4.7μF/ 50V DC DC - Vout Part A for EMS, part B for EMI. Derating Free Air Convection Other models 100 Output Power (%) 5Vin model 80 65 60 Safe Operating Area 40 20 0 - 40 - 20 0 20 40 60 71 75 80 85 100 Ambient Temperature º C NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the date manufactured. 3.Mechanical drawings and specifications are for reference only. 4.All specifications are measured at an ambient temperature of 25°C, humidity