AMLBW-3635Z

Click on Series name for product info on aimtec.com Series AMLBW-Z Up to 700mA | Step Up LED Driver FEATURES: • Step UP DC/DC LED driver • Constant current output • High efficiency up to 95% • Soft Start • IP67 Case • • • • • Operating Temperature 40ºC to +85ºC Open and Short circuit LED Protection 2”x1” case package Drives LED strings of up to 48V PWM/Digital and Analog Voltage dimming Models Single output Model Input Voltage (V) AMLBW-3615Z AMLBW-3625Z AMLBW-3630Z AMLBW-3635Z 9-36 9-36 9-36 9-36 Output Voltage (V) Vo-Vin≥5V Maximum Rated Current (mA) Max Capacitive load (µF) Efficiency (%) Ripple & Noise (mV p-p) 14-48 150 100 91 350 14-48 250 100 93 450 14-48 300 100 94 450 14-48 350 100 94 600 14-45 (Vin:9V-18V) AMLBW-3650Z 9-36 500 47 95 650 23-48 (Vin: 18V-36V) 14-38 (Vin:9V-18V) AMLBW-3660Z 9-36 600 47 95 650 23-48 (Vin: 18V-36V) 14-32 (Vin:9V-18V) AMLBW-3670Z 9-36 700 47 95 700 23-48 (Vin: 18V-36V AMLBW-3690Z 20-30 25-48 900 47 95 400 NOTE: All specifications in this datasheet are measured at an ambient temperature of 25°C, humidity 838 000 hrs (MIL-HDBK-217 F at +25 °C) 1.5mm from case for 10sec. 260 % RH g °C 1. To prevent burning out the driver, the output voltage must be 5.0VDC higher than the input voltage. 2. Do NOT exceed the maximum power ratings on each model. 3. With output ripple being rather low, it is recommended not to increase the additional output capacitor as this will increase the delay while starting up under cool start conditions. 4. This series offers protection in case the output is shorted. After the short occurs, the input current will be cut off and recovers when the short is removed. 5. The reference value of under voltage protection (7.6V) means that under the condition of cool start and full discharge of output, the protection starts when input voltage is lower than 7.6V. 6. Note: PWM dimming means PWM signals are converted into mimic analog voltage by internal circuits and then do the dimming. The advantage of this approach is to reduce the EMI. Safety Specifications Parameters Agency approvals Standards www.aimtec.com F 051e R12.C Rev: 12/21/A CE Designed to meet IEC/EN 60950-1, UL8750, IEC/EN 61347-2-13 EMI EN 55015 (CISPR22) EMC immunity EN 61547 Electrostatic Discharge Immunity IEC 61000-4-2 Perf. Criteria A RF, Electromagnetic Field Immunity IEC 61000-4-3 Perf. Criteria A Electrical Fast Transient/Burst Immunity IEC 61000-4-4 Perf. Criteria A Surge Immunity IEC 61000-4-5 Perf. Criteria A RF, Conducted Disturbance Immunity IEC 61000-4-6 Perf. Criteria A Power frequency Magnetic Field Immunity IEC 61000-4-8 Perf. Criteria A Tel: +1 514 620 2722 2 of 7 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AMLBW-Z Up to 700mA | Step Up LED Driver Pin Out Specifications Pin 1 2 3 4 5 6 Color Red White Blue Black Yellow Black Single +Vi DIM EN -Vi +LED -LED Description + DC Supply PWM/Analog Dimming Control Remote ON/OFF -DC Supply LED Anode connection LED Cathode connection Dimensions 44.62 (1.76) 1 Aimtec 26.10 (1.03) 16.48 (0.65) 2 3 5 Top view 4 20.32 (0.80) 51.50 (2.03) 6 45.72 (1.80) 15.80 (0.62) 4 3 6 4 100.0 (3.94) 2 6 Bottom view 10.00 (0.39) 1 5 Unit: mm(inch) Cas e tolerance: ±0. 5(0. 02) Wire core diameter: 0.8 ±0.1(0.03 1±0.0 04) & 1.4 ±0.1(0.05 5±0.0 04) Wire outer diameter: 2.4 ±0.1(0.09 4±0.0 04) & 1.4± 0.1(0.106 ±0.00 4) Wire: 1 8AWG UL101 5/CSA TEM listed / 600 V / 1 05°C Rated 22AW G UL101 5/CSA TEM listed / 600 V / 1 05°C Rated Stripped and tinned Operating Temperature Free Air Convection AMLBW-3615Z (Vin:9V-36V) AMLBW-3625Z (Vin:18V-36V) AMLBW-3630Z (Vin:18V-36V) AMLBW-3635Z (Vin: 18V-36V) Output Power (%) 100 AMLBW-3650Z (Vin:18V-36V) AMLBW-3625Z (Vin:9V-18V) AMLBW-3630Z (Vin:9V-18V) 80 AMLBW-3635Z (Vin:9V-18V) AMLBW-3660Z (Vin:18V-36V) AMLBW-3670Z (Vin:18V-36V) 60 Safe Operating Area 40 AMLBW-3650Z (Vin:9V-18V) AMLBW-3660Z (Vin:9V-18V) AMLBW-3670Z (Vin:9V-18V) 20 AMLBW-3690Z (Vin:20V-30V) 0 - 40 - 20 0 20 40 65 70 75 85 60 80 Ambient Temperature www.aimtec.com F 051e R12.C Rev: 12/21/A ºC Tel: +1 514 620 2722 3 of 7 100 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AMLBW-Z Up to 700mA | Step Up LED Driver EMC recommended circuit: +Vin 14uH/4A +Vi +LED 1 5 1 AMLBW-Z 6 4 47uF/ 100V 14uH/4A 330uF/ 100V 330uF/ 100V 5.6mH/5A Common Choke -Vin -Vi 1st LED 2 3 1 DIM PWM/Analog Dimming Control EN -LED Last LED Application circuit examples: AC In 6.5Vac to 25Vac +Vin + +LED AMLBW-Z 100 to 330uF 0.1uF optional +V output -Vin 1st LED 1 -V output Last LED 1 AC In DIM -Vout +Vout +Vin 1 1 1 1 1st LED DIM Analogue DIM PWM Dim/ON/OFF EN Last LED 1st LED 1 AMLBW-Z -Vout -Vin EN 1 DIM -Vout Last LED EN Analogue DIM PWM Dim/ON/OFF AMLBW-Z -Vin 1 DIM +Vout 1 LED -Vin -LED st 1 AMLBW-Z EN +Vin +Vout +Vin PWM/Analog Dimming Control Analogue DIM PWM Dim/ON/OFF www.aimtec.com F 051e R12.C Rev: 12/21/A Last LED SW SW Vout ON OFF 0V normal Tel: +1 514 620 2722 4 of 7 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AMLBW-Z Up to 700mA | Step Up LED Driver Under Voltage Protection +Vout +Vin st 1 LED R1 1 AMLBW-Z -Vout -Vin EN 1 DIM Analogue DIM PWM Dim/ON/OFF Last LED R1 *R1 Value only supplies the reference Under Voltage Protection 900mA model Other models On (V) Off (V) On (V) Off (V) X 12K 10K 7.5K 4.7K 3.3K 2.7K 2.4K 2.0K 1.8K 15.6 21.5 22.5 25.0 - 14.6 19.7 20.7 22.5 - 7.6 11.0 11.5 13.0 16.2 20.5 23.2 25.0 28.5 30.8 6.8 10.2 10.7 12.2 15.4 19.7 22.2 24.0 27.5 29.8 Output Current Adjustment by External DC Control Voltage (DIM): Vctrl R1 +Vout 0.4 -1.7V DIM +5v +Vout 380K 1st LED 1 AMLBW-Z R2 -Vout -Vin 200K AMLBW-Z DIM 0 -1.7V Last LED 1st LED 1 -Vout -Vin 1 1 EN GND +Vin Vctrl 0 to +10V R1 R1 1M +Vout R2 210K DIM 0 -1.7V -Vin -Vout +Vout R2 380K 1st LED 1 AMLBW-Z If Vin is between 9 VDC and 36 VDC it is recommended to use the circuit shown below 1 TL431 AMLBW-Z DIM 200K -Vout -Vin 1 1 Vin 5V 12V 24V 36V www.aimtec.com F 051e R12.C Rev: 12/21/A 1st LED 1 Tel: +1 514 620 2722 5 of 7 R1 4.7K 18K 43K 62K Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AMLBW-Z Up to 700mA | Step Up LED Driver Output Current Adjustment by PWM Control: A Pulse Width Modulation (PWM) signal with a duty cycle DPWM can be applied to the DIM pin as shown below. +Vin +LED 1 1 AMLBW-Z -Vin 4 6 PWM 5V 1st LED 5 2 DIM Last LED 3 0V 1 EN -LED Driving DIM Via Open Collector Transistor The DIM pin can also be driven via an open collector transistor as shown below. +5V 12K +LED +Vin 1 PWM 1st LED 5 1 AMLBW-Z 210 6 4 -Vin 2 2SD1782K DIM GND Last LED 3 1 EN -LED Driving the DIM from a Microcontroller The DIM can be driven from an open drain output of a microcontroller as shown below. +5V 12K +Vin MCU +LED 4 -Vin 2SK3018 6 Last LED 3 1 DIM GND F 051e R12.C Rev: 12/21/A 1 AMLBW-Z 2 www.aimtec.com 1st LED 5 1 Tel: +1 514 620 2722 6 of 7 EN -LED Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AMLBW-Z Up to 700mA | Step Up LED Driver Output Current Adjustment by PWM Control (Dimming): A PWM signal must have a frequency of greater than 100Hz to prevent any visible flicker. Output Current Adjustment by PWM Control (Flash): Output Current vs DIM Voltage NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the date manufactured. 3. Mechanical drawings and specifications are for reference only. 4. All specifications are measured at an ambient temperature of 25°C, humidity